Re: [PATCH v2 12/15] arm64: dts: qcom: sa8775p: pmic: add thermal zones

Bartosz Golaszewski
2023-03-22T15:31:15Z

On Wed, Mar 22, 2023 at 3:47 AM Bjorn Andersson <andersson@kernel.org> wrote:
>
> On Mon, Mar 20, 2023 at 06:28:20PM +0100, Konrad Dybcio wrote:
> >
> >
> > On 20.03.2023 16:48, Bartosz Golaszewski wrote:
> > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > >
> > > Add the thermal zones and associated alarm nodes for the PMICs that have
> > > them hooked up on sa8775p-ride.
> > >
> > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > > ---
> > > arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 58 +++++++++++++++++++++
> > > 1 file changed, 58 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> > > index 8616ead3daf5..276070b62ccd 100644
> > > --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> > > @@ -6,6 +6,50 @@
> > > #include <dt-bindings/input/input.h>
> > > #include <dt-bindings/spmi/spmi.h>
> > >
> > > +/ {
> > > + thermal-zones {
> > > + pmm8654au_1_thermal: pm8775-1-thermal {
> > Please reindex this, downstream uses _1 for pmic@0, but this
> > makes little sense. Make it match the SID.
> >
>
> Please use the naming from the schematics for these things, rather than
> just an iterator (which might be what Bartosz is doing here).
>

Not sure how to approach that. All currently existing
"qcom,spmi-temp-alarm" nodes use the PMIC name for the label.
Otherwise it would have to go into the board file and be replicated
for each board using the same PMIC?

Bart

> Regards,
> Bjorn
>
> > > + polling-delay-passive = <100>;
> > > + polling-delay = <0>;
> > > + thermal-sensors = <&pmm8654au_1_temp_alarm>;
> > > +
> > > + trips {
> > > + trip0 {
> > > + temperature = <105000>;
> > > + hysteresis = <0>;
> > > + type = "passive";
> > > + };
> > > +
> > > + trip1 {
> > > + temperature = <125000>;
> > > + hysteresis = <0>;
> > > + type = "critical";
> > > + };
> > > + };
> > > + };
> > > +
> > What happened to the downstream _2 (pmic@2) one and _4 (pmic@6)?
> >
> > Konrad
> >
> > > + pmm8654au_3_thermal: pm8775-3-thermal {
> > > + polling-delay-passive = <100>;
> > > + polling-delay = <0>;
> > > + thermal-sensors = <&pmm8654au_3_temp_alarm>;
> > > +
> > > + trips {
> > > + trip0 {
> > > + temperature = <105000>;
> > > + hysteresis = <0>;
> > > + type = "passive";
> > > + };
> > > +
> > > + trip1 {
> > > + temperature = <125000>;
> > > + hysteresis = <0>;
> > > + type = "critical";
> > > + };
> > > + };
> > > + };
> > > + };
> > > +};
> > > +
> > > &spmi_bus {
> > > pmm8654au_0: pmic@0 {
> > > compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
> > > @@ -41,6 +85,13 @@ pmm8654au_1: pmic@2 {
> > > reg = <0x2 SPMI_USID>;
> > > #address-cells = <1>;
> > > #size-cells = <0>;
> > > +
> > > + pmm8654au_1_temp_alarm: temp-alarm@a00 {
> > > + compatible = "qcom,spmi-temp-alarm";
> > > + reg = <0xa00>;
> > > + interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> > > + #thermal-sensor-cells = <0>;
> > > + };
> > > };
> > >
> > > pmm8654au_2: pmic@4 {
> > > @@ -55,5 +106,12 @@ pmm8654au_3: pmic@6 {
> > > reg = <0x6 SPMI_USID>;
> > > #address-cells = <1>;
> > > #size-cells = <0>;
> > > +
> > > + pmm8654au_3_temp_alarm: temp-alarm@a00 {
> > > + compatible = "qcom,spmi-temp-alarm";
> > > + reg = <0xa00>;
> > > + interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> > > + #thermal-sensor-cells = <0>;
> > > + };
> > > };
> > > };