* [PATCH v6 0/2] ARM: dts: Add support for Meta Clemente BMC
@ 2025-07-08 10:17 Leo Wang
2025-07-08 10:18 ` [PATCH v6 1/2] dt-bindings: arm: aspeed: add Meta Clemente board Leo Wang
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Leo Wang @ 2025-07-08 10:17 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, Kees Cook, Tony Luck, Guilherme G. Piccoli,
Geert Uytterhoeven, Magnus Damm
Cc: devicetree, linux-arm-kernel, linux-aspeed, linux-kernel,
linux-hardening, linux-renesas-soc, Leo Wang
This series adds initial support for the Meta Clemente BMC based on the
ASPEED AST2600 SoC.
Patch 1 documents the compatible string.
Patch 2 adds the device tree for the board.
Signed-off-by: Leo Wang <leo.jt.wang@gmail.com>
---
Changes in v6:
- Correct Author email to match Signed-off-by email address.
- Link to v5: https://lore.kernel.org/r/20250627-add-support-for-meta-clemente-bmc-v5-0-038ed6f1cb9f@fii-foxconn.com
Changes in v5:
- Remove accidentally pasted texts.
- Link to v4: https://lore.kernel.org/r/20250627-add-support-for-meta-clemente-bmc-v4-0-ce7ff23460c4@fii-foxconn.com
Changes in v4:
- Move properties of nodes defined in the same file from label ref back to where they belong.
- Move pinctrl default configs for ncsi3 and ncsi4 to aspeed-g6-pinctrl.dtsi.
- Add properties to i2c10 and i2c15 to enable MCTP.
- Link to v3: https://lore.kernel.org/r/20250623-add-support-for-meta-clemente-bmc-v3-0-c223ffcf46cf@fii-foxconn.com
Changes in v3:
- Modify leakage sensor to reflect current design.
- Link to v2: https://lore.kernel.org/r/20250621-add-support-for-meta-clemente-bmc-v2-0-6c5ef059149c@fii-foxconn.com
Changes in v2:
- Fix patch 1/2 subject line to match dt-bindings convention.
- Reorder device tree nodes in patch 2/2 to follow upstream DTS style.
- Link to v1: https://lore.kernel.org/r/20250618-add-support-for-meta-clemente-bmc-v1-0-e5ca669ee47b@fii-foxconn.com
---
Leo Wang (2):
dt-bindings: arm: aspeed: add Meta Clemente board
ARM: dts: aspeed: clemente: add Meta Clemente BMC
.../devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../dts/aspeed/aspeed-bmc-facebook-clemente.dts | 1291 ++++++++++++++++++++
arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi | 11 +
4 files changed, 1304 insertions(+)
---
base-commit: 52da431bf03b5506203bca27fe14a97895c80faf
change-id: 20250618-add-support-for-meta-clemente-bmc-941a469bc523
Best regards,
--
Leo Wang <leo.jt.wang@fii-foxconn.com>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v6 1/2] dt-bindings: arm: aspeed: add Meta Clemente board
2025-07-08 10:17 [PATCH v6 0/2] ARM: dts: Add support for Meta Clemente BMC Leo Wang
@ 2025-07-08 10:18 ` Leo Wang
2025-07-08 12:25 ` Rob Herring (Arm)
2025-07-08 10:18 ` [PATCH v6 2/2] ARM: dts: aspeed: clemente: add Meta Clemente BMC Leo Wang
2025-07-08 13:23 ` [PATCH v6 0/2] ARM: dts: Add support for " Rob Herring (Arm)
2 siblings, 1 reply; 5+ messages in thread
From: Leo Wang @ 2025-07-08 10:18 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, Kees Cook, Tony Luck, Guilherme G. Piccoli,
Geert Uytterhoeven, Magnus Damm
Cc: devicetree, linux-arm-kernel, linux-aspeed, linux-kernel,
linux-hardening, linux-renesas-soc, Leo Wang
From: Leo Wang <leo.jt.wang@gmail.com>
Document the new compatibles used on Meta Clemente.
Signed-off-by: Leo Wang <leo.jt.wang@gmail.com>
---
Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index 01333ac111fbb076582a6c0e801903c3500b459f..ff3fea63cecd99ec2dc56d3cf71403f897681a98 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -81,6 +81,7 @@ properties:
- asus,x4tf-bmc
- facebook,bletchley-bmc
- facebook,catalina-bmc
+ - facebook,clemente-bmc
- facebook,cloudripper-bmc
- facebook,elbert-bmc
- facebook,fuji-bmc
--
2.43.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v6 2/2] ARM: dts: aspeed: clemente: add Meta Clemente BMC
2025-07-08 10:17 [PATCH v6 0/2] ARM: dts: Add support for Meta Clemente BMC Leo Wang
2025-07-08 10:18 ` [PATCH v6 1/2] dt-bindings: arm: aspeed: add Meta Clemente board Leo Wang
@ 2025-07-08 10:18 ` Leo Wang
2025-07-08 13:23 ` [PATCH v6 0/2] ARM: dts: Add support for " Rob Herring (Arm)
2 siblings, 0 replies; 5+ messages in thread
From: Leo Wang @ 2025-07-08 10:18 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, Kees Cook, Tony Luck, Guilherme G. Piccoli,
Geert Uytterhoeven, Magnus Damm
Cc: devicetree, linux-arm-kernel, linux-aspeed, linux-kernel,
linux-hardening, linux-renesas-soc, Leo Wang
From: Leo Wang <leo.jt.wang@gmail.com>
Add linux device tree entry for Meta Clemente compute-tray
BMC using AST2600 SoC.
Signed-off-by: Leo Wang <leo.jt.wang@gmail.com>
---
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../dts/aspeed/aspeed-bmc-facebook-clemente.dts | 1291 ++++++++++++++++++++
arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi | 11 +
3 files changed, 1303 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index 2e5f4833a073b6c25190fd4b6e89a11f9636fc84..904503f78f960d7bc14cad7cb455bb8bb3138ccd 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-delta-ahe50dc.dtb \
aspeed-bmc-facebook-bletchley.dtb \
aspeed-bmc-facebook-catalina.dtb \
+ aspeed-bmc-facebook-clemente.dtb \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-elbert.dtb \
aspeed-bmc-facebook-fuji.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts
new file mode 100644
index 0000000000000000000000000000000000000000..aa67f118b94ee8bc3ec82b2c52af7864223c9f23
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts
@@ -0,0 +1,1291 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+ model = "Facebook Clemente BMC";
+ compatible = "facebook,clemente-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial0 = &uart1;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ i2c16 = &i2c1mux0ch0;
+ i2c17 = &i2c1mux0ch1;
+ i2c18 = &i2c1mux0ch2;
+ i2c19 = &i2c1mux0ch3;
+ i2c20 = &i2c1mux0ch4;
+ i2c21 = &i2c1mux0ch5;
+ i2c22 = &i2c1mux0ch6;
+ i2c23 = &i2c1mux0ch7;
+ i2c24 = &i2c0mux0ch0;
+ i2c25 = &i2c0mux0ch1;
+ i2c26 = &i2c0mux0ch2;
+ i2c27 = &i2c0mux0ch3;
+ i2c28 = &i2c0mux1ch0;
+ i2c29 = &i2c0mux1ch1;
+ i2c30 = &i2c0mux1ch2;
+ i2c31 = &i2c0mux1ch3;
+ i2c32 = &i2c0mux2ch0;
+ i2c33 = &i2c0mux2ch1;
+ i2c34 = &i2c0mux2ch2;
+ i2c35 = &i2c0mux2ch3;
+ i2c36 = &i2c0mux3ch0;
+ i2c37 = &i2c0mux3ch1;
+ i2c38 = &i2c0mux3ch2;
+ i2c39 = &i2c0mux3ch3;
+ i2c40 = &i2c0mux4ch0;
+ i2c41 = &i2c0mux4ch1;
+ i2c42 = &i2c0mux4ch2;
+ i2c43 = &i2c0mux4ch3;
+ i2c44 = &i2c0mux5ch0;
+ i2c45 = &i2c0mux5ch1;
+ i2c46 = &i2c0mux5ch2;
+ i2c47 = &i2c0mux5ch3;
+ i2c48 = &i2c0mux0ch1mux0ch0;
+ i2c49 = &i2c0mux0ch1mux0ch1;
+ i2c50 = &i2c0mux0ch1mux0ch2;
+ i2c51 = &i2c0mux0ch1mux0ch3;
+ i2c52 = &i2c0mux3ch1mux0ch0;
+ i2c53 = &i2c0mux3ch1mux0ch1;
+ i2c54 = &i2c0mux3ch1mux0ch2;
+ i2c55 = &i2c0mux3ch1mux0ch3;
+ };
+
+ chosen {
+ stdout-path = "serial4:57600n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+ <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+ <&adc1 2>;
+ };
+
+ spi1_gpio: spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+ miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+ num-chipselects = <1>;
+
+ tpm@0 {
+ compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+ spi-max-frequency = <33000000>;
+ reg = <0>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "bmc_heartbeat_amber";
+ gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-1 {
+ label = "fp_id_amber";
+ default-state = "off";
+ gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "bmc_ready_noled";
+ gpios = <&gpio0 ASPEED_GPIO(B, 3) (GPIO_ACTIVE_HIGH|GPIO_TRANSITORY)>;
+ };
+
+ led-3 {
+ label = "bmc_ready_cpld_noled";
+ gpios = <&gpio0 ASPEED_GPIO(P, 5) (GPIO_ACTIVE_HIGH|GPIO_TRANSITORY)>;
+ };
+ };
+
+ p1v8_bmc_aux: regulator-p1v8-bmc-aux {
+ compatible = "regulator-fixed";
+ regulator-name = "p1v8_bmc_aux";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ p2v5_bmc_aux: regulator-p2v5-bmc-aux {
+ compatible = "regulator-fixed";
+ regulator-name = "p2v5_bmc_aux";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ ramoops@b3e00000 {
+ compatible = "ramoops";
+ reg = <0xbb000000 0x200000>; /* 16 * (4 * 0x8000) */
+ record-size = <0x8000>;
+ console-size = <0x8000>;
+ ftrace-size = <0x8000>;
+ pmsg-size = <0x8000>;
+ max-reason = <3>;
+ };
+ };
+
+};
+
+&adc0 {
+ vref-supply = <&p1v8_bmc_aux>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+ &pinctrl_adc2_default &pinctrl_adc3_default
+ &pinctrl_adc4_default &pinctrl_adc5_default
+ &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ vref-supply = <&p2v5_bmc_aux>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc10_default>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+ };
+ flash@1 {
+ status = "okay";
+ m25p,fast-read;
+ label = "alt-bmc";
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0-A7*/ "","","","","","","","",
+ /*B0-B7*/ "BATTERY_DETECT","PRSNT1_HPM_SCM_N",
+ "BMC_I2C1_FPGA_ALERT_L","BMC_READY",
+ "IOEXP_INT_L","FM_ID_LED",
+ "","",
+ /*C0-C7*/ "BMC_GPIOC0","","","",
+ "PMBUS_REQ_N","PSU_FW_UPDATE_REQ_N",
+ "","BMC_I2C_SSIF_ALERT_L",
+ /*D0-D7*/ "","","","","BMC_GPIOD4","","","",
+ /*E0-E7*/ "BMC_GPIOE0","BMC_GPIOE1","","","","","","",
+ /*F0-F7*/ "","","","","","","","",
+ /*G0-G7*/ "","","","","","",
+ "FM_DEBUG_PORT_PRSNT_N","FM_BMC_DBP_PRESENT_N",
+ /*H0-H7*/ "PWR_BRAKE_L","RUN_POWER_EN",
+ "SHDN_FORCE_L","SHDN_REQ_L",
+ "","","","",
+ /*I0-I7*/ "","","","",
+ "","FLASH_WP_STATUS",
+ "FM_PDB_HEALTH_N","RUN_POWER_PG",
+ /*J0-J7*/ "","","","","","","","",
+ /*K0-K7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","","","",
+ /*M0-M7*/ "PCIE_EP_RST_EN","BMC_FRU_WP",
+ "SCM_HPM_STBY_RST_N","SCM_HPM_STBY_EN",
+ "STBY_POWER_PG_3V3","TH500_SHDN_OK_L","","",
+ /*N0-N7*/ "LED_POSTCODE_0","LED_POSTCODE_1",
+ "LED_POSTCODE_2","LED_POSTCODE_3",
+ "LED_POSTCODE_4","LED_POSTCODE_5",
+ "LED_POSTCODE_6","LED_POSTCODE_7",
+ /*O0-O7*/ "HMC_I2C3_FPGA_ALERT_L","FPGA_READY_HMC",
+ "CHASSIS_AC_LOSS_L","BSM_PRSNT_R_N",
+ "PSU_SMB_ALERT_L","FM_TPM_PRSNT_0_N",
+ "","USBDBG_IPMI_EN_L",
+ /*P0-P7*/ "PWR_BTN_BMC_N","IPEX_CABLE_PRSNT_L",
+ "ID_RST_BTN_BMC_N","RST_BMC_RSTBTN_OUT_N",
+ "host0-ready","BMC_READY_CPLD","BMC_GPIOP6","BMC_HEARTBEAT_N",
+ /*Q0-Q7*/ "IRQ_PCH_TPM_SPI_N","USB_OC0_REAR_R_N",
+ "UART_MUX_SEL","I2C_MUX_RESET_L",
+ "RSVD_NV_PLT_DETECT","SPI_TPM_INT_L",
+ "CPU_JTAG_MUX_SELECT","THERM_BB_OVERT_L",
+ /*R0-R7*/ "THERM_BB_WARN_L","SPI_BMC_FPGA_INT_L",
+ "CPU_BOOT_DONE","PMBUS_GNT_L",
+ "CHASSIS_PWR_BRK_L","PCIE_WAKE_L",
+ "PDB_THERM_OVERT_L","HMC_I2C2_FPGA_ALERT_L",
+ /*S0-S7*/ "","","SYS_BMC_PWRBTN_R_N","FM_TPM_PRSNT_1_N",
+ "FM_BMC_DEBUG_SW_N","UID_LED_N",
+ "SYS_FAULT_LED_N","RUN_POWER_FAULT_L",
+ /*T0-T7*/ "","","","","","","","",
+ /*U0-U7*/ "","","","","","","","",
+ /*V0-V7*/ "L2_RST_REQ_OUT_L","L0L1_RST_REQ_OUT_L",
+ "BMC_ID_BEEP_SEL","BMC_I2C0_FPGA_ALERT_L",
+ "SMB_BMC_TMP_ALERT","PWR_LED_N",
+ "SYS_RST_OUT_L","IRQ_TPM_SPI_N",
+ /*W0-W7*/ "","","","","","","","",
+ /*X0-X7*/ "","","","","","","","",
+ /*Y0-Y7*/ "","RST_BMC_SELF_HW",
+ "FM_FLASH_LATCH_N","BMC_EMMC_RST_N",
+ "BMC_GPIOY4","BMC_GPIOY5","","",
+ /*Z0-Z7*/ "","","","","","","BMC_GPIOZ6","BMC_GPIOZ7";
+};
+
+&gpio1 {
+ gpio-line-names =
+ /*18A0-18A7*/ "","","","","","","","",
+ /*18B0-18B3*/ "","","","",
+ /*18B4-18B7*/ "FM_BOARD_BMC_REV_ID0","FM_BOARD_BMC_REV_ID1","FM_BOARD_BMC_REV_ID2","",
+ /*18C0-18C7*/ "","","PI_BMC_BIOS_ROM_IRQ0_N","","","","","",
+ /*18D0-18D7*/ "","","","","","","","",
+ /*18E0-18E3*/ "","","","AC_PWR_BMC_BTN_N","","","","";
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux@71 {
+ compatible = "nxp,pca9546";
+ reg = <0x71>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux0ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ // IOB0 NIC0 TEMP
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
+ i2c0mux0ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ // HDD FRU EEPROM
+ eeprom@56 {
+ compatible = "atmel,24c128";
+ reg = <0x56>;
+ };
+
+ // E1.S Backplane
+ i2c0mux0ch1mux0: i2c-mux@74 {
+ compatible = "nxp,pca9546";
+ reg = <0x74>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux0ch1mux0ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ i2c0mux0ch1mux0ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ i2c0mux0ch1mux0ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+ i2c0mux0ch1mux0ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+ i2c0mux0ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ // IOB0 NIC1 TEMP
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
+ i2c0mux0ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@72 {
+ compatible = "nxp,pca9546";
+ reg = <0x72>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux1ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ i2c0mux1ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ // IO Mezz 0 IOEXP
+ io_expander7: gpio@20 {
+ compatible = "nxp,pca9535";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "RST_CX7_0",
+ "RST_CX7_1",
+ "CX0_SSD0_PRSNT_L",
+ "CX1_SSD1_PRSNT_L",
+ "CX_BOOT_CMPLT_CX0",
+ "CX_BOOT_CMPLT_CX1",
+ "CX_TWARN_CX0_L",
+ "CX_TWARN_CX1_L",
+ "CX_OVT_SHDN_CX0",
+ "CX_OVT_SHDN_CX1",
+ "FNP_L_CX0",
+ "FNP_L_CX1",
+ "",
+ "MCU_GPIO",
+ "MCU_RST_N",
+ "MCU_RECOVERY_N";
+ };
+
+ // IO Mezz 0 FRU EEPROM
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+
+ // OSFP 0 FRU EEPROM
+ eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ };
+ };
+ i2c0mux1ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+ i2c0mux1ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@73 {
+ compatible = "nxp,pca9546";
+ reg = <0x73>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux2ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ i2c0mux2ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ i2c0mux2ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+ i2c0mux2ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9546";
+ reg = <0x75>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux3ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ // IOB1 NIC0 TEMP
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
+ i2c0mux3ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ // E1.S Backplane HDD FRU EEPROM
+ eeprom@56 {
+ compatible = "atmel,24c128";
+ reg = <0x56>;
+ };
+
+ // E1.S Backplane MUX
+ i2c0mux3ch1mux0: i2c-mux@74 {
+ compatible = "nxp,pca9546";
+ reg = <0x74>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux3ch1mux0ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ i2c0mux3ch1mux0ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ i2c0mux3ch1mux0ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+ i2c0mux3ch1mux0ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+ i2c0mux3ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ // IOB1 NIC1 TEMP
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
+ i2c0mux3ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@76 {
+ compatible = "nxp,pca9546";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux4ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ i2c0mux4ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ // IO Mezz 1 IOEXP
+ io_expander8: gpio@21 {
+ compatible = "nxp,pca9535";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "SEC_RST_CX7_0",
+ "SEC_RST_CX7_1",
+ "SEC_CX0_SSD0_PRSNT_L",
+ "SEC_CX1_SSD1_PRSNT_L",
+ "SEC_CX_BOOT_CMPLT_CX0",
+ "SEC_CX_BOOT_CMPLT_CX1",
+ "SEC_CX_TWARN_CX0_L",
+ "SEC_CX_TWARN_CX1_L",
+ "SEC_CX_OVT_SHDN_CX0",
+ "SEC_CX_OVT_SHDN_CX1",
+ "SEC_FNP_L_CX0",
+ "SEC_FNP_L_CX1",
+ "",
+ "SEC_MCU_GPIO",
+ "SEC_MCU_RST_N",
+ "SEC_MCU_RECOVERY_N";
+ };
+
+ // IO Mezz 1 FRU EEPROM
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+
+ // OSFP 1 FRU EEPROM
+ eeprom@52 {
+ compatible = "atmel,24c128";
+ reg = <0x52>;
+ };
+ };
+ i2c0mux4ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+ i2c0mux4ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9546";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect;
+
+ i2c0mux5ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+ i2c0mux5ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ i2c0mux5ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+ i2c0mux5ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ // PDB
+ power-monitor@12 {
+ compatible = "ti,lm5066i";
+ reg = <0x12>;
+ };
+
+ // PDB
+ power-monitor@14 {
+ compatible = "ti,lm5066i";
+ reg = <0x14>;
+ };
+
+ // Module 0
+ fanctl0: fan-controller@20{
+ compatible = "maxim,max31790";
+ reg = <0x20>;
+ };
+
+ // Module 0
+ fanctl1: fan-controller@23{
+ compatible = "maxim,max31790";
+ reg = <0x23>;
+ };
+
+ // Module 1
+ fanctl2: fan-controller@2c{
+ compatible = "maxim,max31790";
+ reg = <0x2c>;
+ };
+
+ // Module 1
+ fanctl3: fan-controller@2f{
+ compatible = "maxim,max31790";
+ reg = <0x2f>;
+ };
+
+ // Module 0 Leak Sensor
+ adc@34 {
+ compatible = "maxim,max1363";
+ reg = <0x34>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@0 {
+ reg = <0>;
+ ti,gain = <2>;
+ };
+
+ channel@1 {
+ reg = <1>;
+ ti,gain = <2>;
+ };
+
+ channel@2 {
+ reg = <2>;
+ ti,gain = <2>;
+ };
+
+ channel@3 {
+ reg = <3>;
+ ti,gain = <2>;
+ };
+ };
+
+ // Module 1 Leak Sensor
+ adc@35 {
+ compatible = "maxim,max1363";
+ reg = <0x35>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@0 {
+ reg = <0>;
+ ti,gain = <2>;
+ };
+
+ channel@1 {
+ reg = <1>;
+ ti,gain = <2>;
+ };
+
+ channel@2 {
+ reg = <2>;
+ ti,gain = <2>;
+ };
+
+ channel@3 {
+ reg = <3>;
+ ti,gain = <2>;
+ };
+ };
+
+// PDB TEMP SENSOR
+ temperature-sensor@4e {
+ compatible = "ti,tmp1075";
+ reg = <0x4e>;
+ };
+
+ // PDB FRU EEPROM
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ };
+
+ // PDB
+ vrm@60 {
+ compatible = "renesas,raa228004";
+ reg = <0x60>;
+ };
+
+ // PDB
+ vrm@61 {
+ compatible = "renesas,raa228004";
+ reg = <0x61>;
+ };
+
+ // Interposer
+ i2c-mux@70 {
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ i2c1mux0ch0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+ };
+ i2c1mux0ch1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+ };
+ i2c1mux0ch2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+ };
+ i2c1mux0ch3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+ };
+ i2c1mux0ch4: i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+ };
+ i2c1mux0ch5: i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x5>;
+
+ // Interposer TEMP SENSOR
+ temperature-sensor@4f {
+ compatible = "ti,tmp75";
+ reg = <0x4f>;
+ };
+
+ // Interposer FRU EEPROM
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+ };
+ i2c1mux0ch6: i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6>;
+
+ // Interposer IOEXP
+ io_expander5: gpio@27 {
+ compatible = "nxp,pca9554";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "JTAG_MUX_SEL",
+ "IOX_BMC_RESET",
+ "RTC_CLR_L",
+ "RTC_U77_ALRT_N",
+ "",
+ "PSU_ALERT_N",
+ "",
+ "RST_P12V_STBY_N";
+ };
+ };
+ i2c1mux0ch7: i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x7>;
+
+ // FIO TEMP SENSOR
+ temperature-sensor@4b {
+ compatible = "ti,tmp75";
+ reg = <0x4b>;
+ };
+
+ // FIO FRU EEPROM
+ eeprom@51 {
+ compatible = "atmel,24c64";
+ reg = <0x51>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ // Module 0, Expander @0x20
+ io_expander0: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "FPGA_THERM_OVERT_L-I",
+ "FPGA_READY_BMC-I",
+ "HMC_BMC_DETECT-O",
+ "HMC_PGOOD-O",
+ "",
+ "BMC_STBY_CYCLE-O",
+ "FPGA_EROT_FATAL_ERROR_L-I",
+ "WP_HW_EXT_CTRL_L-O",
+ "EROT_FPGA_RST_L-O",
+ "FPGA_EROT_RECOVERY_L-O",
+ "BMC_EROT_FPGA_SPI_MUX_SEL-O",
+ "USB2_HUB_RST_L-O",
+ "",
+ "SGPIO_EN_L-O",
+ "B2B_IOEXP_INT_L-I",
+ "I2C_BUS_MUX_RESET_L-O";
+ };
+
+ // Module 1, Expander @0x21
+ io_expander1: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "SEC_FPGA_THERM_OVERT_L",
+ "SEC_FPGA_READY_BMC",
+ "SEC_HMC_BMC_DETECT",
+ "SEC_HMC_PGOOD",
+ "",
+ "SEC_BMC_SELF_POWER_CYCLE",
+ "SEC_SEC_FPGA_EROT_FATAL_ERROR_L",
+ "SEC_WP_HW_EXT_CTRL_L",
+ "SEC_EROT_FPGA_RST_L",
+ "SEC_FPGA_EROT_RECOVERY_L",
+ "SEC_BMC_EROT_FPGA_SPI_MUX_SEL",
+ "SEC_USB2_HUB_RST_L",
+ "",
+ "SEC_SGPIO_EN_L",
+ "SEC_IOB_IOEXP_INT_L",
+ "SEC_I2C_BUS_MUX_RESET_L";
+ };
+
+ // HMC Expander @0x27
+ io_expander2: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "HMC_PRSNT_L-I",
+ "HMC_READY-I",
+ "HMC_EROT_FATAL_ERROR_L-I",
+ "I2C_MUX_SEL-O",
+ "HMC_EROT_SPI_MUX_SEL-O",
+ "HMC_EROT_RECOVERY_L-O",
+ "HMC_EROT_RST_L-O",
+ "GLOBAL_WP_HMC-O",
+ "FPGA_RST_L-O",
+ "USB2_HUB_RST-O",
+ "CPU_UART_MUX_SEL-O",
+ "",
+ "",
+ "",
+ "",
+ "";
+ };
+
+ // Module 0 Aux EEPROM
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+
+ // Module 1 Aux EEPROM
+ eeprom@51 {
+ compatible = "atmel,24c64";
+ reg = <0x51>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+ io_expander3: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "RTC_MUX_SEL",
+ "PCI_MUX_SEL",
+ "TPM_MUX_SEL",
+ "FAN_MUX-SEL",
+ "SGMII_MUX_SEL",
+ "DP_MUX_SEL",
+ "UPHY3_USB_SEL",
+ "NCSI_MUX_SEL",
+ "BMC_PHY_RST",
+ "RTC_CLR_L",
+ "BMC_12V_CTRL",
+ "PS_RUN_IO0_PG",
+ "",
+ "",
+ "",
+ "";
+ };
+
+ rtc@6f {
+ compatible = "nuvoton,nct3018y";
+ reg = <0x6f>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+};
+
+&i2c8 {
+ status = "okay";
+};
+
+&i2c9 {
+ status = "okay";
+ // SCM TEMP SENSOR BOARD
+ temperature-sensor@4b {
+ compatible = "national,lm75b";
+ reg = <0x4b>;
+ };
+
+ // SCM CPLD IOEXP
+ io_expander4: gpio@4f {
+ compatible = "nxp,pca9555";
+ reg = <0x4f>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "stby_power_en_cpld",
+ "stby_power_gd_cpld",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "";
+ };
+
+ // SCM FRU EEPROM
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+
+ // BSM FRU EEPROM
+ eeprom@56 {
+ compatible = "atmel,24c64";
+ reg = <0x56>;
+ };
+};
+
+&i2c10 {
+ status = "okay";
+ multi-master;
+ mctp-controller;
+ mctp@10 {
+ compatible = "mctp-i2c-controller";
+ reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+ };
+
+ // OCP NIC0 TEMP
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+
+ // OCP NIC0 FRU EEPROM
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+};
+
+&i2c11 {
+ status = "okay";
+ ssif-bmc@10 {
+ compatible = "ssif-bmc";
+ reg = <0x10>;
+ };
+};
+
+&i2c12 {
+ status = "okay";
+ multi-master;
+};
+
+&i2c13 {
+ status = "okay";
+ multi-master;
+
+ // HPM FRU EEPROM
+ eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+ // CBC 0 FRU
+ eeprom@54 {
+ compatible = "atmel,24c02";
+ reg = <0x54>;
+ };
+ // CBC 1 FRU
+ eeprom@55 {
+ compatible = "atmel,24c02";
+ reg = <0x55>;
+ };
+ // CBC 2 FRU
+ eeprom@56 {
+ compatible = "atmel,24c02";
+ reg = <0x56>;
+ };
+ // HMC FRU EEPROM
+ eeprom@57 {
+ compatible = "atmel,24c02";
+ reg = <0x57>;
+ };
+ // CBC 3 FRU
+ eeprom@58 {
+ compatible = "atmel,24c02";
+ reg = <0x58>;
+ };
+};
+
+&i2c14 {
+ status = "okay";
+
+ // PDB CPLD IOEXP 0x10
+ io_expander9: gpio@10 {
+ compatible = "nxp,pca9555";
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+ reg = <0x10>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "wSequence_Latch_State_N",
+ "wP12V_N1N2_RUNTIME_FLT_N",
+ "wP12V_FAN_RUNTIME_FLT_N",
+ "wP12V_AUX_RUNTIME_FLT_N",
+ "wHost_PERST_SEQPWR_FLT_N",
+ "wP12V_N1N2_SEQPWR_FLT_N",
+ "wP12V_FAN_SEQPWR_FLT_N",
+ "wP12V_AUX_SEQPWR_FLT_N",
+ "wP12V_RUNTIME_FLT_NIC1_N",
+ "wAUX_RUNTIME_FLT_NIC1_N",
+ "wP12V_SEQPWR_FLT_NIC1_N",
+ "wAUX_SEQPWR_FLT_NIC1_N",
+ "wP12V_RUNTIME_FLT_NIC0_N",
+ "wAUX_RUNTIME_FLT_NIC0_N",
+ "wP12V_SEQPWR_FLT_NIC0_N",
+ "wAUX_SEQPWR_FLT_NIC0_N";
+ };
+
+ // PDB CPLD IOEXP 0x11
+ io_expander10: gpio@11 {
+ compatible = "nxp,pca9555";
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+ reg = <0x11>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "FM_P12V_NIC1_FLTB_R_N",
+ "FM_P3V3_NIC1_FAULT_R_N",
+ "FM_P12V_NIC0_FLTB_R_N",
+ "FM_P3V3_NIC0_FAULT_R_N",
+ "P48V_HS2_FAULT_N_PLD",
+ "P48V_HS1_FAULT_N_PLD",
+ "P12V_AUX_FAN_OC_PLD_N",
+ "P12V_AUX_FAN_FAULT_PLD_N",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "FM_SYS_THROTTLE_N",
+ "OCP_V3_2_PWRBRK_FROM_HOST_ISO_PLD_N",
+ "OCP_SFF_PWRBRK_FROM_HOST_ISO_PLD_N";
+ };
+
+ // PDB CPLD IOEXP 0x12
+ io_expander11: gpio@12 {
+ compatible = "nxp,pca9555";
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+ reg = <0x12>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "P12V_AUX_PSU_SMB_ALERT_R_L",
+ "P12V_SCM_SENSE_ALERT_R_N",
+ "P12V_AUX_NIC1_SENSE_ALERT_R_N",
+ "P12V_AUX_NIC0_SENSE_ALERT_R_N",
+ "NODEB_PSU_SMB_ALERT_R_L",
+ "NODEA_PSU_SMB_ALERT_R_L",
+ "P12V_AUX_FAN_ALERT_PLD_N",
+ "P52V_SENSE_ALERT_PLD_N",
+ "PRSNT_RJ45_FIO_N_R",
+ "FM_MAIN_PWREN_RMC_EN_ISO_R",
+ "CHASSIS3_LEAK_Q_N_PLD",
+ "CHASSIS2_LEAK_Q_N_PLD",
+ "CHASSIS1_LEAK_Q_N_PLD",
+ "CHASSIS0_LEAK_Q_N_PLD",
+ "",
+ "SMB_RJ45_FIO_TMP_ALERT";
+ };
+
+ // PDB CPLD IOEXP 0x13
+ io_expander12: gpio@13 {
+ compatible = "nxp,pca9555";
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+ reg = <0x13>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "FAN_7_PRESENT_N",
+ "FAN_6_PRESENT_N",
+ "FAN_5_PRESENT_N",
+ "FAN_4_PRESENT_N",
+ "FAN_3_PRESENT_N",
+ "FAN_2_PRESENT_N",
+ "FAN_1_PRESENT_N",
+ "FAN_0_PRESENT_N",
+ "HP_LVC3_OCP_V3_2_PRSNT2_PLD_N",
+ "HP_LVC3_OCP_V3_1_PRSNT2_PLD_N",
+ "PRSNT_HDDBD_POWER_CABLE_N",
+ "PRSNT_OSFP0_POWER_CABLE_N",
+ "PRSNT_CHASSIS3_LEAK_CABLE_R_N",
+ "PRSNT_CHASSIS2_LEAK_CABLE_R_N",
+ "PRSNT_CHASSIS1_LEAK_CABLE_R_N",
+ "PRSNT_CHASSIS0_LEAK_CABLE_R_N";
+ };
+
+ // PDB CPLD IOEXP 0x14
+ io_expander13: gpio@14 {
+ compatible = "nxp,pca9555";
+ reg = <0x14>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "rmc_en_dc_pwr_on",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "leak_config_0",
+ "leak_config_1",
+ "leak_config_2",
+ "leak_config_3",
+ "mfg_led_test_mode_l",
+ "small_leak_err_inj",
+ "large_leak_err_inj",
+ "";
+ };
+};
+
+&i2c15 {
+ status = "okay";
+ multi-master;
+ mctp-controller;
+ mctp@10 {
+ compatible = "mctp-i2c-controller";
+ reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+ };
+
+ // OCP NIC1 TEMP
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+
+ // OCP NIC1 FRU EEPROM
+ eeprom@52 {
+ compatible = "atmel,24c64";
+ reg = <0x52>;
+ };
+};
+
+&mac2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ncsi3_default>;
+ use-ncsi;
+};
+
+&mac3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ncsi4_default>;
+ use-ncsi;
+};
+
+&udma {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&wdt1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdtrst1_default>;
+ aspeed,reset-type = "soc";
+ aspeed,external-signal;
+ aspeed,ext-push-pull;
+ aspeed,ext-active-high;
+ aspeed,ext-pulse-duration = <256>;
+};
+
diff --git a/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
index 289668f051eb4271ac48ae3ce9b82587911548ee..61b1d1c5040c820f8c995132739becde80e069bb 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
@@ -412,6 +412,16 @@ pinctrl_mdio4_default: mdio4_default {
groups = "MDIO4";
};
+ pinctrl_ncsi3_default: ncsi3_default {
+ function = "RMII3";
+ groups = "NCSI3";
+ };
+
+ pinctrl_ncsi4_default: ncsi4_default {
+ function = "RMII4";
+ groups = "NCSI4";
+ };
+
pinctrl_ncts1_default: ncts1_default {
function = "NCTS1";
groups = "NCTS1";
@@ -1192,3 +1202,4 @@ pinctrl_wdtrst4_default: wdtrst4_default {
groups = "WDTRST4";
};
};
+
--
2.43.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v6 1/2] dt-bindings: arm: aspeed: add Meta Clemente board
2025-07-08 10:18 ` [PATCH v6 1/2] dt-bindings: arm: aspeed: add Meta Clemente board Leo Wang
@ 2025-07-08 12:25 ` Rob Herring (Arm)
0 siblings, 0 replies; 5+ messages in thread
From: Rob Herring (Arm) @ 2025-07-08 12:25 UTC (permalink / raw)
To: Leo Wang
Cc: linux-hardening, Joel Stanley, Kees Cook, Geert Uytterhoeven,
linux-renesas-soc, Tony Luck, Andrew Jeffery,
Guilherme G. Piccoli, linux-arm-kernel, Krzysztof Kozlowski,
Conor Dooley, devicetree, linux-kernel, linux-aspeed, Magnus Damm
On Tue, 08 Jul 2025 18:18:00 +0800, Leo Wang wrote:
> From: Leo Wang <leo.jt.wang@gmail.com>
>
> Document the new compatibles used on Meta Clemente.
>
> Signed-off-by: Leo Wang <leo.jt.wang@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Please add Acked-by/Reviewed-by tags when posting new versions. However,
there's no need to repost patches *only* to add the tags. The upstream
maintainer will do that for acks received on the version they apply.
If a tag was not added on purpose, please state why and what changed.
Missing tags:
Acked-by: Conor Dooley <conor.dooley@microchip.com>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v6 0/2] ARM: dts: Add support for Meta Clemente BMC
2025-07-08 10:17 [PATCH v6 0/2] ARM: dts: Add support for Meta Clemente BMC Leo Wang
2025-07-08 10:18 ` [PATCH v6 1/2] dt-bindings: arm: aspeed: add Meta Clemente board Leo Wang
2025-07-08 10:18 ` [PATCH v6 2/2] ARM: dts: aspeed: clemente: add Meta Clemente BMC Leo Wang
@ 2025-07-08 13:23 ` Rob Herring (Arm)
2 siblings, 0 replies; 5+ messages in thread
From: Rob Herring (Arm) @ 2025-07-08 13:23 UTC (permalink / raw)
To: Leo Wang
Cc: Magnus Damm, linux-hardening, Geert Uytterhoeven,
Krzysztof Kozlowski, Guilherme G. Piccoli, devicetree,
Joel Stanley, Conor Dooley, Tony Luck, Andrew Jeffery,
linux-aspeed, linux-arm-kernel, Kees Cook, linux-kernel,
linux-renesas-soc
On Tue, 08 Jul 2025 18:17:59 +0800, Leo Wang wrote:
> This series adds initial support for the Meta Clemente BMC based on the
> ASPEED AST2600 SoC.
>
> Patch 1 documents the compatible string.
> Patch 2 adds the device tree for the board.
>
> Signed-off-by: Leo Wang <leo.jt.wang@gmail.com>
> ---
> Changes in v6:
> - Correct Author email to match Signed-off-by email address.
> - Link to v5: https://lore.kernel.org/r/20250627-add-support-for-meta-clemente-bmc-v5-0-038ed6f1cb9f@fii-foxconn.com
>
> Changes in v5:
> - Remove accidentally pasted texts.
> - Link to v4: https://lore.kernel.org/r/20250627-add-support-for-meta-clemente-bmc-v4-0-ce7ff23460c4@fii-foxconn.com
>
> Changes in v4:
> - Move properties of nodes defined in the same file from label ref back to where they belong.
> - Move pinctrl default configs for ncsi3 and ncsi4 to aspeed-g6-pinctrl.dtsi.
> - Add properties to i2c10 and i2c15 to enable MCTP.
> - Link to v3: https://lore.kernel.org/r/20250623-add-support-for-meta-clemente-bmc-v3-0-c223ffcf46cf@fii-foxconn.com
>
> Changes in v3:
> - Modify leakage sensor to reflect current design.
> - Link to v2: https://lore.kernel.org/r/20250621-add-support-for-meta-clemente-bmc-v2-0-6c5ef059149c@fii-foxconn.com
>
> Changes in v2:
> - Fix patch 1/2 subject line to match dt-bindings convention.
> - Reorder device tree nodes in patch 2/2 to follow upstream DTS style.
> - Link to v1: https://lore.kernel.org/r/20250618-add-support-for-meta-clemente-bmc-v1-0-e5ca669ee47b@fii-foxconn.com
>
> ---
> Leo Wang (2):
> dt-bindings: arm: aspeed: add Meta Clemente board
> ARM: dts: aspeed: clemente: add Meta Clemente BMC
>
> .../devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
> arch/arm/boot/dts/aspeed/Makefile | 1 +
> .../dts/aspeed/aspeed-bmc-facebook-clemente.dts | 1291 ++++++++++++++++++++
> arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi | 11 +
> 4 files changed, 1304 insertions(+)
> ---
> base-commit: 52da431bf03b5506203bca27fe14a97895c80faf
> change-id: 20250618-add-support-for-meta-clemente-bmc-941a469bc523
>
> Best regards,
> --
> Leo Wang <leo.jt.wang@fii-foxconn.com>
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
This patch series was applied (using b4) to base:
Base: using specified base-commit 52da431bf03b5506203bca27fe14a97895c80faf
If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)
New warnings running 'make CHECK_DTBS=y for arch/arm/boot/dts/aspeed/' for 20250708-add-support-for-meta-clemente-bmc-v6-0-7f3e57bd0336@fii-foxconn.com:
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: timer (arm,armv7-timer): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: bus@1e600000 (aspeed,ast2600-ahbc): compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: syscon@1e6e2000 (aspeed,ast2600-scu): 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^pinctrl-[0-9]+$', '^silicon-id@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: adc@1e6e9000 (aspeed,ast2600-adc0): 'interrupts' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: adc@1e6e9100 (aspeed,ast2600-adc1): 'interrupts' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: crypto@1e6fa000 (aspeed,ast2600-acry): 'aspeed,ahbc' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: lpc@1e789000 (aspeed,ast2600-lpc-v2): reg-io-width: 4 is not of type 'object'
from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: lpc@1e789000 (aspeed,ast2600-lpc-v2): lpc-snoop@80: 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: kcs@24 (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: kcs@28 (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: kcs@2c (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: kcs@114 (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: sdc@1e740000 (aspeed,ast2600-sd-controller): sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: sdc@1e740000 (aspeed,ast2600-sd-controller): sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: adc@34 (maxim,max1363): '#address-cells', '#size-cells', 'channel@0', 'channel@1', 'channel@2', 'channel@3' do not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/iio/adc/maxim,max1363.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: adc@35 (maxim,max1363): '#address-cells', '#size-cells', 'channel@0', 'channel@1', 'channel@2', 'channel@3' do not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/iio/adc/maxim,max1363.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: fsi@1e79b000 (aspeed,ast2600-fsi-master): compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: fsi@1e79b100 (aspeed,ast2600-fsi-master): compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dtb: /ahb/apb/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2025-07-12 3:11 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-07-08 10:17 [PATCH v6 0/2] ARM: dts: Add support for Meta Clemente BMC Leo Wang
2025-07-08 10:18 ` [PATCH v6 1/2] dt-bindings: arm: aspeed: add Meta Clemente board Leo Wang
2025-07-08 12:25 ` Rob Herring (Arm)
2025-07-08 10:18 ` [PATCH v6 2/2] ARM: dts: aspeed: clemente: add Meta Clemente BMC Leo Wang
2025-07-08 13:23 ` [PATCH v6 0/2] ARM: dts: Add support for " Rob Herring (Arm)
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).