[PATCH AUTOSEL 4.19 528/671] ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit

[PATCH AUTOSEL 4.19 528/671] ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit

[Sasha Levin]

From: Oscar A Perez <linux@neuralgames.com>

[ Upstream commit 89b97c429e2e77d695b5133572ca12ec256a4ea4 ]

According to the AST2500/AST2520 specs, these SoCs support up to 228 GPIO
pins. However, 'gpio-ranges' value in 'aspeed-g5.dtsi' file is currently
setting the upper limit to 220 which isn't allowing access to all their
GPIOs. The correct upper limit value is 232 (actual number is 228 plus a
4-GPIO hole in GPIOAB). Without this patch, GPIOs AC5 and AC6 do not work
correctly on a AST2500 BMC running Linux Kernel v4.19

Fixes: 2039f90d136c ("ARM: dts: aspeed-g5: Add gpio controller to devicetree")
Signed-off-by: Oscar A Perez <linux@neuralgames.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/aspeed-g5.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi
index d107459fc0f8..f2e1015d75ab 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@@ -247,7 +247,7 @@
 				compatible = "aspeed,ast2500-gpio";
 				reg = <0x1e780000 0x1000>;
 				interrupts = <20>;
-				gpio-ranges = <&pinctrl 0 0 220>;
+				gpio-ranges = <&pinctrl 0 0 232>;
 				clocks = <&syscon ASPEED_CLK_APB>;
 				interrupt-controller;
 			};
-- 
2.20.1

[PATCH AUTOSEL 4.19 547/671] gpio/aspeed: Fix incorrect number of banks

[Sasha Levin]

From: Rashmica Gupta <rashmica.g@gmail.com>

[ Upstream commit 3c4710ae6f883f9c6e3df5e27e274702a1221c57 ]

The current calculation for the number of GPIO banks is only correct if
the number of GPIOs is a multiple of 32 (if there were 31 GPIOs we would
currently say there are 0 banks, which is incorrect).

Fixes: 361b79119a4b7 ('gpio: Add Aspeed driver')

Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190906062623.13354-1-rashmica.g at gmail.com
Reviewed-by: Joel Stanley <joel@jms.d.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-aspeed.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpio/gpio-aspeed.c b/drivers/gpio/gpio-aspeed.c
index b696ec35efb3..e627e0e9001a 100644
--- a/drivers/gpio/gpio-aspeed.c
+++ b/drivers/gpio/gpio-aspeed.c
@@ -1199,7 +1199,7 @@ static int __init aspeed_gpio_probe(struct platform_device *pdev)
 	gpio->chip.irq.need_valid_mask = true;
 
 	/* Allocate a cache of the output registers */
-	banks = gpio->config->nr_gpios >> 5;
+	banks = DIV_ROUND_UP(gpio->config->nr_gpios, 32);
 	gpio->dcache = devm_kcalloc(&pdev->dev,
 				    banks, sizeof(u32), GFP_KERNEL);
 	if (!gpio->dcache)
-- 
2.20.1

[PATCH AUTOSEL 4.19 667/671] soc: aspeed: Fix snoop_file_poll()'s return type

[Sasha Levin]

From: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>

[ Upstream commit a4e55ccd4392e70f296d12e81b93c6ca96ee21d5 ]

snoop_file_poll() is defined as returning 'unsigned int' but the
.poll method is declared as returning '__poll_t', a bitwise type.

Fix this by using the proper return type and using the EPOLL
constants instead of the POLL ones, as required for __poll_t.

Link: https://lore.kernel.org/r/20191121051851.268726-1-joel at jms.id.au
Fixes: 3772e5da4454 ("drivers/misc: Aspeed LPC snoop output using misc chardev")
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/misc/aspeed-lpc-snoop.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/misc/aspeed-lpc-snoop.c b/drivers/misc/aspeed-lpc-snoop.c
index 2feb4347d67f..c10be21a1663 100644
--- a/drivers/misc/aspeed-lpc-snoop.c
+++ b/drivers/misc/aspeed-lpc-snoop.c
@@ -101,13 +101,13 @@ static ssize_t snoop_file_read(struct file *file, char __user *buffer,
 	return ret ? ret : copied;
 }
 
-static unsigned int snoop_file_poll(struct file *file,
+static __poll_t snoop_file_poll(struct file *file,
 				    struct poll_table_struct *pt)
 {
 	struct aspeed_lpc_snoop_channel *chan = snoop_file_to_chan(file);
 
 	poll_wait(file, &chan->wq, pt);
-	return !kfifo_is_empty(&chan->fifo) ? POLLIN : 0;
+	return !kfifo_is_empty(&chan->fifo) ? EPOLLIN : 0;
 }
 
 static const struct file_operations snoop_fops = {
-- 
2.20.1