Re: [PATCH] thermal/drivers/qcom: Remove duplicate set next trip point interrupt code

[Bjorn Andersson <andersson@kernel.org>]

On Tue, Jan 10, 2023 at 11:34:20AM +0100, Daniel Lezcano wrote:
> From: Daniel Lezcano <daniel.lezcano@linaro.org>
> 
> The tsens driver reprogram the next trip points in the irq
> handler. This function then call thermal_zone_device_update().
> 
> However, thermal_zone_device_update() calls thermal_zone_set_trips()
> and from there it calls the backend 'set_trips' ops. This one in turn
> reprogram the next trip points (low/high).
> 
> Consequently, the code setting the next trip points interrupt in the
> interrupt handle is not needed and could be removed.
> 


Reviewed-by: Bjorn Andersson <andersson@kernel.org>

> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
> Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>

The last one should be the address you sent your patch from, and that
was the first one. So I think you should drop this one.

Regards,
Bjorn

> ---
>  drivers/thermal/qcom/tsens.c | 46 +-----------------------------------
>  1 file changed, 1 insertion(+), 45 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index b5b136ff323f..58693ee8c430 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -472,52 +472,8 @@ static irqreturn_t tsens_irq_thread(int irq, void *data)
>  			continue;
>  		if (!tsens_threshold_violated(priv, hw_id, &d))
>  			continue;
> -		ret = get_temp_tsens_valid(s, &temp);
> -		if (ret) {
> -			dev_err(priv->dev, "[%u] %s: error reading sensor\n",
> -				hw_id, __func__);
> -			continue;
> -		}
>  
> -		spin_lock_irqsave(&priv->ul_lock, flags);
> -
> -		tsens_read_irq_state(priv, hw_id, s, &d);
> -
> -		if (d.up_viol &&
> -		    !masked_irq(hw_id, d.up_irq_mask, tsens_version(priv))) {
> -			tsens_set_interrupt(priv, hw_id, UPPER, disable);
> -			if (d.up_thresh > temp) {
> -				dev_dbg(priv->dev, "[%u] %s: re-arm upper\n",
> -					hw_id, __func__);
> -				tsens_set_interrupt(priv, hw_id, UPPER, enable);
> -			} else {
> -				trigger = true;
> -				/* Keep irq masked */
> -			}
> -		} else if (d.low_viol &&
> -			   !masked_irq(hw_id, d.low_irq_mask, tsens_version(priv))) {
> -			tsens_set_interrupt(priv, hw_id, LOWER, disable);
> -			if (d.low_thresh < temp) {
> -				dev_dbg(priv->dev, "[%u] %s: re-arm low\n",
> -					hw_id, __func__);
> -				tsens_set_interrupt(priv, hw_id, LOWER, enable);
> -			} else {
> -				trigger = true;
> -				/* Keep irq masked */
> -			}
> -		}
> -
> -		spin_unlock_irqrestore(&priv->ul_lock, flags);
> -
> -		if (trigger) {
> -			dev_dbg(priv->dev, "[%u] %s: TZ update trigger (%d mC)\n",
> -				hw_id, __func__, temp);
> -			thermal_zone_device_update(s->tzd,
> -						   THERMAL_EVENT_UNSPECIFIED);
> -		} else {
> -			dev_dbg(priv->dev, "[%u] %s: no violation:  %d\n",
> -				hw_id, __func__, temp);
> -		}
> +		thermal_zone_device_update(s->tzd, THERMAL_EVENT_UNSPECIFIED);
>  
>  		if (tsens_version(priv) < VER_0_1) {
>  			/* Constraint: There is only 1 interrupt control register for all
> -- 
> 2.34.1
>