[PATCH v3 14/18] arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes

Bartosz Golaszewski
2023-03-27T12:54:05Z

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add GPIO controller nodes to PMICs that have the GPIO hooked up on
sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 40 +++++++++++++++++++++
1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
index be12997a080c..7602cca47bae 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
@@ -125,6 +125,16 @@ pmm8654au_0_pon_resin: resin {
status = "disabled";
};
};
+
+ pmm8654au_0_gpios: gpio@8800 {
+ compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmm8654au_0_gpios 0 0 12>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
};

pmm8654au_1: pmic@2 {
@@ -139,6 +149,16 @@ pmm8654au_1_temp_alarm: temp-alarm@a00 {
interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
#thermal-sensor-cells = <0>;
};
+
+ pmm8654au_1_gpios: gpio@8800 {
+ compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
};

pmm8654au_2: pmic@4 {
@@ -153,6 +173,16 @@ pmm8654au_2_temp_alarm: temp-alarm@a00 {
interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
#thermal-sensor-cells = <0>;
};
+
+ pmm8654au_2_gpios: gpio@8800 {
+ compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
};

pmm8654au_3: pmic@6 {
@@ -167,5 +197,15 @@ pmm8654au_3_temp_alarm: temp-alarm@a00 {
interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
#thermal-sensor-cells = <0>;
};
+
+ pmm8654au_3_gpios: gpio@8800 {
+ compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmm8654au_3_gpios 0 0 12>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
};
};
--
2.37.2