Re: [PATCH v2 3/4] drm/msm/a6xx: Get HBB dynamically, if available

[Akhil P Oommen <quic_akhilpo@quicinc.com>]

On 4/10/2025 11:13 PM, Konrad Dybcio wrote:
> From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> 
> The Highest Bank address Bit value can change based on memory type used.
> 
> Attempt to retrieve it dynamically, and fall back to a reasonable
> default (the one used prior to this change) on error.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> ---
>  drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 15 ++++++++++++++-
>  1 file changed, 14 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/gpu/drm/msm/adreno/a6xx_gpu.c b/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
> index 06465bc2d0b4b128cddfcfcaf1fe4252632b6777..a6232b382bd16319f20ae5f8f5e57f38ecc62d9f 100644
> --- a/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
> +++ b/drivers/gpu/drm/msm/adreno/a6xx_gpu.c
> @@ -13,6 +13,7 @@
>  #include <linux/firmware/qcom/qcom_scm.h>
>  #include <linux/pm_domain.h>
>  #include <linux/soc/qcom/llcc-qcom.h>
> +#include <linux/soc/qcom/smem.h>
>  
>  #define GPU_PAS_ID 13
>  
> @@ -587,6 +588,8 @@ static void a6xx_set_cp_protect(struct msm_gpu *gpu)
>  
>  static void a6xx_calc_ubwc_config(struct adreno_gpu *gpu)
>  {
> +	int hbb;
> +
>  	gpu->ubwc_config.rgb565_predicator = 0;
>  	gpu->ubwc_config.uavflagprd_inv = 0;
>  	gpu->ubwc_config.min_acc_len = 0;
> @@ -635,7 +638,6 @@ static void a6xx_calc_ubwc_config(struct adreno_gpu *gpu)
>  	    adreno_is_a690(gpu) ||
>  	    adreno_is_a730(gpu) ||
>  	    adreno_is_a740_family(gpu)) {
> -		/* TODO: get ddr type from bootloader and use 2 for LPDDR4 */
>  		gpu->ubwc_config.highest_bank_bit = 16;
>  		gpu->ubwc_config.amsbc = 1;
>  		gpu->ubwc_config.rgb565_predicator = 1;
> @@ -664,6 +666,13 @@ static void a6xx_calc_ubwc_config(struct adreno_gpu *gpu)
>  		gpu->ubwc_config.highest_bank_bit = 14;
>  		gpu->ubwc_config.min_acc_len = 1;
>  	}
> +
> +	/* Attempt to retrieve the data from SMEM, keep the above defaults in case of error */
> +	hbb = qcom_smem_dram_get_hbb();
> +	if (hbb < 0)
> +		return;
> +
> +	gpu->ubwc_config.highest_bank_bit = hbb;

I am worried about blindly relying on SMEM data directly for HBB for
legacy chipsets. There is no guarantee it is accurate on every chipset
and every version of firmware. Also, until recently, this value was
hardcoded in Mesa which matched the value in KMD. So it is better to
make this opt in, for newer chipsets or those which somebody can verify.
We can invert this logic to something like this:

if (!gpu->ubwc_config.highest_bank_bit)
    gpu->ubwc_config.highest_bank_bit = qcom_smem_dram_get_hbb();

>  }
>  
>  static void a6xx_set_ubwc_config(struct msm_gpu *gpu)
> @@ -2467,6 +2476,10 @@ struct msm_gpu *a6xx_gpu_init(struct drm_device *dev)
>  	bool is_a7xx;
>  	int ret;
>  
> +	/* We need data from SMEM to retrieve HBB in calc_ubwc_config() */
> +	if (!qcom_smem_is_available())
> +		return ERR_PTR(-EPROBE_DEFER);
> +

We should add "depends on QCOM_SMEM" to Kconfig. Is SMEM device present
in all Qcom SoC devicetrees? I wonder if there is a scenario where there
might be an infinite EPROBE_DEFER here.

-Akhil.

>  	a6xx_gpu = kzalloc(sizeof(*a6xx_gpu), GFP_KERNEL);
>  	if (!a6xx_gpu)
>  		return ERR_PTR(-ENOMEM);
>