Linux ARM-MSM sub-architecture
 help / color / mirror / Atom feed
From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: Neil Armstrong <neil.armstrong@linaro.org>,
	Bjorn Andersson <andersson@kernel.org>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Subject: Re: [PATCH v5] arch: arm64: dts: sm8650-hdk: add support for the Display Card overlay
Date: Thu, 6 Jun 2024 12:38:41 +0200	[thread overview]
Message-ID: <2fa9d6e5-d301-4226-aef8-6d691cd392fa@linaro.org> (raw)
In-Reply-To: <20240606-topic-sm8650-upstream-hdk-v5-1-5d878f3047e3@linaro.org>

On 6.06.2024 10:16 AM, Neil Armstrong wrote:
> With the SM8650-HDK, a Display Card kit can be connected to provide
> a VTDR6130 display with Goodix Berlin Touch controller.
> 
> In order to route the DSI lanes to the connector for the Display
> Card kit, a switch must be changed on the board.
> 
> The HDMI nodes are disabled since the DSI lanes are shared with
> the DSI to HDMI transceiver.
> 
> Add support for this card as an overlay and apply it it at
> build-time to the sm8650-hdk dtb.
> 
> Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
> Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---

[...]

> +

/* Disable HDMI bridge related nodes (mutually exclusive with the display card) */
> +&i2c6 {
> +	status = "disabled";
> +};
> +
> +&lt9611_1v2 {
> +	status = "disabled";
> +};
> +
> +&lt9611_3v3 {
> +	status = "disabled";
> +};
> +
> +&vreg_bob_3v3 {
> +	status = "disabled";
> +};
> +
> +&lt9611_codec {
> +	status = "disabled";
> +};
> +
> +&mdss_dsi0 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	panel@0 {
> +		compatible = "visionox,vtdr6130";
> +		reg = <0>;
> +
> +		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
> +
> +		vddio-supply = <&vreg_l12b_1p8>;
> +		vci-supply = <&vreg_l13b_3p0>;
> +		vdd-supply = <&vreg_l11b_1p2>;
> +
> +		pinctrl-0 = <&disp0_reset_n_active>, <&mdp_vsync>;
> +		pinctrl-1 = <&disp0_reset_n_suspend>, <&mdp_vsync>;
> +		pinctrl-names = "default", "sleep";
> +
> +		port {
> +			panel0_in: endpoint {
> +				remote-endpoint = <&mdss_dsi0_out>;
> +			};
> +		};
> +	};
> +
> +	/*
> +	 * DTC requires to have both endpoints when compiling the overlay
> +	 * and also requires the #address/size-cells + reg properties
> +	 */

[...]

> +	/* DTC requires the #address/size-cells to compile DTBO */

I think we can leave out such comments, if somebody tries to "clean it up",
dtc will scream

with that:

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

      reply	other threads:[~2024-06-06 10:38 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-06-06  8:16 [PATCH v5] arch: arm64: dts: sm8650-hdk: add support for the Display Card overlay Neil Armstrong
2024-06-06 10:38 ` Konrad Dybcio [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=2fa9d6e5-d301-4226-aef8-6d691cd392fa@linaro.org \
    --to=konrad.dybcio@linaro.org \
    --cc=andersson@kernel.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=neil.armstrong@linaro.org \
    --cc=robh@kernel.org \
    --cc=vladimir.zapolskiy@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox