Re: [PATCH v3 0/9] ARM: dts: aspeed: anacapa: restructure devicetree for development-phase

[Andrew Jeffery <andrew@codeconstruct.com.au>]

On Tue, 2026-06-02 at 21:24 +0800, Colin Huang via B4 Relay wrote:
> This series refactors the Anacapa BMC devicetree layout to better support
> development-phase hardware revisions (EVT1/EVT2/DVT) while keeping a platform
> entrypoint.
> 
> Signed-off-by: Colin Huang <u8813345@gmail.com>
> ---
> Changes in v3:
> - Restructure the EVT2 devicetree to inherit from the EVT1 devicetree, making it incremental rather than standalone.
> - Add the DVT devicetree, inheriting from the EVT2 devicetree.
> - Enable MCTP and FRU support for the NIC.
> - Align PDB fan GPIO numbering.
> - Add an EEPROM device node for the NFC adaptor board.
> - Add an additional EEPROM device node for the SCM.
> - Add shunt resistor values for HSC monitors
> - Link to v2: https://lore.kernel.org/r/20260409-anacapa-devlop-phase-devicetree-v2-0-68f328671653@gmail.com
> 

So just to check, the changes in patches 5-8 inclusive are applicable
to all of EVT1, EVT2 and DVT (given the way you've structured the
includes)?

> Changes in v2:
> - Fix dtbs_check fail.
>   Validated by following command:
>     make dt_binding_check DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml
>     make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa.dtb
>     make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa-evt1.dtb
>     make CHECK_DTBS=y DT_SCHEMA_FILES=arm/aspeed/aspeed.yaml aspeed/aspeed-bmc-facebook-anacapa-evt2.dtb
> - Link to v1: https://lore.kernel.org/r/20260407-anacapa-devlop-phase-devicetree-v1-0-97b96367cac3@gmail.com
> 
> ---
> Andy Chung (1):
>       ARM: dts: aspeed: anacapa: Enable MCTP and FRU for NIC
> 
> Carl Lee (1):
>       ARM: dts: aspeed: anacapa: Add eeprom device node for NFC adaptor board
> 
> Colin Huang (5):
>       dt-bindings: arm: aspeed: add Anacapa EVT1 EVT2 DVT board
>       ARM: dts: aspeed: anacapa: add EVT1 devicetree and point wrapper to it
>       ARM: dts: aspeed: anacapa: add EVT2 devicetree inheriting EVT1
>       ARM: dts: aspeed: anacapa: add DVT devicetree inheriting EVT2
>       ARM: dts: aspeed: anacapa: add additional EEPROM node for SCM

If you need to respin this series for some reason, can you please
capitalise the first word of the short description (the bit after the
last ':') for the commits above and the one below?

> 
> Peter Shen (1):
>       ARM: dts: aspeed: anacapa: evt2: add shunt resistor values for HSC monitors
> 
> Rex Fu (1):
>       ARM: dts: aspeed: anacapa: Align PDB fan GPIO numbering
> 
>  .../devicetree/bindings/arm/aspeed/aspeed.yaml     |    3 +
>  .../dts/aspeed/aspeed-bmc-facebook-anacapa-dvt.dts |  178 +++
>  .../aspeed/aspeed-bmc-facebook-anacapa-evt1.dts    | 1179 ++++++++++++++++++++
>  .../aspeed/aspeed-bmc-facebook-anacapa-evt2.dts    |  228 ++++
>  .../dts/aspeed/aspeed-bmc-facebook-anacapa.dts     | 1077 +-----------------
>  5 files changed, 1589 insertions(+), 1076 deletions(-)
> ---
> base-commit: 7ca1caf017d34396397b19fb4de9ecef256f4acc
> change-id: 20260407-anacapa-devlop-phase-devicetree-4101d3f312c0
> 
> Best regards,

Andrew