From: Andrew Peng <pengms1@lenovo.com>
To: linux-aspeed@lists.ozlabs.org
Subject: [PATCH v6] ARM: dts: aspeed: Adding Lenovo Hr630 BMC
Date: Sun, 05 May 2019 06:08:56 -0000 [thread overview]
Message-ID: <1557036518-286348-1-git-send-email-pengms1@lenovo.com> (raw)
Initial introduction of Lenovo Hr630 family equipped with
Aspeed 2500 BMC SoC. Hr630 is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Lenovo.
Specifically, This adds the Hr630 platform device tree file
used by the Hr630 BMC machines.
This also adds an entry of Hr630 device tree file in Makefile
Signed-off-by: Andrew Peng <pengms1@lenovo.com>
Signed-off-by: Yonghui Liu <liuyh21@lenovo.com>
Signed-off-by: Lisa Liu <liuyj19@lenovo.com>
---
Changes in v6:
- add appropriate pinctrl property for uar1, uart2, uart3 and adc.
- remove vhub definition and comment.
- remove some GPIO definitions.
- revise Makefile according to sort alphabetically.
Changes in v5:
- revise pca9545 and pca9546 switch aliases name.
Changes in v4:
- add pca9546 switch aliases name.
Changes in v3:
- revise i2c switch aliases name.
Changes in v2:
- add i2c switch aliases name.
- remove the unused eeprom device from DT file.
- remove "Licensed under..." sentence.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts | 566 ++++++++++++++++++++++++++
2 files changed, 567 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f4f5aea..1276167 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1255,6 +1255,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-tiogapass.dtb \
aspeed-bmc-intel-s2600wf.dtb \
+ aspeed-bmc-lenovo-hr630.dtb \
aspeed-bmc-opp-lanyang.dtb \
aspeed-bmc-opp-palmetto.dtb \
aspeed-bmc-opp-romulus.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
new file mode 100644
index 0000000..d3695a3
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
@@ -0,0 +1,566 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for Lenovo Hr630 platform
+ *
+ * Copyright (C) 2019-present Lenovo
+ */
+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "HR630 BMC";
+ compatible = "lenovo,hr630-bmc", "aspeed,ast2500";
+
+ aliases {
+ i2c14 = &i2c_rbp;
+ i2c15 = &i2c_fbp1;
+ i2c16 = &i2c_fbp2;
+ i2c17 = &i2c_fbp3;
+ i2c18 = &i2c_riser2;
+ i2c19 = &i2c_pcie4;
+ i2c20 = &i2c_riser1;
+ i2c21 = &i2c_ocp;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
+ };
+
+ memory at 80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ flash_memory: region at 98000000 {
+ no-map;
+ reg = <0x98000000 0x00100000>; /* 1M */
+ };
+
+ gfx_memory: framebuffer {
+ size = <0x01000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ heartbeat {
+ gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_LOW>;
+ };
+
+ fault {
+ gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+ <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+ <&adc 8>, <&adc 9>, <&adc 10>,
+ <&adc 12>, <&adc 13>, <&adc 14>;
+ };
+
+};
+
+&fmc {
+ status = "okay";
+ flash at 0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout.dtsi"
+ };
+};
+
+&lpc_ctrl {
+ status = "okay";
+ memory-region = <&flash_memory>;
+ flash = <&spi1>;
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd1_default
+ &pinctrl_rxd1_default>;
+};
+
+&uart2 {
+ /* Rear RS-232 connector */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd2_default
+ &pinctrl_rxd2_default
+ &pinctrl_nrts2_default
+ &pinctrl_ndtr2_default
+ &pinctrl_ndsr2_default
+ &pinctrl_ncts2_default
+ &pinctrl_ndcd2_default
+ &pinctrl_nri2_default>;
+};
+
+&uart3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd3_default
+ &pinctrl_rxd3_default>;
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&ibt {
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii1_default>;
+ use-ncsi;
+};
+
+&mac1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&adc {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default
+ &pinctrl_adc1_default
+ &pinctrl_adc2_default
+ &pinctrl_adc3_default
+ &pinctrl_adc4_default
+ &pinctrl_adc5_default
+ &pinctrl_adc6_default
+ &pinctrl_adc7_default
+ &pinctrl_adc8_default
+ &pinctrl_adc9_default
+ &pinctrl_adc10_default
+ &pinctrl_adc12_default
+ &pinctrl_adc13_default
+ &pinctrl_adc14_default>;
+};
+
+&i2c0 {
+ status = "okay";
+ /* temp1 inlet */
+ tmp75 at 4e {
+ compatible = "national,lm75";
+ reg = <0x4e>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ /* temp2 outlet */
+ tmp75 at 4d {
+ compatible = "national,lm75";
+ reg = <0x4d>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+ /* Slot 0,
+ * Slot 1,
+ * Slot 2,
+ * Slot 3
+ */
+
+ i2c-switch at 70 {
+ compatible = "nxp,pca9545";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect; /* may use mux at 70 next. */
+
+ i2c_rbp: i2c at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c_fbp1: i2c at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c_fbp2: i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c_fbp3: i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ /* Slot 0,
+ * Slot 1,
+ * Slot 2,
+ * Slot 3
+ */
+ i2c-switch at 76 {
+ compatible = "nxp,pca9546";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect; /* may use mux at 76 next. */
+
+ i2c_riser2: i2c at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c_pcie4: i2c at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c_riser1: i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c_ocp: i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c8 {
+ status = "okay";
+
+ eeprom at 57 {
+ compatible = "atmel,24c256";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+};
+
+&i2c12 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&uhci {
+ status = "okay";
+};
+
+&gfx {
+ status = "okay";
+ memory-region = <&gfx_memory>;
+};
+
+&pwm_tacho {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_default
+ &pinctrl_pwm1_default
+ &pinctrl_pwm2_default
+ &pinctrl_pwm3_default
+ &pinctrl_pwm4_default
+ &pinctrl_pwm5_default
+ &pinctrl_pwm6_default>;
+
+ fan at 0 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+ };
+
+ fan at 1 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+ };
+
+ fan at 2 {
+ reg = <0x01>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+ };
+
+ fan at 3 {
+ reg = <0x01>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+ };
+
+ fan at 4 {
+ reg = <0x02>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+ };
+
+ fan at 5 {
+ reg = <0x02>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+ };
+
+ fan at 6 {
+ reg = <0x03>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+ };
+
+ fan at 7 {
+ reg = <0x03>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+ };
+
+ fan at 8 {
+ reg = <0x04>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+ };
+
+ fan at 9 {
+ reg = <0x04>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+ };
+
+ fan at 10 {
+ reg = <0x05>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+ };
+
+ fan at 11 {
+ reg = <0x05>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+ };
+
+ fan at 12 {
+ reg = <0x06>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+ };
+
+ fan at 13 {
+ reg = <0x06>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+ };
+};
+
+&gpio {
+
+ pin_gpio_b5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "IRQ_BMC_PCH_SMI_LPC_N";
+ };
+
+ pin_gpio_f0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "IRQ_BMC_PCH_NMI_R";
+ };
+
+ pin_gpio_f3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_BUS0_RST_OUT_N";
+ };
+
+ pin_gpio_f4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "FM_SKT0_FAULT_LED";
+ };
+
+ pin_gpio_f5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "FM_SKT1_FAULT_LED";
+ };
+
+ pin_gpio_g4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "FAN_PWR_CTL_N";
+ };
+
+ pin_gpio_g7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "RST_BMC_PCIE_I2CMUX_N";
+ };
+
+ pin_gpio_h2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PSU1_FFS_N_R";
+ };
+
+ pin_gpio_h3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PSU2_FFS_N_R";
+ };
+
+ pin_gpio_i3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_INTRUDED_COVER";
+ };
+
+ pin_gpio_j2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_BIOS_UPDATE_N";
+ };
+
+ pin_gpio_j3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "RST_BMC_HDD_I2CMUX_N";
+ };
+
+ pin_gpio_s2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_VGA_SW";
+ };
+
+ pin_gpio_s4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
+ output;
+ line-name = "VBAT_EN_N";
+ };
+
+ pin_gpio_s6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PU_BMC_GPIOS6";
+ };
+
+ pin_gpio_y0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_NCSI_MUX_CTL_S0";
+ };
+
+ pin_gpio_y1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_NCSI_MUX_CTL_S1";
+ };
+
+ pin_gpio_z0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_RISER2_INT_N";
+ };
+
+ pin_gpio_z2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_RISER2_RESET_N";
+ };
+
+ pin_gpio_z3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "FM_BMC_PCH_SCI_LPC_N";
+ };
+
+ pin_gpio_z7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_POST_CMPLT_N";
+ };
+
+ pin_gpio_aa0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "HOST_BMC_USB_SEL";
+ };
+
+ pin_gpio_aa5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_BUS1_RST_OUT_N";
+ };
+
+};
--
2.7.4
next reply other threads:[~2019-05-05 6:08 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-05 6:08 Andrew Peng [this message]
2019-05-06 3:17 ` [PATCH v6] ARM: dts: aspeed: Adding Lenovo Hr630 BMC Andrew Jeffery
2019-05-06 14:38 ` Patrick Venture
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1557036518-286348-1-git-send-email-pengms1@lenovo.com \
--to=pengms1@lenovo.com \
--cc=linux-aspeed@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox