[PATCH 0/4] Enable DisplayPort over USB-C on SONY Sagami

[PATCH 0/4] Enable DisplayPort over USB-C on SONY Sagami

[Konrad Dybcio]

DisplayPort is there before DSI panel, kinda funny!

Depends on:

https://lore.kernel.org/linux-arm-msm/20230130-topic-sm8450-upstream-pmic-glink-v5-0-552f3b721f9e@linaro.org
https://lore.kernel.org/linux-arm-msm/20230206-topic-sm8450-upstream-dp-controller-v6-3-d78313cbc41d@linaro.org

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
Konrad Dybcio (4):
      dt-bindings: usb: gpio-sbu-mux: Add OnSemi NB7VPQ904M mux
      arm64: dts: qcom: sm8350-sagami: Add PMIC GLINK
      arm64: dts: qcom: sm8350-sagami: Hook up USB-C Display Port
      arm64: dts: qcom: sm8350-nagara: Unify status property placement

 .../devicetree/bindings/usb/gpio-sbu-mux.yaml      |   1 +
 .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 162 ++++++++++++++++++---
 2 files changed, 146 insertions(+), 17 deletions(-)
---
base-commit: 52581937d6423c3bd15eb3894580ab87fe7308a1
change-id: 20230321-topic-sagami_dp-11f90e38d43c

Best regards,
-- 
Konrad Dybcio <konrad.dybcio@linaro.org>

[PATCH 1/4] dt-bindings: usb: gpio-sbu-mux: Add OnSemi NB7VPQ904M mux

[Konrad Dybcio]

The OnSemi NB7VPQ904M Type-C DP altmode redriver provides SBU signals
that can be used in with the gpio-sbu-mux driver. Document it.

Note that the -mux suffix is there to indicate that the gpio-sbu-mux
driver interacts with the mux part of this otherwise quite sophisticated
chip, leaving the "onnn,nb7vpq904m" compatible free for when a proper
driver taking care of all of the chip's capabilities is introduced.

Ref: https://www.onsemi.com/products/signal-conditioning-control/redrivers/nb7vpq904m

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml b/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml
index bf4b1d016e1f..a7206009b691 100644
--- a/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml
+++ b/Documentation/devicetree/bindings/usb/gpio-sbu-mux.yaml
@@ -20,6 +20,7 @@ properties:
     items:
       - enum:
           - onnn,fsusb43l10x
+          - onnn,nb7vpq904m-mux
           - pericom,pi3usb102
       - const: gpio-sbu-mux
 

-- 
2.40.0

Re: [PATCH 1/4] dt-bindings: usb: gpio-sbu-mux: Add OnSemi NB7VPQ904M mux

[Rob Herring]

On Tue, Mar 21, 2023 at 11:12:28PM +0100, Konrad Dybcio wrote:
> The OnSemi NB7VPQ904M Type-C DP altmode redriver provides SBU signals
> that can be used in with the gpio-sbu-mux driver. Document it.
> 
> Note that the -mux suffix is there to indicate that the gpio-sbu-mux
> driver interacts with the mux part of this otherwise quite sophisticated
> chip, leaving the "onnn,nb7vpq904m" compatible free for when a proper
> driver taking care of all of the chip's capabilities is introduced.

You should define a proper and complete binding. If you want to bind the 
gpio-sbu-mux driver to it now until you have a proper driver then that's 
fine. When you have such a driver, then you drop the compatible from the 
gpio-sbu-mux driver.

Note that having the fallback "gpio-sbu-mux" is somewhat problematic 
because the kernel has no mechanism to ensure you bind the most specific 
driver. For that to happen, it would have to support (automatically) 
unbinding one driver and binding to the more specific driver since one 
driver could be built-in and the other a module.

Rob

Re: [PATCH 1/4] dt-bindings: usb: gpio-sbu-mux: Add OnSemi NB7VPQ904M mux

[Konrad Dybcio]

On 30.03.2023 17:31, Rob Herring wrote:
> On Tue, Mar 21, 2023 at 11:12:28PM +0100, Konrad Dybcio wrote:
>> The OnSemi NB7VPQ904M Type-C DP altmode redriver provides SBU signals
>> that can be used in with the gpio-sbu-mux driver. Document it.
>>
>> Note that the -mux suffix is there to indicate that the gpio-sbu-mux
>> driver interacts with the mux part of this otherwise quite sophisticated
>> chip, leaving the "onnn,nb7vpq904m" compatible free for when a proper
>> driver taking care of all of the chip's capabilities is introduced.
> 
> You should define a proper and complete binding. If you want to bind the 
> gpio-sbu-mux driver to it now until you have a proper driver then that's 
> fine. When you have such a driver, then you drop the compatible from the 
> gpio-sbu-mux driver.
Okay, that makes perfect sense and is good to know. Perhaps even worth
documenting somewhere.

I think I'll delay resending this and get an "actual" driver going.

Konrad
> 
> Note that having the fallback "gpio-sbu-mux" is somewhat problematic 
> because the kernel has no mechanism to ensure you bind the most specific 
> driver. For that to happen, it would have to support (automatically) 
> unbinding one driver and binding to the more specific driver since one 
> driver could be built-in and the other a module.
> 
> Rob

[PATCH 2/4] arm64: dts: qcom: sm8350-sagami: Add PMIC GLINK

[Konrad Dybcio]

Sagami devices, like other 8350s, uses PMIC GLINK for various
functionality around battery, charging, TCPM etc. Enable it.

Worth noting:
My USB mouse is unimpressed when connected to the device via a
non-powered USB-C dock. Microsoft HD-500 dock refuses to estalish a
PD handshake.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 60 +++++++++++++++++++++-
 1 file changed, 59 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
index 89382ad73133..21462b6de686 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
@@ -89,6 +89,42 @@ key-vol-down {
 		};
 	};
 
+	pmic-glink {
+		compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_dwc3_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_dwc3_ss_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_ss>;
+					};
+				};
+			};
+		};
+	};
+
+
 	reserved-memory {
 		cont_splash_mem: memory@e1000000 {
 			reg = <0 0xe1000000 0 0x2300000>;
@@ -904,7 +940,29 @@ &usb_1 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			usb_1_dwc3_hs: endpoint {
+				remote-endpoint = <&pmic_glink_dwc3_hs_in>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			usb_1_dwc3_ss: endpoint {
+				remote-endpoint = <&pmic_glink_dwc3_ss_in>;
+			};
+		};
+	};
 };
 
 &usb_1_hsphy {

-- 
2.40.0

Re: [PATCH 2/4] arm64: dts: qcom: sm8350-sagami: Add PMIC GLINK

[Neil Armstrong]

Le 21/03/2023 à 23:12, Konrad Dybcio a écrit :
> Sagami devices, like other 8350s, uses PMIC GLINK for various
> functionality around battery, charging, TCPM etc. Enable it.
> 
> Worth noting:
> My USB mouse is unimpressed when connected to the device via a
> non-powered USB-C dock. Microsoft HD-500 dock refuses to estalish a
> PD handshake.

That's interesting... perhaps UCSI is required here ?

> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>   .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 60 +++++++++++++++++++++-
>   1 file changed, 59 insertions(+), 1 deletion(-)
> 

<snip>
Anyway:
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>

[PATCH 3/4] arm64: dts: qcom: sm8350-sagami: Hook up USB-C Display Port

[Konrad Dybcio]

Sagami devices feature Display Port on their USB-C port. Add the
necessary nodes to support it.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 72 ++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
index 21462b6de686..b2baa81baf5e 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
@@ -120,6 +120,23 @@ pmic_glink_dwc3_ss_in: endpoint {
 						remote-endpoint = <&usb_1_dwc3_ss>;
 					};
 				};
+
+				port@2 {
+					reg = <2>;
+
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pmic_glink_dp_in: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&mdss_dp_altmode>;
+					};
+
+					pmic_glink_sbu_mux_out: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&sbu_mux_in>;
+					};
+				};
 			};
 		};
 	};
@@ -140,6 +157,26 @@ ramoops@ffc00000 {
 		};
 	};
 
+	sbu-mux {
+		/* TODO: switch to a proper driver when one gets upstreamed */
+		compatible = "onnn,nb7vpq904m-mux", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+		select-gpios = <&tlmm 55 GPIO_ACTIVE_HIGH>;
+		svid = /bits/ 16 <0xff01>;
+
+		mode-switch;
+		orientation-switch;
+
+		pinctrl-0 = <&sbu_sw_oe &sbu_sw_sel>;
+
+		port {
+			sbu_mux_in: endpoint {
+				remote-endpoint = <&pmic_glink_sbu_mux_out>;
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -595,6 +632,25 @@ &ipa {
 	status = "okay";
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp {
+	data-lanes = <0 1 2 3>;
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mdss_dp_altmode: endpoint {
+				remote-endpoint = <&pmic_glink_dp_in>;
+			};
+		};
+	};
+};
+
 &mpss {
 	status = "okay";
 	firmware-name = "qcom/sm8350/Sony/sagami/modem.mbn";
@@ -916,6 +972,22 @@ ts_int_default: ts-int-default-state {
 		input-enable;
 	};
 
+	sbu_sw_oe: sbu-sw-oe-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	sbu_sw_sel: sbu-sw-sel-state {
+		pins = "gpio55";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
 	sdc2_card_det_active: sd-card-det-active-state {
 		pins = "gpio92";
 		function = "gpio";

-- 
2.40.0

[PATCH 4/4] arm64: dts: qcom: sm8350-nagara: Unify status property placement

[Konrad Dybcio]

As we're heading towards getting the status property last everywhere,
take care of it for SM8350 SONY Sagami.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 30 ++++++++++------------
 1 file changed, 14 insertions(+), 16 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
index b2baa81baf5e..95b1ba4ce470 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
@@ -189,8 +189,8 @@ vph_pwr: vph-pwr-regulator {
 };
 
 &adsp {
-	status = "okay";
 	firmware-name = "qcom/sm8350/Sony/sagami/adsp.mbn";
+	status = "okay";
 };
 
 &apps_rsc {
@@ -542,27 +542,27 @@ pmr735a_l7: ldo7 {
 };
 
 &cdsp {
-	status = "okay";
 	firmware-name = "qcom/sm8350/Sony/sagami/cdsp.mbn";
+	status = "okay";
 };
 
 &i2c1 {
-	status = "okay";
 	clock-frequency = <1000000>;
+	status = "okay";
 
 	/* Some subset of SONY IMX663 camera sensor @ 38 */
 };
 
 &i2c4 {
-	status = "okay";
 	clock-frequency = <400000>;
+	status = "okay";
 
 	/* Samsung Touchscreen (needs I2C GPI DMA) @ 48 */
 };
 
 &i2c11 {
-	status = "okay";
 	clock-frequency = <1000000>;
+	status = "okay";
 
 	cs35l41_l: speaker-amp@40 {
 		compatible = "cirrus,cs35l41";
@@ -596,31 +596,31 @@ cs35l41_r: speaker-amp@41 {
 };
 
 &i2c12 {
-	status = "okay";
 	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
 	clock-frequency = <100000>;
+	status = "okay";
 
 	/* AMS TCS3490 RGB+IR color sensor @ 72 */
 };
 
 &i2c13 {
-	status = "okay";
 	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
 	clock-frequency = <100000>;
+	status = "okay";
 
 	/* Qualcomm PM8008i/PM8008j (?) @ 8, 9, c, d */
 };
 
 &i2c15 {
-	status = "okay";
 	clock-frequency = <400000>;
+	status = "okay";
 
 	/* NXP SN1X0 NFC @ 28 */
 };
 
 &i2c17 {
-	status = "okay";
 	clock-frequency = <1000000>;
+	status = "okay";
 
 	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
 };
@@ -652,8 +652,8 @@ mdss_dp_altmode: endpoint {
 };
 
 &mpss {
-	status = "okay";
 	firmware-name = "qcom/sm8350/Sony/sagami/modem.mbn";
+	status = "okay";
 };
 
 &pm8350_gpios {
@@ -719,8 +719,8 @@ &pon_pwrkey {
 };
 
 &pon_resin {
-	status = "okay";
 	linux,code = <KEY_VOLUMEUP>;
+	status = "okay";
 };
 
 &qupv3_id_0 {
@@ -748,8 +748,8 @@ &sdhc_2 {
 };
 
 &slpi {
-	status = "okay";
 	firmware-name = "qcom/sm8350/Sony/sagami/slpi.mbn";
+	status = "okay";
 };
 
 &spi14 {
@@ -1038,16 +1038,14 @@ usb_1_dwc3_ss: endpoint {
 };
 
 &usb_1_hsphy {
-	status = "okay";
-
 	vdda-pll-supply = <&pm8350_l5>;
 	vdda18-supply = <&pm8350c_l1>;
 	vdda33-supply = <&pm8350_l2>;
+	status = "okay";
 };
 
 &usb_1_qmpphy {
-	status = "okay";
-
 	vdda-phy-supply = <&pm8350_l6>;
 	vdda-pll-supply = <&pm8350_l1>;
+	status = "okay";
 };

-- 
2.40.0

Re: [PATCH 4/4] arm64: dts: qcom: sm8350-nagara: Unify status property placement

[Neil Armstrong]

Le 21/03/2023 à 23:12, Konrad Dybcio a écrit :
> As we're heading towards getting the status property last everywhere,
> take care of it for SM8350 SONY Sagami.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>   .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 30 ++++++++++------------
>   1 file changed, 14 insertions(+), 16 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
> index b2baa81baf5e..95b1ba4ce470 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
> @@ -189,8 +189,8 @@ vph_pwr: vph-pwr-regulator {
>   };
>   
>   &adsp {
> -	status = "okay";
>   	firmware-name = "qcom/sm8350/Sony/sagami/adsp.mbn";
> +	status = "okay";
>   };
>   
>   &apps_rsc {
> @@ -542,27 +542,27 @@ pmr735a_l7: ldo7 {
>   };
>   
>   &cdsp {
> -	status = "okay";
>   	firmware-name = "qcom/sm8350/Sony/sagami/cdsp.mbn";
> +	status = "okay";
>   };
>   
>   &i2c1 {
> -	status = "okay";
>   	clock-frequency = <1000000>;
> +	status = "okay";
>   
>   	/* Some subset of SONY IMX663 camera sensor @ 38 */
>   };
>   
>   &i2c4 {
> -	status = "okay";
>   	clock-frequency = <400000>;
> +	status = "okay";
>   
>   	/* Samsung Touchscreen (needs I2C GPI DMA) @ 48 */
>   };
>   
>   &i2c11 {
> -	status = "okay";
>   	clock-frequency = <1000000>;
> +	status = "okay";
>   
>   	cs35l41_l: speaker-amp@40 {
>   		compatible = "cirrus,cs35l41";
> @@ -596,31 +596,31 @@ cs35l41_r: speaker-amp@41 {
>   };
>   
>   &i2c12 {
> -	status = "okay";
>   	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
>   	clock-frequency = <100000>;
> +	status = "okay";
>   
>   	/* AMS TCS3490 RGB+IR color sensor @ 72 */
>   };
>   
>   &i2c13 {
> -	status = "okay";
>   	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
>   	clock-frequency = <100000>;
> +	status = "okay";
>   
>   	/* Qualcomm PM8008i/PM8008j (?) @ 8, 9, c, d */
>   };
>   
>   &i2c15 {
> -	status = "okay";
>   	clock-frequency = <400000>;
> +	status = "okay";
>   
>   	/* NXP SN1X0 NFC @ 28 */
>   };
>   
>   &i2c17 {
> -	status = "okay";
>   	clock-frequency = <1000000>;
> +	status = "okay";
>   
>   	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
>   };
> @@ -652,8 +652,8 @@ mdss_dp_altmode: endpoint {
>   };
>   
>   &mpss {
> -	status = "okay";
>   	firmware-name = "qcom/sm8350/Sony/sagami/modem.mbn";
> +	status = "okay";
>   };
>   
>   &pm8350_gpios {
> @@ -719,8 +719,8 @@ &pon_pwrkey {
>   };
>   
>   &pon_resin {
> -	status = "okay";
>   	linux,code = <KEY_VOLUMEUP>;
> +	status = "okay";
>   };
>   
>   &qupv3_id_0 {
> @@ -748,8 +748,8 @@ &sdhc_2 {
>   };
>   
>   &slpi {
> -	status = "okay";
>   	firmware-name = "qcom/sm8350/Sony/sagami/slpi.mbn";
> +	status = "okay";
>   };
>   
>   &spi14 {
> @@ -1038,16 +1038,14 @@ usb_1_dwc3_ss: endpoint {
>   };
>   
>   &usb_1_hsphy {
> -	status = "okay";
> -
>   	vdda-pll-supply = <&pm8350_l5>;
>   	vdda18-supply = <&pm8350c_l1>;
>   	vdda33-supply = <&pm8350_l2>;
> +	status = "okay";
>   };
>   
>   &usb_1_qmpphy {
> -	status = "okay";
> -
>   	vdda-phy-supply = <&pm8350_l6>;
>   	vdda-pll-supply = <&pm8350_l1>;
> +	status = "okay";
>   };
> 

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>

Re: [PATCH 4/4] arm64: dts: qcom: sm8350-nagara: Unify status property placement

[Marijn Suijten]

On 2023-03-21 23:12:31, Konrad Dybcio wrote:

When you get to resending this, change sm8350-nagara in the title to
sm8350-sagami :)

- Marijn

> As we're heading towards getting the status property last everywhere,
> take care of it for SM8350 SONY Sagami.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 30 ++++++++++------------
>  1 file changed, 14 insertions(+), 16 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
> index b2baa81baf5e..95b1ba4ce470 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
> @@ -189,8 +189,8 @@ vph_pwr: vph-pwr-regulator {
>  };
>  
>  &adsp {
> -	status = "okay";
>  	firmware-name = "qcom/sm8350/Sony/sagami/adsp.mbn";
> +	status = "okay";
>  };
>  
>  &apps_rsc {
> @@ -542,27 +542,27 @@ pmr735a_l7: ldo7 {
>  };
>  
>  &cdsp {
> -	status = "okay";
>  	firmware-name = "qcom/sm8350/Sony/sagami/cdsp.mbn";
> +	status = "okay";
>  };
>  
>  &i2c1 {
> -	status = "okay";
>  	clock-frequency = <1000000>;
> +	status = "okay";
>  
>  	/* Some subset of SONY IMX663 camera sensor @ 38 */
>  };
>  
>  &i2c4 {
> -	status = "okay";
>  	clock-frequency = <400000>;
> +	status = "okay";
>  
>  	/* Samsung Touchscreen (needs I2C GPI DMA) @ 48 */
>  };
>  
>  &i2c11 {
> -	status = "okay";
>  	clock-frequency = <1000000>;
> +	status = "okay";
>  
>  	cs35l41_l: speaker-amp@40 {
>  		compatible = "cirrus,cs35l41";
> @@ -596,31 +596,31 @@ cs35l41_r: speaker-amp@41 {
>  };
>  
>  &i2c12 {
> -	status = "okay";
>  	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
>  	clock-frequency = <100000>;
> +	status = "okay";
>  
>  	/* AMS TCS3490 RGB+IR color sensor @ 72 */
>  };
>  
>  &i2c13 {
> -	status = "okay";
>  	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
>  	clock-frequency = <100000>;
> +	status = "okay";
>  
>  	/* Qualcomm PM8008i/PM8008j (?) @ 8, 9, c, d */
>  };
>  
>  &i2c15 {
> -	status = "okay";
>  	clock-frequency = <400000>;
> +	status = "okay";
>  
>  	/* NXP SN1X0 NFC @ 28 */
>  };
>  
>  &i2c17 {
> -	status = "okay";
>  	clock-frequency = <1000000>;
> +	status = "okay";
>  
>  	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
>  };
> @@ -652,8 +652,8 @@ mdss_dp_altmode: endpoint {
>  };
>  
>  &mpss {
> -	status = "okay";
>  	firmware-name = "qcom/sm8350/Sony/sagami/modem.mbn";
> +	status = "okay";
>  };
>  
>  &pm8350_gpios {
> @@ -719,8 +719,8 @@ &pon_pwrkey {
>  };
>  
>  &pon_resin {
> -	status = "okay";
>  	linux,code = <KEY_VOLUMEUP>;
> +	status = "okay";
>  };
>  
>  &qupv3_id_0 {
> @@ -748,8 +748,8 @@ &sdhc_2 {
>  };
>  
>  &slpi {
> -	status = "okay";
>  	firmware-name = "qcom/sm8350/Sony/sagami/slpi.mbn";
> +	status = "okay";
>  };
>  
>  &spi14 {
> @@ -1038,16 +1038,14 @@ usb_1_dwc3_ss: endpoint {
>  };
>  
>  &usb_1_hsphy {
> -	status = "okay";
> -
>  	vdda-pll-supply = <&pm8350_l5>;
>  	vdda18-supply = <&pm8350c_l1>;
>  	vdda33-supply = <&pm8350_l2>;
> +	status = "okay";
>  };
>  
>  &usb_1_qmpphy {
> -	status = "okay";
> -
>  	vdda-phy-supply = <&pm8350_l6>;
>  	vdda-pll-supply = <&pm8350_l1>;
> +	status = "okay";
>  };
> 
> -- 
> 2.40.0
> 

Re: [PATCH 4/4] arm64: dts: qcom: sm8350-nagara: Unify status property placement

[Konrad Dybcio]

On 2.04.2023 17:19, Marijn Suijten wrote:
> On 2023-03-21 23:12:31, Konrad Dybcio wrote:
> 
> When you get to resending this, change sm8350-nagara in the title to
> sm8350-sagami :)
Even I confuse them, they just look too alike! ;)

Konrad
> 
> - Marijn
> 
>> As we're heading towards getting the status property last everywhere,
>> take care of it for SM8350 SONY Sagami.
>>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>>  .../boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 30 ++++++++++------------
>>  1 file changed, 14 insertions(+), 16 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
>> index b2baa81baf5e..95b1ba4ce470 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
>> @@ -189,8 +189,8 @@ vph_pwr: vph-pwr-regulator {
>>  };
>>  
>>  &adsp {
>> -	status = "okay";
>>  	firmware-name = "qcom/sm8350/Sony/sagami/adsp.mbn";
>> +	status = "okay";
>>  };
>>  
>>  &apps_rsc {
>> @@ -542,27 +542,27 @@ pmr735a_l7: ldo7 {
>>  };
>>  
>>  &cdsp {
>> -	status = "okay";
>>  	firmware-name = "qcom/sm8350/Sony/sagami/cdsp.mbn";
>> +	status = "okay";
>>  };
>>  
>>  &i2c1 {
>> -	status = "okay";
>>  	clock-frequency = <1000000>;
>> +	status = "okay";
>>  
>>  	/* Some subset of SONY IMX663 camera sensor @ 38 */
>>  };
>>  
>>  &i2c4 {
>> -	status = "okay";
>>  	clock-frequency = <400000>;
>> +	status = "okay";
>>  
>>  	/* Samsung Touchscreen (needs I2C GPI DMA) @ 48 */
>>  };
>>  
>>  &i2c11 {
>> -	status = "okay";
>>  	clock-frequency = <1000000>;
>> +	status = "okay";
>>  
>>  	cs35l41_l: speaker-amp@40 {
>>  		compatible = "cirrus,cs35l41";
>> @@ -596,31 +596,31 @@ cs35l41_r: speaker-amp@41 {
>>  };
>>  
>>  &i2c12 {
>> -	status = "okay";
>>  	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
>>  	clock-frequency = <100000>;
>> +	status = "okay";
>>  
>>  	/* AMS TCS3490 RGB+IR color sensor @ 72 */
>>  };
>>  
>>  &i2c13 {
>> -	status = "okay";
>>  	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
>>  	clock-frequency = <100000>;
>> +	status = "okay";
>>  
>>  	/* Qualcomm PM8008i/PM8008j (?) @ 8, 9, c, d */
>>  };
>>  
>>  &i2c15 {
>> -	status = "okay";
>>  	clock-frequency = <400000>;
>> +	status = "okay";
>>  
>>  	/* NXP SN1X0 NFC @ 28 */
>>  };
>>  
>>  &i2c17 {
>> -	status = "okay";
>>  	clock-frequency = <1000000>;
>> +	status = "okay";
>>  
>>  	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
>>  };
>> @@ -652,8 +652,8 @@ mdss_dp_altmode: endpoint {
>>  };
>>  
>>  &mpss {
>> -	status = "okay";
>>  	firmware-name = "qcom/sm8350/Sony/sagami/modem.mbn";
>> +	status = "okay";
>>  };
>>  
>>  &pm8350_gpios {
>> @@ -719,8 +719,8 @@ &pon_pwrkey {
>>  };
>>  
>>  &pon_resin {
>> -	status = "okay";
>>  	linux,code = <KEY_VOLUMEUP>;
>> +	status = "okay";
>>  };
>>  
>>  &qupv3_id_0 {
>> @@ -748,8 +748,8 @@ &sdhc_2 {
>>  };
>>  
>>  &slpi {
>> -	status = "okay";
>>  	firmware-name = "qcom/sm8350/Sony/sagami/slpi.mbn";
>> +	status = "okay";
>>  };
>>  
>>  &spi14 {
>> @@ -1038,16 +1038,14 @@ usb_1_dwc3_ss: endpoint {
>>  };
>>  
>>  &usb_1_hsphy {
>> -	status = "okay";
>> -
>>  	vdda-pll-supply = <&pm8350_l5>;
>>  	vdda18-supply = <&pm8350c_l1>;
>>  	vdda33-supply = <&pm8350_l2>;
>> +	status = "okay";
>>  };
>>  
>>  &usb_1_qmpphy {
>> -	status = "okay";
>> -
>>  	vdda-phy-supply = <&pm8350_l6>;
>>  	vdda-pll-supply = <&pm8350_l1>;
>> +	status = "okay";
>>  };
>>
>> -- 
>> 2.40.0
>>