From: Johan Hovold <johan+linaro@kernel.org>
To: Vinod Koul <vkoul@kernel.org>
Cc: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@somainline.org>,
Kishon Vijay Abraham I <kishon@ti.com>,
Dmitry Baryshkov <dmitry.baryshkov@linaro.org>,
linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
linux-kernel@vger.kernel.org,
Johan Hovold <johan+linaro@kernel.org>
Subject: [PATCH v2 05/14] phy: qcom-qmp-pcie-msm8996: drop unused in-layout configuration
Date: Wed, 12 Oct 2022 10:12:32 +0200 [thread overview]
Message-ID: <20221012081241.18273-6-johan+linaro@kernel.org> (raw)
In-Reply-To: <20221012081241.18273-1-johan+linaro@kernel.org>
The MSM8996 QMP PCIe PHY driver no longer uses the "in-layout"
configuration macro to configure registers that are typically accessed
using "regs_layout" arrays (e.g. QPHY_START_CTRL) so drop this unused
feature.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
---
.../phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c | 34 ++++---------------
1 file changed, 6 insertions(+), 28 deletions(-)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c
index 8b74948eb467..31ac405d3785 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c
@@ -46,11 +46,6 @@
struct qmp_phy_init_tbl {
unsigned int offset;
unsigned int val;
- /*
- * register part of layout ?
- * if yes, then offset gives index in the reg-layout
- */
- bool in_layout;
/*
* mask of lanes for which this register is written
* for cases when second lane needs different values
@@ -65,14 +60,6 @@ struct qmp_phy_init_tbl {
.lane_mask = 0xff, \
}
-#define QMP_PHY_INIT_CFG_L(o, v) \
- { \
- .offset = o, \
- .val = v, \
- .in_layout = true, \
- .lane_mask = 0xff, \
- }
-
#define QMP_PHY_INIT_CFG_LANE(o, v, l) \
{ \
.offset = o, \
@@ -346,7 +333,6 @@ static const struct qmp_phy_cfg msm8996_pciephy_cfg = {
};
static void qmp_pcie_msm8996_configure_lane(void __iomem *base,
- const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
int num,
u8 lane_mask)
@@ -361,19 +347,15 @@ static void qmp_pcie_msm8996_configure_lane(void __iomem *base,
if (!(t->lane_mask & lane_mask))
continue;
- if (t->in_layout)
- writel(t->val, base + regs[t->offset]);
- else
- writel(t->val, base + t->offset);
+ writel(t->val, base + t->offset);
}
}
static void qmp_pcie_msm8996_configure(void __iomem *base,
- const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
int num)
{
- qmp_pcie_msm8996_configure_lane(base, regs, tbl, num, 0xff);
+ qmp_pcie_msm8996_configure_lane(base, tbl, num, 0xff);
}
static int qmp_pcie_msm8996_serdes_init(struct qmp_phy *qphy)
@@ -387,7 +369,7 @@ static int qmp_pcie_msm8996_serdes_init(struct qmp_phy *qphy)
unsigned int mask, val;
int ret;
- qmp_pcie_msm8996_configure(serdes, cfg->regs, serdes_tbl, serdes_tbl_num);
+ qmp_pcie_msm8996_configure(serdes, serdes_tbl, serdes_tbl_num);
qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
@@ -531,13 +513,9 @@ static int qmp_pcie_msm8996_power_on(struct phy *phy)
}
/* Tx, Rx, and PCS configurations */
- qmp_pcie_msm8996_configure_lane(tx, cfg->regs, cfg->tx_tbl,
- cfg->tx_tbl_num, 1);
-
- qmp_pcie_msm8996_configure_lane(rx, cfg->regs, cfg->rx_tbl,
- cfg->rx_tbl_num, 1);
-
- qmp_pcie_msm8996_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+ qmp_pcie_msm8996_configure_lane(tx, cfg->tx_tbl, cfg->tx_tbl_num, 1);
+ qmp_pcie_msm8996_configure_lane(rx, cfg->rx_tbl, cfg->rx_tbl_num, 1);
+ qmp_pcie_msm8996_configure(pcs, cfg->pcs_tbl, cfg->pcs_tbl_num);
/*
* Pull out PHY from POWER DOWN state.
--
2.35.1
next prev parent reply other threads:[~2022-10-12 8:16 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-12 8:12 [PATCH v2 00/14] phy: qcom-qmp: further prep cleanups Johan Hovold
2022-10-12 8:12 ` [PATCH v2 01/14] phy: qcom-qmp: drop regulator error message Johan Hovold
2022-10-12 8:12 ` [PATCH v2 02/14] phy: qcom-qmp: drop superfluous comments Johan Hovold
2022-10-12 8:12 ` [PATCH v2 03/14] phy: qcom-qmp-combo: drop unused in-layout configuration Johan Hovold
2022-10-12 8:12 ` [PATCH v2 04/14] phy: qcom-qmp-pcie: drop redundant ipq8074 power on Johan Hovold
2022-10-12 8:12 ` Johan Hovold [this message]
2022-10-12 8:12 ` [PATCH v2 06/14] phy: qcom-qmp-ufs: drop unused in-layout configuration Johan Hovold
2022-10-12 8:12 ` [PATCH v2 07/14] phy: qcom-qmp-usb: " Johan Hovold
2022-10-12 20:39 ` Dmitry Baryshkov
2022-10-12 8:12 ` [PATCH v2 08/14] phy: qcom-qmp-pcie: drop power-down delay config Johan Hovold
2022-10-12 8:12 ` [PATCH v2 09/14] phy: qcom-qmp-pcie: replace power-down delay Johan Hovold
2022-10-12 20:40 ` Dmitry Baryshkov
2022-10-12 8:12 ` [PATCH v2 10/14] phy: qcom-qmp-pcie-msm8996: drop power-down delay config Johan Hovold
2022-10-12 8:12 ` [PATCH v2 11/14] phy: qcom-qmp-combo: drop sc8280xp power-down delay Johan Hovold
2022-10-12 20:41 ` Dmitry Baryshkov
2022-10-12 8:12 ` [PATCH v2 12/14] phy: qcom-qmp-combo: drop power-down delay config Johan Hovold
2022-10-12 8:12 ` [PATCH v2 13/14] phy: qcom-qmp-usb: drop sc8280xp power-down delay Johan Hovold
2022-10-12 20:41 ` Dmitry Baryshkov
2022-10-12 8:12 ` [PATCH v2 14/14] phy: qcom-qmp-usb: drop power-down delay config Johan Hovold
2022-10-12 12:35 ` [PATCH v2 00/14] phy: qcom-qmp: further prep cleanups Johan Hovold
2022-10-28 12:12 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221012081241.18273-6-johan+linaro@kernel.org \
--to=johan+linaro@kernel.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=kishon@ti.com \
--cc=konrad.dybcio@somainline.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).