Re: [PATCH v4 3/6] arm64: dts: qcom: Add AYN QCS8550 Common

[Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>]

On 3/30/26 1:00 PM, Konrad Dybcio wrote:
> On 3/27/26 10:26 PM, Aaron Kling wrote:
>> On Tue, Mar 24, 2026 at 7:36 AM Konrad Dybcio
>> <konrad.dybcio@oss.qualcomm.com> wrote:
>>>
>>> On 3/23/26 5:27 PM, Aaron Kling via B4 Relay wrote:
>>>> From: Teguh Sobirin <teguh@sobir.in>
>>>>
>>>> This contains everything common between the AYN QCS8550 devices. It will
>>>> be included by device specific dts'.
>>>>
>>>> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
>>>> Co-developed-by: Aaron Kling <webgeek1234@gmail.com>
>>>> Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
>>>> ---
>>>
>>> [...]
>>>
>>>> +     sound {
>>>> +             compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
>>>> +             pinctrl-0 = <&lpi_i2s3_active>;
>>>> +             pinctrl-names = "default";
>>>> +
>>>> +             model = "AYN-Odin2";
>>>
>>> Is this enough of a distinction? Do you need to make any changes to the
>>> one with a HDMI bridge to get HDMI audio?
>>
>> After this quesstion, I tried to verify hdmi and am unable to even get
>> the connector to come up. The lt8912b driver complains that the
>> connector doesn't support edid read. Which per the current connector
>> node is correct, none of the devices list a ddc node. I am trying to
>> investigate this further, but vendor source release unfortunately
>> appears to be missing pieces related to this. And no other current
>> qcom device uses this bridge to take a guess at which controller the
>> ddc is on.
> 
> Go through the I2C buses that are enabled on the vendor kernel and try
> inspecting them with toos like i2cdetect
> 
>>
>> On a related note, I'm not sure hdmi is covered in the audio topology.
> 
> Since this is a DSI bridge, I'd imagine it needs a separate connection
> to the SoC's sound hardware. We've had similar occurences in the past,
> e.g. this on the SM8250 RB5 board (qrb5165-rb5.dts):
> 
> https://github.com/alsa-project/alsa-ucm-conf/blob/master/ucm2/Qualcomm/sm8250/HDMI.conf
> 
> Maybe +Dmitry could help you out

(mentions work better when you actually add the people you intended to
- fixing that)

> 
> Konrad
> 
>> What I'm using is here [0]. This is in a fork of the topology repo
>> with aosp build rules added. Speakers work, headphones out and in
>> work. DP works only with the pending q6dsp fixups series, which I
>> should probably narrow down and ask for a 6.18 backport for. The ucm
>> config [1] I'm basing tests on doesn't handle the built-in mic and I
>> haven't been able to figure that out yet, so that's also unknown.
>>
>> Aaron
>>
>> [0] https://github.com/LineageOS/android_hardware_qcom_audioreach-topology/blob/ad67f3777b1d4dec5289bc7117f2ec34521be7e6/AYN-Odin2.m4
>> [1] https://github.com/AYNTechnologies/alsa-ucm-conf/commit/d33738b93e9560e8d9e08a024cc84c8055bb7eb9