From: Vikram Sharma <quic_vikramsa@quicinc.com>
To: <rfoss@kernel.org>, <todor.too@gmail.com>,
<bryan.odonoghue@linaro.org>, <mchehab@kernel.org>,
<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<akapatra@quicinc.com>, <hariramp@quicinc.com>,
<andersson@kernel.org>, <konradybcio@kernel.org>,
<hverkuil-cisco@xs4all.nl>, <cros-qcom-dts-watchers@chromium.org>,
<catalin.marinas@arm.com>, <will@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<quic_vikramsa@quicinc.com>, <linux-media@vger.kernel.org>,
<linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <kernel@quicinc.com>
Subject: [PATCH v6 5/5] arm64: dts: qcom: qcs6490-rb3gen2-vision-mezzanine: Add vision mezzanine
Date: Wed, 27 Nov 2024 15:34:21 +0530 [thread overview]
Message-ID: <20241127100421.3447601-6-quic_vikramsa@quicinc.com> (raw)
In-Reply-To: <20241127100421.3447601-1-quic_vikramsa@quicinc.com>
The Vision Mezzanine for the RB3 ships with an imx577 camera sensor.
Enable the IMX577 on the vision mezzanine.
An example media-ctl pipeline for the imx577 is:
media-ctl --reset
media-ctl -v -V '"imx577 '19-001a'":0[fmt:SRGGB10/4056x3040 field:none]'
media-ctl -V '"msm_csiphy3":0[fmt:SRGGB10/4056x3040]'
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4056x3040]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4056x3040]'
media-ctl -l '"msm_csiphy3":1->"msm_csid0":0[1]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 4056x3040 -F /dev/video0
Signed-off-by: Hariram Purushothaman <quic_hariramp@quicinc.com>
Signed-off-by: Vikram Sharma <quic_vikramsa@quicinc.com>
Signed-off-by: Trishansh Bhardwaj <quic_tbhardwa@quicinc.com>
---
arch/arm64/boot/dts/qcom/Makefile | 4 +
.../qcs6490-rb3gen2-vision-mezzanine.dtso | 108 ++++++++++++++++++
2 files changed, 112 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qcs6490-rb3gen2-vision-mezzanine.dtso
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 9bb8b191aeb5..4ee57b3871dd 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -114,6 +114,10 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
+
+qcs6490-rb3gen2-vision-mezzanine-dtbs := qcs6490-rb3gen2.dtb qcs6490-rb3gen2-vision-mezzanine.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2-vision-mezzanine.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2-vision-mezzanine.dtso b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2-vision-mezzanine.dtso
new file mode 100644
index 000000000000..6e2fccca8f11
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2-vision-mezzanine.dtso
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/*
+ * Camera Sensor overlay on top of rb3gen2 core kit.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/qcom,camcc-sc7280.h>
+
+/dts-v1/;
+/plugin/;
+
+&camcc {
+ status = "okay";
+};
+
+&camss {
+ vdda-phy-supply = <&vreg_l10c_0p88>;
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* The port index denotes CSIPHY id i.e. csiphy3 */
+ port@3 {
+ reg = <3>;
+ csiphy3_ep: endpoint {
+ clock-lanes = <7>;
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&imx577_ep>;
+ };
+ };
+ };
+};
+
+&cci1 {
+ status = "okay";
+};
+
+&cci1_i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera@1a {
+ compatible = "sony,imx577";
+ reg = <0x1a>;
+
+ reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "suspend";
+ pinctrl-0 = <&cam2_default>;
+ pinctrl-1 = <&cam2_suspend>;
+
+ clocks = <&camcc CAM_CC_MCLK3_CLK>;
+ assigned-clocks = <&camcc CAM_CC_MCLK3_CLK>;
+ assigned-clock-rates = <24000000>;
+
+ dovdd-supply = <&vreg_l18b_1p8>;
+
+ port {
+ imx577_ep: endpoint {
+ clock-lanes = <7>;
+ link-frequencies = /bits/ 64 <600000000>;
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&csiphy3_ep>;
+ };
+ };
+ };
+};
+
+&tlmm {
+ cam2_default: cam2-default-state {
+ rst-pins {
+ pins = "gpio78";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ mclk-pins {
+ pins = "gpio67";
+ function = "cam_mclk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ cam2_suspend: cam2-suspend-state {
+ rst-pins {
+ pins = "gpio78";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ output-low;
+ };
+
+ mclk-pins {
+ pins = "gpio67";
+ function = "cam_mclk";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+};
--
2.25.1
next prev parent reply other threads:[~2024-11-27 10:05 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-11-27 10:04 [PATCH v6 0/5] media: qcom: camss: Add sc7280 support Vikram Sharma
2024-11-27 10:04 ` [PATCH v6 1/5] media: dt-bindings: Add qcom,sc7280-camss Vikram Sharma
2024-11-27 12:57 ` Vladimir Zapolskiy
2024-11-27 23:31 ` Bryan O'Donoghue
2024-11-28 8:54 ` Vladimir Zapolskiy
[not found] ` <af043a60-adac-41da-8c7c-1ae5272ffeb1@quicinc.com>
2024-11-28 10:09 ` Krzysztof Kozlowski
2024-11-27 10:04 ` [PATCH v6 2/5] media: qcom: camss: Sort camss version enums and compatible strings Vikram Sharma
2024-11-27 10:04 ` [PATCH v6 3/5] media: qcom: camss: Add support for camss driver on sc7280 Vikram Sharma
2024-11-27 10:04 ` [PATCH v6 4/5] arm64: dts: qcom: sc7280: Add support for camss Vikram Sharma
2024-11-27 18:32 ` Krzysztof Kozlowski
2024-11-27 18:38 ` Krzysztof Kozlowski
[not found] ` <993cea98-24bc-4f86-835f-099c5009c3b8@quicinc.com>
2024-11-28 7:04 ` Krzysztof Kozlowski
2024-11-27 10:04 ` Vikram Sharma [this message]
2024-11-27 10:26 ` [PATCH v6 5/5] arm64: dts: qcom: qcs6490-rb3gen2-vision-mezzanine: Add vision mezzanine Bryan O'Donoghue
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20241127100421.3447601-6-quic_vikramsa@quicinc.com \
--to=quic_vikramsa@quicinc.com \
--cc=akapatra@quicinc.com \
--cc=andersson@kernel.org \
--cc=bryan.odonoghue@linaro.org \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=cros-qcom-dts-watchers@chromium.org \
--cc=devicetree@vger.kernel.org \
--cc=hariramp@quicinc.com \
--cc=hverkuil-cisco@xs4all.nl \
--cc=kernel@quicinc.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=rfoss@kernel.org \
--cc=robh@kernel.org \
--cc=todor.too@gmail.com \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox