* [net-next PATCH v4 1/5] net: phy: move at803x PHY driver to dedicated directory
2024-01-29 14:15 [net-next PATCH v4 0/5] net: phy: split at803x Christian Marangi
@ 2024-01-29 14:15 ` Christian Marangi
2024-01-29 14:15 ` [net-next PATCH v4 2/5] net: phy: qcom: create and move functions to shared library Christian Marangi
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Christian Marangi @ 2024-01-29 14:15 UTC (permalink / raw)
To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Bjorn Andersson,
Konrad Dybcio, linux-kernel, netdev, linux-arm-msm
Cc: Christian Marangi
In preparation for addition of other Qcom PHY and to tidy things up,
move the at803x PHY driver to dedicated directory.
The same order in the Kconfig selection is saved.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/Kconfig | 7 +------
drivers/net/phy/Makefile | 2 +-
drivers/net/phy/qcom/Kconfig | 7 +++++++
drivers/net/phy/qcom/Makefile | 2 ++
drivers/net/phy/{ => qcom}/at803x.c | 0
5 files changed, 11 insertions(+), 7 deletions(-)
create mode 100644 drivers/net/phy/qcom/Kconfig
create mode 100644 drivers/net/phy/qcom/Makefile
rename drivers/net/phy/{ => qcom}/at803x.c (100%)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 9e2672800f0b..e261e58bf158 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -335,12 +335,7 @@ config NCN26000_PHY
Currently supports the NCN26000 10BASE-T1S Industrial PHY
with MII interface.
-config AT803X_PHY
- tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
- depends on REGULATOR
- help
- Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
- QCA8337(Internal qca8k PHY) model
+source "drivers/net/phy/qcom/Kconfig"
config QSEMI_PHY
tristate "Quality Semiconductor PHYs"
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 6097afd44392..197acfa0b412 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -36,7 +36,6 @@ obj-$(CONFIG_ADIN_PHY) += adin.o
obj-$(CONFIG_ADIN1100_PHY) += adin1100.o
obj-$(CONFIG_AMD_PHY) += amd.o
obj-$(CONFIG_AQUANTIA_PHY) += aquantia/
-obj-$(CONFIG_AT803X_PHY) += at803x.o
ifdef CONFIG_AX88796B_RUST_PHY
obj-$(CONFIG_AX88796B_PHY) += ax88796b_rust.o
else
@@ -91,6 +90,7 @@ endif
obj-$(CONFIG_NXP_C45_TJA11XX_PHY) += nxp-c45-tja.o
obj-$(CONFIG_NXP_CBTX_PHY) += nxp-cbtx.o
obj-$(CONFIG_NXP_TJA11XX_PHY) += nxp-tja11xx.o
+obj-y += qcom/
obj-$(CONFIG_QSEMI_PHY) += qsemi.o
obj-$(CONFIG_REALTEK_PHY) += realtek.o
obj-$(CONFIG_RENESAS_PHY) += uPD60620.o
diff --git a/drivers/net/phy/qcom/Kconfig b/drivers/net/phy/qcom/Kconfig
new file mode 100644
index 000000000000..2c274fbbe410
--- /dev/null
+++ b/drivers/net/phy/qcom/Kconfig
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config AT803X_PHY
+ tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
+ depends on REGULATOR
+ help
+ Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
+ QCA8337(Internal qca8k PHY) model
diff --git a/drivers/net/phy/qcom/Makefile b/drivers/net/phy/qcom/Makefile
new file mode 100644
index 000000000000..6a68da8aaa7b
--- /dev/null
+++ b/drivers/net/phy/qcom/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_AT803X_PHY) += at803x.o
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/qcom/at803x.c
similarity index 100%
rename from drivers/net/phy/at803x.c
rename to drivers/net/phy/qcom/at803x.c
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [net-next PATCH v4 2/5] net: phy: qcom: create and move functions to shared library
2024-01-29 14:15 [net-next PATCH v4 0/5] net: phy: split at803x Christian Marangi
2024-01-29 14:15 ` [net-next PATCH v4 1/5] net: phy: move at803x PHY driver to dedicated directory Christian Marangi
@ 2024-01-29 14:15 ` Christian Marangi
2024-01-29 14:15 ` [net-next PATCH v4 3/5] net: phy: qcom: deatch qca83xx PHY driver from at803x Christian Marangi
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Christian Marangi @ 2024-01-29 14:15 UTC (permalink / raw)
To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Bjorn Andersson,
Konrad Dybcio, linux-kernel, netdev, linux-arm-msm
Cc: Christian Marangi
Create and move functions to shared library in preparation for qca83xx
PHY Family to be detached from at803x driver.
Only the shared defines are moved to the shared qcom.h header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/qcom/Kconfig | 4 ++
drivers/net/phy/qcom/Makefile | 1 +
drivers/net/phy/qcom/at803x.c | 69 +----------------------------
drivers/net/phy/qcom/qcom-phy-lib.c | 53 ++++++++++++++++++++++
drivers/net/phy/qcom/qcom.h | 34 ++++++++++++++
5 files changed, 94 insertions(+), 67 deletions(-)
create mode 100644 drivers/net/phy/qcom/qcom-phy-lib.c
create mode 100644 drivers/net/phy/qcom/qcom.h
diff --git a/drivers/net/phy/qcom/Kconfig b/drivers/net/phy/qcom/Kconfig
index 2c274fbbe410..fe47cc7c94d2 100644
--- a/drivers/net/phy/qcom/Kconfig
+++ b/drivers/net/phy/qcom/Kconfig
@@ -1,6 +1,10 @@
# SPDX-License-Identifier: GPL-2.0-only
+config QCOM_NET_PHYLIB
+ tristate
+
config AT803X_PHY
tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
+ select QCOM_NET_PHYLIB
depends on REGULATOR
help
Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
diff --git a/drivers/net/phy/qcom/Makefile b/drivers/net/phy/qcom/Makefile
index 6a68da8aaa7b..bfba2ed7db27 100644
--- a/drivers/net/phy/qcom/Makefile
+++ b/drivers/net/phy/qcom/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_QCOM_NET_PHYLIB) += qcom-phy-lib.o
obj-$(CONFIG_AT803X_PHY) += at803x.o
diff --git a/drivers/net/phy/qcom/at803x.c b/drivers/net/phy/qcom/at803x.c
index 9c07a6cc6e67..8194618c0865 100644
--- a/drivers/net/phy/qcom/at803x.c
+++ b/drivers/net/phy/qcom/at803x.c
@@ -22,6 +22,8 @@
#include <linux/sfp.h>
#include <dt-bindings/net/qca-ar803x.h>
+#include "qcom.h"
+
#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10
#define AT803X_SFC_ASSERT_CRS BIT(11)
#define AT803X_SFC_FORCE_LINK BIT(10)
@@ -84,9 +86,6 @@
#define AT803X_REG_CHIP_CONFIG 0x1f
#define AT803X_BT_BX_REG_SEL 0x8000
-#define AT803X_DEBUG_ADDR 0x1D
-#define AT803X_DEBUG_DATA 0x1E
-
#define AT803X_MODE_CFG_MASK 0x0F
#define AT803X_MODE_CFG_BASET_RGMII 0x00
#define AT803X_MODE_CFG_BASET_SGMII 0x01
@@ -103,19 +102,6 @@
#define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/
#define AT803X_PSSR_MR_AN_COMPLETE 0x0200
-#define AT803X_DEBUG_ANALOG_TEST_CTRL 0x00
-#define QCA8327_DEBUG_MANU_CTRL_EN BIT(2)
-#define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2)
-#define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15)
-
-#define AT803X_DEBUG_SYSTEM_CTRL_MODE 0x05
-#define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8)
-
-#define AT803X_DEBUG_REG_HIB_CTRL 0x0b
-#define AT803X_DEBUG_HIB_CTRL_SEL_RST_80U BIT(10)
-#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13)
-#define AT803X_DEBUG_HIB_CTRL_PS_HIB_EN BIT(15)
-
#define AT803X_DEBUG_REG_3C 0x3C
#define AT803X_DEBUG_REG_GREEN 0x3D
@@ -393,18 +379,6 @@ MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
MODULE_AUTHOR("Matus Ujhelyi");
MODULE_LICENSE("GPL");
-enum stat_access_type {
- PHY,
- MMD
-};
-
-struct at803x_hw_stat {
- const char *string;
- u8 reg;
- u32 mask;
- enum stat_access_type access_type;
-};
-
static struct at803x_hw_stat qca83xx_hw_stats[] = {
{ "phy_idle_errors", 0xa, GENMASK(7, 0), PHY},
{ "phy_receive_errors", 0x15, GENMASK(15, 0), PHY},
@@ -439,45 +413,6 @@ struct at803x_context {
u16 led_control;
};
-static int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data)
-{
- int ret;
-
- ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
- if (ret < 0)
- return ret;
-
- return phy_write(phydev, AT803X_DEBUG_DATA, data);
-}
-
-static int at803x_debug_reg_read(struct phy_device *phydev, u16 reg)
-{
- int ret;
-
- ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
- if (ret < 0)
- return ret;
-
- return phy_read(phydev, AT803X_DEBUG_DATA);
-}
-
-static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
- u16 clear, u16 set)
-{
- u16 val;
- int ret;
-
- ret = at803x_debug_reg_read(phydev, reg);
- if (ret < 0)
- return ret;
-
- val = ret & 0xffff;
- val &= ~clear;
- val |= set;
-
- return phy_write(phydev, AT803X_DEBUG_DATA, val);
-}
-
static int at803x_write_page(struct phy_device *phydev, int page)
{
int mask;
diff --git a/drivers/net/phy/qcom/qcom-phy-lib.c b/drivers/net/phy/qcom/qcom-phy-lib.c
new file mode 100644
index 000000000000..7192184429b7
--- /dev/null
+++ b/drivers/net/phy/qcom/qcom-phy-lib.c
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/phy.h>
+#include <linux/module.h>
+
+#include "qcom.h"
+
+MODULE_DESCRIPTION("Qualcomm PHY driver Common Functions");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_LICENSE("GPL");
+
+int at803x_debug_reg_read(struct phy_device *phydev, u16 reg)
+{
+ int ret;
+
+ ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
+ if (ret < 0)
+ return ret;
+
+ return phy_read(phydev, AT803X_DEBUG_DATA);
+}
+EXPORT_SYMBOL_GPL(at803x_debug_reg_read);
+
+int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
+ u16 clear, u16 set)
+{
+ u16 val;
+ int ret;
+
+ ret = at803x_debug_reg_read(phydev, reg);
+ if (ret < 0)
+ return ret;
+
+ val = ret & 0xffff;
+ val &= ~clear;
+ val |= set;
+
+ return phy_write(phydev, AT803X_DEBUG_DATA, val);
+}
+EXPORT_SYMBOL_GPL(at803x_debug_reg_mask);
+
+int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data)
+{
+ int ret;
+
+ ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
+ if (ret < 0)
+ return ret;
+
+ return phy_write(phydev, AT803X_DEBUG_DATA, data);
+}
+EXPORT_SYMBOL_GPL(at803x_debug_reg_write);
diff --git a/drivers/net/phy/qcom/qcom.h b/drivers/net/phy/qcom/qcom.h
new file mode 100644
index 000000000000..8eb476d7c282
--- /dev/null
+++ b/drivers/net/phy/qcom/qcom.h
@@ -0,0 +1,34 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#define AT803X_DEBUG_ADDR 0x1D
+#define AT803X_DEBUG_DATA 0x1E
+
+#define AT803X_DEBUG_ANALOG_TEST_CTRL 0x00
+#define QCA8327_DEBUG_MANU_CTRL_EN BIT(2)
+#define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2)
+#define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15)
+
+#define AT803X_DEBUG_SYSTEM_CTRL_MODE 0x05
+#define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8)
+
+#define AT803X_DEBUG_REG_HIB_CTRL 0x0b
+#define AT803X_DEBUG_HIB_CTRL_SEL_RST_80U BIT(10)
+#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13)
+#define AT803X_DEBUG_HIB_CTRL_PS_HIB_EN BIT(15)
+
+enum stat_access_type {
+ PHY,
+ MMD
+};
+
+struct at803x_hw_stat {
+ const char *string;
+ u8 reg;
+ u32 mask;
+ enum stat_access_type access_type;
+};
+
+int at803x_debug_reg_read(struct phy_device *phydev, u16 reg);
+int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
+ u16 clear, u16 set);
+int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data);
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [net-next PATCH v4 3/5] net: phy: qcom: deatch qca83xx PHY driver from at803x
2024-01-29 14:15 [net-next PATCH v4 0/5] net: phy: split at803x Christian Marangi
2024-01-29 14:15 ` [net-next PATCH v4 1/5] net: phy: move at803x PHY driver to dedicated directory Christian Marangi
2024-01-29 14:15 ` [net-next PATCH v4 2/5] net: phy: qcom: create and move functions to shared library Christian Marangi
@ 2024-01-29 14:15 ` Christian Marangi
2024-01-29 14:15 ` [net-next PATCH v4 4/5] net: phy: qcom: move additional functions to shared library Christian Marangi
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Christian Marangi @ 2024-01-29 14:15 UTC (permalink / raw)
To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Bjorn Andersson,
Konrad Dybcio, linux-kernel, netdev, linux-arm-msm
Cc: Christian Marangi
Deatch qca83xx PHY driver from at803x.
The QCA83xx PHYs implement specific function and doesn't use generic
at803x so it can be detached from the driver and moved to a dedicated
one.
Probe function and priv struct is reimplemented to allocate and use
only the qca83xx specific data. Unused data from at803x PHY driver
are dropped from at803x priv struct.
This is to make slimmer PHY drivers instead of including lots of bloat
that would never be used in specific SoC.
A new Kconfig flag QCA83XX_PHY is introduced to compile the new
introduced PHY driver.
As the Kconfig name starts with Qualcomm the same order is kept.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/qcom/Kconfig | 11 +-
drivers/net/phy/qcom/Makefile | 1 +
drivers/net/phy/qcom/at803x.c | 235 ----------------------------
drivers/net/phy/qcom/qca83xx.c | 275 +++++++++++++++++++++++++++++++++
4 files changed, 284 insertions(+), 238 deletions(-)
create mode 100644 drivers/net/phy/qcom/qca83xx.c
diff --git a/drivers/net/phy/qcom/Kconfig b/drivers/net/phy/qcom/Kconfig
index fe47cc7c94d2..ba78bbe31857 100644
--- a/drivers/net/phy/qcom/Kconfig
+++ b/drivers/net/phy/qcom/Kconfig
@@ -3,9 +3,14 @@ config QCOM_NET_PHYLIB
tristate
config AT803X_PHY
- tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
+ tristate "Qualcomm Atheros AR803X PHYs"
select QCOM_NET_PHYLIB
depends on REGULATOR
help
- Currently supports the AR8030, AR8031, AR8033, AR8035 and internal
- QCA8337(Internal qca8k PHY) model
+ Currently supports the AR8030, AR8031, AR8033, AR8035 model
+
+config QCA83XX_PHY
+ tristate "Qualcomm Atheros QCA833x PHYs"
+ select QCOM_NET_PHYLIB
+ help
+ Currently supports the internal QCA8337(Internal qca8k PHY) model
diff --git a/drivers/net/phy/qcom/Makefile b/drivers/net/phy/qcom/Makefile
index bfba2ed7db27..3d98e397e063 100644
--- a/drivers/net/phy/qcom/Makefile
+++ b/drivers/net/phy/qcom/Makefile
@@ -1,3 +1,4 @@
# SPDX-License-Identifier: GPL-2.0
obj-$(CONFIG_QCOM_NET_PHYLIB) += qcom-phy-lib.o
obj-$(CONFIG_AT803X_PHY) += at803x.o
+obj-$(CONFIG_QCA83XX_PHY) += qca83xx.o
diff --git a/drivers/net/phy/qcom/at803x.c b/drivers/net/phy/qcom/at803x.c
index 8194618c0865..638babc50df1 100644
--- a/drivers/net/phy/qcom/at803x.c
+++ b/drivers/net/phy/qcom/at803x.c
@@ -102,17 +102,10 @@
#define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/
#define AT803X_PSSR_MR_AN_COMPLETE 0x0200
-#define AT803X_DEBUG_REG_3C 0x3C
-
-#define AT803X_DEBUG_REG_GREEN 0x3D
-#define AT803X_DEBUG_GATE_CLK_IN1000 BIT(6)
-
#define AT803X_DEBUG_REG_1F 0x1F
#define AT803X_DEBUG_PLL_ON BIT(2)
#define AT803X_DEBUG_RGMII_1V8 BIT(3)
-#define MDIO_AZ_DEBUG 0x800D
-
/* AT803x supports either the XTAL input pad, an internal PLL or the
* DSP as clock reference for the clock output pad. The XTAL reference
* is only used for 25 MHz output, all other frequencies need the PLL.
@@ -163,13 +156,7 @@
#define QCA8081_PHY_ID 0x004dd101
-#define QCA8327_A_PHY_ID 0x004dd033
-#define QCA8327_B_PHY_ID 0x004dd034
-#define QCA8337_PHY_ID 0x004dd036
#define QCA9561_PHY_ID 0x004dd042
-#define QCA8K_PHY_ID_MASK 0xffffffff
-
-#define QCA8K_DEVFLAGS_REVISION_MASK GENMASK(2, 0)
#define AT803X_PAGE_FIBER 0
#define AT803X_PAGE_COPPER 1
@@ -379,12 +366,6 @@ MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
MODULE_AUTHOR("Matus Ujhelyi");
MODULE_LICENSE("GPL");
-static struct at803x_hw_stat qca83xx_hw_stats[] = {
- { "phy_idle_errors", 0xa, GENMASK(7, 0), PHY},
- { "phy_receive_errors", 0x15, GENMASK(15, 0), PHY},
- { "eee_wake_errors", 0x16, GENMASK(15, 0), MMD},
-};
-
struct at803x_ss_mask {
u16 speed_mask;
u8 speed_shift;
@@ -400,7 +381,6 @@ struct at803x_priv {
bool is_1000basex;
struct regulator_dev *vddio_rdev;
struct regulator_dev *vddh_rdev;
- u64 stats[ARRAY_SIZE(qca83xx_hw_stats)];
int led_polarity_mode;
};
@@ -564,53 +544,6 @@ static void at803x_get_wol(struct phy_device *phydev,
wol->wolopts |= WAKE_MAGIC;
}
-static int qca83xx_get_sset_count(struct phy_device *phydev)
-{
- return ARRAY_SIZE(qca83xx_hw_stats);
-}
-
-static void qca83xx_get_strings(struct phy_device *phydev, u8 *data)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++) {
- strscpy(data + i * ETH_GSTRING_LEN,
- qca83xx_hw_stats[i].string, ETH_GSTRING_LEN);
- }
-}
-
-static u64 qca83xx_get_stat(struct phy_device *phydev, int i)
-{
- struct at803x_hw_stat stat = qca83xx_hw_stats[i];
- struct at803x_priv *priv = phydev->priv;
- int val;
- u64 ret;
-
- if (stat.access_type == MMD)
- val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg);
- else
- val = phy_read(phydev, stat.reg);
-
- if (val < 0) {
- ret = U64_MAX;
- } else {
- val = val & stat.mask;
- priv->stats[i] += val;
- ret = priv->stats[i];
- }
-
- return ret;
-}
-
-static void qca83xx_get_stats(struct phy_device *phydev,
- struct ethtool_stats *stats, u64 *data)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++)
- data[i] = qca83xx_get_stat(phydev, i);
-}
-
static int at803x_suspend(struct phy_device *phydev)
{
int value;
@@ -1707,124 +1640,6 @@ static int at8035_probe(struct phy_device *phydev)
return at8035_parse_dt(phydev);
}
-static int qca83xx_config_init(struct phy_device *phydev)
-{
- u8 switch_revision;
-
- switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK;
-
- switch (switch_revision) {
- case 1:
- /* For 100M waveform */
- at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea);
- /* Turn on Gigabit clock */
- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0);
- break;
-
- case 2:
- phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0);
- fallthrough;
- case 4:
- phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f);
- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860);
- at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46);
- at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000);
- break;
- }
-
- /* Following original QCA sourcecode set port to prefer master */
- phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER);
-
- return 0;
-}
-
-static int qca8327_config_init(struct phy_device *phydev)
-{
- /* QCA8327 require DAC amplitude adjustment for 100m set to +6%.
- * Disable on init and enable only with 100m speed following
- * qca original source code.
- */
- at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
- QCA8327_DEBUG_MANU_CTRL_EN, 0);
-
- return qca83xx_config_init(phydev);
-}
-
-static void qca83xx_link_change_notify(struct phy_device *phydev)
-{
- /* Set DAC Amplitude adjustment to +6% for 100m on link running */
- if (phydev->state == PHY_RUNNING) {
- if (phydev->speed == SPEED_100)
- at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
- QCA8327_DEBUG_MANU_CTRL_EN,
- QCA8327_DEBUG_MANU_CTRL_EN);
- } else {
- /* Reset DAC Amplitude adjustment */
- at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
- QCA8327_DEBUG_MANU_CTRL_EN, 0);
- }
-}
-
-static int qca83xx_resume(struct phy_device *phydev)
-{
- int ret, val;
-
- /* Skip reset if not suspended */
- if (!phydev->suspended)
- return 0;
-
- /* Reinit the port, reset values set by suspend */
- qca83xx_config_init(phydev);
-
- /* Reset the port on port resume */
- phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE);
-
- /* On resume from suspend the switch execute a reset and
- * restart auto-negotiation. Wait for reset to complete.
- */
- ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET),
- 50000, 600000, true);
- if (ret)
- return ret;
-
- usleep_range(1000, 2000);
-
- return 0;
-}
-
-static int qca83xx_suspend(struct phy_device *phydev)
-{
- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN,
- AT803X_DEBUG_GATE_CLK_IN1000, 0);
-
- at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
- AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE |
- AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0);
-
- return 0;
-}
-
-static int qca8337_suspend(struct phy_device *phydev)
-{
- /* Only QCA8337 support actual suspend. */
- genphy_suspend(phydev);
-
- return qca83xx_suspend(phydev);
-}
-
-static int qca8327_suspend(struct phy_device *phydev)
-{
- u16 mask = 0;
-
- /* QCA8327 cause port unreliability when phy suspend
- * is set.
- */
- mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX);
- phy_modify(phydev, MII_BMCR, mask, 0);
-
- return qca83xx_suspend(phydev);
-}
-
static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
{
int ret;
@@ -2598,53 +2413,6 @@ static struct phy_driver at803x_driver[] = {
.read_status = at803x_read_status,
.soft_reset = genphy_soft_reset,
.config_aneg = at803x_config_aneg,
-}, {
- /* QCA8337 */
- .phy_id = QCA8337_PHY_ID,
- .phy_id_mask = QCA8K_PHY_ID_MASK,
- .name = "Qualcomm Atheros 8337 internal PHY",
- /* PHY_GBIT_FEATURES */
- .probe = at803x_probe,
- .flags = PHY_IS_INTERNAL,
- .config_init = qca83xx_config_init,
- .soft_reset = genphy_soft_reset,
- .get_sset_count = qca83xx_get_sset_count,
- .get_strings = qca83xx_get_strings,
- .get_stats = qca83xx_get_stats,
- .suspend = qca8337_suspend,
- .resume = qca83xx_resume,
-}, {
- /* QCA8327-A from switch QCA8327-AL1A */
- .phy_id = QCA8327_A_PHY_ID,
- .phy_id_mask = QCA8K_PHY_ID_MASK,
- .name = "Qualcomm Atheros 8327-A internal PHY",
- /* PHY_GBIT_FEATURES */
- .link_change_notify = qca83xx_link_change_notify,
- .probe = at803x_probe,
- .flags = PHY_IS_INTERNAL,
- .config_init = qca8327_config_init,
- .soft_reset = genphy_soft_reset,
- .get_sset_count = qca83xx_get_sset_count,
- .get_strings = qca83xx_get_strings,
- .get_stats = qca83xx_get_stats,
- .suspend = qca8327_suspend,
- .resume = qca83xx_resume,
-}, {
- /* QCA8327-B from switch QCA8327-BL1A */
- .phy_id = QCA8327_B_PHY_ID,
- .phy_id_mask = QCA8K_PHY_ID_MASK,
- .name = "Qualcomm Atheros 8327-B internal PHY",
- /* PHY_GBIT_FEATURES */
- .link_change_notify = qca83xx_link_change_notify,
- .probe = at803x_probe,
- .flags = PHY_IS_INTERNAL,
- .config_init = qca8327_config_init,
- .soft_reset = genphy_soft_reset,
- .get_sset_count = qca83xx_get_sset_count,
- .get_strings = qca83xx_get_strings,
- .get_stats = qca83xx_get_stats,
- .suspend = qca8327_suspend,
- .resume = qca83xx_resume,
}, {
/* Qualcomm QCA8081 */
PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
@@ -2683,9 +2451,6 @@ static struct mdio_device_id __maybe_unused atheros_tbl[] = {
{ PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) },
{ PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) },
{ PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) },
- { PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) },
- { PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) },
- { PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) },
{ PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) },
{ PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
{ }
diff --git a/drivers/net/phy/qcom/qca83xx.c b/drivers/net/phy/qcom/qca83xx.c
new file mode 100644
index 000000000000..5d083ef0250e
--- /dev/null
+++ b/drivers/net/phy/qcom/qca83xx.c
@@ -0,0 +1,275 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/phy.h>
+#include <linux/module.h>
+
+#include "qcom.h"
+
+#define AT803X_DEBUG_REG_3C 0x3C
+
+#define AT803X_DEBUG_REG_GREEN 0x3D
+#define AT803X_DEBUG_GATE_CLK_IN1000 BIT(6)
+
+#define MDIO_AZ_DEBUG 0x800D
+
+#define QCA8327_A_PHY_ID 0x004dd033
+#define QCA8327_B_PHY_ID 0x004dd034
+#define QCA8337_PHY_ID 0x004dd036
+#define QCA8K_PHY_ID_MASK 0xffffffff
+
+#define QCA8K_DEVFLAGS_REVISION_MASK GENMASK(2, 0)
+
+static struct at803x_hw_stat qca83xx_hw_stats[] = {
+ { "phy_idle_errors", 0xa, GENMASK(7, 0), PHY},
+ { "phy_receive_errors", 0x15, GENMASK(15, 0), PHY},
+ { "eee_wake_errors", 0x16, GENMASK(15, 0), MMD},
+};
+
+struct qca83xx_priv {
+ u64 stats[ARRAY_SIZE(qca83xx_hw_stats)];
+};
+
+MODULE_DESCRIPTION("Qualcomm Atheros QCA83XX PHY driver");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_LICENSE("GPL");
+
+static int qca83xx_get_sset_count(struct phy_device *phydev)
+{
+ return ARRAY_SIZE(qca83xx_hw_stats);
+}
+
+static void qca83xx_get_strings(struct phy_device *phydev, u8 *data)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++) {
+ strscpy(data + i * ETH_GSTRING_LEN,
+ qca83xx_hw_stats[i].string, ETH_GSTRING_LEN);
+ }
+}
+
+static u64 qca83xx_get_stat(struct phy_device *phydev, int i)
+{
+ struct at803x_hw_stat stat = qca83xx_hw_stats[i];
+ struct qca83xx_priv *priv = phydev->priv;
+ int val;
+ u64 ret;
+
+ if (stat.access_type == MMD)
+ val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg);
+ else
+ val = phy_read(phydev, stat.reg);
+
+ if (val < 0) {
+ ret = U64_MAX;
+ } else {
+ val = val & stat.mask;
+ priv->stats[i] += val;
+ ret = priv->stats[i];
+ }
+
+ return ret;
+}
+
+static void qca83xx_get_stats(struct phy_device *phydev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++)
+ data[i] = qca83xx_get_stat(phydev, i);
+}
+
+static int qca83xx_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct qca83xx_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ phydev->priv = priv;
+
+ return 0;
+}
+
+static int qca83xx_config_init(struct phy_device *phydev)
+{
+ u8 switch_revision;
+
+ switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK;
+
+ switch (switch_revision) {
+ case 1:
+ /* For 100M waveform */
+ at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea);
+ /* Turn on Gigabit clock */
+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0);
+ break;
+
+ case 2:
+ phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0);
+ fallthrough;
+ case 4:
+ phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f);
+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860);
+ at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46);
+ at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000);
+ break;
+ }
+
+ /* Following original QCA sourcecode set port to prefer master */
+ phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER);
+
+ return 0;
+}
+
+static int qca8327_config_init(struct phy_device *phydev)
+{
+ /* QCA8327 require DAC amplitude adjustment for 100m set to +6%.
+ * Disable on init and enable only with 100m speed following
+ * qca original source code.
+ */
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+ QCA8327_DEBUG_MANU_CTRL_EN, 0);
+
+ return qca83xx_config_init(phydev);
+}
+
+static void qca83xx_link_change_notify(struct phy_device *phydev)
+{
+ /* Set DAC Amplitude adjustment to +6% for 100m on link running */
+ if (phydev->state == PHY_RUNNING) {
+ if (phydev->speed == SPEED_100)
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+ QCA8327_DEBUG_MANU_CTRL_EN,
+ QCA8327_DEBUG_MANU_CTRL_EN);
+ } else {
+ /* Reset DAC Amplitude adjustment */
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+ QCA8327_DEBUG_MANU_CTRL_EN, 0);
+ }
+}
+
+static int qca83xx_resume(struct phy_device *phydev)
+{
+ int ret, val;
+
+ /* Skip reset if not suspended */
+ if (!phydev->suspended)
+ return 0;
+
+ /* Reinit the port, reset values set by suspend */
+ qca83xx_config_init(phydev);
+
+ /* Reset the port on port resume */
+ phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE);
+
+ /* On resume from suspend the switch execute a reset and
+ * restart auto-negotiation. Wait for reset to complete.
+ */
+ ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET),
+ 50000, 600000, true);
+ if (ret)
+ return ret;
+
+ usleep_range(1000, 2000);
+
+ return 0;
+}
+
+static int qca83xx_suspend(struct phy_device *phydev)
+{
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN,
+ AT803X_DEBUG_GATE_CLK_IN1000, 0);
+
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
+ AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE |
+ AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0);
+
+ return 0;
+}
+
+static int qca8337_suspend(struct phy_device *phydev)
+{
+ /* Only QCA8337 support actual suspend. */
+ genphy_suspend(phydev);
+
+ return qca83xx_suspend(phydev);
+}
+
+static int qca8327_suspend(struct phy_device *phydev)
+{
+ u16 mask = 0;
+
+ /* QCA8327 cause port unreliability when phy suspend
+ * is set.
+ */
+ mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX);
+ phy_modify(phydev, MII_BMCR, mask, 0);
+
+ return qca83xx_suspend(phydev);
+}
+
+static struct phy_driver qca83xx_driver[] = {
+{
+ /* QCA8337 */
+ .phy_id = QCA8337_PHY_ID,
+ .phy_id_mask = QCA8K_PHY_ID_MASK,
+ .name = "Qualcomm Atheros 8337 internal PHY",
+ /* PHY_GBIT_FEATURES */
+ .probe = qca83xx_probe,
+ .flags = PHY_IS_INTERNAL,
+ .config_init = qca83xx_config_init,
+ .soft_reset = genphy_soft_reset,
+ .get_sset_count = qca83xx_get_sset_count,
+ .get_strings = qca83xx_get_strings,
+ .get_stats = qca83xx_get_stats,
+ .suspend = qca8337_suspend,
+ .resume = qca83xx_resume,
+}, {
+ /* QCA8327-A from switch QCA8327-AL1A */
+ .phy_id = QCA8327_A_PHY_ID,
+ .phy_id_mask = QCA8K_PHY_ID_MASK,
+ .name = "Qualcomm Atheros 8327-A internal PHY",
+ /* PHY_GBIT_FEATURES */
+ .link_change_notify = qca83xx_link_change_notify,
+ .probe = qca83xx_probe,
+ .flags = PHY_IS_INTERNAL,
+ .config_init = qca8327_config_init,
+ .soft_reset = genphy_soft_reset,
+ .get_sset_count = qca83xx_get_sset_count,
+ .get_strings = qca83xx_get_strings,
+ .get_stats = qca83xx_get_stats,
+ .suspend = qca8327_suspend,
+ .resume = qca83xx_resume,
+}, {
+ /* QCA8327-B from switch QCA8327-BL1A */
+ .phy_id = QCA8327_B_PHY_ID,
+ .phy_id_mask = QCA8K_PHY_ID_MASK,
+ .name = "Qualcomm Atheros 8327-B internal PHY",
+ /* PHY_GBIT_FEATURES */
+ .link_change_notify = qca83xx_link_change_notify,
+ .probe = qca83xx_probe,
+ .flags = PHY_IS_INTERNAL,
+ .config_init = qca8327_config_init,
+ .soft_reset = genphy_soft_reset,
+ .get_sset_count = qca83xx_get_sset_count,
+ .get_strings = qca83xx_get_strings,
+ .get_stats = qca83xx_get_stats,
+ .suspend = qca8327_suspend,
+ .resume = qca83xx_resume,
+}, };
+
+module_phy_driver(qca83xx_driver);
+
+static struct mdio_device_id __maybe_unused qca83xx_tbl[] = {
+ { PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) },
+ { PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) },
+ { PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, qca83xx_tbl);
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [net-next PATCH v4 4/5] net: phy: qcom: move additional functions to shared library
2024-01-29 14:15 [net-next PATCH v4 0/5] net: phy: split at803x Christian Marangi
` (2 preceding siblings ...)
2024-01-29 14:15 ` [net-next PATCH v4 3/5] net: phy: qcom: deatch qca83xx PHY driver from at803x Christian Marangi
@ 2024-01-29 14:15 ` Christian Marangi
2024-01-29 14:15 ` [net-next PATCH v4 5/5] net: phy: qcom: detach qca808x PHY driver from at803x Christian Marangi
2024-02-01 0:40 ` [net-next PATCH v4 0/5] net: phy: split at803x patchwork-bot+netdevbpf
5 siblings, 0 replies; 7+ messages in thread
From: Christian Marangi @ 2024-01-29 14:15 UTC (permalink / raw)
To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Bjorn Andersson,
Konrad Dybcio, linux-kernel, netdev, linux-arm-msm
Cc: Christian Marangi
Move additional functions to shared library in preparation for qca808x
PHY Family to be detached from at803x driver.
Only the shared defines are moved to the shared qcom.h header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/qcom/at803x.c | 426 +---------------------------
drivers/net/phy/qcom/qcom-phy-lib.c | 376 ++++++++++++++++++++++++
drivers/net/phy/qcom/qcom.h | 86 ++++++
3 files changed, 463 insertions(+), 425 deletions(-)
diff --git a/drivers/net/phy/qcom/at803x.c b/drivers/net/phy/qcom/at803x.c
index 638babc50df1..6a753498b994 100644
--- a/drivers/net/phy/qcom/at803x.c
+++ b/drivers/net/phy/qcom/at803x.c
@@ -24,65 +24,11 @@
#include "qcom.h"
-#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10
-#define AT803X_SFC_ASSERT_CRS BIT(11)
-#define AT803X_SFC_FORCE_LINK BIT(10)
-#define AT803X_SFC_MDI_CROSSOVER_MODE_M GENMASK(6, 5)
-#define AT803X_SFC_AUTOMATIC_CROSSOVER 0x3
-#define AT803X_SFC_MANUAL_MDIX 0x1
-#define AT803X_SFC_MANUAL_MDI 0x0
-#define AT803X_SFC_SQE_TEST BIT(2)
-#define AT803X_SFC_POLARITY_REVERSAL BIT(1)
-#define AT803X_SFC_DISABLE_JABBER BIT(0)
-
-#define AT803X_SPECIFIC_STATUS 0x11
-#define AT803X_SS_SPEED_MASK GENMASK(15, 14)
-#define AT803X_SS_SPEED_1000 2
-#define AT803X_SS_SPEED_100 1
-#define AT803X_SS_SPEED_10 0
-#define AT803X_SS_DUPLEX BIT(13)
-#define AT803X_SS_SPEED_DUPLEX_RESOLVED BIT(11)
-#define AT803X_SS_MDIX BIT(6)
-
-#define QCA808X_SS_SPEED_MASK GENMASK(9, 7)
-#define QCA808X_SS_SPEED_2500 4
-
-#define AT803X_INTR_ENABLE 0x12
-#define AT803X_INTR_ENABLE_AUTONEG_ERR BIT(15)
-#define AT803X_INTR_ENABLE_SPEED_CHANGED BIT(14)
-#define AT803X_INTR_ENABLE_DUPLEX_CHANGED BIT(13)
-#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
-#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
-#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
-#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
-#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
-#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
-#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
-#define AT803X_INTR_ENABLE_WOL BIT(0)
-
-#define AT803X_INTR_STATUS 0x13
-
-#define AT803X_SMART_SPEED 0x14
-#define AT803X_SMART_SPEED_ENABLE BIT(5)
-#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK GENMASK(4, 2)
-#define AT803X_SMART_SPEED_BYPASS_TIMER BIT(1)
-#define AT803X_CDT 0x16
-#define AT803X_CDT_MDI_PAIR_MASK GENMASK(9, 8)
-#define AT803X_CDT_ENABLE_TEST BIT(0)
-#define AT803X_CDT_STATUS 0x1c
-#define AT803X_CDT_STATUS_STAT_NORMAL 0
-#define AT803X_CDT_STATUS_STAT_SHORT 1
-#define AT803X_CDT_STATUS_STAT_OPEN 2
-#define AT803X_CDT_STATUS_STAT_FAIL 3
-#define AT803X_CDT_STATUS_STAT_MASK GENMASK(9, 8)
-#define AT803X_CDT_STATUS_DELTA_TIME_MASK GENMASK(7, 0)
#define AT803X_LED_CONTROL 0x18
#define AT803X_PHY_MMD3_WOL_CTRL 0x8012
#define AT803X_WOL_EN BIT(5)
-#define AT803X_LOC_MAC_ADDR_0_15_OFFSET 0x804C
-#define AT803X_LOC_MAC_ADDR_16_31_OFFSET 0x804B
-#define AT803X_LOC_MAC_ADDR_32_47_OFFSET 0x804A
+
#define AT803X_REG_CHIP_CONFIG 0x1f
#define AT803X_BT_BX_REG_SEL 0x8000
@@ -138,10 +84,6 @@
#define AT803X_CLK_OUT_STRENGTH_HALF 1
#define AT803X_CLK_OUT_STRENGTH_QUARTER 2
-#define AT803X_DEFAULT_DOWNSHIFT 5
-#define AT803X_MIN_DOWNSHIFT 2
-#define AT803X_MAX_DOWNSHIFT 9
-
#define AT803X_MMD3_SMARTEEE_CTL1 0x805b
#define AT803X_MMD3_SMARTEEE_CTL2 0x805c
#define AT803X_MMD3_SMARTEEE_CTL3 0x805d
@@ -366,11 +308,6 @@ MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
MODULE_AUTHOR("Matus Ujhelyi");
MODULE_LICENSE("GPL");
-struct at803x_ss_mask {
- u16 speed_mask;
- u8 speed_shift;
-};
-
struct at803x_priv {
int flags;
u16 clk_25m_reg;
@@ -470,80 +407,6 @@ static void at803x_context_restore(struct phy_device *phydev,
phy_write(phydev, AT803X_LED_CONTROL, context->led_control);
}
-static int at803x_set_wol(struct phy_device *phydev,
- struct ethtool_wolinfo *wol)
-{
- int ret, irq_enabled;
-
- if (wol->wolopts & WAKE_MAGIC) {
- struct net_device *ndev = phydev->attached_dev;
- const u8 *mac;
- unsigned int i;
- static const unsigned int offsets[] = {
- AT803X_LOC_MAC_ADDR_32_47_OFFSET,
- AT803X_LOC_MAC_ADDR_16_31_OFFSET,
- AT803X_LOC_MAC_ADDR_0_15_OFFSET,
- };
-
- if (!ndev)
- return -ENODEV;
-
- mac = (const u8 *)ndev->dev_addr;
-
- if (!is_valid_ether_addr(mac))
- return -EINVAL;
-
- for (i = 0; i < 3; i++)
- phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
- mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
-
- /* Enable WOL interrupt */
- ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
- if (ret)
- return ret;
- } else {
- /* Disable WOL interrupt */
- ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
- if (ret)
- return ret;
- }
-
- /* Clear WOL status */
- ret = phy_read(phydev, AT803X_INTR_STATUS);
- if (ret < 0)
- return ret;
-
- /* Check if there are other interrupts except for WOL triggered when PHY is
- * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can
- * be passed up to the interrupt PIN.
- */
- irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
- if (irq_enabled < 0)
- return irq_enabled;
-
- irq_enabled &= ~AT803X_INTR_ENABLE_WOL;
- if (ret & irq_enabled && !phy_polling_mode(phydev))
- phy_trigger_machine(phydev);
-
- return 0;
-}
-
-static void at803x_get_wol(struct phy_device *phydev,
- struct ethtool_wolinfo *wol)
-{
- int value;
-
- wol->supported = WAKE_MAGIC;
- wol->wolopts = 0;
-
- value = phy_read(phydev, AT803X_INTR_ENABLE);
- if (value < 0)
- return;
-
- if (value & AT803X_INTR_ENABLE_WOL)
- wol->wolopts |= WAKE_MAGIC;
-}
-
static int at803x_suspend(struct phy_device *phydev)
{
int value;
@@ -816,73 +679,6 @@ static int at803x_config_init(struct phy_device *phydev)
return phy_modify(phydev, MII_ADVERTISE, MDIO_AN_CTRL1_XNP, 0);
}
-static int at803x_ack_interrupt(struct phy_device *phydev)
-{
- int err;
-
- err = phy_read(phydev, AT803X_INTR_STATUS);
-
- return (err < 0) ? err : 0;
-}
-
-static int at803x_config_intr(struct phy_device *phydev)
-{
- int err;
- int value;
-
- value = phy_read(phydev, AT803X_INTR_ENABLE);
-
- if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
- /* Clear any pending interrupts */
- err = at803x_ack_interrupt(phydev);
- if (err)
- return err;
-
- value |= AT803X_INTR_ENABLE_AUTONEG_ERR;
- value |= AT803X_INTR_ENABLE_SPEED_CHANGED;
- value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
- value |= AT803X_INTR_ENABLE_LINK_FAIL;
- value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
-
- err = phy_write(phydev, AT803X_INTR_ENABLE, value);
- } else {
- err = phy_write(phydev, AT803X_INTR_ENABLE, 0);
- if (err)
- return err;
-
- /* Clear any pending interrupts */
- err = at803x_ack_interrupt(phydev);
- }
-
- return err;
-}
-
-static irqreturn_t at803x_handle_interrupt(struct phy_device *phydev)
-{
- int irq_status, int_enabled;
-
- irq_status = phy_read(phydev, AT803X_INTR_STATUS);
- if (irq_status < 0) {
- phy_error(phydev);
- return IRQ_NONE;
- }
-
- /* Read the current enabled interrupts */
- int_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
- if (int_enabled < 0) {
- phy_error(phydev);
- return IRQ_NONE;
- }
-
- /* See if this was one of our enabled interrupts */
- if (!(irq_status & int_enabled))
- return IRQ_NONE;
-
- phy_trigger_machine(phydev);
-
- return IRQ_HANDLED;
-}
-
static void at803x_link_change_notify(struct phy_device *phydev)
{
/*
@@ -908,69 +704,6 @@ static void at803x_link_change_notify(struct phy_device *phydev)
}
}
-static int at803x_read_specific_status(struct phy_device *phydev,
- struct at803x_ss_mask ss_mask)
-{
- int ss;
-
- /* Read the AT8035 PHY-Specific Status register, which indicates the
- * speed and duplex that the PHY is actually using, irrespective of
- * whether we are in autoneg mode or not.
- */
- ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
- if (ss < 0)
- return ss;
-
- if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
- int sfc, speed;
-
- sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL);
- if (sfc < 0)
- return sfc;
-
- speed = ss & ss_mask.speed_mask;
- speed >>= ss_mask.speed_shift;
-
- switch (speed) {
- case AT803X_SS_SPEED_10:
- phydev->speed = SPEED_10;
- break;
- case AT803X_SS_SPEED_100:
- phydev->speed = SPEED_100;
- break;
- case AT803X_SS_SPEED_1000:
- phydev->speed = SPEED_1000;
- break;
- case QCA808X_SS_SPEED_2500:
- phydev->speed = SPEED_2500;
- break;
- }
- if (ss & AT803X_SS_DUPLEX)
- phydev->duplex = DUPLEX_FULL;
- else
- phydev->duplex = DUPLEX_HALF;
-
- if (ss & AT803X_SS_MDIX)
- phydev->mdix = ETH_TP_MDI_X;
- else
- phydev->mdix = ETH_TP_MDI;
-
- switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) {
- case AT803X_SFC_MANUAL_MDI:
- phydev->mdix_ctrl = ETH_TP_MDI;
- break;
- case AT803X_SFC_MANUAL_MDIX:
- phydev->mdix_ctrl = ETH_TP_MDI_X;
- break;
- case AT803X_SFC_AUTOMATIC_CROSSOVER:
- phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
- break;
- }
- }
-
- return 0;
-}
-
static int at803x_read_status(struct phy_device *phydev)
{
struct at803x_ss_mask ss_mask = { 0 };
@@ -1006,50 +739,6 @@ static int at803x_read_status(struct phy_device *phydev)
return 0;
}
-static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
-{
- u16 val;
-
- switch (ctrl) {
- case ETH_TP_MDI:
- val = AT803X_SFC_MANUAL_MDI;
- break;
- case ETH_TP_MDI_X:
- val = AT803X_SFC_MANUAL_MDIX;
- break;
- case ETH_TP_MDI_AUTO:
- val = AT803X_SFC_AUTOMATIC_CROSSOVER;
- break;
- default:
- return 0;
- }
-
- return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL,
- AT803X_SFC_MDI_CROSSOVER_MODE_M,
- FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val));
-}
-
-static int at803x_prepare_config_aneg(struct phy_device *phydev)
-{
- int ret;
-
- ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
- if (ret < 0)
- return ret;
-
- /* Changes of the midx bits are disruptive to the normal operation;
- * therefore any changes to these registers must be followed by a
- * software reset to take effect.
- */
- if (ret == 1) {
- ret = genphy_soft_reset(phydev);
- if (ret < 0)
- return ret;
- }
-
- return 0;
-}
-
static int at803x_config_aneg(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
@@ -1065,80 +754,6 @@ static int at803x_config_aneg(struct phy_device *phydev)
return genphy_config_aneg(phydev);
}
-static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
-{
- int val;
-
- val = phy_read(phydev, AT803X_SMART_SPEED);
- if (val < 0)
- return val;
-
- if (val & AT803X_SMART_SPEED_ENABLE)
- *d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2;
- else
- *d = DOWNSHIFT_DEV_DISABLE;
-
- return 0;
-}
-
-static int at803x_set_downshift(struct phy_device *phydev, u8 cnt)
-{
- u16 mask, set;
- int ret;
-
- switch (cnt) {
- case DOWNSHIFT_DEV_DEFAULT_COUNT:
- cnt = AT803X_DEFAULT_DOWNSHIFT;
- fallthrough;
- case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT:
- set = AT803X_SMART_SPEED_ENABLE |
- AT803X_SMART_SPEED_BYPASS_TIMER |
- FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2);
- mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK;
- break;
- case DOWNSHIFT_DEV_DISABLE:
- set = 0;
- mask = AT803X_SMART_SPEED_ENABLE |
- AT803X_SMART_SPEED_BYPASS_TIMER;
- break;
- default:
- return -EINVAL;
- }
-
- ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set);
-
- /* After changing the smart speed settings, we need to perform a
- * software reset, use phy_init_hw() to make sure we set the
- * reapply any values which might got lost during software reset.
- */
- if (ret == 1)
- ret = phy_init_hw(phydev);
-
- return ret;
-}
-
-static int at803x_get_tunable(struct phy_device *phydev,
- struct ethtool_tunable *tuna, void *data)
-{
- switch (tuna->id) {
- case ETHTOOL_PHY_DOWNSHIFT:
- return at803x_get_downshift(phydev, data);
- default:
- return -EOPNOTSUPP;
- }
-}
-
-static int at803x_set_tunable(struct phy_device *phydev,
- struct ethtool_tunable *tuna, const void *data)
-{
- switch (tuna->id) {
- case ETHTOOL_PHY_DOWNSHIFT:
- return at803x_set_downshift(phydev, *(const u8 *)data);
- default:
- return -EOPNOTSUPP;
- }
-}
-
static int at803x_cable_test_result_trans(u16 status)
{
switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) {
@@ -1170,45 +785,6 @@ static bool at803x_cdt_fault_length_valid(u16 status)
return false;
}
-static int at803x_cdt_fault_length(int dt)
-{
- /* According to the datasheet the distance to the fault is
- * DELTA_TIME * 0.824 meters.
- *
- * The author suspect the correct formula is:
- *
- * fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2
- *
- * where c is the speed of light, VF is the velocity factor of
- * the twisted pair cable, 125MHz the counter frequency and
- * we need to divide by 2 because the hardware will measure the
- * round trip time to the fault and back to the PHY.
- *
- * With a VF of 0.69 we get the factor 0.824 mentioned in the
- * datasheet.
- */
- return (dt * 824) / 10;
-}
-
-static int at803x_cdt_start(struct phy_device *phydev,
- u32 cdt_start)
-{
- return phy_write(phydev, AT803X_CDT, cdt_start);
-}
-
-static int at803x_cdt_wait_for_completion(struct phy_device *phydev,
- u32 cdt_en)
-{
- int val, ret;
-
- /* One test run takes about 25ms */
- ret = phy_read_poll_timeout(phydev, AT803X_CDT, val,
- !(val & cdt_en),
- 30000, 100000, true);
-
- return ret < 0 ? ret : 0;
-}
-
static int at803x_cable_test_one_pair(struct phy_device *phydev, int pair)
{
static const int ethtool_pair[] = {
diff --git a/drivers/net/phy/qcom/qcom-phy-lib.c b/drivers/net/phy/qcom/qcom-phy-lib.c
index 7192184429b7..e0295d4b4a51 100644
--- a/drivers/net/phy/qcom/qcom-phy-lib.c
+++ b/drivers/net/phy/qcom/qcom-phy-lib.c
@@ -3,6 +3,9 @@
#include <linux/phy.h>
#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+
#include "qcom.h"
MODULE_DESCRIPTION("Qualcomm PHY driver Common Functions");
@@ -51,3 +54,376 @@ int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data)
return phy_write(phydev, AT803X_DEBUG_DATA, data);
}
EXPORT_SYMBOL_GPL(at803x_debug_reg_write);
+
+int at803x_set_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol)
+{
+ int ret, irq_enabled;
+
+ if (wol->wolopts & WAKE_MAGIC) {
+ struct net_device *ndev = phydev->attached_dev;
+ const u8 *mac;
+ unsigned int i;
+ static const unsigned int offsets[] = {
+ AT803X_LOC_MAC_ADDR_32_47_OFFSET,
+ AT803X_LOC_MAC_ADDR_16_31_OFFSET,
+ AT803X_LOC_MAC_ADDR_0_15_OFFSET,
+ };
+
+ if (!ndev)
+ return -ENODEV;
+
+ mac = (const u8 *)ndev->dev_addr;
+
+ if (!is_valid_ether_addr(mac))
+ return -EINVAL;
+
+ for (i = 0; i < 3; i++)
+ phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
+ mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
+
+ /* Enable WOL interrupt */
+ ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
+ if (ret)
+ return ret;
+ } else {
+ /* Disable WOL interrupt */
+ ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
+ if (ret)
+ return ret;
+ }
+
+ /* Clear WOL status */
+ ret = phy_read(phydev, AT803X_INTR_STATUS);
+ if (ret < 0)
+ return ret;
+
+ /* Check if there are other interrupts except for WOL triggered when PHY is
+ * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can
+ * be passed up to the interrupt PIN.
+ */
+ irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+ if (irq_enabled < 0)
+ return irq_enabled;
+
+ irq_enabled &= ~AT803X_INTR_ENABLE_WOL;
+ if (ret & irq_enabled && !phy_polling_mode(phydev))
+ phy_trigger_machine(phydev);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_set_wol);
+
+void at803x_get_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol)
+{
+ int value;
+
+ wol->supported = WAKE_MAGIC;
+ wol->wolopts = 0;
+
+ value = phy_read(phydev, AT803X_INTR_ENABLE);
+ if (value < 0)
+ return;
+
+ if (value & AT803X_INTR_ENABLE_WOL)
+ wol->wolopts |= WAKE_MAGIC;
+}
+EXPORT_SYMBOL_GPL(at803x_get_wol);
+
+int at803x_ack_interrupt(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_read(phydev, AT803X_INTR_STATUS);
+
+ return (err < 0) ? err : 0;
+}
+EXPORT_SYMBOL_GPL(at803x_ack_interrupt);
+
+int at803x_config_intr(struct phy_device *phydev)
+{
+ int err;
+ int value;
+
+ value = phy_read(phydev, AT803X_INTR_ENABLE);
+
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+ /* Clear any pending interrupts */
+ err = at803x_ack_interrupt(phydev);
+ if (err)
+ return err;
+
+ value |= AT803X_INTR_ENABLE_AUTONEG_ERR;
+ value |= AT803X_INTR_ENABLE_SPEED_CHANGED;
+ value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
+ value |= AT803X_INTR_ENABLE_LINK_FAIL;
+ value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+
+ err = phy_write(phydev, AT803X_INTR_ENABLE, value);
+ } else {
+ err = phy_write(phydev, AT803X_INTR_ENABLE, 0);
+ if (err)
+ return err;
+
+ /* Clear any pending interrupts */
+ err = at803x_ack_interrupt(phydev);
+ }
+
+ return err;
+}
+EXPORT_SYMBOL_GPL(at803x_config_intr);
+
+irqreturn_t at803x_handle_interrupt(struct phy_device *phydev)
+{
+ int irq_status, int_enabled;
+
+ irq_status = phy_read(phydev, AT803X_INTR_STATUS);
+ if (irq_status < 0) {
+ phy_error(phydev);
+ return IRQ_NONE;
+ }
+
+ /* Read the current enabled interrupts */
+ int_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+ if (int_enabled < 0) {
+ phy_error(phydev);
+ return IRQ_NONE;
+ }
+
+ /* See if this was one of our enabled interrupts */
+ if (!(irq_status & int_enabled))
+ return IRQ_NONE;
+
+ phy_trigger_machine(phydev);
+
+ return IRQ_HANDLED;
+}
+EXPORT_SYMBOL_GPL(at803x_handle_interrupt);
+
+int at803x_read_specific_status(struct phy_device *phydev,
+ struct at803x_ss_mask ss_mask)
+{
+ int ss;
+
+ /* Read the AT8035 PHY-Specific Status register, which indicates the
+ * speed and duplex that the PHY is actually using, irrespective of
+ * whether we are in autoneg mode or not.
+ */
+ ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
+ if (ss < 0)
+ return ss;
+
+ if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
+ int sfc, speed;
+
+ sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL);
+ if (sfc < 0)
+ return sfc;
+
+ speed = ss & ss_mask.speed_mask;
+ speed >>= ss_mask.speed_shift;
+
+ switch (speed) {
+ case AT803X_SS_SPEED_10:
+ phydev->speed = SPEED_10;
+ break;
+ case AT803X_SS_SPEED_100:
+ phydev->speed = SPEED_100;
+ break;
+ case AT803X_SS_SPEED_1000:
+ phydev->speed = SPEED_1000;
+ break;
+ case QCA808X_SS_SPEED_2500:
+ phydev->speed = SPEED_2500;
+ break;
+ }
+ if (ss & AT803X_SS_DUPLEX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ if (ss & AT803X_SS_MDIX)
+ phydev->mdix = ETH_TP_MDI_X;
+ else
+ phydev->mdix = ETH_TP_MDI;
+
+ switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) {
+ case AT803X_SFC_MANUAL_MDI:
+ phydev->mdix_ctrl = ETH_TP_MDI;
+ break;
+ case AT803X_SFC_MANUAL_MDIX:
+ phydev->mdix_ctrl = ETH_TP_MDI_X;
+ break;
+ case AT803X_SFC_AUTOMATIC_CROSSOVER:
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+ break;
+ }
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_read_specific_status);
+
+int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+ u16 val;
+
+ switch (ctrl) {
+ case ETH_TP_MDI:
+ val = AT803X_SFC_MANUAL_MDI;
+ break;
+ case ETH_TP_MDI_X:
+ val = AT803X_SFC_MANUAL_MDIX;
+ break;
+ case ETH_TP_MDI_AUTO:
+ val = AT803X_SFC_AUTOMATIC_CROSSOVER;
+ break;
+ default:
+ return 0;
+ }
+
+ return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL,
+ AT803X_SFC_MDI_CROSSOVER_MODE_M,
+ FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val));
+}
+EXPORT_SYMBOL_GPL(at803x_config_mdix);
+
+int at803x_prepare_config_aneg(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
+ if (ret < 0)
+ return ret;
+
+ /* Changes of the midx bits are disruptive to the normal operation;
+ * therefore any changes to these registers must be followed by a
+ * software reset to take effect.
+ */
+ if (ret == 1) {
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_prepare_config_aneg);
+
+static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
+{
+ int val;
+
+ val = phy_read(phydev, AT803X_SMART_SPEED);
+ if (val < 0)
+ return val;
+
+ if (val & AT803X_SMART_SPEED_ENABLE)
+ *d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2;
+ else
+ *d = DOWNSHIFT_DEV_DISABLE;
+
+ return 0;
+}
+
+static int at803x_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+ u16 mask, set;
+ int ret;
+
+ switch (cnt) {
+ case DOWNSHIFT_DEV_DEFAULT_COUNT:
+ cnt = AT803X_DEFAULT_DOWNSHIFT;
+ fallthrough;
+ case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT:
+ set = AT803X_SMART_SPEED_ENABLE |
+ AT803X_SMART_SPEED_BYPASS_TIMER |
+ FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2);
+ mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK;
+ break;
+ case DOWNSHIFT_DEV_DISABLE:
+ set = 0;
+ mask = AT803X_SMART_SPEED_ENABLE |
+ AT803X_SMART_SPEED_BYPASS_TIMER;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set);
+
+ /* After changing the smart speed settings, we need to perform a
+ * software reset, use phy_init_hw() to make sure we set the
+ * reapply any values which might got lost during software reset.
+ */
+ if (ret == 1)
+ ret = phy_init_hw(phydev);
+
+ return ret;
+}
+
+int at803x_get_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, void *data)
+{
+ switch (tuna->id) {
+ case ETHTOOL_PHY_DOWNSHIFT:
+ return at803x_get_downshift(phydev, data);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+EXPORT_SYMBOL_GPL(at803x_get_tunable);
+
+int at803x_set_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, const void *data)
+{
+ switch (tuna->id) {
+ case ETHTOOL_PHY_DOWNSHIFT:
+ return at803x_set_downshift(phydev, *(const u8 *)data);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+EXPORT_SYMBOL_GPL(at803x_set_tunable);
+
+int at803x_cdt_fault_length(int dt)
+{
+ /* According to the datasheet the distance to the fault is
+ * DELTA_TIME * 0.824 meters.
+ *
+ * The author suspect the correct formula is:
+ *
+ * fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2
+ *
+ * where c is the speed of light, VF is the velocity factor of
+ * the twisted pair cable, 125MHz the counter frequency and
+ * we need to divide by 2 because the hardware will measure the
+ * round trip time to the fault and back to the PHY.
+ *
+ * With a VF of 0.69 we get the factor 0.824 mentioned in the
+ * datasheet.
+ */
+ return (dt * 824) / 10;
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_fault_length);
+
+int at803x_cdt_start(struct phy_device *phydev, u32 cdt_start)
+{
+ return phy_write(phydev, AT803X_CDT, cdt_start);
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_start);
+
+int at803x_cdt_wait_for_completion(struct phy_device *phydev,
+ u32 cdt_en)
+{
+ int val, ret;
+
+ /* One test run takes about 25ms */
+ ret = phy_read_poll_timeout(phydev, AT803X_CDT, val,
+ !(val & cdt_en),
+ 30000, 100000, true);
+
+ return ret < 0 ? ret : 0;
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_wait_for_completion);
diff --git a/drivers/net/phy/qcom/qcom.h b/drivers/net/phy/qcom/qcom.h
index 8eb476d7c282..c127d8f50f0f 100644
--- a/drivers/net/phy/qcom/qcom.h
+++ b/drivers/net/phy/qcom/qcom.h
@@ -1,5 +1,63 @@
/* SPDX-License-Identifier: GPL-2.0 */
+#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10
+#define AT803X_SFC_ASSERT_CRS BIT(11)
+#define AT803X_SFC_FORCE_LINK BIT(10)
+#define AT803X_SFC_MDI_CROSSOVER_MODE_M GENMASK(6, 5)
+#define AT803X_SFC_AUTOMATIC_CROSSOVER 0x3
+#define AT803X_SFC_MANUAL_MDIX 0x1
+#define AT803X_SFC_MANUAL_MDI 0x0
+#define AT803X_SFC_SQE_TEST BIT(2)
+#define AT803X_SFC_POLARITY_REVERSAL BIT(1)
+#define AT803X_SFC_DISABLE_JABBER BIT(0)
+
+#define AT803X_SPECIFIC_STATUS 0x11
+#define AT803X_SS_SPEED_MASK GENMASK(15, 14)
+#define AT803X_SS_SPEED_1000 2
+#define AT803X_SS_SPEED_100 1
+#define AT803X_SS_SPEED_10 0
+#define AT803X_SS_DUPLEX BIT(13)
+#define AT803X_SS_SPEED_DUPLEX_RESOLVED BIT(11)
+#define AT803X_SS_MDIX BIT(6)
+
+#define QCA808X_SS_SPEED_MASK GENMASK(9, 7)
+#define QCA808X_SS_SPEED_2500 4
+
+#define AT803X_INTR_ENABLE 0x12
+#define AT803X_INTR_ENABLE_AUTONEG_ERR BIT(15)
+#define AT803X_INTR_ENABLE_SPEED_CHANGED BIT(14)
+#define AT803X_INTR_ENABLE_DUPLEX_CHANGED BIT(13)
+#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
+#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
+#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
+#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
+#define AT803X_INTR_ENABLE_WOL BIT(0)
+
+#define AT803X_INTR_STATUS 0x13
+
+#define AT803X_SMART_SPEED 0x14
+#define AT803X_SMART_SPEED_ENABLE BIT(5)
+#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK GENMASK(4, 2)
+#define AT803X_SMART_SPEED_BYPASS_TIMER BIT(1)
+
+#define AT803X_CDT 0x16
+#define AT803X_CDT_MDI_PAIR_MASK GENMASK(9, 8)
+#define AT803X_CDT_ENABLE_TEST BIT(0)
+#define AT803X_CDT_STATUS 0x1c
+#define AT803X_CDT_STATUS_STAT_NORMAL 0
+#define AT803X_CDT_STATUS_STAT_SHORT 1
+#define AT803X_CDT_STATUS_STAT_OPEN 2
+#define AT803X_CDT_STATUS_STAT_FAIL 3
+#define AT803X_CDT_STATUS_STAT_MASK GENMASK(9, 8)
+#define AT803X_CDT_STATUS_DELTA_TIME_MASK GENMASK(7, 0)
+
+#define AT803X_LOC_MAC_ADDR_0_15_OFFSET 0x804C
+#define AT803X_LOC_MAC_ADDR_16_31_OFFSET 0x804B
+#define AT803X_LOC_MAC_ADDR_32_47_OFFSET 0x804A
+
#define AT803X_DEBUG_ADDR 0x1D
#define AT803X_DEBUG_DATA 0x1E
@@ -16,6 +74,10 @@
#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13)
#define AT803X_DEBUG_HIB_CTRL_PS_HIB_EN BIT(15)
+#define AT803X_DEFAULT_DOWNSHIFT 5
+#define AT803X_MIN_DOWNSHIFT 2
+#define AT803X_MAX_DOWNSHIFT 9
+
enum stat_access_type {
PHY,
MMD
@@ -28,7 +90,31 @@ struct at803x_hw_stat {
enum stat_access_type access_type;
};
+struct at803x_ss_mask {
+ u16 speed_mask;
+ u8 speed_shift;
+};
+
int at803x_debug_reg_read(struct phy_device *phydev, u16 reg);
int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
u16 clear, u16 set);
int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data);
+int at803x_set_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol);
+void at803x_get_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol);
+int at803x_ack_interrupt(struct phy_device *phydev);
+int at803x_config_intr(struct phy_device *phydev);
+irqreturn_t at803x_handle_interrupt(struct phy_device *phydev);
+int at803x_read_specific_status(struct phy_device *phydev,
+ struct at803x_ss_mask ss_mask);
+int at803x_config_mdix(struct phy_device *phydev, u8 ctrl);
+int at803x_prepare_config_aneg(struct phy_device *phydev);
+int at803x_get_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, void *data);
+int at803x_set_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, const void *data);
+int at803x_cdt_fault_length(int dt);
+int at803x_cdt_start(struct phy_device *phydev, u32 cdt_start);
+int at803x_cdt_wait_for_completion(struct phy_device *phydev,
+ u32 cdt_en);
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [net-next PATCH v4 5/5] net: phy: qcom: detach qca808x PHY driver from at803x
2024-01-29 14:15 [net-next PATCH v4 0/5] net: phy: split at803x Christian Marangi
` (3 preceding siblings ...)
2024-01-29 14:15 ` [net-next PATCH v4 4/5] net: phy: qcom: move additional functions to shared library Christian Marangi
@ 2024-01-29 14:15 ` Christian Marangi
2024-02-01 0:40 ` [net-next PATCH v4 0/5] net: phy: split at803x patchwork-bot+netdevbpf
5 siblings, 0 replies; 7+ messages in thread
From: Christian Marangi @ 2024-01-29 14:15 UTC (permalink / raw)
To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Bjorn Andersson,
Konrad Dybcio, linux-kernel, netdev, linux-arm-msm
Cc: Christian Marangi
Almost all the QCA8081 PHY driver OPs are specific and only some of them
use the generic at803x.
To make the at803x code slimmer, move all the specific qca808x regs and
functions to a dedicated PHY driver.
Probe function and priv struct is reworked to allocate and use only the
qca808x specific data. Unused data from at803x PHY driver are dropped
from at803x priv struct.
Also a new Kconfig is introduced QCA808X_PHY, to compile the newly
introduced PHY driver for QCA8081 PHY.
As the Kconfig name starts with Qualcomm the same order is kept.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/qcom/Kconfig | 6 +
drivers/net/phy/qcom/Makefile | 1 +
drivers/net/phy/qcom/at803x.c | 897 +------------------------------
drivers/net/phy/qcom/qca808x.c | 934 +++++++++++++++++++++++++++++++++
4 files changed, 942 insertions(+), 896 deletions(-)
create mode 100644 drivers/net/phy/qcom/qca808x.c
diff --git a/drivers/net/phy/qcom/Kconfig b/drivers/net/phy/qcom/Kconfig
index ba78bbe31857..80db24deb689 100644
--- a/drivers/net/phy/qcom/Kconfig
+++ b/drivers/net/phy/qcom/Kconfig
@@ -14,3 +14,9 @@ config QCA83XX_PHY
select QCOM_NET_PHYLIB
help
Currently supports the internal QCA8337(Internal qca8k PHY) model
+
+config QCA808X_PHY
+ tristate "Qualcomm QCA808x PHYs"
+ select QCOM_NET_PHYLIB
+ help
+ Currently supports the QCA8081 model
diff --git a/drivers/net/phy/qcom/Makefile b/drivers/net/phy/qcom/Makefile
index 3d98e397e063..0362d7ed47be 100644
--- a/drivers/net/phy/qcom/Makefile
+++ b/drivers/net/phy/qcom/Makefile
@@ -2,3 +2,4 @@
obj-$(CONFIG_QCOM_NET_PHYLIB) += qcom-phy-lib.o
obj-$(CONFIG_AT803X_PHY) += at803x.o
obj-$(CONFIG_QCA83XX_PHY) += qca83xx.o
+obj-$(CONFIG_QCA808X_PHY) += qca808x.o
diff --git a/drivers/net/phy/qcom/at803x.c b/drivers/net/phy/qcom/at803x.c
index 6a753498b994..36b70e88394e 100644
--- a/drivers/net/phy/qcom/at803x.c
+++ b/drivers/net/phy/qcom/at803x.c
@@ -96,8 +96,6 @@
#define ATH8035_PHY_ID 0x004dd072
#define AT8030_PHY_ID_MASK 0xffffffef
-#define QCA8081_PHY_ID 0x004dd101
-
#define QCA9561_PHY_ID 0x004dd042
#define AT803X_PAGE_FIBER 0
@@ -110,201 +108,7 @@
/* disable hibernation mode */
#define AT803X_DISABLE_HIBERNATION_MODE BIT(2)
-/* ADC threshold */
-#define QCA808X_PHY_DEBUG_ADC_THRESHOLD 0x2c80
-#define QCA808X_ADC_THRESHOLD_MASK GENMASK(7, 0)
-#define QCA808X_ADC_THRESHOLD_80MV 0
-#define QCA808X_ADC_THRESHOLD_100MV 0xf0
-#define QCA808X_ADC_THRESHOLD_200MV 0x0f
-#define QCA808X_ADC_THRESHOLD_300MV 0xff
-
-/* CLD control */
-#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7 0x8007
-#define QCA808X_8023AZ_AFE_CTRL_MASK GENMASK(8, 4)
-#define QCA808X_8023AZ_AFE_EN 0x90
-
-/* AZ control */
-#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL 0x8008
-#define QCA808X_MMD3_AZ_TRAINING_VAL 0x1c32
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB 0x8014
-#define QCA808X_MSE_THRESHOLD_20DB_VALUE 0x529
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB 0x800E
-#define QCA808X_MSE_THRESHOLD_17DB_VALUE 0x341
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB 0x801E
-#define QCA808X_MSE_THRESHOLD_27DB_VALUE 0x419
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB 0x8020
-#define QCA808X_MSE_THRESHOLD_28DB_VALUE 0x341
-
-#define QCA808X_PHY_MMD7_TOP_OPTION1 0x901c
-#define QCA808X_TOP_OPTION1_DATA 0x0
-
-#define QCA808X_PHY_MMD3_DEBUG_1 0xa100
-#define QCA808X_MMD3_DEBUG_1_VALUE 0x9203
-#define QCA808X_PHY_MMD3_DEBUG_2 0xa101
-#define QCA808X_MMD3_DEBUG_2_VALUE 0x48ad
-#define QCA808X_PHY_MMD3_DEBUG_3 0xa103
-#define QCA808X_MMD3_DEBUG_3_VALUE 0x1698
-#define QCA808X_PHY_MMD3_DEBUG_4 0xa105
-#define QCA808X_MMD3_DEBUG_4_VALUE 0x8001
-#define QCA808X_PHY_MMD3_DEBUG_5 0xa106
-#define QCA808X_MMD3_DEBUG_5_VALUE 0x1111
-#define QCA808X_PHY_MMD3_DEBUG_6 0xa011
-#define QCA808X_MMD3_DEBUG_6_VALUE 0x5f85
-
-/* master/slave seed config */
-#define QCA808X_PHY_DEBUG_LOCAL_SEED 9
-#define QCA808X_MASTER_SLAVE_SEED_ENABLE BIT(1)
-#define QCA808X_MASTER_SLAVE_SEED_CFG GENMASK(12, 2)
-#define QCA808X_MASTER_SLAVE_SEED_RANGE 0x32
-
-/* Hibernation yields lower power consumpiton in contrast with normal operation mode.
- * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s.
- */
-#define QCA808X_DBG_AN_TEST 0xb
-#define QCA808X_HIBERNATION_EN BIT(15)
-
-#define QCA808X_CDT_ENABLE_TEST BIT(15)
-#define QCA808X_CDT_INTER_CHECK_DIS BIT(13)
-#define QCA808X_CDT_STATUS BIT(11)
-#define QCA808X_CDT_LENGTH_UNIT BIT(10)
-
-#define QCA808X_MMD3_CDT_STATUS 0x8064
-#define QCA808X_MMD3_CDT_DIAG_PAIR_A 0x8065
-#define QCA808X_MMD3_CDT_DIAG_PAIR_B 0x8066
-#define QCA808X_MMD3_CDT_DIAG_PAIR_C 0x8067
-#define QCA808X_MMD3_CDT_DIAG_PAIR_D 0x8068
-#define QCA808X_CDT_DIAG_LENGTH_SAME_SHORT GENMASK(15, 8)
-#define QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT GENMASK(7, 0)
-
-#define QCA808X_CDT_CODE_PAIR_A GENMASK(15, 12)
-#define QCA808X_CDT_CODE_PAIR_B GENMASK(11, 8)
-#define QCA808X_CDT_CODE_PAIR_C GENMASK(7, 4)
-#define QCA808X_CDT_CODE_PAIR_D GENMASK(3, 0)
-
-#define QCA808X_CDT_STATUS_STAT_TYPE GENMASK(1, 0)
-#define QCA808X_CDT_STATUS_STAT_FAIL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 0)
-#define QCA808X_CDT_STATUS_STAT_NORMAL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 1)
-#define QCA808X_CDT_STATUS_STAT_SAME_OPEN FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 2)
-#define QCA808X_CDT_STATUS_STAT_SAME_SHORT FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 3)
-
-#define QCA808X_CDT_STATUS_STAT_MDI GENMASK(3, 2)
-#define QCA808X_CDT_STATUS_STAT_MDI1 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 1)
-#define QCA808X_CDT_STATUS_STAT_MDI2 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 2)
-#define QCA808X_CDT_STATUS_STAT_MDI3 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 3)
-
-/* NORMAL are MDI with type set to 0 */
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI1
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
- QCA808X_CDT_STATUS_STAT_MDI1)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
- QCA808X_CDT_STATUS_STAT_MDI1)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI2
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
- QCA808X_CDT_STATUS_STAT_MDI2)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
- QCA808X_CDT_STATUS_STAT_MDI2)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI3
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
- QCA808X_CDT_STATUS_STAT_MDI3)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
- QCA808X_CDT_STATUS_STAT_MDI3)
-
-/* Added for reference of existence but should be handled by wait_for_completion already */
-#define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3))
-
-#define QCA808X_MMD7_LED_GLOBAL 0x8073
-#define QCA808X_LED_BLINK_1 GENMASK(11, 6)
-#define QCA808X_LED_BLINK_2 GENMASK(5, 0)
-/* Values are the same for both BLINK_1 and BLINK_2 */
-#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3)
-#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
-#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
-#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
-#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
-#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
-#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
-#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
-#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
-#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0)
-#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
-#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
-#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
-#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
-#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
-#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
-#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
-#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
-
-#define QCA808X_MMD7_LED2_CTRL 0x8074
-#define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075
-#define QCA808X_MMD7_LED1_CTRL 0x8076
-#define QCA808X_MMD7_LED1_FORCE_CTRL 0x8077
-#define QCA808X_MMD7_LED0_CTRL 0x8078
-#define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2))
-
-/* LED hw control pattern is the same for every LED */
-#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0)
-#define QCA808X_LED_SPEED2500_ON BIT(15)
-#define QCA808X_LED_SPEED2500_BLINK BIT(14)
-/* Follow blink trigger even if duplex or speed condition doesn't match */
-#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13)
-#define QCA808X_LED_FULL_DUPLEX_ON BIT(12)
-#define QCA808X_LED_HALF_DUPLEX_ON BIT(11)
-#define QCA808X_LED_TX_BLINK BIT(10)
-#define QCA808X_LED_RX_BLINK BIT(9)
-#define QCA808X_LED_TX_ON_10MS BIT(8)
-#define QCA808X_LED_RX_ON_10MS BIT(7)
-#define QCA808X_LED_SPEED1000_ON BIT(6)
-#define QCA808X_LED_SPEED100_ON BIT(5)
-#define QCA808X_LED_SPEED10_ON BIT(4)
-#define QCA808X_LED_COLLISION_BLINK BIT(3)
-#define QCA808X_LED_SPEED1000_BLINK BIT(2)
-#define QCA808X_LED_SPEED100_BLINK BIT(1)
-#define QCA808X_LED_SPEED10_BLINK BIT(0)
-
-#define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079
-#define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2))
-
-/* LED force ctrl is the same for every LED
- * No documentation exist for this, not even internal one
- * with NDA as QCOM gives only info about configuring
- * hw control pattern rules and doesn't indicate any way
- * to force the LED to specific mode.
- * These define comes from reverse and testing and maybe
- * lack of some info or some info are not entirely correct.
- * For the basic LED control and hw control these finding
- * are enough to support LED control in all the required APIs.
- *
- * On doing some comparison with implementation with qca807x,
- * it was found that it's 1:1 equal to it and confirms all the
- * reverse done. It was also found further specification with the
- * force mode and the blink modes.
- */
-#define QCA808X_LED_FORCE_EN BIT(15)
-#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13)
-#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
-#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
-#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
-#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
-
-#define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a
-/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
- * LED to active high. It's not clear what BIT 3 and BIT 4 does.
- */
-#define QCA808X_LED_ACTIVE_HIGH BIT(6)
-
-/* QCA808X 1G chip type */
-#define QCA808X_PHY_MMD7_CHIP_TYPE 0x901d
-#define QCA808X_PHY_CHIP_TYPE_1G BIT(0)
-
-#define QCA8081_PHY_SERDES_MMD1_FIFO_CTRL 0x9072
-#define QCA8081_PHY_FIFO_RSTN BIT(11)
-
-MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
+MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver");
MODULE_AUTHOR("Matus Ujhelyi");
MODULE_LICENSE("GPL");
@@ -318,7 +122,6 @@ struct at803x_priv {
bool is_1000basex;
struct regulator_dev *vddio_rdev;
struct regulator_dev *vddh_rdev;
- int led_polarity_mode;
};
struct at803x_context {
@@ -519,9 +322,6 @@ static int at803x_probe(struct phy_device *phydev)
if (!priv)
return -ENOMEM;
- /* Init LED polarity mode to -1 */
- priv->led_polarity_mode = -1;
-
phydev->priv = priv;
ret = at803x_parse_dt(phydev);
@@ -1216,672 +1016,6 @@ static int at8035_probe(struct phy_device *phydev)
return at8035_parse_dt(phydev);
}
-static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
-{
- int ret;
-
- /* Enable fast retrain */
- ret = genphy_c45_fast_retrain(phydev, true);
- if (ret)
- return ret;
-
- phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1,
- QCA808X_TOP_OPTION1_DATA);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB,
- QCA808X_MSE_THRESHOLD_20DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB,
- QCA808X_MSE_THRESHOLD_17DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB,
- QCA808X_MSE_THRESHOLD_27DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB,
- QCA808X_MSE_THRESHOLD_28DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1,
- QCA808X_MMD3_DEBUG_1_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4,
- QCA808X_MMD3_DEBUG_4_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5,
- QCA808X_MMD3_DEBUG_5_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3,
- QCA808X_MMD3_DEBUG_3_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6,
- QCA808X_MMD3_DEBUG_6_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2,
- QCA808X_MMD3_DEBUG_2_VALUE);
-
- return 0;
-}
-
-static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable)
-{
- u16 seed_value;
-
- if (!enable)
- return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
- QCA808X_MASTER_SLAVE_SEED_ENABLE, 0);
-
- seed_value = get_random_u32_below(QCA808X_MASTER_SLAVE_SEED_RANGE);
- return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
- QCA808X_MASTER_SLAVE_SEED_CFG | QCA808X_MASTER_SLAVE_SEED_ENABLE,
- FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value) |
- QCA808X_MASTER_SLAVE_SEED_ENABLE);
-}
-
-static bool qca808x_is_prefer_master(struct phy_device *phydev)
-{
- return (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_FORCE) ||
- (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_PREFERRED);
-}
-
-static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
-{
- return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
-}
-
-static int qca808x_config_init(struct phy_device *phydev)
-{
- int ret;
-
- /* Active adc&vga on 802.3az for the link 1000M and 100M */
- ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7,
- QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN);
- if (ret)
- return ret;
-
- /* Adjust the threshold on 802.3az for the link 1000M */
- ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
- QCA808X_PHY_MMD3_AZ_TRAINING_CTRL,
- QCA808X_MMD3_AZ_TRAINING_VAL);
- if (ret)
- return ret;
-
- if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
- /* Config the fast retrain for the link 2500M */
- ret = qca808x_phy_fast_retrain_config(phydev);
- if (ret)
- return ret;
-
- ret = genphy_read_master_slave(phydev);
- if (ret < 0)
- return ret;
-
- if (!qca808x_is_prefer_master(phydev)) {
- /* Enable seed and configure lower ramdom seed to make phy
- * linked as slave mode.
- */
- ret = qca808x_phy_ms_seed_enable(phydev, true);
- if (ret)
- return ret;
- }
- }
-
- /* Configure adc threshold as 100mv for the link 10M */
- return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
- QCA808X_ADC_THRESHOLD_MASK,
- QCA808X_ADC_THRESHOLD_100MV);
-}
-
-static int qca808x_read_status(struct phy_device *phydev)
-{
- struct at803x_ss_mask ss_mask = { 0 };
- int ret;
-
- ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
- if (ret < 0)
- return ret;
-
- linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising,
- ret & MDIO_AN_10GBT_STAT_LP2_5G);
-
- ret = genphy_read_status(phydev);
- if (ret)
- return ret;
-
- /* qca8081 takes the different bits for speed value from at803x */
- ss_mask.speed_mask = QCA808X_SS_SPEED_MASK;
- ss_mask.speed_shift = __bf_shf(QCA808X_SS_SPEED_MASK);
- ret = at803x_read_specific_status(phydev, ss_mask);
- if (ret < 0)
- return ret;
-
- if (phydev->link) {
- if (phydev->speed == SPEED_2500)
- phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
- else
- phydev->interface = PHY_INTERFACE_MODE_SGMII;
- } else {
- /* generate seed as a lower random value to make PHY linked as SLAVE easily,
- * except for master/slave configuration fault detected or the master mode
- * preferred.
- *
- * the reason for not putting this code into the function link_change_notify is
- * the corner case where the link partner is also the qca8081 PHY and the seed
- * value is configured as the same value, the link can't be up and no link change
- * occurs.
- */
- if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
- if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR ||
- qca808x_is_prefer_master(phydev)) {
- qca808x_phy_ms_seed_enable(phydev, false);
- } else {
- qca808x_phy_ms_seed_enable(phydev, true);
- }
- }
- }
-
- return 0;
-}
-
-static int qca808x_soft_reset(struct phy_device *phydev)
-{
- int ret;
-
- ret = genphy_soft_reset(phydev);
- if (ret < 0)
- return ret;
-
- if (qca808x_has_fast_retrain_or_slave_seed(phydev))
- ret = qca808x_phy_ms_seed_enable(phydev, true);
-
- return ret;
-}
-
-static bool qca808x_cdt_fault_length_valid(int cdt_code)
-{
- switch (cdt_code) {
- case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
- return true;
- default:
- return false;
- }
-}
-
-static int qca808x_cable_test_result_trans(int cdt_code)
-{
- switch (cdt_code) {
- case QCA808X_CDT_STATUS_STAT_NORMAL:
- return ETHTOOL_A_CABLE_RESULT_CODE_OK;
- case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
- return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
- case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
- return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
- return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
- case QCA808X_CDT_STATUS_STAT_FAIL:
- default:
- return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
- }
-}
-
-static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair,
- int result)
-{
- int val;
- u32 cdt_length_reg = 0;
-
- switch (pair) {
- case ETHTOOL_A_CABLE_PAIR_A:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A;
- break;
- case ETHTOOL_A_CABLE_PAIR_B:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B;
- break;
- case ETHTOOL_A_CABLE_PAIR_C:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C;
- break;
- case ETHTOOL_A_CABLE_PAIR_D:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D;
- break;
- default:
- return -EINVAL;
- }
-
- val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg);
- if (val < 0)
- return val;
-
- if (result == ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT)
- val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_SAME_SHORT, val);
- else
- val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT, val);
-
- return at803x_cdt_fault_length(val);
-}
-
-static int qca808x_cable_test_start(struct phy_device *phydev)
-{
- int ret;
-
- /* perform CDT with the following configs:
- * 1. disable hibernation.
- * 2. force PHY working in MDI mode.
- * 3. for PHY working in 1000BaseT.
- * 4. configure the threshold.
- */
-
- ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0);
- if (ret < 0)
- return ret;
-
- ret = at803x_config_mdix(phydev, ETH_TP_MDI);
- if (ret < 0)
- return ret;
-
- /* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */
- phydev->duplex = DUPLEX_FULL;
- phydev->speed = SPEED_1000;
- ret = genphy_c45_pma_setup_forced(phydev);
- if (ret < 0)
- return ret;
-
- ret = genphy_setup_forced(phydev);
- if (ret < 0)
- return ret;
-
- /* configure the thresholds for open, short, pair ok test */
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
-
- return 0;
-}
-
-static int qca808x_cable_test_get_pair_status(struct phy_device *phydev, u8 pair,
- u16 status)
-{
- int length, result;
- u16 pair_code;
-
- switch (pair) {
- case ETHTOOL_A_CABLE_PAIR_A:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, status);
- break;
- case ETHTOOL_A_CABLE_PAIR_B:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, status);
- break;
- case ETHTOOL_A_CABLE_PAIR_C:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, status);
- break;
- case ETHTOOL_A_CABLE_PAIR_D:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, status);
- break;
- default:
- return -EINVAL;
- }
-
- result = qca808x_cable_test_result_trans(pair_code);
- ethnl_cable_test_result(phydev, pair, result);
-
- if (qca808x_cdt_fault_length_valid(pair_code)) {
- length = qca808x_cdt_fault_length(phydev, pair, result);
- ethnl_cable_test_fault_length(phydev, pair, length);
- }
-
- return 0;
-}
-
-static int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished)
-{
- int ret, val;
-
- *finished = false;
-
- val = QCA808X_CDT_ENABLE_TEST |
- QCA808X_CDT_LENGTH_UNIT;
- ret = at803x_cdt_start(phydev, val);
- if (ret)
- return ret;
-
- ret = at803x_cdt_wait_for_completion(phydev, QCA808X_CDT_ENABLE_TEST);
- if (ret)
- return ret;
-
- val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS);
- if (val < 0)
- return val;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_A, val);
- if (ret)
- return ret;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_B, val);
- if (ret)
- return ret;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_C, val);
- if (ret)
- return ret;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_D, val);
- if (ret)
- return ret;
-
- *finished = true;
-
- return 0;
-}
-
-static int qca808x_get_features(struct phy_device *phydev)
-{
- int ret;
-
- ret = genphy_c45_pma_read_abilities(phydev);
- if (ret)
- return ret;
-
- /* The autoneg ability is not existed in bit3 of MMD7.1,
- * but it is supported by qca808x PHY, so we add it here
- * manually.
- */
- linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
-
- /* As for the qca8081 1G version chip, the 2500baseT ability is also
- * existed in the bit0 of MMD1.21, we need to remove it manually if
- * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
- */
- ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
- if (ret < 0)
- return ret;
-
- if (QCA808X_PHY_CHIP_TYPE_1G & ret)
- linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
-
- return 0;
-}
-
-static int qca808x_config_aneg(struct phy_device *phydev)
-{
- int phy_ctrl = 0;
- int ret;
-
- ret = at803x_prepare_config_aneg(phydev);
- if (ret)
- return ret;
-
- /* The reg MII_BMCR also needs to be configured for force mode, the
- * genphy_config_aneg is also needed.
- */
- if (phydev->autoneg == AUTONEG_DISABLE)
- genphy_c45_pma_setup_forced(phydev);
-
- if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising))
- phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G;
-
- ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
- MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl);
- if (ret < 0)
- return ret;
-
- return __genphy_config_aneg(phydev, ret);
-}
-
-static void qca808x_link_change_notify(struct phy_device *phydev)
-{
- /* Assert interface sgmii fifo on link down, deassert it on link up,
- * the interface device address is always phy address added by 1.
- */
- mdiobus_c45_modify_changed(phydev->mdio.bus, phydev->mdio.addr + 1,
- MDIO_MMD_PMAPMD, QCA8081_PHY_SERDES_MMD1_FIFO_CTRL,
- QCA8081_PHY_FIFO_RSTN,
- phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
-}
-
-static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
- u16 *offload_trigger)
-{
- /* Parsing specific to netdev trigger */
- if (test_bit(TRIGGER_NETDEV_TX, &rules))
- *offload_trigger |= QCA808X_LED_TX_BLINK;
- if (test_bit(TRIGGER_NETDEV_RX, &rules))
- *offload_trigger |= QCA808X_LED_RX_BLINK;
- if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
- *offload_trigger |= QCA808X_LED_SPEED10_ON;
- if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
- *offload_trigger |= QCA808X_LED_SPEED100_ON;
- if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
- *offload_trigger |= QCA808X_LED_SPEED1000_ON;
- if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
- *offload_trigger |= QCA808X_LED_SPEED2500_ON;
- if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
- *offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
- if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
- *offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
-
- if (rules && !*offload_trigger)
- return -EOPNOTSUPP;
-
- /* Enable BLINK_CHECK_BYPASS by default to make the LED
- * blink even with duplex or speed mode not enabled.
- */
- *offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
-
- return 0;
-}
-
-static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
-{
- u16 reg;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_FORCE_EN);
-}
-
-static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
- unsigned long rules)
-{
- u16 offload_trigger = 0;
-
- if (index > 2)
- return -EINVAL;
-
- return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
-}
-
-static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
- unsigned long rules)
-{
- u16 reg, offload_trigger = 0;
- int ret;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_CTRL(index);
-
- ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
- if (ret)
- return ret;
-
- ret = qca808x_led_hw_control_enable(phydev, index);
- if (ret)
- return ret;
-
- return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_PATTERN_MASK,
- offload_trigger);
-}
-
-static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
-{
- u16 reg;
- int val;
-
- if (index > 2)
- return false;
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
-
- return !(val & QCA808X_LED_FORCE_EN);
-}
-
-static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
- unsigned long *rules)
-{
- u16 reg;
- int val;
-
- if (index > 2)
- return -EINVAL;
-
- /* Check if we have hw control enabled */
- if (qca808x_led_hw_control_status(phydev, index))
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_CTRL(index);
-
- val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
- if (val & QCA808X_LED_TX_BLINK)
- set_bit(TRIGGER_NETDEV_TX, rules);
- if (val & QCA808X_LED_RX_BLINK)
- set_bit(TRIGGER_NETDEV_RX, rules);
- if (val & QCA808X_LED_SPEED10_ON)
- set_bit(TRIGGER_NETDEV_LINK_10, rules);
- if (val & QCA808X_LED_SPEED100_ON)
- set_bit(TRIGGER_NETDEV_LINK_100, rules);
- if (val & QCA808X_LED_SPEED1000_ON)
- set_bit(TRIGGER_NETDEV_LINK_1000, rules);
- if (val & QCA808X_LED_SPEED2500_ON)
- set_bit(TRIGGER_NETDEV_LINK_2500, rules);
- if (val & QCA808X_LED_HALF_DUPLEX_ON)
- set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
- if (val & QCA808X_LED_FULL_DUPLEX_ON)
- set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
-
- return 0;
-}
-
-static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
-{
- u16 reg;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_CTRL(index);
-
- return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_PATTERN_MASK);
-}
-
-static int qca808x_led_brightness_set(struct phy_device *phydev,
- u8 index, enum led_brightness value)
-{
- u16 reg;
- int ret;
-
- if (index > 2)
- return -EINVAL;
-
- if (!value) {
- ret = qca808x_led_hw_control_reset(phydev, index);
- if (ret)
- return ret;
- }
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
- QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON :
- QCA808X_LED_FORCE_OFF);
-}
-
-static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
- unsigned long *delay_on,
- unsigned long *delay_off)
-{
- int ret;
- u16 reg;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- /* Set blink to 50% off, 50% on at 4Hz by default */
- ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
- QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
- QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
- if (ret)
- return ret;
-
- /* We use BLINK_1 for normal blinking */
- ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
- QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
- if (ret)
- return ret;
-
- /* We set blink to 4Hz, aka 250ms */
- *delay_on = 250 / 2;
- *delay_off = 250 / 2;
-
- return 0;
-}
-
-static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
- unsigned long modes)
-{
- struct at803x_priv *priv = phydev->priv;
- bool active_low = false;
- u32 mode;
-
- for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
- switch (mode) {
- case PHY_LED_ACTIVE_LOW:
- active_low = true;
- break;
- default:
- return -EINVAL;
- }
- }
-
- /* PHY polarity is global and can't be set per LED.
- * To detect this, check if last requested polarity mode
- * match the new one.
- */
- if (priv->led_polarity_mode >= 0 &&
- priv->led_polarity_mode != active_low) {
- phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
- return -EINVAL;
- }
-
- /* Save the last PHY polarity mode */
- priv->led_polarity_mode = active_low;
-
- return phy_modify_mmd(phydev, MDIO_MMD_AN,
- QCA808X_MMD7_LED_POLARITY_CTRL,
- QCA808X_LED_ACTIVE_HIGH,
- active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
-}
-
static struct phy_driver at803x_driver[] = {
{
/* Qualcomm Atheros AR8035 */
@@ -1989,34 +1123,6 @@ static struct phy_driver at803x_driver[] = {
.read_status = at803x_read_status,
.soft_reset = genphy_soft_reset,
.config_aneg = at803x_config_aneg,
-}, {
- /* Qualcomm QCA8081 */
- PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
- .name = "Qualcomm QCA8081",
- .flags = PHY_POLL_CABLE_TEST,
- .probe = at803x_probe,
- .config_intr = at803x_config_intr,
- .handle_interrupt = at803x_handle_interrupt,
- .get_tunable = at803x_get_tunable,
- .set_tunable = at803x_set_tunable,
- .set_wol = at803x_set_wol,
- .get_wol = at803x_get_wol,
- .get_features = qca808x_get_features,
- .config_aneg = qca808x_config_aneg,
- .suspend = genphy_suspend,
- .resume = genphy_resume,
- .read_status = qca808x_read_status,
- .config_init = qca808x_config_init,
- .soft_reset = qca808x_soft_reset,
- .cable_test_start = qca808x_cable_test_start,
- .cable_test_get_status = qca808x_cable_test_get_status,
- .link_change_notify = qca808x_link_change_notify,
- .led_brightness_set = qca808x_led_brightness_set,
- .led_blink_set = qca808x_led_blink_set,
- .led_hw_is_supported = qca808x_led_hw_is_supported,
- .led_hw_control_set = qca808x_led_hw_control_set,
- .led_hw_control_get = qca808x_led_hw_control_get,
- .led_polarity_set = qca808x_led_polarity_set,
}, };
module_phy_driver(at803x_driver);
@@ -2028,7 +1134,6 @@ static struct mdio_device_id __maybe_unused atheros_tbl[] = {
{ PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) },
{ PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) },
{ PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) },
- { PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
{ }
};
diff --git a/drivers/net/phy/qcom/qca808x.c b/drivers/net/phy/qcom/qca808x.c
new file mode 100644
index 000000000000..0f549027d899
--- /dev/null
+++ b/drivers/net/phy/qcom/qca808x.c
@@ -0,0 +1,934 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/phy.h>
+#include <linux/module.h>
+#include <linux/ethtool_netlink.h>
+
+#include "qcom.h"
+
+/* ADC threshold */
+#define QCA808X_PHY_DEBUG_ADC_THRESHOLD 0x2c80
+#define QCA808X_ADC_THRESHOLD_MASK GENMASK(7, 0)
+#define QCA808X_ADC_THRESHOLD_80MV 0
+#define QCA808X_ADC_THRESHOLD_100MV 0xf0
+#define QCA808X_ADC_THRESHOLD_200MV 0x0f
+#define QCA808X_ADC_THRESHOLD_300MV 0xff
+
+/* CLD control */
+#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7 0x8007
+#define QCA808X_8023AZ_AFE_CTRL_MASK GENMASK(8, 4)
+#define QCA808X_8023AZ_AFE_EN 0x90
+
+/* AZ control */
+#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL 0x8008
+#define QCA808X_MMD3_AZ_TRAINING_VAL 0x1c32
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB 0x8014
+#define QCA808X_MSE_THRESHOLD_20DB_VALUE 0x529
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB 0x800E
+#define QCA808X_MSE_THRESHOLD_17DB_VALUE 0x341
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB 0x801E
+#define QCA808X_MSE_THRESHOLD_27DB_VALUE 0x419
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB 0x8020
+#define QCA808X_MSE_THRESHOLD_28DB_VALUE 0x341
+
+#define QCA808X_PHY_MMD7_TOP_OPTION1 0x901c
+#define QCA808X_TOP_OPTION1_DATA 0x0
+
+#define QCA808X_PHY_MMD3_DEBUG_1 0xa100
+#define QCA808X_MMD3_DEBUG_1_VALUE 0x9203
+#define QCA808X_PHY_MMD3_DEBUG_2 0xa101
+#define QCA808X_MMD3_DEBUG_2_VALUE 0x48ad
+#define QCA808X_PHY_MMD3_DEBUG_3 0xa103
+#define QCA808X_MMD3_DEBUG_3_VALUE 0x1698
+#define QCA808X_PHY_MMD3_DEBUG_4 0xa105
+#define QCA808X_MMD3_DEBUG_4_VALUE 0x8001
+#define QCA808X_PHY_MMD3_DEBUG_5 0xa106
+#define QCA808X_MMD3_DEBUG_5_VALUE 0x1111
+#define QCA808X_PHY_MMD3_DEBUG_6 0xa011
+#define QCA808X_MMD3_DEBUG_6_VALUE 0x5f85
+
+/* master/slave seed config */
+#define QCA808X_PHY_DEBUG_LOCAL_SEED 9
+#define QCA808X_MASTER_SLAVE_SEED_ENABLE BIT(1)
+#define QCA808X_MASTER_SLAVE_SEED_CFG GENMASK(12, 2)
+#define QCA808X_MASTER_SLAVE_SEED_RANGE 0x32
+
+/* Hibernation yields lower power consumpiton in contrast with normal operation mode.
+ * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s.
+ */
+#define QCA808X_DBG_AN_TEST 0xb
+#define QCA808X_HIBERNATION_EN BIT(15)
+
+#define QCA808X_CDT_ENABLE_TEST BIT(15)
+#define QCA808X_CDT_INTER_CHECK_DIS BIT(13)
+#define QCA808X_CDT_STATUS BIT(11)
+#define QCA808X_CDT_LENGTH_UNIT BIT(10)
+
+#define QCA808X_MMD3_CDT_STATUS 0x8064
+#define QCA808X_MMD3_CDT_DIAG_PAIR_A 0x8065
+#define QCA808X_MMD3_CDT_DIAG_PAIR_B 0x8066
+#define QCA808X_MMD3_CDT_DIAG_PAIR_C 0x8067
+#define QCA808X_MMD3_CDT_DIAG_PAIR_D 0x8068
+#define QCA808X_CDT_DIAG_LENGTH_SAME_SHORT GENMASK(15, 8)
+#define QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT GENMASK(7, 0)
+
+#define QCA808X_CDT_CODE_PAIR_A GENMASK(15, 12)
+#define QCA808X_CDT_CODE_PAIR_B GENMASK(11, 8)
+#define QCA808X_CDT_CODE_PAIR_C GENMASK(7, 4)
+#define QCA808X_CDT_CODE_PAIR_D GENMASK(3, 0)
+
+#define QCA808X_CDT_STATUS_STAT_TYPE GENMASK(1, 0)
+#define QCA808X_CDT_STATUS_STAT_FAIL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 0)
+#define QCA808X_CDT_STATUS_STAT_NORMAL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 1)
+#define QCA808X_CDT_STATUS_STAT_SAME_OPEN FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 2)
+#define QCA808X_CDT_STATUS_STAT_SAME_SHORT FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 3)
+
+#define QCA808X_CDT_STATUS_STAT_MDI GENMASK(3, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI1 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 1)
+#define QCA808X_CDT_STATUS_STAT_MDI2 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI3 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 3)
+
+/* NORMAL are MDI with type set to 0 */
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI1
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+ QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+ QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI2
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+ QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+ QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI3
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+ QCA808X_CDT_STATUS_STAT_MDI3)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+ QCA808X_CDT_STATUS_STAT_MDI3)
+
+/* Added for reference of existence but should be handled by wait_for_completion already */
+#define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3))
+
+#define QCA808X_MMD7_LED_GLOBAL 0x8073
+#define QCA808X_LED_BLINK_1 GENMASK(11, 6)
+#define QCA808X_LED_BLINK_2 GENMASK(5, 0)
+/* Values are the same for both BLINK_1 and BLINK_2 */
+#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3)
+#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
+#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
+#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
+#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
+#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
+#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
+#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
+#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
+#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0)
+#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
+#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
+#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
+#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
+#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
+#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
+#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
+#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
+
+#define QCA808X_MMD7_LED2_CTRL 0x8074
+#define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075
+#define QCA808X_MMD7_LED1_CTRL 0x8076
+#define QCA808X_MMD7_LED1_FORCE_CTRL 0x8077
+#define QCA808X_MMD7_LED0_CTRL 0x8078
+#define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2))
+
+/* LED hw control pattern is the same for every LED */
+#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0)
+#define QCA808X_LED_SPEED2500_ON BIT(15)
+#define QCA808X_LED_SPEED2500_BLINK BIT(14)
+/* Follow blink trigger even if duplex or speed condition doesn't match */
+#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13)
+#define QCA808X_LED_FULL_DUPLEX_ON BIT(12)
+#define QCA808X_LED_HALF_DUPLEX_ON BIT(11)
+#define QCA808X_LED_TX_BLINK BIT(10)
+#define QCA808X_LED_RX_BLINK BIT(9)
+#define QCA808X_LED_TX_ON_10MS BIT(8)
+#define QCA808X_LED_RX_ON_10MS BIT(7)
+#define QCA808X_LED_SPEED1000_ON BIT(6)
+#define QCA808X_LED_SPEED100_ON BIT(5)
+#define QCA808X_LED_SPEED10_ON BIT(4)
+#define QCA808X_LED_COLLISION_BLINK BIT(3)
+#define QCA808X_LED_SPEED1000_BLINK BIT(2)
+#define QCA808X_LED_SPEED100_BLINK BIT(1)
+#define QCA808X_LED_SPEED10_BLINK BIT(0)
+
+#define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079
+#define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2))
+
+/* LED force ctrl is the same for every LED
+ * No documentation exist for this, not even internal one
+ * with NDA as QCOM gives only info about configuring
+ * hw control pattern rules and doesn't indicate any way
+ * to force the LED to specific mode.
+ * These define comes from reverse and testing and maybe
+ * lack of some info or some info are not entirely correct.
+ * For the basic LED control and hw control these finding
+ * are enough to support LED control in all the required APIs.
+ *
+ * On doing some comparison with implementation with qca807x,
+ * it was found that it's 1:1 equal to it and confirms all the
+ * reverse done. It was also found further specification with the
+ * force mode and the blink modes.
+ */
+#define QCA808X_LED_FORCE_EN BIT(15)
+#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13)
+#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
+#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
+#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
+#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
+
+#define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a
+/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
+ * LED to active high. It's not clear what BIT 3 and BIT 4 does.
+ */
+#define QCA808X_LED_ACTIVE_HIGH BIT(6)
+
+/* QCA808X 1G chip type */
+#define QCA808X_PHY_MMD7_CHIP_TYPE 0x901d
+#define QCA808X_PHY_CHIP_TYPE_1G BIT(0)
+
+#define QCA8081_PHY_SERDES_MMD1_FIFO_CTRL 0x9072
+#define QCA8081_PHY_FIFO_RSTN BIT(11)
+
+#define QCA8081_PHY_ID 0x004dd101
+
+MODULE_DESCRIPTION("Qualcomm Atheros QCA808X PHY driver");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_LICENSE("GPL");
+
+struct qca808x_priv {
+ int led_polarity_mode;
+};
+
+static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
+{
+ int ret;
+
+ /* Enable fast retrain */
+ ret = genphy_c45_fast_retrain(phydev, true);
+ if (ret)
+ return ret;
+
+ phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1,
+ QCA808X_TOP_OPTION1_DATA);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB,
+ QCA808X_MSE_THRESHOLD_20DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB,
+ QCA808X_MSE_THRESHOLD_17DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB,
+ QCA808X_MSE_THRESHOLD_27DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB,
+ QCA808X_MSE_THRESHOLD_28DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1,
+ QCA808X_MMD3_DEBUG_1_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4,
+ QCA808X_MMD3_DEBUG_4_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5,
+ QCA808X_MMD3_DEBUG_5_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3,
+ QCA808X_MMD3_DEBUG_3_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6,
+ QCA808X_MMD3_DEBUG_6_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2,
+ QCA808X_MMD3_DEBUG_2_VALUE);
+
+ return 0;
+}
+
+static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable)
+{
+ u16 seed_value;
+
+ if (!enable)
+ return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+ QCA808X_MASTER_SLAVE_SEED_ENABLE, 0);
+
+ seed_value = get_random_u32_below(QCA808X_MASTER_SLAVE_SEED_RANGE);
+ return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+ QCA808X_MASTER_SLAVE_SEED_CFG | QCA808X_MASTER_SLAVE_SEED_ENABLE,
+ FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value) |
+ QCA808X_MASTER_SLAVE_SEED_ENABLE);
+}
+
+static bool qca808x_is_prefer_master(struct phy_device *phydev)
+{
+ return (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_FORCE) ||
+ (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_PREFERRED);
+}
+
+static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
+{
+ return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+}
+
+static int qca808x_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct qca808x_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ /* Init LED polarity mode to -1 */
+ priv->led_polarity_mode = -1;
+
+ phydev->priv = priv;
+
+ return 0;
+}
+
+static int qca808x_config_init(struct phy_device *phydev)
+{
+ int ret;
+
+ /* Active adc&vga on 802.3az for the link 1000M and 100M */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7,
+ QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN);
+ if (ret)
+ return ret;
+
+ /* Adjust the threshold on 802.3az for the link 1000M */
+ ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
+ QCA808X_PHY_MMD3_AZ_TRAINING_CTRL,
+ QCA808X_MMD3_AZ_TRAINING_VAL);
+ if (ret)
+ return ret;
+
+ if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+ /* Config the fast retrain for the link 2500M */
+ ret = qca808x_phy_fast_retrain_config(phydev);
+ if (ret)
+ return ret;
+
+ ret = genphy_read_master_slave(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (!qca808x_is_prefer_master(phydev)) {
+ /* Enable seed and configure lower ramdom seed to make phy
+ * linked as slave mode.
+ */
+ ret = qca808x_phy_ms_seed_enable(phydev, true);
+ if (ret)
+ return ret;
+ }
+ }
+
+ /* Configure adc threshold as 100mv for the link 10M */
+ return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
+ QCA808X_ADC_THRESHOLD_MASK,
+ QCA808X_ADC_THRESHOLD_100MV);
+}
+
+static int qca808x_read_status(struct phy_device *phydev)
+{
+ struct at803x_ss_mask ss_mask = { 0 };
+ int ret;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
+ if (ret < 0)
+ return ret;
+
+ linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising,
+ ret & MDIO_AN_10GBT_STAT_LP2_5G);
+
+ ret = genphy_read_status(phydev);
+ if (ret)
+ return ret;
+
+ /* qca8081 takes the different bits for speed value from at803x */
+ ss_mask.speed_mask = QCA808X_SS_SPEED_MASK;
+ ss_mask.speed_shift = __bf_shf(QCA808X_SS_SPEED_MASK);
+ ret = at803x_read_specific_status(phydev, ss_mask);
+ if (ret < 0)
+ return ret;
+
+ if (phydev->link) {
+ if (phydev->speed == SPEED_2500)
+ phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+ else
+ phydev->interface = PHY_INTERFACE_MODE_SGMII;
+ } else {
+ /* generate seed as a lower random value to make PHY linked as SLAVE easily,
+ * except for master/slave configuration fault detected or the master mode
+ * preferred.
+ *
+ * the reason for not putting this code into the function link_change_notify is
+ * the corner case where the link partner is also the qca8081 PHY and the seed
+ * value is configured as the same value, the link can't be up and no link change
+ * occurs.
+ */
+ if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+ if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR ||
+ qca808x_is_prefer_master(phydev)) {
+ qca808x_phy_ms_seed_enable(phydev, false);
+ } else {
+ qca808x_phy_ms_seed_enable(phydev, true);
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int qca808x_soft_reset(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (qca808x_has_fast_retrain_or_slave_seed(phydev))
+ ret = qca808x_phy_ms_seed_enable(phydev, true);
+
+ return ret;
+}
+
+static bool qca808x_cdt_fault_length_valid(int cdt_code)
+{
+ switch (cdt_code) {
+ case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static int qca808x_cable_test_result_trans(int cdt_code)
+{
+ switch (cdt_code) {
+ case QCA808X_CDT_STATUS_STAT_NORMAL:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+ case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+ return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+ case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+ return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+ case QCA808X_CDT_STATUS_STAT_FAIL:
+ default:
+ return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+ }
+}
+
+static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair,
+ int result)
+{
+ int val;
+ u32 cdt_length_reg = 0;
+
+ switch (pair) {
+ case ETHTOOL_A_CABLE_PAIR_A:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A;
+ break;
+ case ETHTOOL_A_CABLE_PAIR_B:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B;
+ break;
+ case ETHTOOL_A_CABLE_PAIR_C:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C;
+ break;
+ case ETHTOOL_A_CABLE_PAIR_D:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg);
+ if (val < 0)
+ return val;
+
+ if (result == ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT)
+ val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_SAME_SHORT, val);
+ else
+ val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT, val);
+
+ return at803x_cdt_fault_length(val);
+}
+
+static int qca808x_cable_test_start(struct phy_device *phydev)
+{
+ int ret;
+
+ /* perform CDT with the following configs:
+ * 1. disable hibernation.
+ * 2. force PHY working in MDI mode.
+ * 3. for PHY working in 1000BaseT.
+ * 4. configure the threshold.
+ */
+
+ ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = at803x_config_mdix(phydev, ETH_TP_MDI);
+ if (ret < 0)
+ return ret;
+
+ /* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */
+ phydev->duplex = DUPLEX_FULL;
+ phydev->speed = SPEED_1000;
+ ret = genphy_c45_pma_setup_forced(phydev);
+ if (ret < 0)
+ return ret;
+
+ ret = genphy_setup_forced(phydev);
+ if (ret < 0)
+ return ret;
+
+ /* configure the thresholds for open, short, pair ok test */
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
+
+ return 0;
+}
+
+static int qca808x_cable_test_get_pair_status(struct phy_device *phydev, u8 pair,
+ u16 status)
+{
+ int length, result;
+ u16 pair_code;
+
+ switch (pair) {
+ case ETHTOOL_A_CABLE_PAIR_A:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, status);
+ break;
+ case ETHTOOL_A_CABLE_PAIR_B:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, status);
+ break;
+ case ETHTOOL_A_CABLE_PAIR_C:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, status);
+ break;
+ case ETHTOOL_A_CABLE_PAIR_D:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, status);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ result = qca808x_cable_test_result_trans(pair_code);
+ ethnl_cable_test_result(phydev, pair, result);
+
+ if (qca808x_cdt_fault_length_valid(pair_code)) {
+ length = qca808x_cdt_fault_length(phydev, pair, result);
+ ethnl_cable_test_fault_length(phydev, pair, length);
+ }
+
+ return 0;
+}
+
+static int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished)
+{
+ int ret, val;
+
+ *finished = false;
+
+ val = QCA808X_CDT_ENABLE_TEST |
+ QCA808X_CDT_LENGTH_UNIT;
+ ret = at803x_cdt_start(phydev, val);
+ if (ret)
+ return ret;
+
+ ret = at803x_cdt_wait_for_completion(phydev, QCA808X_CDT_ENABLE_TEST);
+ if (ret)
+ return ret;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS);
+ if (val < 0)
+ return val;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_A, val);
+ if (ret)
+ return ret;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_B, val);
+ if (ret)
+ return ret;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_C, val);
+ if (ret)
+ return ret;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_D, val);
+ if (ret)
+ return ret;
+
+ *finished = true;
+
+ return 0;
+}
+
+static int qca808x_get_features(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_c45_pma_read_abilities(phydev);
+ if (ret)
+ return ret;
+
+ /* The autoneg ability is not existed in bit3 of MMD7.1,
+ * but it is supported by qca808x PHY, so we add it here
+ * manually.
+ */
+ linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
+
+ /* As for the qca8081 1G version chip, the 2500baseT ability is also
+ * existed in the bit0 of MMD1.21, we need to remove it manually if
+ * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
+ */
+ ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
+ if (ret < 0)
+ return ret;
+
+ if (QCA808X_PHY_CHIP_TYPE_1G & ret)
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+
+ return 0;
+}
+
+static int qca808x_config_aneg(struct phy_device *phydev)
+{
+ int phy_ctrl = 0;
+ int ret;
+
+ ret = at803x_prepare_config_aneg(phydev);
+ if (ret)
+ return ret;
+
+ /* The reg MII_BMCR also needs to be configured for force mode, the
+ * genphy_config_aneg is also needed.
+ */
+ if (phydev->autoneg == AUTONEG_DISABLE)
+ genphy_c45_pma_setup_forced(phydev);
+
+ if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising))
+ phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G;
+
+ ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
+ MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl);
+ if (ret < 0)
+ return ret;
+
+ return __genphy_config_aneg(phydev, ret);
+}
+
+static void qca808x_link_change_notify(struct phy_device *phydev)
+{
+ /* Assert interface sgmii fifo on link down, deassert it on link up,
+ * the interface device address is always phy address added by 1.
+ */
+ mdiobus_c45_modify_changed(phydev->mdio.bus, phydev->mdio.addr + 1,
+ MDIO_MMD_PMAPMD, QCA8081_PHY_SERDES_MMD1_FIFO_CTRL,
+ QCA8081_PHY_FIFO_RSTN,
+ phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
+}
+
+static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
+ u16 *offload_trigger)
+{
+ /* Parsing specific to netdev trigger */
+ if (test_bit(TRIGGER_NETDEV_TX, &rules))
+ *offload_trigger |= QCA808X_LED_TX_BLINK;
+ if (test_bit(TRIGGER_NETDEV_RX, &rules))
+ *offload_trigger |= QCA808X_LED_RX_BLINK;
+ if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED10_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED100_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED1000_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED2500_ON;
+ if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+ *offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
+ if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+ *offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
+
+ if (rules && !*offload_trigger)
+ return -EOPNOTSUPP;
+
+ /* Enable BLINK_CHECK_BYPASS by default to make the LED
+ * blink even with duplex or speed mode not enabled.
+ */
+ *offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
+
+ return 0;
+}
+
+static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 offload_trigger = 0;
+
+ if (index > 2)
+ return -EINVAL;
+
+ return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+}
+
+static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 reg, offload_trigger = 0;
+ int ret;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+ if (ret)
+ return ret;
+
+ ret = qca808x_led_hw_control_enable(phydev, index);
+ if (ret)
+ return ret;
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_PATTERN_MASK,
+ offload_trigger);
+}
+
+static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+ int val;
+
+ if (index > 2)
+ return false;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+
+ return !(val & QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
+ unsigned long *rules)
+{
+ u16 reg;
+ int val;
+
+ if (index > 2)
+ return -EINVAL;
+
+ /* Check if we have hw control enabled */
+ if (qca808x_led_hw_control_status(phydev, index))
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+ if (val & QCA808X_LED_TX_BLINK)
+ set_bit(TRIGGER_NETDEV_TX, rules);
+ if (val & QCA808X_LED_RX_BLINK)
+ set_bit(TRIGGER_NETDEV_RX, rules);
+ if (val & QCA808X_LED_SPEED10_ON)
+ set_bit(TRIGGER_NETDEV_LINK_10, rules);
+ if (val & QCA808X_LED_SPEED100_ON)
+ set_bit(TRIGGER_NETDEV_LINK_100, rules);
+ if (val & QCA808X_LED_SPEED1000_ON)
+ set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+ if (val & QCA808X_LED_SPEED2500_ON)
+ set_bit(TRIGGER_NETDEV_LINK_2500, rules);
+ if (val & QCA808X_LED_HALF_DUPLEX_ON)
+ set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+ if (val & QCA808X_LED_FULL_DUPLEX_ON)
+ set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+
+ return 0;
+}
+
+static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_PATTERN_MASK);
+}
+
+static int qca808x_led_brightness_set(struct phy_device *phydev,
+ u8 index, enum led_brightness value)
+{
+ u16 reg;
+ int ret;
+
+ if (index > 2)
+ return -EINVAL;
+
+ if (!value) {
+ ret = qca808x_led_hw_control_reset(phydev, index);
+ if (ret)
+ return ret;
+ }
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+ QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON :
+ QCA808X_LED_FORCE_OFF);
+}
+
+static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ int ret;
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ /* Set blink to 50% off, 50% on at 4Hz by default */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
+ QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
+ QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
+ if (ret)
+ return ret;
+
+ /* We use BLINK_1 for normal blinking */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
+ if (ret)
+ return ret;
+
+ /* We set blink to 4Hz, aka 250ms */
+ *delay_on = 250 / 2;
+ *delay_off = 250 / 2;
+
+ return 0;
+}
+
+static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
+ unsigned long modes)
+{
+ struct qca808x_priv *priv = phydev->priv;
+ bool active_low = false;
+ u32 mode;
+
+ for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
+ switch (mode) {
+ case PHY_LED_ACTIVE_LOW:
+ active_low = true;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+
+ /* PHY polarity is global and can't be set per LED.
+ * To detect this, check if last requested polarity mode
+ * match the new one.
+ */
+ if (priv->led_polarity_mode >= 0 &&
+ priv->led_polarity_mode != active_low) {
+ phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
+ return -EINVAL;
+ }
+
+ /* Save the last PHY polarity mode */
+ priv->led_polarity_mode = active_low;
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN,
+ QCA808X_MMD7_LED_POLARITY_CTRL,
+ QCA808X_LED_ACTIVE_HIGH,
+ active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
+}
+
+static struct phy_driver qca808x_driver[] = {
+{
+ /* Qualcomm QCA8081 */
+ PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
+ .name = "Qualcomm QCA8081",
+ .flags = PHY_POLL_CABLE_TEST,
+ .probe = qca808x_probe,
+ .config_intr = at803x_config_intr,
+ .handle_interrupt = at803x_handle_interrupt,
+ .get_tunable = at803x_get_tunable,
+ .set_tunable = at803x_set_tunable,
+ .set_wol = at803x_set_wol,
+ .get_wol = at803x_get_wol,
+ .get_features = qca808x_get_features,
+ .config_aneg = qca808x_config_aneg,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .read_status = qca808x_read_status,
+ .config_init = qca808x_config_init,
+ .soft_reset = qca808x_soft_reset,
+ .cable_test_start = qca808x_cable_test_start,
+ .cable_test_get_status = qca808x_cable_test_get_status,
+ .link_change_notify = qca808x_link_change_notify,
+ .led_brightness_set = qca808x_led_brightness_set,
+ .led_blink_set = qca808x_led_blink_set,
+ .led_hw_is_supported = qca808x_led_hw_is_supported,
+ .led_hw_control_set = qca808x_led_hw_control_set,
+ .led_hw_control_get = qca808x_led_hw_control_get,
+ .led_polarity_set = qca808x_led_polarity_set,
+}, };
+
+module_phy_driver(qca808x_driver);
+
+static struct mdio_device_id __maybe_unused qca808x_tbl[] = {
+ { PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, qca808x_tbl);
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [net-next PATCH v4 0/5] net: phy: split at803x
2024-01-29 14:15 [net-next PATCH v4 0/5] net: phy: split at803x Christian Marangi
` (4 preceding siblings ...)
2024-01-29 14:15 ` [net-next PATCH v4 5/5] net: phy: qcom: detach qca808x PHY driver from at803x Christian Marangi
@ 2024-02-01 0:40 ` patchwork-bot+netdevbpf
5 siblings, 0 replies; 7+ messages in thread
From: patchwork-bot+netdevbpf @ 2024-02-01 0:40 UTC (permalink / raw)
To: Christian Marangi
Cc: andrew, hkallweit1, linux, davem, edumazet, kuba, pabeni,
andersson, konrad.dybcio, linux-kernel, netdev, linux-arm-msm
Hello:
This series was applied to netdev/net-next.git (main)
by Jakub Kicinski <kuba@kernel.org>:
On Mon, 29 Jan 2024 15:15:18 +0100 you wrote:
> This is the last patchset of a long series of cleanup and
> preparation to make at803x better maintainable and permit
> the addition of other QCOM PHY Families.
>
> A shared library modules is created since many QCOM PHY share
> similar/exact implementation and are reused.
>
> [...]
Here is the summary with links:
- [net-next,v4,1/5] net: phy: move at803x PHY driver to dedicated directory
https://git.kernel.org/netdev/net-next/c/9e56ff53b411
- [net-next,v4,2/5] net: phy: qcom: create and move functions to shared library
https://git.kernel.org/netdev/net-next/c/6fb760972c49
- [net-next,v4,3/5] net: phy: qcom: deatch qca83xx PHY driver from at803x
https://git.kernel.org/netdev/net-next/c/2e45d404d99d
- [net-next,v4,4/5] net: phy: qcom: move additional functions to shared library
https://git.kernel.org/netdev/net-next/c/249d2b80e4db
- [net-next,v4,5/5] net: phy: qcom: detach qca808x PHY driver from at803x
https://git.kernel.org/netdev/net-next/c/c89414adf2ec
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
^ permalink raw reply [flat|nested] 7+ messages in thread