From: Wasim Nazir <quic_wasimn@quicinc.com>
To: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
<linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <kernel@quicinc.com>
Subject: Re: [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8
Date: Tue, 19 Nov 2024 22:57:20 +0530 [thread overview]
Message-ID: <ZzzKePPcjDAhiaM3@hu-wasimn-hyd.qualcomm.com> (raw)
In-Reply-To: <5r4m3p3kwix2jjp23l5eqk74mbt2dusozwxml4um2i773qxb6g@swzszlybrqfa>
On Sat, Nov 16, 2024 at 01:53:00AM +0200, Dmitry Baryshkov wrote:
> On Sat, Nov 16, 2024 at 04:21:51AM +0530, Wasim Nazir wrote:
> > Add device tree support for the QCS9075-RB8 board.
> >
> > Basic changes are supported for boot to shell.
> >
> > Signed-off-by: Wasim Nazir <quic_wasimn@quicinc.com>
> > ---
> > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > arch/arm64/boot/dts/qcom/qcs9075-rb8.dts | 281 +++++++++++++++++++++++
> > 2 files changed, 282 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> >
> > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> > index 9bb8b191aeb5..5d9847119f2e 100644
> > --- a/arch/arm64/boot/dts/qcom/Makefile
> > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > @@ -115,6 +115,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
> > +dtb-$(CONFIG_ARCH_QCOM) += qcs9075-rb8.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
> > diff --git a/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> > new file mode 100644
> > index 000000000000..e4307ff1e2a7
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/qcs9075-rb8.dts
> > @@ -0,0 +1,281 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +/*
> > + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
> > + */
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> > +
> > +#include "sa8775p.dtsi"
> > +#include "sa8775p-pmics.dtsi"
> > +
> > +/ {
> > + model = "Qualcomm Technologies, Inc. QCS9075 RB8";
>
> Is this going to be an actual product name? Usually RBx boards are named
> differently.
Will update it in next series.
>
> > + compatible = "qcom,qcs9075-rb8", "qcom,qcs9075", "qcom,sa8775p";
> > +
> > + aliases {
> > + serial0 = &uart10;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +};
> > +
> > +&apps_rsc {
> > + regulators-0 {
> > + compatible = "qcom,pmm8654au-rpmh-regulators";
> > + qcom,pmic-id = "a";
> > +
> > + vreg_s4a: smps4 {
> > + regulator-name = "vreg_s4a";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1816000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s5a: smps5 {
> > + regulator-name = "vreg_s5a";
> > + regulator-min-microvolt = <1850000>;
> > + regulator-max-microvolt = <1996000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s9a: smps9 {
> > + regulator-name = "vreg_s9a";
> > + regulator-min-microvolt = <535000>;
> > + regulator-max-microvolt = <1120000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l4a: ldo4 {
> > + regulator-name = "vreg_l4a";
> > + regulator-min-microvolt = <788000>;
> > + regulator-max-microvolt = <1050000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l5a: ldo5 {
> > + regulator-name = "vreg_l5a";
> > + regulator-min-microvolt = <870000>;
> > + regulator-max-microvolt = <950000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l6a: ldo6 {
> > + regulator-name = "vreg_l6a";
> > + regulator-min-microvolt = <870000>;
> > + regulator-max-microvolt = <970000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l7a: ldo7 {
> > + regulator-name = "vreg_l7a";
> > + regulator-min-microvolt = <720000>;
> > + regulator-max-microvolt = <950000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l8a: ldo8 {
> > + regulator-name = "vreg_l8a";
> > + regulator-min-microvolt = <2504000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l9a: ldo9 {
> > + regulator-name = "vreg_l9a";
> > + regulator-min-microvolt = <2970000>;
> > + regulator-max-microvolt = <3544000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > + };
> > +
> > + regulators-1 {
> > + compatible = "qcom,pmm8654au-rpmh-regulators";
> > + qcom,pmic-id = "c";
> > +
> > + vreg_l1c: ldo1 {
> > + regulator-name = "vreg_l1c";
> > + regulator-min-microvolt = <1140000>;
> > + regulator-max-microvolt = <1260000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l2c: ldo2 {
> > + regulator-name = "vreg_l2c";
> > + regulator-min-microvolt = <900000>;
> > + regulator-max-microvolt = <1100000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l3c: ldo3 {
> > + regulator-name = "vreg_l3c";
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l4c: ldo4 {
> > + regulator-name = "vreg_l4c";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + /*
> > + * FIXME: This should have regulator-allow-set-load but
> > + * we're getting an over-current fault from the PMIC
> > + * when switching to LPM.
> > + */
> > + };
> > +
> > + vreg_l5c: ldo5 {
> > + regulator-name = "vreg_l5c";
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l6c: ldo6 {
> > + regulator-name = "vreg_l6c";
> > + regulator-min-microvolt = <1620000>;
> > + regulator-max-microvolt = <1980000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l7c: ldo7 {
> > + regulator-name = "vreg_l7c";
> > + regulator-min-microvolt = <1620000>;
> > + regulator-max-microvolt = <2000000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l8c: ldo8 {
> > + regulator-name = "vreg_l8c";
> > + regulator-min-microvolt = <2400000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l9c: ldo9 {
> > + regulator-name = "vreg_l9c";
> > + regulator-min-microvolt = <1650000>;
> > + regulator-max-microvolt = <2700000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > + };
> > +
> > + regulators-2 {
> > + compatible = "qcom,pmm8654au-rpmh-regulators";
> > + qcom,pmic-id = "e";
> > +
> > + vreg_s4e: smps4 {
> > + regulator-name = "vreg_s4e";
> > + regulator-min-microvolt = <970000>;
> > + regulator-max-microvolt = <1520000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s7e: smps7 {
> > + regulator-name = "vreg_s7e";
> > + regulator-min-microvolt = <1010000>;
> > + regulator-max-microvolt = <1170000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_s9e: smps9 {
> > + regulator-name = "vreg_s9e";
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <570000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l6e: ldo6 {
> > + regulator-name = "vreg_l6e";
> > + regulator-min-microvolt = <1280000>;
> > + regulator-max-microvolt = <1450000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > +
> > + vreg_l8e: ldo8 {
> > + regulator-name = "vreg_l8e";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1950000>;
> > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > + regulator-allow-set-load;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> > + RPMH_REGULATOR_MODE_HPM>;
> > + };
> > + };
> > +};
> > +
> > +&qupv3_id_1 {
> > + status = "okay";
> > +};
> > +
> > +&sleep_clk {
> > + clock-frequency = <32768>;
> > +};
> > +
> > +&tlmm {
> > + qup_uart10_default: qup-uart10-state {
> > + pins = "gpio46", "gpio47";
> > + function = "qup1_se3";
> > + };
> > +};
> > +
> > +&uart10 {
> > + compatible = "qcom,geni-debug-uart";
> > + pinctrl-0 = <&qup_uart10_default>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +&xo_board_clk {
> > + clock-frequency = <38400000>;
> > +};
> > --
> > 2.47.0
> >
>
> --
> With best wishes
> Dmitry
Thanks & Regards,
Wasim
next prev parent reply other threads:[~2024-11-19 17:27 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-11-15 22:51 [PATCH v2 0/5] arm64: qcom: Add support for QCS9075 boards Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 1/5] dt-bindings: arm: qcom,ids: add SoC ID for QCS9075 Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 2/5] soc: qcom: socinfo: add QCS9075 SoC ID Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 3/5] dt-bindings: arm: qcom: Document rb8/ride/ride-r3 on QCS9075 Wasim Nazir
2024-11-15 22:51 ` [PATCH v2 4/5] arm64: dts: qcom: Add support for QCS9075 RB8 Wasim Nazir
2024-11-15 23:53 ` Dmitry Baryshkov
2024-11-19 17:27 ` Wasim Nazir [this message]
2024-11-15 22:51 ` [PATCH v2 5/5] arm64: dts: qcom: Add support for QCS9075 Ride & Ride-r3 Wasim Nazir
2024-11-15 23:54 ` Dmitry Baryshkov
2024-11-19 17:38 ` Wasim Nazir
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ZzzKePPcjDAhiaM3@hu-wasimn-hyd.qualcomm.com \
--to=quic_wasimn@quicinc.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=kernel@quicinc.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox