[PATCH RFC/WIP 3/4] arm64: dts: qcom: sm8750-mtp: Enable USB headset and Type-C altmode

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

MTP8750 does not have audio jack connected and relies on USB mux
(WCD9395).  Add necessary nodes for proper audio headset support along
with USB Type-C altmode and orientation.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8750-mtp.dts | 58 +++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8750-mtp.dts b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
index bd0918e8a7a7e03530eea577c7609454fecfdaf7..c3470e1daa6b7f31196645759be23fb168ce8eb7 100644
--- a/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
@@ -53,6 +53,15 @@ wcd939x: audio-codec {
 		vdd-mic-bias-supply = <&vreg_bob1>;
 
 		#sound-dai-cells = <1>;
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			wcd_codec_headset_in: endpoint {
+				remote-endpoint = <&wcd_usbss_headset_out>;
+			};
+		};
 	};
 
 	chosen {
@@ -220,6 +229,14 @@ port@1 {
 					pmic_glink_ss_in: endpoint {
 					};
 				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&wcd_usbss_sbu_mux>;
+					};
+				};
 			};
 		};
 	};
@@ -845,6 +862,42 @@ vreg_l7n_3p3: ldo7 {
 	};
 };
 
+&i2c3 {
+	status = "okay";
+
+	wcd_usbss: typec-mux@e {
+		compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss";
+		reg = <0xe>;
+
+		vdd-supply = <&vreg_l15b_1p8>;
+		reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
+
+		mode-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				wcd_usbss_sbu_mux: endpoint {
+					remote-endpoint = <&pmic_glink_sbu>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				wcd_usbss_headset_out: endpoint {
+					remote-endpoint = <&wcd_codec_headset_in>;
+				};
+			};
+		};
+	};
+};
+
 &lpass_vamacro {
 	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
 	pinctrl-names = "default";
@@ -973,6 +1026,11 @@ &pmih0108_eusb2_repeater {
 	vdd3-supply = <&vreg_l5b_3p1>;
 };
 
+&qup_i2c3_data_clk {
+	/* Use internal I2C pull-up */
+	bias-pull-up = <2200>;
+};
+
 &qupv3_1 {
 	status = "okay";
 };

-- 
2.45.2