[PATCH WIP v2 0/8] media: camss: Add support for C-PHY configuration on Qualcomm platforms

[David Heidelberg via B4 Relay <devnull+david.ixit.cz@kernel.org>]

# Short summary

This patch series extends the Qualcomm CAMSS (Camera Subsystem),
including CSID and CSIPHY components, to support C-PHY mode configuration.

# Background and motivation

Modern smartphone cameras increasingly rely on MIPI C-PHY rather than D-PHY,
thanks to its higher data throughput and signal efficiency. As a result,
many OEMs adopt C-PHY interfaces for main (rear) cameras on Qualcomm-based
devices.

Until now, mainline Linux lacked C-PHY configuration support for Qualcomm
chipsets, preventing bring-up of primary camera sensors on several
Snapdragon platforms. This series closes that gap.

 - Introduces C-PHY configuration support for the CAMSS driver stack,
   covering both CSID and CSIPHY blocks.
 - Successfully enables C-PHY operation on the Snapdragon 845 platform.
 - Tested on OnePlus 6 and 6T phones running mainline Linux,
   using the Sony IMX519 main camera sensor.
 - The new configuration allows other chipsets versionsto enable C-PHY by
   simply adding corresponding sensor driver support and csiphy
   initialization data, following the example set for sdm845.

With this patch series, mainline Linux gains working C-PHY support for
Snapdragon 845, paving the way for improved main camera functionality
across many Qualcomm-based devices. The groundwork also simplifies
future enablement efforts for additional SoCs and sensors.

Until merged, the series will be also available at:
  https://gitlab.com/sdm845/sdm845-next/-/commits/b4/qcom-cphy

Signed-off-by: David Heidelberg <david@ixit.cz>
---
Changes in v2:
- [NOTE] This is still WIP patch series, thus I wanted to publish already
  changed parts to get feedback regarding to the direction of patchset.  [/NOTE]
- When switch to using odd bits, zeroed val which was left unitialized in v1.
- Accidentally missed archs added back in the commit moving lane regs to
  new location.
- Remove commit with reverting check for only D-PHY is supported and
  adjusted the check to also account for C-PHY.
- Documented link frequency calculation with defines. (Casey)
- Changed the cphy boolean to phy_cfg enum in the camss/camss-csiphy.
  (Brian)
- Added patch for csiphy-3ph enablement for sm7280 from Luca as I'm
  meanwhile trying to bring up the C-PHY sensor on FairPhone 5.
- Merged these two commits together
    csiphy-3ph: Enable sdm845 C-PHY sequence
    csiphy-3ph: Add Gen2 v1.1 MIPI CSI-2 CPHY init
  merged R-b.
- Link to v1: https://lore.kernel.org/r/20251109-qcom-cphy-v1-0-165f7e79b0e1@ixit.cz

---
Casey Connolly (1):
      media: qcom: camss: csiphy-3ph: Add Gen2 v1.1 MIPI CSI-2 CPHY init

David Heidelberg (5):
      media: qcom: camss: csiphy: Introduce PHY configuration
      media: qcom: camss: csiphy-3ph: Use odd bits for configuring C-PHY lanes
      media: qcom: camss: Prepare CSID for C-PHY support
      media: qcom: camss: csiphy-3ph: C-PHY needs own lane configuration
      media: qcom: camss: Account for C-PHY when calculating link frequency

Luca Weiss (1):
      media: qcom: camss: csiphy-3ph: Add Gen2 v1.2.1 MIPI CSI-2 C-PHY init

Petr Hodina (1):
      media: qcom: camss: Initialize lanes after lane configuration is available

 .../media/platform/qcom/camss/camss-csid-gen2.c    |   1 +
 drivers/media/platform/qcom/camss/camss-csid.c     |   3 +-
 drivers/media/platform/qcom/camss/camss-csid.h     |   1 +
 .../platform/qcom/camss/camss-csiphy-3ph-1-0.c     | 318 ++++++++++++++++++---
 drivers/media/platform/qcom/camss/camss-csiphy.c   |   6 +-
 drivers/media/platform/qcom/camss/camss-csiphy.h   |   2 +
 drivers/media/platform/qcom/camss/camss.c          |  34 ++-
 drivers/media/platform/qcom/camss/camss.h          |   2 +-
 8 files changed, 312 insertions(+), 55 deletions(-)
---
base-commit: bc04acf4aeca588496124a6cf54bfce3db327039
change-id: 20251109-qcom-cphy-bb8cbda1c644

Best regards,
-- 
David Heidelberg <david@ixit.cz>