From: Alexander Stein <alexander.stein@ew.tq-group.com>
To: linux-aspeed@lists.ozlabs.org
Subject: [PATCH v2] ARM: dts: Fix undocumented LM75 compatible nodes
Date: Mon, 19 Aug 2024 11:43:51 +0200 [thread overview]
Message-ID: <4592015.LvFx2qVVIh@steina-w> (raw)
In-Reply-To: <20240816164717.1585629-1-robh@kernel.org>
Hi Rob,
thanks for the update.
Am Freitag, 16. August 2024, 18:47:14 CEST schrieb Rob Herring (Arm):
> "lm75" without any vendor is undocumented. It works with the Linux
> kernel since the I2C subsystem will do matches of the compatible string
> without a vendor prefix to the i2c_device_id and/or driver name.
>
> Mostly replace "lm75" with "national,lm75" as that's the original part
> vendor and the compatible which matches what "lm75" matched with. In a
> couple of cases the node name or compatible gives a clue to the actual
> part and vendor and a more specific compatible can be used. In these
> cases, it does change the variant the kernel picks.
>
> "nct75" is an OnSemi part which is compatible with TI TMP75C based on
> a comparison of the OnSemi NCT75 datasheet and configuration the Linux
> driver uses. Adding an OnSemi compatible would be an ABI change.
>
> "nxp,lm75" is most likely an NXP part. Alexander Stein says the i.MX53
> boards are a NXP LM75A as well. NXP makes a LM75A and LM75B. Both are
> 11-bit resolution and 100ms sample time. The "national,lm75a" is
> 9-bit, so "national,lm75b" is the closest match for both NXP variants.
>
> While we're here, fix the node names to use the generic name
> "temperature-sensor".
>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Kevin Hilman <khilman@baylibre.com> # am335x-nano.dts
> Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> # imx53-mba53.dts, imx53-tqma53.dtsi
> ---
> SoC maintainers, Please take this directly for v6.12.
>
> v2:
> - Also use "national,lm75b" on i.MX53 boards.
> ---
> .../aspeed/aspeed-bmc-facebook-greatlakes.dts | 2 +-
> .../socfpga/socfpga_cyclone5_vining_fpga.dts | 4 +--
> .../dts/marvell/armada-385-clearfog-gtr.dtsi | 8 ++---
> .../boot/dts/nuvoton/nuvoton-npcm730-kudo.dts | 32 +++++++++----------
> .../boot/dts/nuvoton/nuvoton-npcm750-evb.dts | 6 ++--
> arch/arm/boot/dts/nxp/imx/imx53-mba53.dts | 4 +--
> arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi | 4 +--
> .../dts/nxp/lpc/lpc4357-ea4357-devkit.dts | 4 +--
> .../boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts | 2 +-
> arch/arm/boot/dts/ti/omap/am335x-nano.dts | 2 +-
> .../boot/dts/xilinx/zynq-zturn-common.dtsi | 4 +--
> 11 files changed, 36 insertions(+), 36 deletions(-)
>
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts
> index 998598c15fd0..49914a4a179f 100644
> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts
> @@ -201,7 +201,7 @@ eeprom at 54 {
> &i2c12 {
> status = "okay";
> temperature-sensor at 4f {
> - compatible = "lm75";
> + compatible = "national,lm75";
> reg = <0x4f>;
> };
> };
> diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts
> index 65f390bf8975..84f39dec3c42 100644
> --- a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts
> +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts
> @@ -130,8 +130,8 @@ gpio: pca9557 at 1f {
> #gpio-cells = <2>;
> };
>
> - temp: lm75 at 48 {
> - compatible = "lm75";
> + temp: temperature-sensor at 48 {
> + compatible = "national,lm75";
> reg = <0x48>;
> };
>
> diff --git a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi
> index f3a3cb6ac311..8208c6a9627a 100644
> --- a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi
> +++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi
> @@ -423,14 +423,14 @@ &i2c0 {
> status = "okay";
>
> /* U26 temperature sensor placed near SoC */
> - temp1: nct75 at 4c {
> - compatible = "lm75";
> + temp1: temperature-sensor at 4c {
> + compatible = "ti,tmp75c";
> reg = <0x4c>;
> };
>
> /* U27 temperature sensor placed near RTC battery */
> - temp2: nct75 at 4d {
> - compatible = "lm75";
> + temp2: temperature-sensor at 4d {
> + compatible = "ti,tmp75c";
> reg = <0x4d>;
> };
>
> diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts
> index 1f07ba382910..886a87dfcd0d 100644
> --- a/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts
> +++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts
> @@ -531,8 +531,8 @@ i2c at 4 {
> reg = <4>;
>
> // INLET1_T
> - lm75 at 5c {
> - compatible = "ti,lm75";
> + temperature-sensor at 5c {
> + compatible = "national,lm75";
> reg = <0x5c>;
> };
> };
> @@ -543,8 +543,8 @@ i2c at 5 {
> reg = <5>;
>
> // OUTLET1_T
> - lm75 at 5c {
> - compatible = "ti,lm75";
> + temperature-sensor at 5c {
> + compatible = "national,lm75";
> reg = <0x5c>;
> };
> };
> @@ -555,8 +555,8 @@ i2c at 6 {
> reg = <6>;
>
> // OUTLET2_T
> - lm75 at 5c {
> - compatible = "ti,lm75";
> + temperature-sensor at 5c {
> + compatible = "national,lm75";
> reg = <0x5c>;
> };
> };
> @@ -567,8 +567,8 @@ i2c at 7 {
> reg = <7>;
>
> // OUTLET3_T
> - lm75 at 5c {
> - compatible = "ti,lm75";
> + temperature-sensor at 5c {
> + compatible = "national,lm75";
> reg = <0x5c>;
> };
> };
> @@ -697,8 +697,8 @@ i2c at 3 {
> reg = <3>;
>
> // M2_ZONE_T
> - lm75 at 28 {
> - compatible = "ti,lm75";
> + temperature-sensor at 28 {
> + compatible = "national,lm75";
> reg = <0x28>;
> };
> };
> @@ -709,8 +709,8 @@ i2c at 4 {
> reg = <4>;
>
> // BATT_ZONE_T
> - lm75 at 29 {
> - compatible = "ti,lm75";
> + temperature-sensor at 29 {
> + compatible = "national,lm75";
> reg = <0x29>;
> };
> };
> @@ -721,8 +721,8 @@ i2c at 5 {
> reg = <5>;
>
> // NBM1_ZONE_T
> - lm75 at 28 {
> - compatible = "ti,lm75";
> + temperature-sensor at 28 {
> + compatible = "national,lm75";
> reg = <0x28>;
> };
> };
> @@ -732,8 +732,8 @@ i2c at 6 {
> reg = <6>;
>
> // NBM2_ZONE_T
> - lm75 at 29 {
> - compatible = "ti,lm75";
> + temperature-sensor at 29 {
> + compatible = "national,lm75";
> reg = <0x29>;
> };
> };
> diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts
> index f53d45fa1de8..bcdcb30c7bf6 100644
> --- a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts
> +++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts
> @@ -198,7 +198,7 @@ &i2c0 {
> clock-frequency = <100000>;
> status = "okay";
> lm75 at 48 {
> - compatible = "lm75";
> + compatible = "national,lm75";
> reg = <0x48>;
> status = "okay";
> };
> @@ -208,8 +208,8 @@ lm75 at 48 {
> &i2c1 {
> clock-frequency = <100000>;
> status = "okay";
> - lm75 at 48 {
> - compatible = "lm75";
> + temperature-sensor at 48 {
> + compatible = "national,lm75";
> reg = <0x48>;
> status = "okay";
> };
> diff --git a/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
> index 2117de872703..0d336cbdb451 100644
> --- a/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
> +++ b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
> @@ -175,8 +175,8 @@ expander: pca9554 at 20 {
> gpio-controller;
> };
>
> - sensor2: lm75 at 49 {
> - compatible = "lm75";
> + sensor2: temperature-sensor at 49 {
> + compatible = "national,lm75b";
> reg = <0x49>;
> };
> };
> diff --git a/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
> index b2d7271d1d24..c34ee84bd716 100644
> --- a/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
> +++ b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
> @@ -254,8 +254,8 @@ pmic: mc34708 at 8 {
> interrupts = <6 4>; /* PATA_DATA6, active high */
> };
>
> - sensor1: lm75 at 48 {
> - compatible = "lm75";
> + sensor1: temperature-sensor at 48 {
> + compatible = "national,lm75b";
> reg = <0x48>;
> };
>
> diff --git a/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts b/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts
> index 224f80a4a31d..4aefbc01dfc0 100644
> --- a/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts
> +++ b/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts
> @@ -482,8 +482,8 @@ mma7455 at 1d {
> reg = <0x1d>;
> };
>
> - lm75 at 48 {
> - compatible = "nxp,lm75";
> + temperature-sensor at 48 {
> + compatible = "national,lm75b";
> reg = <0x48>;
> };
>
> diff --git a/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts b/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts
> index 1f84654df50c..846afb8ccbf1 100644
> --- a/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts
> +++ b/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts
> @@ -511,7 +511,7 @@ &i2c1 {
> clock-frequency = <400000>;
>
> sensor at 49 {
> - compatible = "lm75";
> + compatible = "national,lm75";
> reg = <0x49>;
> };
>
> diff --git a/arch/arm/boot/dts/ti/omap/am335x-nano.dts b/arch/arm/boot/dts/ti/omap/am335x-nano.dts
> index 26b5510cb3d1..56929059f5af 100644
> --- a/arch/arm/boot/dts/ti/omap/am335x-nano.dts
> +++ b/arch/arm/boot/dts/ti/omap/am335x-nano.dts
> @@ -231,7 +231,7 @@ tps: tps at 24 {
> };
>
> temperature-sensor at 48 {
> - compatible = "lm75";
> + compatible = "national,lm75";
> reg = <0x48>;
> };
>
> diff --git a/arch/arm/boot/dts/xilinx/zynq-zturn-common.dtsi b/arch/arm/boot/dts/xilinx/zynq-zturn-common.dtsi
> index dfb1fbafe3aa..33b02e05ce82 100644
> --- a/arch/arm/boot/dts/xilinx/zynq-zturn-common.dtsi
> +++ b/arch/arm/boot/dts/xilinx/zynq-zturn-common.dtsi
> @@ -97,9 +97,9 @@ &i2c0 {
> status = "okay";
> clock-frequency = <400000>;
>
> - stlm75 at 49 {
> + temperature-sensor at 49 {
> status = "okay";
> - compatible = "lm75";
> + compatible = "st,stlm75";
> reg = <0x49>;
> };
>
>
--
TQ-Systems GmbH | M?hlstra?e 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht M?nchen, HRB 105018
Gesch?ftsf?hrer: Detlef Schneider, R?diger Stahl, Stefan Schneider
http://www.tq-group.com/
prev parent reply other threads:[~2024-08-19 9:43 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-16 16:47 [PATCH v2] ARM: dts: Fix undocumented LM75 compatible nodes Rob Herring
2024-08-19 9:43 ` Alexander Stein [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4592015.LvFx2qVVIh@steina-w \
--to=alexander.stein@ew.tq-group.com \
--cc=linux-aspeed@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox