Re: [PATCH v4 3/5] net: mdio: ipq4019: configure CMN PLL clock for ipq5332

[Jie Luo <quic_luoj@quicinc.com>]

On 1/3/2024 5:50 PM, Bryan O'Donoghue wrote:
> On 25/12/2023 08:44, Luo Jie wrote:
>> The reference clock of CMN PLL block is selectable, the internal
>> 48MHZ is used by default.
>>
>> The output clock of CMN PLL block is for providing the clock
>> source of ethernet device(such as qca8084), there are 1 * 25MHZ
>> and 3 * 50MHZ output clocks available for the ethernet devices.
>>
>> Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
>> ---
>>   drivers/net/mdio/mdio-ipq4019.c | 129 +++++++++++++++++++++++++++++++-
>>   1 file changed, 128 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/net/mdio/mdio-ipq4019.c 
>> b/drivers/net/mdio/mdio-ipq4019.c
>> index e24b0e688b10..e4862ac02026 100644
>> --- a/drivers/net/mdio/mdio-ipq4019.c
>> +++ b/drivers/net/mdio/mdio-ipq4019.c
>> @@ -44,6 +44,17 @@
>>   /* Maximum SOC PCS(uniphy) number on IPQ platform */
>>   #define ETH_LDO_RDY_CNT                3
>> +#define CMN_PLL_REFERENCE_SOURCE_SEL        0x28
>> +#define CMN_PLL_REFCLK_SOURCE_DIV        GENMASK(9, 8)
>> +
>> +#define CMN_PLL_REFERENCE_CLOCK            0x784
>> +#define CMN_PLL_REFCLK_EXTERNAL            BIT(9)
>> +#define CMN_PLL_REFCLK_DIV            GENMASK(8, 4)
>> +#define CMN_PLL_REFCLK_INDEX            GENMASK(3, 0)
>> +
>> +#define CMN_PLL_POWER_ON_AND_RESET        0x780
>> +#define CMN_ANA_EN_SW_RSTN            BIT(6)
>> +
>>   enum mdio_clk_id {
>>       MDIO_CLK_MDIO_AHB,
>>       MDIO_CLK_UNIPHY0_AHB,
>> @@ -55,6 +66,7 @@ enum mdio_clk_id {
>>   struct ipq4019_mdio_data {
>>       void __iomem *membase;
>> +    void __iomem *cmn_membase;
>>       void __iomem *eth_ldo_rdy[ETH_LDO_RDY_CNT];
>>       struct clk *clk[MDIO_CLK_CNT];
>>   };
>> @@ -227,12 +239,116 @@ static int ipq4019_mdio_write_c22(struct 
>> mii_bus *bus, int mii_id, int regnum,
>>       return 0;
>>   }
>> +/* For the CMN PLL block, the reference clock can be configured 
>> according to
>> + * the device tree property "qcom,cmn-ref-clock-frequency", the 
>> internal 48MHZ
>> + * is used by default.
>> + *
>> + * The output clock of CMN PLL block is provided to the ethernet 
>> devices,
>> + * threre are 4 CMN PLL output clocks (1*25MHZ + 3*50MHZ) enabled by 
>> default.
>> + *
>> + * Such as the output 50M clock for the qca8084 ethernet PHY.
>> + */
>> +static int ipq_cmn_clock_config(struct mii_bus *bus)
>> +{
>> +    struct ipq4019_mdio_data *priv;
>> +    u32 reg_val, src_sel, ref_clk;
>> +    int ret;
>> +
>> +    priv = bus->priv;
>> +    if (priv->cmn_membase) {
> 
> if (!priv->cnm_membase)
>      return 0;
> 
> then move the indentation here one tab left.
> 
Ok, will update this, Thanks.

> ---
> bod