From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: Marijn Suijten <marijn.suijten@somainline.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Bjorn Andersson <andersson@kernel.org>,
Andy Gross <agross@kernel.org>,
linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org
Subject: Re: [PATCH 4/4] arm64: dts: qcom: sm8350-nagara: Unify status property placement
Date: Mon, 3 Apr 2023 12:17:38 +0200 [thread overview]
Message-ID: <97316d33-29b9-700f-8766-df538b133f35@linaro.org> (raw)
In-Reply-To: <i5tsdvn45peivo7tegmg3q4mhsz2ly2kfs64kezeykn2bbosd5@ugfqrjqumljd>
On 2.04.2023 17:19, Marijn Suijten wrote:
> On 2023-03-21 23:12:31, Konrad Dybcio wrote:
>
> When you get to resending this, change sm8350-nagara in the title to
> sm8350-sagami :)
Even I confuse them, they just look too alike! ;)
Konrad
>
> - Marijn
>
>> As we're heading towards getting the status property last everywhere,
>> take care of it for SM8350 SONY Sagami.
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>> .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi | 30 ++++++++++------------
>> 1 file changed, 14 insertions(+), 16 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
>> index b2baa81baf5e..95b1ba4ce470 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
>> @@ -189,8 +189,8 @@ vph_pwr: vph-pwr-regulator {
>> };
>>
>> &adsp {
>> - status = "okay";
>> firmware-name = "qcom/sm8350/Sony/sagami/adsp.mbn";
>> + status = "okay";
>> };
>>
>> &apps_rsc {
>> @@ -542,27 +542,27 @@ pmr735a_l7: ldo7 {
>> };
>>
>> &cdsp {
>> - status = "okay";
>> firmware-name = "qcom/sm8350/Sony/sagami/cdsp.mbn";
>> + status = "okay";
>> };
>>
>> &i2c1 {
>> - status = "okay";
>> clock-frequency = <1000000>;
>> + status = "okay";
>>
>> /* Some subset of SONY IMX663 camera sensor @ 38 */
>> };
>>
>> &i2c4 {
>> - status = "okay";
>> clock-frequency = <400000>;
>> + status = "okay";
>>
>> /* Samsung Touchscreen (needs I2C GPI DMA) @ 48 */
>> };
>>
>> &i2c11 {
>> - status = "okay";
>> clock-frequency = <1000000>;
>> + status = "okay";
>>
>> cs35l41_l: speaker-amp@40 {
>> compatible = "cirrus,cs35l41";
>> @@ -596,31 +596,31 @@ cs35l41_r: speaker-amp@41 {
>> };
>>
>> &i2c12 {
>> - status = "okay";
>> /* Clock frequency was not specified downstream, let's park it to 100 KHz */
>> clock-frequency = <100000>;
>> + status = "okay";
>>
>> /* AMS TCS3490 RGB+IR color sensor @ 72 */
>> };
>>
>> &i2c13 {
>> - status = "okay";
>> /* Clock frequency was not specified downstream, let's park it to 100 KHz */
>> clock-frequency = <100000>;
>> + status = "okay";
>>
>> /* Qualcomm PM8008i/PM8008j (?) @ 8, 9, c, d */
>> };
>>
>> &i2c15 {
>> - status = "okay";
>> clock-frequency = <400000>;
>> + status = "okay";
>>
>> /* NXP SN1X0 NFC @ 28 */
>> };
>>
>> &i2c17 {
>> - status = "okay";
>> clock-frequency = <1000000>;
>> + status = "okay";
>>
>> /* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
>> };
>> @@ -652,8 +652,8 @@ mdss_dp_altmode: endpoint {
>> };
>>
>> &mpss {
>> - status = "okay";
>> firmware-name = "qcom/sm8350/Sony/sagami/modem.mbn";
>> + status = "okay";
>> };
>>
>> &pm8350_gpios {
>> @@ -719,8 +719,8 @@ &pon_pwrkey {
>> };
>>
>> &pon_resin {
>> - status = "okay";
>> linux,code = <KEY_VOLUMEUP>;
>> + status = "okay";
>> };
>>
>> &qupv3_id_0 {
>> @@ -748,8 +748,8 @@ &sdhc_2 {
>> };
>>
>> &slpi {
>> - status = "okay";
>> firmware-name = "qcom/sm8350/Sony/sagami/slpi.mbn";
>> + status = "okay";
>> };
>>
>> &spi14 {
>> @@ -1038,16 +1038,14 @@ usb_1_dwc3_ss: endpoint {
>> };
>>
>> &usb_1_hsphy {
>> - status = "okay";
>> -
>> vdda-pll-supply = <&pm8350_l5>;
>> vdda18-supply = <&pm8350c_l1>;
>> vdda33-supply = <&pm8350_l2>;
>> + status = "okay";
>> };
>>
>> &usb_1_qmpphy {
>> - status = "okay";
>> -
>> vdda-phy-supply = <&pm8350_l6>;
>> vdda-pll-supply = <&pm8350_l1>;
>> + status = "okay";
>> };
>>
>> --
>> 2.40.0
>>
prev parent reply other threads:[~2023-04-03 10:17 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-21 22:12 [PATCH 0/4] Enable DisplayPort over USB-C on SONY Sagami Konrad Dybcio
2023-03-21 22:12 ` [PATCH 1/4] dt-bindings: usb: gpio-sbu-mux: Add OnSemi NB7VPQ904M mux Konrad Dybcio
2023-03-30 15:31 ` Rob Herring
2023-03-30 23:00 ` Konrad Dybcio
2023-03-21 22:12 ` [PATCH 2/4] arm64: dts: qcom: sm8350-sagami: Add PMIC GLINK Konrad Dybcio
2023-03-30 16:33 ` Neil Armstrong
2023-03-21 22:12 ` [PATCH 3/4] arm64: dts: qcom: sm8350-sagami: Hook up USB-C Display Port Konrad Dybcio
2023-03-21 22:12 ` [PATCH 4/4] arm64: dts: qcom: sm8350-nagara: Unify status property placement Konrad Dybcio
2023-03-30 16:32 ` Neil Armstrong
2023-04-02 15:19 ` Marijn Suijten
2023-04-03 10:17 ` Konrad Dybcio [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=97316d33-29b9-700f-8766-df538b133f35@linaro.org \
--to=konrad.dybcio@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=marijn.suijten@somainline.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).