Re: [PATCH v2 4/6] ARM: dts: qcom: apq8074-dragonboard: add resin and gpio keys

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 8.05.2023 18:04, Dmitry Baryshkov wrote:
> Add device nodes for resin (reset, volume-down) and gpio-keys
> (volume-up, general key) device nodes.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  .../arm/boot/dts/qcom-apq8074-dragonboard.dts | 39 +++++++++++++++++++
>  1 file changed, 39 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
> index 1345df7cbd00..630180edecfd 100644
> --- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
> +++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
> @@ -1,5 +1,7 @@
>  // SPDX-License-Identifier: GPL-2.0
>  #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
>  #include "qcom-msm8974.dtsi"
>  #include "qcom-pm8841.dtsi"
>  #include "qcom-pm8941.dtsi"
> @@ -17,6 +19,26 @@ aliases {
>  	chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		autorepeat;
> +
> +		pinctrl-0 = <&msm_keys_default>;
> +		pinctrl-names = "default";
> +
> +		button-volup {
> +			label = "Volume Up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		button-general {
> +			label = "General";
> +			linux,code = <KEY_PROG1>;
> +			gpios = <&pm8941_gpios 23 GPIO_ACTIVE_LOW>;
> +		};
> +	};
>  };
>  
>  &blsp1_uart2 {
> @@ -35,6 +57,23 @@ eeprom: eeprom@52 {
>  	};
>  };
>  
> +&pm8941_gpios {
> +        msm_keys_default: pm8941-gpio-keys-state {
> +		pins = "gpio5", "gpio23";
> +		function = "normal";
> +		input-enable;
> +		drive-push-pull;
> +		bias-pull-up;
> +		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
> +		power-source = <PM8941_GPIO_S3>; /* 1.8V */
> +        };
> +};
> +
> +&pm8941_resin {
> +	linux,code = <KEY_VOLUMEDOWN>;
> +	status = "okay";
> +};
> +
>  &rpm_requests {
>  	regulators-0 {
>  		compatible = "qcom,rpm-pm8841-regulators";