* [PATCH v3] ARM: dts: aspeed: Adding Facebook TiogaPass BMC
From: Vijay Khemka @ 2018-09-18 23:41 UTC (permalink / raw)
To: linux-aspeed
Initial introduction of Facebook TiogaPass family equipped with
Aspeed 2500 BMC SoC. TiogaPass is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Facebook.
Specifically, This adds the tiogapass platform device tree file
including the flash layout used by the tiogapass BMC machines.
This also adds an entry of tiogapass device tree file in Makefile
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/aspeed-bmc-facebook-tiogapass.dts | 146 ++++++++++++++++++
2 files changed, 147 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b5bd3de87c33..1a2db605185a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1199,6 +1199,7 @@ dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-ast2500-evb.dtb \
aspeed-bmc-arm-centriq2400-rep.dtb \
+ aspeed-bmc-facebook-tiogapass.dtb \
aspeed-bmc-intel-s2600wf.dtb \
aspeed-bmc-opp-lanyang.dtb \
aspeed-bmc-opp-palmetto.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
new file mode 100644
index 000000000000..050e72df8683
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2018 Facebook Inc.
+// Author: Vijay Khemka <vijaykhemka@fb.com>
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "Facebook TiogaPass BMC";
+ compatible = "facebook,tiogapass-bmc", "aspeed,ast2500";
+ aliases {
+ serial0 = &uart1;
+ serial4 = &uart5;
+ };
+ chosen {
+ stdout-path = &uart5;
+ bootargs = "console=ttyS4,115200 earlyprintk";
+ };
+
+ memory at 80000000 {
+ reg = <0x80000000 0x20000000>;
+ };
+};
+
+&fmc {
+ status = "okay";
+ flash at 0 {
+ status = "okay";
+ m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+ flash at 0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "pnor";
+ };
+};
+
+&uart1 {
+ // Host Console
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd1_default
+ &pinctrl_rxd1_default>;
+};
+
+&uart5 {
+ // BMC Console
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii1_default>;
+ use-ncsi;
+};
+
+&i2c0 {
+ status = "okay";
+ //Airmax Conn B, CPU0 PIROM, CPU1 PIROM
+};
+
+&i2c1 {
+ status = "okay";
+ //X24 Riser
+};
+
+&i2c2 {
+ status = "okay";
+ // Mezz Management SMBus
+};
+
+&i2c3 {
+ status = "okay";
+ // SMBus to Board ID EEPROM
+};
+
+&i2c4 {
+ status = "okay";
+ // BMC Debug Header
+};
+
+&i2c5 {
+ status = "okay";
+ //CPU Voltage regulators
+};
+
+&i2c6 {
+ status = "okay";
+ tpm at 20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
+ tmp421 at 4e {
+ compatible = "ti,tmp421";
+ reg = <0x4e>;
+ };
+ tmp421 at 4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+ eeprom at 54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ pagesize = <32>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+ //HSC, AirMax Conn A
+};
+
+&i2c8 {
+ status = "okay";
+ //Mezz Sensor SMBus
+};
+
+&i2c9 {
+ status = "okay";
+ //USB Debug Connector
+};
+
+&pwm_tacho {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
+ fan at 0 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+ };
+
+ fan at 1 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+ };
+};
--
2.17.1
^ permalink raw reply related
* [PATCH] ARM: dts: aspeed: Adding Facebook TiogaPass BMC
From: Vijay Khemka @ 2018-09-18 23:39 UTC (permalink / raw)
To: linux-aspeed
Initial introduction of Facebook TiogaPass family equipped with
Aspeed 2500 BMC SoC. TiogaPass is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Facebook.
Specifically, This adds the tiogapass platform device tree file
including the flash layout used by the tiogapass BMC machines.
This also adds an entry of tiogapass device tree file in Makefile
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/aspeed-bmc-facebook-tiogapass.dts | 146 ++++++++++++++++++
2 files changed, 147 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b5bd3de87c33..1a2db605185a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1199,6 +1199,7 @@ dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-ast2500-evb.dtb \
aspeed-bmc-arm-centriq2400-rep.dtb \
+ aspeed-bmc-facebook-tiogapass.dtb \
aspeed-bmc-intel-s2600wf.dtb \
aspeed-bmc-opp-lanyang.dtb \
aspeed-bmc-opp-palmetto.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
new file mode 100644
index 000000000000..050e72df8683
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2018 Facebook Inc.
+// Author: Vijay Khemka <vijaykhemka@fb.com>
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "Facebook TiogaPass BMC";
+ compatible = "facebook,tiogapass-bmc", "aspeed,ast2500";
+ aliases {
+ serial0 = &uart1;
+ serial4 = &uart5;
+ };
+ chosen {
+ stdout-path = &uart5;
+ bootargs = "console=ttyS4,115200 earlyprintk";
+ };
+
+ memory at 80000000 {
+ reg = <0x80000000 0x20000000>;
+ };
+};
+
+&fmc {
+ status = "okay";
+ flash at 0 {
+ status = "okay";
+ m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+ };
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
+ flash at 0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "pnor";
+ };
+};
+
+&uart1 {
+ // Host Console
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_txd1_default
+ &pinctrl_rxd1_default>;
+};
+
+&uart5 {
+ // BMC Console
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii1_default>;
+ use-ncsi;
+};
+
+&i2c0 {
+ status = "okay";
+ //Airmax Conn B, CPU0 PIROM, CPU1 PIROM
+};
+
+&i2c1 {
+ status = "okay";
+ //X24 Riser
+};
+
+&i2c2 {
+ status = "okay";
+ // Mezz Management SMBus
+};
+
+&i2c3 {
+ status = "okay";
+ // SMBus to Board ID EEPROM
+};
+
+&i2c4 {
+ status = "okay";
+ // BMC Debug Header
+};
+
+&i2c5 {
+ status = "okay";
+ //CPU Voltage regulators
+};
+
+&i2c6 {
+ status = "okay";
+ tpm at 20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
+ tmp421 at 4e {
+ compatible = "ti,tmp421";
+ reg = <0x4e>;
+ };
+ tmp421 at 4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+ eeprom at 54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ pagesize = <32>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+ //HSC, AirMax Conn A
+};
+
+&i2c8 {
+ status = "okay";
+ //Mezz Sensor SMBus
+};
+
+&i2c9 {
+ status = "okay";
+ //USB Debug Connector
+};
+
+&pwm_tacho {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default>;
+ fan at 0 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+ };
+
+ fan at 1 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+ };
+};
--
2.17.1
^ permalink raw reply related
* [PATCH v8 12/12] Add maintainers for the PECI subsystem
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds maintainer information for the PECI subsystem.
Cc: David S. Miller <davem@davemloft.net>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
MAINTAINERS | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 4ece30f15777..b9ffc217ec68 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11361,6 +11361,19 @@ L: platform-driver-x86 at vger.kernel.org
S: Maintained
F: drivers/platform/x86/peaq-wmi.c
+PECI SUBSYSTEM
+M: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
+M: Jason M Biils <jason.m.bills@linux.intel.com>
+L: openbmc at lists.ozlabs.org (moderated for non-subscribers)
+S: Maintained
+F: Documentation/devicetree/bindings/peci/
+F: drivers/mfd/intel-peci-client.c
+F: drivers/peci/
+F: drivers/hwmon/peci-*.c
+F: include/linux/mfd/intel-peci-client.h
+F: include/linux/peci.h
+F: include/uapi/linux/peci-ioctl.h
+
PER-CPU MEMORY ALLOCATOR
M: Dennis Zhou <dennis@kernel.org>
M: Tejun Heo <tj@kernel.org>
--
2.18.0
^ permalink raw reply related
* [PATCH v8 11/12] hwmon: Add PECI dimmtemp driver
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds PECI dimmtemp hwmon driver.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Stef van Os <stef.van.os@prodrive-technologies.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
---
drivers/hwmon/Kconfig | 14 ++
drivers/hwmon/Makefile | 1 +
drivers/hwmon/peci-dimmtemp.c | 286 ++++++++++++++++++++++++++++++++++
3 files changed, 301 insertions(+)
create mode 100644 drivers/hwmon/peci-dimmtemp.c
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index f08b4a670ac5..d2299d850508 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1320,6 +1320,20 @@ config SENSORS_PECI_CPUTEMP
This driver can also be built as a module. If so, the module
will be called peci-cputemp.
+config SENSORS_PECI_DIMMTEMP
+ tristate "PECI DIMM temperature monitoring support"
+ depends on PECI
+ select MFD_INTEL_PECI_CLIENT
+ help
+ If you say yes here you get support for the generic Intel PECI hwmon
+ driver which provides Digital Thermal Sensor (DTS) thermal readings of
+ DIMM components that are accessible using the PECI Client Command
+ Suite via the processor PECI client.
+ Check Documentation/hwmon/peci-dimmtemp for details.
+
+ This driver can also be built as a module. If so, the module
+ will be called peci-dimmtemp.
+
source drivers/hwmon/pmbus/Kconfig
config SENSORS_PWM_FAN
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 13ebde089ad5..b7cf35bcfbaf 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -142,6 +142,7 @@ obj-$(CONFIG_SENSORS_PC87360) += pc87360.o
obj-$(CONFIG_SENSORS_PC87427) += pc87427.o
obj-$(CONFIG_SENSORS_PCF8591) += pcf8591.o
obj-$(CONFIG_SENSORS_PECI_CPUTEMP) += peci-cputemp.o
+obj-$(CONFIG_SENSORS_PECI_DIMMTEMP) += peci-dimmtemp.o
obj-$(CONFIG_SENSORS_POWR1220) += powr1220.o
obj-$(CONFIG_SENSORS_PWM_FAN) += pwm-fan.o
obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON) += raspberrypi-hwmon.o
diff --git a/drivers/hwmon/peci-dimmtemp.c b/drivers/hwmon/peci-dimmtemp.c
new file mode 100644
index 000000000000..0b0155fa627b
--- /dev/null
+++ b/drivers/hwmon/peci-dimmtemp.c
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Intel Corporation
+
+#include <linux/hwmon.h>
+#include <linux/jiffies.h>
+#include <linux/mfd/intel-peci-client.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/workqueue.h>
+
+#define DIMM_MASK_CHECK_DELAY_JIFFIES msecs_to_jiffies(5000)
+#define DIMM_MASK_CHECK_RETRY_MAX 60 /* 60 x 5 secs = 5 minutes */
+
+struct peci_dimmtemp {
+ struct peci_mfd *mfd;
+ struct device *dev;
+ char name[PECI_NAME_SIZE];
+ u8 addr;
+ const struct cpu_gen_info *gen_info;
+ struct workqueue_struct *work_queue;
+ struct delayed_work work_handler;
+ struct temp_data temp[DIMM_NUMS_MAX];
+ u32 dimm_mask;
+ int retry_count;
+ u32 temp_config[DIMM_NUMS_MAX + 1];
+ struct hwmon_channel_info temp_info;
+ const struct hwmon_channel_info *info[2];
+ struct hwmon_chip_info chip;
+};
+
+static const char *dimmtemp_label[CHAN_RANK_MAX][DIMM_IDX_MAX] = {
+ { "DIMM A1", "DIMM A2", "DIMM A3" },
+ { "DIMM B1", "DIMM B2", "DIMM B3" },
+ { "DIMM C1", "DIMM C2", "DIMM C3" },
+ { "DIMM D1", "DIMM D2", "DIMM D3" },
+ { "DIMM E1", "DIMM E2", "DIMM E3" },
+ { "DIMM F1", "DIMM F2", "DIMM F3" },
+ { "DIMM G1", "DIMM G2", "DIMM G3" },
+ { "DIMM H1", "DIMM H2", "DIMM H3" },
+};
+
+static int get_dimm_temp(struct peci_dimmtemp *priv, int dimm_no)
+{
+ int dimm_order = dimm_no % priv->gen_info->dimm_idx_max;
+ int chan_rank = dimm_no / priv->gen_info->dimm_idx_max;
+ u8 cfg_data[4];
+ int rc;
+
+ if (!peci_temp_need_update(&priv->temp[dimm_no]))
+ return 0;
+
+ rc = peci_client_rd_pkg_cfg_cmd(priv->mfd, MBX_INDEX_DDR_DIMM_TEMP,
+ chan_rank, cfg_data);
+ if (rc)
+ return rc;
+
+ priv->temp[dimm_no].value = cfg_data[dimm_order] * 1000;
+
+ peci_temp_mark_updated(&priv->temp[dimm_no]);
+
+ return 0;
+}
+
+static int dimmtemp_read_string(struct device *dev,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel, const char **str)
+{
+ struct peci_dimmtemp *priv = dev_get_drvdata(dev);
+ u32 dimm_idx_max = priv->gen_info->dimm_idx_max;
+ int chan_rank, dimm_idx;
+
+ if (attr != hwmon_temp_label)
+ return -EOPNOTSUPP;
+
+ chan_rank = channel / dimm_idx_max;
+ dimm_idx = channel % dimm_idx_max;
+ *str = dimmtemp_label[chan_rank][dimm_idx];
+ return 0;
+}
+
+static int dimmtemp_read(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long *val)
+{
+ struct peci_dimmtemp *priv = dev_get_drvdata(dev);
+ int rc;
+
+ if (attr != hwmon_temp_input)
+ return -EOPNOTSUPP;
+
+ rc = get_dimm_temp(priv, channel);
+ if (rc)
+ return rc;
+
+ *val = priv->temp[channel].value;
+ return 0;
+}
+
+static umode_t dimmtemp_is_visible(const void *data,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ const struct peci_dimmtemp *priv = data;
+
+ if (priv->temp_config[channel] & BIT(attr) &&
+ priv->dimm_mask & BIT(channel))
+ return 0444;
+
+ return 0;
+}
+
+static const struct hwmon_ops dimmtemp_ops = {
+ .is_visible = dimmtemp_is_visible,
+ .read_string = dimmtemp_read_string,
+ .read = dimmtemp_read,
+};
+
+static int check_populated_dimms(struct peci_dimmtemp *priv)
+{
+ u32 chan_rank_max = priv->gen_info->chan_rank_max;
+ u32 dimm_idx_max = priv->gen_info->dimm_idx_max;
+ int chan_rank, dimm_idx, rc;
+ u8 cfg_data[4];
+
+ for (chan_rank = 0; chan_rank < chan_rank_max; chan_rank++) {
+ rc = peci_client_rd_pkg_cfg_cmd(priv->mfd,
+ MBX_INDEX_DDR_DIMM_TEMP,
+ chan_rank, cfg_data);
+ if (rc) {
+ priv->dimm_mask = 0;
+ return rc;
+ }
+
+ for (dimm_idx = 0; dimm_idx < dimm_idx_max; dimm_idx++)
+ if (cfg_data[dimm_idx])
+ priv->dimm_mask |= BIT(chan_rank *
+ dimm_idx_max +
+ dimm_idx);
+ }
+
+ if (!priv->dimm_mask)
+ return -EAGAIN;
+
+ dev_dbg(priv->dev, "Scanned populated DIMMs: 0x%x\n", priv->dimm_mask);
+ return 0;
+}
+
+static int create_dimm_temp_info(struct peci_dimmtemp *priv)
+{
+ int rc, i, config_idx, channels;
+ struct device *hwmon_dev;
+
+ rc = check_populated_dimms(priv);
+ if (rc) {
+ if (rc == -EAGAIN) {
+ if (priv->retry_count < DIMM_MASK_CHECK_RETRY_MAX) {
+ queue_delayed_work(priv->work_queue,
+ &priv->work_handler,
+ DIMM_MASK_CHECK_DELAY_JIFFIES);
+ priv->retry_count++;
+ dev_dbg(priv->dev,
+ "Deferred DIMM temp info creation\n");
+ } else {
+ dev_err(priv->dev,
+ "Timeout DIMM temp info creation\n");
+ rc = -ETIMEDOUT;
+ }
+ }
+
+ return rc;
+ }
+
+ channels = priv->gen_info->chan_rank_max *
+ priv->gen_info->dimm_idx_max;
+ for (i = 0, config_idx = 0; i < channels; i++)
+ if (priv->dimm_mask & BIT(i))
+ while (i >= config_idx)
+ priv->temp_config[config_idx++] =
+ HWMON_T_LABEL | HWMON_T_INPUT;
+
+ priv->chip.ops = &dimmtemp_ops;
+ priv->chip.info = priv->info;
+
+ priv->info[0] = &priv->temp_info;
+
+ priv->temp_info.type = hwmon_temp;
+ priv->temp_info.config = priv->temp_config;
+
+ hwmon_dev = devm_hwmon_device_register_with_info(priv->dev,
+ priv->name,
+ priv,
+ &priv->chip,
+ NULL);
+ rc = PTR_ERR_OR_ZERO(hwmon_dev);
+ if (!rc)
+ dev_dbg(priv->dev, "%s: sensor '%s'\n",
+ dev_name(hwmon_dev), priv->name);
+
+ return rc;
+}
+
+static void create_dimm_temp_info_delayed(struct work_struct *work)
+{
+ struct delayed_work *dwork = to_delayed_work(work);
+ struct peci_dimmtemp *priv = container_of(dwork, struct peci_dimmtemp,
+ work_handler);
+ int rc;
+
+ rc = create_dimm_temp_info(priv);
+ if (rc && rc != -EAGAIN)
+ dev_dbg(priv->dev, "Failed to create DIMM temp info\n");
+}
+
+static int peci_dimmtemp_probe(struct platform_device *pdev)
+{
+ struct peci_mfd *mfd = dev_get_drvdata(pdev->dev.parent);
+ struct device *dev = &pdev->dev;
+ struct peci_dimmtemp *priv;
+ int rc;
+
+ if ((mfd->adapter->cmd_mask &
+ (BIT(PECI_CMD_GET_TEMP) | BIT(PECI_CMD_RD_PKG_CFG))) !=
+ (BIT(PECI_CMD_GET_TEMP) | BIT(PECI_CMD_RD_PKG_CFG)))
+ return -ENODEV;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ dev_set_drvdata(dev, priv);
+ priv->mfd = mfd;
+ priv->dev = dev;
+ priv->addr = mfd->addr;
+ priv->gen_info = mfd->gen_info;
+
+ snprintf(priv->name, PECI_NAME_SIZE, "peci_dimmtemp.cpu%d",
+ priv->mfd->cpu_no);
+
+ priv->work_queue = alloc_ordered_workqueue(priv->name, 0);
+ if (!priv->work_queue)
+ return -ENOMEM;
+
+ INIT_DELAYED_WORK(&priv->work_handler, create_dimm_temp_info_delayed);
+
+ rc = create_dimm_temp_info(priv);
+ if (rc && rc != -EAGAIN) {
+ dev_err(dev, "Failed to create DIMM temp info\n");
+ goto err_free_wq;
+ }
+
+ return 0;
+
+err_free_wq:
+ destroy_workqueue(priv->work_queue);
+ return rc;
+}
+
+static int peci_dimmtemp_remove(struct platform_device *pdev)
+{
+ struct peci_dimmtemp *priv = dev_get_drvdata(&pdev->dev);
+
+ cancel_delayed_work_sync(&priv->work_handler);
+ destroy_workqueue(priv->work_queue);
+
+ return 0;
+}
+
+static const struct platform_device_id peci_dimmtemp_ids[] = {
+ { .name = "peci-dimmtemp", .driver_data = 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(platform, peci_dimmtemp_ids);
+
+static struct platform_driver peci_dimmtemp_driver = {
+ .probe = peci_dimmtemp_probe,
+ .remove = peci_dimmtemp_remove,
+ .id_table = peci_dimmtemp_ids,
+ .driver = {
+ .name = "peci-dimmtemp",
+ },
+};
+module_platform_driver(peci_dimmtemp_driver);
+
+MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>");
+MODULE_DESCRIPTION("PECI dimmtemp driver");
+MODULE_LICENSE("GPL v2");
--
2.18.0
^ permalink raw reply related
* [PATCH v8 10/12] hwmon: Add PECI cputemp driver
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds PECI cputemp hwmon driver.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Stef van Os <stef.van.os@prodrive-technologies.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
---
drivers/hwmon/Kconfig | 14 ++
drivers/hwmon/Makefile | 1 +
drivers/hwmon/peci-cputemp.c | 392 +++++++++++++++++++++++++++++++++++
3 files changed, 407 insertions(+)
create mode 100644 drivers/hwmon/peci-cputemp.c
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 81da17a42dc9..f08b4a670ac5 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1306,6 +1306,20 @@ config SENSORS_PCF8591
These devices are hard to detect and rarely found on mainstream
hardware. If unsure, say N.
+config SENSORS_PECI_CPUTEMP
+ tristate "PECI CPU temperature monitoring support"
+ depends on PECI
+ select MFD_INTEL_PECI_CLIENT
+ help
+ If you say yes here you get support for the generic Intel PECI
+ cputemp driver which provides Digital Thermal Sensor (DTS) thermal
+ readings of the CPU package and CPU cores that are accessible using
+ the PECI Client Command Suite via the processor PECI client.
+ Check Documentation/hwmon/peci-cputemp for details.
+
+ This driver can also be built as a module. If so, the module
+ will be called peci-cputemp.
+
source drivers/hwmon/pmbus/Kconfig
config SENSORS_PWM_FAN
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 93f7f41ea4ad..13ebde089ad5 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -141,6 +141,7 @@ obj-$(CONFIG_SENSORS_NTC_THERMISTOR) += ntc_thermistor.o
obj-$(CONFIG_SENSORS_PC87360) += pc87360.o
obj-$(CONFIG_SENSORS_PC87427) += pc87427.o
obj-$(CONFIG_SENSORS_PCF8591) += pcf8591.o
+obj-$(CONFIG_SENSORS_PECI_CPUTEMP) += peci-cputemp.o
obj-$(CONFIG_SENSORS_POWR1220) += powr1220.o
obj-$(CONFIG_SENSORS_PWM_FAN) += pwm-fan.o
obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON) += raspberrypi-hwmon.o
diff --git a/drivers/hwmon/peci-cputemp.c b/drivers/hwmon/peci-cputemp.c
new file mode 100644
index 000000000000..20a48200c786
--- /dev/null
+++ b/drivers/hwmon/peci-cputemp.c
@@ -0,0 +1,392 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Intel Corporation
+
+#include <linux/hwmon.h>
+#include <linux/jiffies.h>
+#include <linux/mfd/intel-peci-client.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#define DEFAULT_CHANNEL_NUMS 4
+#define CORETEMP_CHANNEL_NUMS CORE_NUMS_MAX
+#define CPUTEMP_CHANNEL_NUMS (DEFAULT_CHANNEL_NUMS + CORETEMP_CHANNEL_NUMS)
+
+/* The RESOLVED_CORES register in PCU of a client CPU */
+#define REG_RESOLVED_CORES_BUS 1
+#define REG_RESOLVED_CORES_DEVICE 30
+#define REG_RESOLVED_CORES_FUNCTION 3
+#define REG_RESOLVED_CORES_OFFSET 0xB4
+
+struct temp_group {
+ struct temp_data die;
+ struct temp_data tcontrol;
+ struct temp_data tthrottle;
+ struct temp_data tjmax;
+ struct temp_data core[CORETEMP_CHANNEL_NUMS];
+};
+
+struct peci_cputemp {
+ struct peci_mfd *mfd;
+ struct device *dev;
+ char name[PECI_NAME_SIZE];
+ u8 addr;
+ const struct cpu_gen_info *gen_info;
+ struct temp_group temp;
+ u32 core_mask;
+ u32 temp_config[CPUTEMP_CHANNEL_NUMS + 1];
+ uint config_idx;
+ struct hwmon_channel_info temp_info;
+ const struct hwmon_channel_info *info[2];
+ struct hwmon_chip_info chip;
+};
+
+enum cputemp_channels {
+ channel_die,
+ channel_tcontrol,
+ channel_tthrottle,
+ channel_tjmax,
+ channel_core,
+};
+
+static const u32 config_table[DEFAULT_CHANNEL_NUMS + 1] = {
+ /* Die temperature */
+ HWMON_T_LABEL | HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_CRIT |
+ HWMON_T_CRIT_HYST,
+
+ /* Tcontrol temperature */
+ HWMON_T_LABEL | HWMON_T_INPUT | HWMON_T_CRIT,
+
+ /* Tthrottle temperature */
+ HWMON_T_LABEL | HWMON_T_INPUT,
+
+ /* Tjmax temperature */
+ HWMON_T_LABEL | HWMON_T_INPUT,
+
+ /* Core temperature - for all core channels */
+ HWMON_T_LABEL | HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_CRIT |
+ HWMON_T_CRIT_HYST,
+};
+
+static const char *cputemp_label[CPUTEMP_CHANNEL_NUMS] = {
+ "Die",
+ "Tcontrol",
+ "Tthrottle",
+ "Tjmax",
+ "Core 0", "Core 1", "Core 2", "Core 3",
+ "Core 4", "Core 5", "Core 6", "Core 7",
+ "Core 8", "Core 9", "Core 10", "Core 11",
+ "Core 12", "Core 13", "Core 14", "Core 15",
+ "Core 16", "Core 17", "Core 18", "Core 19",
+ "Core 20", "Core 21", "Core 22", "Core 23",
+};
+
+static s32 ten_dot_six_to_millidegree(s32 val)
+{
+ return ((val ^ 0x8000) - 0x8000) * 1000 / 64;
+}
+
+static int get_temp_targets(struct peci_cputemp *priv)
+{
+ s32 tthrottle_offset;
+ s32 tcontrol_margin;
+ u8 pkg_cfg[4];
+ int rc;
+
+ /**
+ * Just use only the tcontrol marker to determine if target values need
+ * update.
+ */
+ if (!peci_temp_need_update(&priv->temp.tcontrol))
+ return 0;
+
+ rc = peci_client_rd_pkg_cfg_cmd(priv->mfd, MBX_INDEX_TEMP_TARGET,
+ 0, pkg_cfg);
+ if (rc)
+ return rc;
+
+ priv->temp.tjmax.value = pkg_cfg[2] * 1000;
+
+ tcontrol_margin = pkg_cfg[1];
+ tcontrol_margin = ((tcontrol_margin ^ 0x80) - 0x80) * 1000;
+ priv->temp.tcontrol.value = priv->temp.tjmax.value - tcontrol_margin;
+
+ tthrottle_offset = (pkg_cfg[3] & 0x2f) * 1000;
+ priv->temp.tthrottle.value = priv->temp.tjmax.value - tthrottle_offset;
+
+ peci_temp_mark_updated(&priv->temp.tcontrol);
+
+ return 0;
+}
+
+static int get_die_temp(struct peci_cputemp *priv)
+{
+ struct peci_get_temp_msg msg;
+ int rc;
+
+ if (!peci_temp_need_update(&priv->temp.die))
+ return 0;
+
+ msg.addr = priv->addr;
+
+ rc = peci_client_command(priv->mfd, PECI_CMD_GET_TEMP, &msg);
+ if (rc)
+ return rc;
+
+ /* Note that the tjmax should be available before calling it */
+ priv->temp.die.value = priv->temp.tjmax.value +
+ (msg.temp_raw * 1000 / 64);
+
+ peci_temp_mark_updated(&priv->temp.die);
+
+ return 0;
+}
+
+static int get_core_temp(struct peci_cputemp *priv, int core_index)
+{
+ s32 core_dts_margin;
+ u8 pkg_cfg[4];
+ int rc;
+
+ if (!peci_temp_need_update(&priv->temp.core[core_index]))
+ return 0;
+
+ rc = peci_client_rd_pkg_cfg_cmd(priv->mfd, MBX_INDEX_PER_CORE_DTS_TEMP,
+ core_index, pkg_cfg);
+ if (rc)
+ return rc;
+
+ core_dts_margin = le16_to_cpup((__le16 *)pkg_cfg);
+
+ /**
+ * Processors return a value of the core DTS reading in 10.6 format
+ * (10 bits signed decimal, 6 bits fractional).
+ * Error codes:
+ * 0x8000: General sensor error
+ * 0x8001: Reserved
+ * 0x8002: Underflow on reading value
+ * 0x8003-0x81ff: Reserved
+ */
+ if (core_dts_margin >= 0x8000 && core_dts_margin <= 0x81ff)
+ return -EIO;
+
+ core_dts_margin = ten_dot_six_to_millidegree(core_dts_margin);
+
+ /* Note that the tjmax should be available before calling it */
+ priv->temp.core[core_index].value = priv->temp.tjmax.value +
+ core_dts_margin;
+
+ peci_temp_mark_updated(&priv->temp.core[core_index]);
+
+ return 0;
+}
+
+static int cputemp_read_string(struct device *dev,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel, const char **str)
+{
+ if (attr != hwmon_temp_label)
+ return -EOPNOTSUPP;
+
+ *str = cputemp_label[channel];
+ return 0;
+}
+
+static int cputemp_read(struct device *dev,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel, long *val)
+{
+ struct peci_cputemp *priv = dev_get_drvdata(dev);
+ int rc, core_index;
+
+ if (channel >= CPUTEMP_CHANNEL_NUMS ||
+ !(priv->temp_config[channel] & BIT(attr)))
+ return -EOPNOTSUPP;
+
+ rc = get_temp_targets(priv);
+ if (rc)
+ return rc;
+
+ switch (attr) {
+ case hwmon_temp_input:
+ switch (channel) {
+ case channel_die:
+ rc = get_die_temp(priv);
+ if (rc)
+ break;
+
+ *val = priv->temp.die.value;
+ break;
+ case channel_tcontrol:
+ *val = priv->temp.tcontrol.value;
+ break;
+ case channel_tthrottle:
+ *val = priv->temp.tthrottle.value;
+ break;
+ case channel_tjmax:
+ *val = priv->temp.tjmax.value;
+ break;
+ default:
+ core_index = channel - DEFAULT_CHANNEL_NUMS;
+ rc = get_core_temp(priv, core_index);
+ if (rc)
+ break;
+
+ *val = priv->temp.core[core_index].value;
+ break;
+ }
+ break;
+ case hwmon_temp_max:
+ *val = priv->temp.tcontrol.value;
+ break;
+ case hwmon_temp_crit:
+ *val = priv->temp.tjmax.value;
+ break;
+ case hwmon_temp_crit_hyst:
+ *val = priv->temp.tjmax.value - priv->temp.tcontrol.value;
+ break;
+ default:
+ rc = -EOPNOTSUPP;
+ break;
+ }
+
+ return rc;
+}
+
+static umode_t cputemp_is_visible(const void *data,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ const struct peci_cputemp *priv = data;
+
+ if (priv->temp_config[channel] & BIT(attr))
+ if (channel < DEFAULT_CHANNEL_NUMS ||
+ (channel >= DEFAULT_CHANNEL_NUMS &&
+ (priv->core_mask & BIT(channel - DEFAULT_CHANNEL_NUMS))))
+ return 0444;
+
+ return 0;
+}
+
+static const struct hwmon_ops cputemp_ops = {
+ .is_visible = cputemp_is_visible,
+ .read_string = cputemp_read_string,
+ .read = cputemp_read,
+};
+
+static int check_resolved_cores(struct peci_cputemp *priv)
+{
+ struct peci_rd_pci_cfg_local_msg msg;
+ int rc;
+
+ /* Get the RESOLVED_CORES register value */
+ msg.addr = priv->addr;
+ msg.bus = REG_RESOLVED_CORES_BUS;
+ msg.device = REG_RESOLVED_CORES_DEVICE;
+ msg.function = REG_RESOLVED_CORES_FUNCTION;
+ msg.reg = REG_RESOLVED_CORES_OFFSET;
+ msg.rx_len = 4;
+
+ rc = peci_client_command(priv->mfd, PECI_CMD_RD_PCI_CFG_LOCAL, &msg);
+ if (rc)
+ return rc;
+
+ priv->core_mask = le32_to_cpup((__le32 *)msg.pci_config);
+ if (!priv->core_mask)
+ return -EAGAIN;
+
+ dev_dbg(priv->dev, "Scanned resolved cores: 0x%x\n", priv->core_mask);
+ return 0;
+}
+
+static int create_core_temp_info(struct peci_cputemp *priv)
+{
+ int rc, i;
+
+ rc = check_resolved_cores(priv);
+ if (rc)
+ return rc;
+
+ for (i = 0; i < priv->gen_info->core_max; i++)
+ if (priv->core_mask & BIT(i))
+ while (i + DEFAULT_CHANNEL_NUMS >= priv->config_idx)
+ priv->temp_config[priv->config_idx++] =
+ config_table[channel_core];
+
+ return 0;
+}
+
+static int peci_cputemp_probe(struct platform_device *pdev)
+{
+ struct peci_mfd *mfd = dev_get_drvdata(pdev->dev.parent);
+ struct device *dev = &pdev->dev;
+ struct peci_cputemp *priv;
+ struct device *hwmon_dev;
+ int rc;
+
+ if ((mfd->adapter->cmd_mask &
+ (BIT(PECI_CMD_GET_TEMP) | BIT(PECI_CMD_RD_PKG_CFG))) !=
+ (BIT(PECI_CMD_GET_TEMP) | BIT(PECI_CMD_RD_PKG_CFG)))
+ return -ENODEV;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ dev_set_drvdata(dev, priv);
+ priv->mfd = mfd;
+ priv->dev = dev;
+ priv->addr = mfd->addr;
+ priv->gen_info = mfd->gen_info;
+
+ snprintf(priv->name, PECI_NAME_SIZE, "peci_cputemp.cpu%d", mfd->cpu_no);
+
+ priv->temp_config[priv->config_idx++] = config_table[channel_die];
+ priv->temp_config[priv->config_idx++] = config_table[channel_tcontrol];
+ priv->temp_config[priv->config_idx++] = config_table[channel_tthrottle];
+ priv->temp_config[priv->config_idx++] = config_table[channel_tjmax];
+
+ rc = create_core_temp_info(priv);
+ if (rc)
+ dev_dbg(dev, "Skipped creating core temp info\n");
+
+ priv->chip.ops = &cputemp_ops;
+ priv->chip.info = priv->info;
+
+ priv->info[0] = &priv->temp_info;
+
+ priv->temp_info.type = hwmon_temp;
+ priv->temp_info.config = priv->temp_config;
+
+ hwmon_dev = devm_hwmon_device_register_with_info(priv->dev,
+ priv->name,
+ priv,
+ &priv->chip,
+ NULL);
+
+ if (IS_ERR(hwmon_dev))
+ return PTR_ERR(hwmon_dev);
+
+ dev_dbg(dev, "%s: sensor '%s'\n", dev_name(hwmon_dev), priv->name);
+
+ return 0;
+}
+
+static const struct platform_device_id peci_cputemp_ids[] = {
+ { .name = "peci-cputemp", .driver_data = 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(platform, peci_cputemp_ids);
+
+static struct platform_driver peci_cputemp_driver = {
+ .probe = peci_cputemp_probe,
+ .id_table = peci_cputemp_ids,
+ .driver = {
+ .name = "peci-cputemp",
+ },
+};
+module_platform_driver(peci_cputemp_driver);
+
+MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>");
+MODULE_DESCRIPTION("PECI cputemp driver");
+MODULE_LICENSE("GPL v2");
--
2.18.0
^ permalink raw reply related
* [PATCH v8 09/12] Documentation: hwmon: Add documents for PECI hwmon client drivers
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds hwmon documents for PECI cputemp and dimmtemp drivers.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
---
Documentation/hwmon/peci-cputemp | 78 +++++++++++++++++++++++++++++++
Documentation/hwmon/peci-dimmtemp | 50 ++++++++++++++++++++
2 files changed, 128 insertions(+)
create mode 100644 Documentation/hwmon/peci-cputemp
create mode 100644 Documentation/hwmon/peci-dimmtemp
diff --git a/Documentation/hwmon/peci-cputemp b/Documentation/hwmon/peci-cputemp
new file mode 100644
index 000000000000..821a9258f2e6
--- /dev/null
+++ b/Documentation/hwmon/peci-cputemp
@@ -0,0 +1,78 @@
+Kernel driver peci-cputemp
+==========================
+
+Supported chips:
+ One of Intel server CPUs listed below which is connected to a PECI bus.
+ * Intel Xeon E5/E7 v3 server processors
+ Intel Xeon E5-14xx v3 family
+ Intel Xeon E5-24xx v3 family
+ Intel Xeon E5-16xx v3 family
+ Intel Xeon E5-26xx v3 family
+ Intel Xeon E5-46xx v3 family
+ Intel Xeon E7-48xx v3 family
+ Intel Xeon E7-88xx v3 family
+ * Intel Xeon E5/E7 v4 server processors
+ Intel Xeon E5-16xx v4 family
+ Intel Xeon E5-26xx v4 family
+ Intel Xeon E5-46xx v4 family
+ Intel Xeon E7-48xx v4 family
+ Intel Xeon E7-88xx v4 family
+ * Intel Xeon Scalable server processors
+ Intel Xeon Bronze family
+ Intel Xeon Silver family
+ Intel Xeon Gold family
+ Intel Xeon Platinum family
+ Addresses scanned: PECI client address 0x30 - 0x37
+ Datasheet: Available from http://www.intel.com/design/literature.htm
+
+Author:
+ Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
+
+Description
+-----------
+
+This driver implements a generic PECI hwmon feature which provides Digital
+Thermal Sensor (DTS) thermal readings of the CPU package and CPU cores that are
+accessible using the PECI Client Command Suite via the processor PECI client.
+
+All temperature values are given in millidegree Celsius and will be measurable
+only when the target CPU is powered on.
+
+sysfs attributes
+----------------
+
+temp1_label "Die"
+temp1_input Provides current die temperature of the CPU package.
+temp1_max Provides thermal control temperature of the CPU package
+ which is also known as Tcontrol.
+temp1_crit Provides shutdown temperature of the CPU package which
+ is also known as the maximum processor junction
+ temperature, Tjmax or Tprochot.
+temp1_crit_hyst Provides the hysteresis value from Tcontrol to Tjmax of
+ the CPU package.
+
+temp2_label "Tcontrol"
+temp2_input Provides current Tcontrol temperature of the CPU
+ package which is also known as Fan Temperature target.
+ Indicates the relative value from thermal monitor trip
+ temperature at which fans should be engaged.
+temp2_crit Provides Tcontrol critical value of the CPU package
+ which is same to Tjmax.
+
+temp3_label "Tthrottle"
+temp3_input Provides current Tthrottle temperature of the CPU
+ package. Used for throttling temperature. If this value
+ is allowed and lower than Tjmax - the throttle will
+ occur and reported at lower than Tjmax.
+
+temp4_label "Tjmax"
+temp4_input Provides the maximum junction temperature, Tjmax of the
+ CPU package.
+
+temp[5-*]_label Provides string "Core X", where X is resolved core
+ number.
+temp[5-*]_input Provides current temperature of each core.
+temp[5-*]_max Provides thermal control temperature of the core.
+temp[5-*]_crit Provides shutdown temperature of the core.
+temp[5-*]_crit_hyst Provides the hysteresis value from Tcontrol to Tjmax of
+ the core.
diff --git a/Documentation/hwmon/peci-dimmtemp b/Documentation/hwmon/peci-dimmtemp
new file mode 100644
index 000000000000..c54f2526188c
--- /dev/null
+++ b/Documentation/hwmon/peci-dimmtemp
@@ -0,0 +1,50 @@
+Kernel driver peci-dimmtemp
+===========================
+
+Supported chips:
+ One of Intel server CPUs listed below which is connected to a PECI bus.
+ * Intel Xeon E5/E7 v3 server processors
+ Intel Xeon E5-14xx v3 family
+ Intel Xeon E5-24xx v3 family
+ Intel Xeon E5-16xx v3 family
+ Intel Xeon E5-26xx v3 family
+ Intel Xeon E5-46xx v3 family
+ Intel Xeon E7-48xx v3 family
+ Intel Xeon E7-88xx v3 family
+ * Intel Xeon E5/E7 v4 server processors
+ Intel Xeon E5-16xx v4 family
+ Intel Xeon E5-26xx v4 family
+ Intel Xeon E5-46xx v4 family
+ Intel Xeon E7-48xx v4 family
+ Intel Xeon E7-88xx v4 family
+ * Intel Xeon Scalable server processors
+ Intel Xeon Bronze family
+ Intel Xeon Silver family
+ Intel Xeon Gold family
+ Intel Xeon Platinum family
+ Addresses scanned: PECI client address 0x30 - 0x37
+ Datasheet: Available from http://www.intel.com/design/literature.htm
+
+Author:
+ Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
+
+Description
+-----------
+
+This driver implements a generic PECI hwmon feature which provides Digital
+Thermal Sensor (DTS) thermal readings of DIMM components that are accessible
+using the PECI Client Command Suite via the processor PECI client.
+
+All temperature values are given in millidegree Celsius and will be measurable
+only when the target CPU is powered on.
+
+sysfs attributes
+----------------
+
+temp[N]_label Provides string "DIMM CI", where C is DIMM channel and
+ I is DIMM index of the populated DIMM.
+temp[N]_input Provides current temperature of the populated DIMM.
+
+Note:
+ DIMM temperature attributes will appear when the client CPU's BIOS
+ completes memory training and testing.
--
2.18.0
^ permalink raw reply related
* [PATCH v8 08/12] mfd: intel-peci-client: Add PECI client MFD driver
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds PECI client MFD driver.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: James Feist <james.feist@linux.intel.com>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Vernon Mauery <vernon.mauery@linux.intel.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
drivers/mfd/Kconfig | 14 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/intel-peci-client.c | 181 ++++++++++++++++++++++++++
include/linux/mfd/intel-peci-client.h | 81 ++++++++++++
4 files changed, 277 insertions(+)
create mode 100644 drivers/mfd/intel-peci-client.c
create mode 100644 include/linux/mfd/intel-peci-client.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 11841f4b7b2b..e68ae5d820ba 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -595,6 +595,20 @@ config MFD_INTEL_MSIC
Passage) chip. This chip embeds audio, battery, GPIO, etc.
devices used in Intel Medfield platforms.
+config MFD_INTEL_PECI_CLIENT
+ bool "Intel PECI client"
+ depends on (PECI || COMPILE_TEST)
+ select MFD_CORE
+ help
+ If you say yes to this option, support will be included for the
+ multi-functional Intel PECI (Platform Environment Control Interface)
+ client. PECI is a one-wire bus interface that provides a communication
+ channel from PECI clients in Intel processors and chipset components
+ to external monitoring or control devices.
+
+ Additional drivers must be enabled in order to use the functionality
+ of the device.
+
config MFD_IPAQ_MICRO
bool "Atmel Micro ASIC (iPAQ h3100/h3600/h3700) Support"
depends on SA1100_H3100 || SA1100_H3600
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 5856a9489cbd..ed05583dc30e 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -203,6 +203,7 @@ obj-$(CONFIG_MFD_INTEL_LPSS) += intel-lpss.o
obj-$(CONFIG_MFD_INTEL_LPSS_PCI) += intel-lpss-pci.o
obj-$(CONFIG_MFD_INTEL_LPSS_ACPI) += intel-lpss-acpi.o
obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o
+obj-$(CONFIG_MFD_INTEL_PECI_CLIENT) += intel-peci-client.o
obj-$(CONFIG_MFD_PALMAS) += palmas.o
obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o
obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
diff --git a/drivers/mfd/intel-peci-client.c b/drivers/mfd/intel-peci-client.c
new file mode 100644
index 000000000000..507e4ac66dfa
--- /dev/null
+++ b/drivers/mfd/intel-peci-client.c
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Intel Corporation
+
+#include <linux/bitfield.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/intel-peci-client.h>
+#include <linux/module.h>
+#include <linux/peci.h>
+#include <linux/of_device.h>
+
+enum cpu_gens {
+ CPU_GEN_HSX = 0, /* Haswell Xeon */
+ CPU_GEN_BRX, /* Broadwell Xeon */
+ CPU_GEN_SKX, /* Skylake Xeon */
+};
+
+static struct mfd_cell peci_functions[] = {
+ {
+ .name = "peci-cputemp",
+ },
+ {
+ .name = "peci-dimmtemp",
+ },
+ /* TODO: Add additional PECI sideband functions into here */
+};
+
+static const struct cpu_gen_info cpu_gen_info_table[] = {
+ [CPU_GEN_HSX] = {
+ .family = 6, /* Family code */
+ .model = INTEL_FAM6_HASWELL_X,
+ .core_max = CORE_MAX_ON_HSX,
+ .chan_rank_max = CHAN_RANK_MAX_ON_HSX,
+ .dimm_idx_max = DIMM_IDX_MAX_ON_HSX },
+ [CPU_GEN_BRX] = {
+ .family = 6, /* Family code */
+ .model = INTEL_FAM6_BROADWELL_X,
+ .core_max = CORE_MAX_ON_BDX,
+ .chan_rank_max = CHAN_RANK_MAX_ON_BDX,
+ .dimm_idx_max = DIMM_IDX_MAX_ON_BDX },
+ [CPU_GEN_SKX] = {
+ .family = 6, /* Family code */
+ .model = INTEL_FAM6_SKYLAKE_X,
+ .core_max = CORE_MAX_ON_SKX,
+ .chan_rank_max = CHAN_RANK_MAX_ON_SKX,
+ .dimm_idx_max = DIMM_IDX_MAX_ON_SKX },
+};
+
+static int peci_client_get_cpu_gen_info(struct peci_mfd *priv)
+{
+ u32 cpu_id;
+ int i, rc;
+
+ rc = peci_get_cpu_id(priv->adapter, priv->addr, &cpu_id);
+ if (rc)
+ return rc;
+
+ for (i = 0; i < ARRAY_SIZE(cpu_gen_info_table); i++) {
+ if (FIELD_GET(CPU_ID_FAMILY_MASK, cpu_id) +
+ FIELD_GET(CPU_ID_EXT_FAMILY_MASK, cpu_id) ==
+ cpu_gen_info_table[i].family &&
+ FIELD_GET(CPU_ID_MODEL_MASK, cpu_id) ==
+ FIELD_GET(LOWER_NIBBLE_MASK,
+ cpu_gen_info_table[i].model) &&
+ FIELD_GET(CPU_ID_EXT_MODEL_MASK, cpu_id) ==
+ FIELD_GET(UPPER_NIBBLE_MASK,
+ cpu_gen_info_table[i].model)) {
+ break;
+ }
+ }
+
+ if (i >= ARRAY_SIZE(cpu_gen_info_table))
+ return -ENODEV;
+
+ priv->gen_info = &cpu_gen_info_table[i];
+
+ return 0;
+}
+
+bool peci_temp_need_update(struct temp_data *temp)
+{
+ if (temp->valid &&
+ time_before(jiffies, temp->last_updated + UPDATE_INTERVAL))
+ return false;
+
+ return true;
+}
+EXPORT_SYMBOL_GPL(peci_temp_need_update);
+
+void peci_temp_mark_updated(struct temp_data *temp)
+{
+ temp->valid = 1;
+ temp->last_updated = jiffies;
+}
+EXPORT_SYMBOL_GPL(peci_temp_mark_updated);
+
+int peci_client_command(struct peci_mfd *priv, enum peci_cmd cmd, void *vmsg)
+{
+ return peci_command(priv->adapter, cmd, vmsg);
+}
+EXPORT_SYMBOL_GPL(peci_client_command);
+
+int peci_client_rd_pkg_cfg_cmd(struct peci_mfd *priv, u8 mbx_idx,
+ u16 param, u8 *data)
+{
+ struct peci_rd_pkg_cfg_msg msg;
+ int rc;
+
+ msg.addr = priv->addr;
+ msg.index = mbx_idx;
+ msg.param = param;
+ msg.rx_len = 4;
+
+ rc = peci_command(priv->adapter, PECI_CMD_RD_PKG_CFG, &msg);
+ if (!rc)
+ memcpy(data, msg.pkg_config, 4);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(peci_client_rd_pkg_cfg_cmd);
+
+static int peci_client_probe(struct peci_client *client)
+{
+ struct device *dev = &client->dev;
+ struct peci_mfd *priv;
+ int rc;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ dev_set_drvdata(dev, priv);
+ priv->client = client;
+ priv->dev = dev;
+ priv->adapter = client->adapter;
+ priv->addr = client->addr;
+ priv->cpu_no = client->addr - PECI_BASE_ADDR;
+
+ snprintf(priv->name, PECI_NAME_SIZE, "peci_client.cpu%d", priv->cpu_no);
+
+ rc = peci_client_get_cpu_gen_info(priv);
+ if (rc)
+ return rc;
+
+ rc = devm_mfd_add_devices(priv->dev, priv->cpu_no, peci_functions,
+ ARRAY_SIZE(peci_functions), NULL, 0, NULL);
+ if (rc < 0) {
+ dev_err(priv->dev, "devm_mfd_add_devices failed: %d\n", rc);
+ return rc;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id peci_client_of_table[] = {
+ { .compatible = "intel,peci-client" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, peci_client_of_table);
+#endif
+
+static const struct peci_device_id peci_client_ids[] = {
+ { .name = "peci-client", .driver_data = 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(peci, peci_client_ids);
+
+static struct peci_driver peci_client_driver = {
+ .probe = peci_client_probe,
+ .id_table = peci_client_ids,
+ .driver = {
+ .name = "peci-client",
+ .of_match_table =
+ of_match_ptr(peci_client_of_table),
+ },
+};
+module_peci_driver(peci_client_driver);
+
+MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>");
+MODULE_DESCRIPTION("PECI client MFD driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/intel-peci-client.h b/include/linux/mfd/intel-peci-client.h
new file mode 100644
index 000000000000..7ec272cddceb
--- /dev/null
+++ b/include/linux/mfd/intel-peci-client.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2018 Intel Corporation */
+
+#ifndef __LINUX_MFD_PECI_CLIENT_H
+#define __LINUX_MFD_PECI_CLIENT_H
+
+#include <linux/peci.h>
+
+#if IS_ENABLED(CONFIG_X86)
+#include <asm/intel-family.h>
+#else
+/**
+ * Architectures other than x86 cannot include the header file so define these
+ * at here. These are needed for detecting type of client x86 CPUs behind a PECI
+ * connection.
+ */
+#define INTEL_FAM6_HASWELL_X 0x3F
+#define INTEL_FAM6_BROADWELL_X 0x4F
+#define INTEL_FAM6_SKYLAKE_X 0x55
+#endif
+
+#define LOWER_NIBBLE_MASK GENMASK(3, 0)
+#define UPPER_NIBBLE_MASK GENMASK(7, 4)
+
+#define CPU_ID_MODEL_MASK GENMASK(7, 4)
+#define CPU_ID_FAMILY_MASK GENMASK(11, 8)
+#define CPU_ID_EXT_MODEL_MASK GENMASK(19, 16)
+#define CPU_ID_EXT_FAMILY_MASK GENMASK(27, 20)
+
+#define CORE_MAX_ON_HSX 18 /* Max number of cores on Haswell */
+#define CHAN_RANK_MAX_ON_HSX 8 /* Max number of channel ranks on Haswell */
+#define DIMM_IDX_MAX_ON_HSX 3 /* Max DIMM index per channel on Haswell */
+
+#define CORE_MAX_ON_BDX 24 /* Max number of cores on Broadwell */
+#define CHAN_RANK_MAX_ON_BDX 4 /* Max number of channel ranks on Broadwell */
+#define DIMM_IDX_MAX_ON_BDX 3 /* Max DIMM index per channel on Broadwell */
+
+#define CORE_MAX_ON_SKX 28 /* Max number of cores on Skylake */
+#define CHAN_RANK_MAX_ON_SKX 6 /* Max number of channel ranks on Skylake */
+#define DIMM_IDX_MAX_ON_SKX 2 /* Max DIMM index per channel on Skylake */
+
+#define CORE_NUMS_MAX CORE_MAX_ON_SKX
+#define CHAN_RANK_MAX CHAN_RANK_MAX_ON_HSX
+#define DIMM_IDX_MAX DIMM_IDX_MAX_ON_HSX
+#define DIMM_NUMS_MAX (CHAN_RANK_MAX * DIMM_IDX_MAX)
+
+#define TEMP_TYPE_PECI 6 /* Sensor type 6: Intel PECI */
+
+#define UPDATE_INTERVAL HZ
+
+struct temp_data {
+ uint valid;
+ s32 value;
+ ulong last_updated;
+};
+
+struct cpu_gen_info {
+ u16 family;
+ u8 model;
+ uint core_max;
+ uint chan_rank_max;
+ uint dimm_idx_max;
+};
+
+struct peci_mfd {
+ struct peci_client *client;
+ struct device *dev;
+ struct peci_adapter *adapter;
+ char name[PECI_NAME_SIZE];
+ u8 addr;
+ uint cpu_no;
+ const struct cpu_gen_info *gen_info;
+};
+
+bool peci_temp_need_update(struct temp_data *temp);
+void peci_temp_mark_updated(struct temp_data *temp);
+int peci_client_command(struct peci_mfd *mfd, enum peci_cmd cmd, void *vmsg);
+int peci_client_rd_pkg_cfg_cmd(struct peci_mfd *mfd, u8 mbx_idx,
+ u16 param, u8 *data);
+
+#endif /* __LINUX_MFD_PECI_CLIENT_H */
--
2.18.0
^ permalink raw reply related
* [PATCH v8 07/12] dt-bindings: mfd: Add a document for PECI client MFD
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds a dt-bindings document for PECI client MFD.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: James Feist <james.feist@linux.intel.com>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Vernon Mauery <vernon.mauery@linux.intel.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
.../bindings/mfd/intel-peci-client.txt | 34 +++++++++++++++++++
1 file changed, 34 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/intel-peci-client.txt
diff --git a/Documentation/devicetree/bindings/mfd/intel-peci-client.txt b/Documentation/devicetree/bindings/mfd/intel-peci-client.txt
new file mode 100644
index 000000000000..cb341e363add
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/intel-peci-client.txt
@@ -0,0 +1,34 @@
+* Intel PECI client bindings
+
+PECI (Platform Environment Control Interface) is a one-wire bus interface that
+provides a communication channel from PECI clients in Intel processors and
+chipset components to external monitoring or control devices. PECI is designed
+to support the following sideband functions:
+
+- Processor and DRAM thermal management
+- Platform Manageability
+- Processor Interface Tuning and Diagnostics
+- Failure Analysis
+
+Required properties:
+- compatible : Should be "intel,peci-client".
+- reg : Should contain address of a client CPU. Address range of CPU
+ clients starts from 0x30 based on PECI specification.
+
+Example:
+ peci-bus at 0 {
+ compatible = "vendor,soc-peci";
+ reg = <0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ peci-client at 30 {
+ compatible = "intel,peci-client";
+ reg = <0x30>;
+ };
+
+ peci-client at 31 {
+ compatible = "intel,peci-client";
+ reg = <0x31>;
+ };
+ };
--
2.18.0
^ permalink raw reply related
* [PATCH v8 06/12] peci: Add a PECI adapter driver for Aspeed AST24xx/AST25xx
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds PECI adapter driver implementation for Aspeed
AST24xx/AST25xx SoCs.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
---
drivers/peci/Kconfig | 27 ++
drivers/peci/Makefile | 3 +
drivers/peci/peci-aspeed.c | 498 +++++++++++++++++++++++++++++++++++++
3 files changed, 528 insertions(+)
create mode 100644 drivers/peci/peci-aspeed.c
diff --git a/drivers/peci/Kconfig b/drivers/peci/Kconfig
index 4ccacb22a356..9e9845ebcff4 100644
--- a/drivers/peci/Kconfig
+++ b/drivers/peci/Kconfig
@@ -10,3 +10,30 @@ config PECI
The Platform Environment Control Interface (PECI) is a one-wire bus
interface that provides a communication channel from Intel processors
and chipset components to external monitoring or control devices.
+
+ If you want PECI support, you should say Y here and also to the
+ specific driver for your bus adapter(s) below.
+
+if PECI
+
+#
+# PECI hardware bus configuration
+#
+
+menu "PECI Hardware Bus support"
+
+config PECI_ASPEED
+ tristate "ASPEED PECI support"
+ select REGMAP_MMIO
+ depends on OF
+ depends on ARCH_ASPEED || COMPILE_TEST
+ help
+ Say Y here if you want support for the Platform Environment Control
+ Interface (PECI) bus adapter driver on the ASPEED SoCs.
+
+ This support is also available as a module. If so, the module
+ will be called peci-aspeed.
+
+endmenu
+
+endif # PECI
diff --git a/drivers/peci/Makefile b/drivers/peci/Makefile
index 9e8615e0d3ff..886285e69765 100644
--- a/drivers/peci/Makefile
+++ b/drivers/peci/Makefile
@@ -4,3 +4,6 @@
# Core functionality
obj-$(CONFIG_PECI) += peci-core.o
+
+# Hardware specific bus drivers
+obj-$(CONFIG_PECI_ASPEED) += peci-aspeed.o
diff --git a/drivers/peci/peci-aspeed.c b/drivers/peci/peci-aspeed.c
new file mode 100644
index 000000000000..8070ec18d484
--- /dev/null
+++ b/drivers/peci/peci-aspeed.c
@@ -0,0 +1,498 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2012-2017 ASPEED Technology Inc.
+// Copyright (c) 2018 Intel Corporation
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/peci.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* ASPEED PECI Registers */
+#define ASPEED_PECI_CTRL 0x00
+#define ASPEED_PECI_TIMING 0x04
+#define ASPEED_PECI_CMD 0x08
+#define ASPEED_PECI_CMD_CTRL 0x0c
+#define ASPEED_PECI_EXP_FCS 0x10
+#define ASPEED_PECI_CAP_FCS 0x14
+#define ASPEED_PECI_INT_CTRL 0x18
+#define ASPEED_PECI_INT_STS 0x1c
+#define ASPEED_PECI_W_DATA0 0x20
+#define ASPEED_PECI_W_DATA1 0x24
+#define ASPEED_PECI_W_DATA2 0x28
+#define ASPEED_PECI_W_DATA3 0x2c
+#define ASPEED_PECI_R_DATA0 0x30
+#define ASPEED_PECI_R_DATA1 0x34
+#define ASPEED_PECI_R_DATA2 0x38
+#define ASPEED_PECI_R_DATA3 0x3c
+#define ASPEED_PECI_W_DATA4 0x40
+#define ASPEED_PECI_W_DATA5 0x44
+#define ASPEED_PECI_W_DATA6 0x48
+#define ASPEED_PECI_W_DATA7 0x4c
+#define ASPEED_PECI_R_DATA4 0x50
+#define ASPEED_PECI_R_DATA5 0x54
+#define ASPEED_PECI_R_DATA6 0x58
+#define ASPEED_PECI_R_DATA7 0x5c
+
+/* ASPEED_PECI_CTRL - 0x00 : Control Register */
+#define PECI_CTRL_SAMPLING_MASK GENMASK(19, 16)
+#define PECI_CTRL_READ_MODE_MASK GENMASK(13, 12)
+#define PECI_CTRL_READ_MODE_COUNT BIT(12)
+#define PECI_CTRL_READ_MODE_DBG BIT(13)
+#define PECI_CTRL_CLK_SOURCE_MASK BIT(11)
+#define PECI_CTRL_CLK_DIV_MASK GENMASK(10, 8)
+#define PECI_CTRL_INVERT_OUT BIT(7)
+#define PECI_CTRL_INVERT_IN BIT(6)
+#define PECI_CTRL_BUS_CONTENT_EN BIT(5)
+#define PECI_CTRL_PECI_EN BIT(4)
+#define PECI_CTRL_PECI_CLK_EN BIT(0)
+
+/* ASPEED_PECI_TIMING - 0x04 : Timing Negotiation Register */
+#define PECI_TIMING_MESSAGE_MASK GENMASK(15, 8)
+#define PECI_TIMING_ADDRESS_MASK GENMASK(7, 0)
+
+/* ASPEED_PECI_CMD - 0x08 : Command Register */
+#define PECI_CMD_PIN_MON BIT(31)
+#define PECI_CMD_STS_MASK GENMASK(27, 24)
+#define PECI_CMD_IDLE_MASK (PECI_CMD_STS_MASK | PECI_CMD_PIN_MON)
+#define PECI_CMD_FIRE BIT(0)
+
+/* ASPEED_PECI_LEN - 0x0C : Read/Write Length Register */
+#define PECI_AW_FCS_EN BIT(31)
+#define PECI_READ_LEN_MASK GENMASK(23, 16)
+#define PECI_WRITE_LEN_MASK GENMASK(15, 8)
+#define PECI_TAGET_ADDR_MASK GENMASK(7, 0)
+
+/* ASPEED_PECI_EXP_FCS - 0x10 : Expected FCS Data Register */
+#define PECI_EXPECT_READ_FCS_MASK GENMASK(23, 16)
+#define PECI_EXPECT_AW_FCS_AUTO_MASK GENMASK(15, 8)
+#define PECI_EXPECT_WRITE_FCS_MASK GENMASK(7, 0)
+
+/* ASPEED_PECI_CAP_FCS - 0x14 : Captured FCS Data Register */
+#define PECI_CAPTURE_READ_FCS_MASK GENMASK(23, 16)
+#define PECI_CAPTURE_WRITE_FCS_MASK GENMASK(7, 0)
+
+/* ASPEED_PECI_INT_CTRL/STS - 0x18/0x1c : Interrupt Register */
+#define PECI_INT_TIMING_RESULT_MASK GENMASK(31, 30)
+#define PECI_INT_TIMEOUT BIT(4)
+#define PECI_INT_CONNECT BIT(3)
+#define PECI_INT_W_FCS_BAD BIT(2)
+#define PECI_INT_W_FCS_ABORT BIT(1)
+#define PECI_INT_CMD_DONE BIT(0)
+
+#define PECI_INT_MASK (PECI_INT_TIMEOUT | PECI_INT_CONNECT | \
+ PECI_INT_W_FCS_BAD | PECI_INT_W_FCS_ABORT | \
+ PECI_INT_CMD_DONE)
+
+#define PECI_IDLE_CHECK_TIMEOUT_USEC 50000
+#define PECI_IDLE_CHECK_INTERVAL_USEC 10000
+
+#define PECI_RD_SAMPLING_POINT_DEFAULT 8
+#define PECI_RD_SAMPLING_POINT_MAX 15
+#define PECI_CLK_DIV_DEFAULT 0
+#define PECI_CLK_DIV_MAX 7
+#define PECI_MSG_TIMING_DEFAULT 1
+#define PECI_MSG_TIMING_MAX 255
+#define PECI_ADDR_TIMING_DEFAULT 1
+#define PECI_ADDR_TIMING_MAX 255
+#define PECI_CMD_TIMEOUT_MS_DEFAULT 1000
+#define PECI_CMD_TIMEOUT_MS_MAX 60000
+
+struct aspeed_peci {
+ struct peci_adapter *adapter;
+ struct device *dev;
+ struct regmap *regmap;
+ struct reset_control *rst;
+ int irq;
+ spinlock_t lock; /* to sync completion status handling */
+ struct completion xfer_complete;
+ u32 status;
+ u32 cmd_timeout_ms;
+};
+
+static int aspeed_peci_xfer_native(struct aspeed_peci *priv,
+ struct peci_xfer_msg *msg)
+{
+ long err, timeout = msecs_to_jiffies(priv->cmd_timeout_ms);
+ u32 peci_head, peci_state, rx_data, cmd_sts;
+ unsigned long flags;
+ int i, rc;
+ uint reg;
+
+ /* Check command sts and bus idle state */
+ rc = regmap_read_poll_timeout(priv->regmap, ASPEED_PECI_CMD, cmd_sts,
+ !(cmd_sts & PECI_CMD_IDLE_MASK),
+ PECI_IDLE_CHECK_INTERVAL_USEC,
+ PECI_IDLE_CHECK_TIMEOUT_USEC);
+ if (rc)
+ return rc; /* -ETIMEDOUT */
+
+ spin_lock_irqsave(&priv->lock, flags);
+ reinit_completion(&priv->xfer_complete);
+
+ peci_head = FIELD_PREP(PECI_TAGET_ADDR_MASK, msg->addr) |
+ FIELD_PREP(PECI_WRITE_LEN_MASK, msg->tx_len) |
+ FIELD_PREP(PECI_READ_LEN_MASK, msg->rx_len);
+
+ regmap_write(priv->regmap, ASPEED_PECI_CMD_CTRL, peci_head);
+
+ for (i = 0; i < msg->tx_len; i += 4) {
+ reg = i < 16 ? ASPEED_PECI_W_DATA0 + i % 16 :
+ ASPEED_PECI_W_DATA4 + i % 16;
+ regmap_write(priv->regmap, reg,
+ le32_to_cpup((__le32 *)&msg->tx_buf[i]));
+ }
+
+ dev_dbg(priv->dev, "HEAD : 0x%08x\n", peci_head);
+ print_hex_dump_debug("TX : ", DUMP_PREFIX_NONE, 16, 1,
+ msg->tx_buf, msg->tx_len, true);
+
+ priv->status = 0;
+ regmap_write(priv->regmap, ASPEED_PECI_CMD, PECI_CMD_FIRE);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ err = wait_for_completion_interruptible_timeout(&priv->xfer_complete,
+ timeout);
+
+ spin_lock_irqsave(&priv->lock, flags);
+ dev_dbg(priv->dev, "INT_STS : 0x%08x\n", priv->status);
+ regmap_read(priv->regmap, ASPEED_PECI_CMD, &peci_state);
+ dev_dbg(priv->dev, "PECI_STATE : 0x%lx\n",
+ FIELD_GET(PECI_CMD_STS_MASK, peci_state));
+
+ regmap_write(priv->regmap, ASPEED_PECI_CMD, 0);
+
+ if (err <= 0 || priv->status != PECI_INT_CMD_DONE) {
+ if (err < 0) { /* -ERESTARTSYS */
+ rc = (int)err;
+ goto err_irqrestore;
+ } else if (err == 0) {
+ dev_dbg(priv->dev, "Timeout waiting for a response!\n");
+ rc = -ETIMEDOUT;
+ goto err_irqrestore;
+ }
+
+ dev_dbg(priv->dev, "No valid response!\n");
+ rc = -EIO;
+ goto err_irqrestore;
+ }
+
+ /**
+ * Note that rx_len and rx_buf size can be an odd number.
+ * Byte handling is more efficient.
+ */
+ for (i = 0; i < msg->rx_len; i++) {
+ u8 byte_offset = i % 4;
+
+ if (byte_offset == 0) {
+ reg = i < 16 ? ASPEED_PECI_R_DATA0 + i % 16 :
+ ASPEED_PECI_R_DATA4 + i % 16;
+ regmap_read(priv->regmap, reg, &rx_data);
+ }
+
+ msg->rx_buf[i] = (u8)(rx_data >> (byte_offset << 3));
+ }
+
+ print_hex_dump_debug("RX : ", DUMP_PREFIX_NONE, 16, 1,
+ msg->rx_buf, msg->rx_len, true);
+
+ regmap_read(priv->regmap, ASPEED_PECI_CMD, &peci_state);
+ dev_dbg(priv->dev, "PECI_STATE : 0x%lx\n",
+ FIELD_GET(PECI_CMD_STS_MASK, peci_state));
+ dev_dbg(priv->dev, "------------------------\n");
+
+err_irqrestore:
+ spin_unlock_irqrestore(&priv->lock, flags);
+ return rc;
+}
+
+static irqreturn_t aspeed_peci_irq_handler(int irq, void *arg)
+{
+ struct aspeed_peci *priv = arg;
+ u32 status_ack = 0;
+ u32 status;
+
+ spin_lock(&priv->lock);
+ regmap_read(priv->regmap, ASPEED_PECI_INT_STS, &status);
+ priv->status |= (status & PECI_INT_MASK);
+
+ /**
+ * In most cases, interrupt bits will be set one by one but also note
+ * that multiple interrupt bits could be set at the same time.
+ */
+ if (status & PECI_INT_TIMEOUT) {
+ dev_dbg(priv->dev, "PECI_INT_TIMEOUT\n");
+ status_ack |= PECI_INT_TIMEOUT;
+ }
+
+ if (status & PECI_INT_CONNECT) {
+ dev_dbg(priv->dev, "PECI_INT_CONNECT\n");
+ status_ack |= PECI_INT_CONNECT;
+ }
+
+ if (status & PECI_INT_W_FCS_BAD) {
+ dev_dbg(priv->dev, "PECI_INT_W_FCS_BAD\n");
+ status_ack |= PECI_INT_W_FCS_BAD;
+ }
+
+ if (status & PECI_INT_W_FCS_ABORT) {
+ dev_dbg(priv->dev, "PECI_INT_W_FCS_ABORT\n");
+ status_ack |= PECI_INT_W_FCS_ABORT;
+ }
+
+ /**
+ * All commands should be ended up with a PECI_INT_CMD_DONE bit set
+ * even in an error case.
+ */
+ if (status & PECI_INT_CMD_DONE) {
+ dev_dbg(priv->dev, "PECI_INT_CMD_DONE\n");
+ status_ack |= PECI_INT_CMD_DONE;
+ complete(&priv->xfer_complete);
+ }
+
+ regmap_write(priv->regmap, ASPEED_PECI_INT_STS, status_ack);
+ spin_unlock(&priv->lock);
+ return IRQ_HANDLED;
+}
+
+static int aspeed_peci_init_ctrl(struct aspeed_peci *priv)
+{
+ u32 msg_timing, addr_timing, rd_sampling_point;
+ u32 clk_freq, clk_divisor, clk_div_val = 0;
+ struct clk *clkin;
+ int ret;
+
+ clkin = devm_clk_get(priv->dev, NULL);
+ if (IS_ERR(clkin)) {
+ dev_err(priv->dev, "Failed to get clk source.\n");
+ return PTR_ERR(clkin);
+ }
+
+ ret = of_property_read_u32(priv->dev->of_node, "clock-frequency",
+ &clk_freq);
+ if (ret) {
+ dev_err(priv->dev,
+ "Could not read clock-frequency property.\n");
+ return ret;
+ }
+
+ clk_divisor = clk_get_rate(clkin) / clk_freq;
+ devm_clk_put(priv->dev, clkin);
+
+ while ((clk_divisor >> 1) && (clk_div_val < PECI_CLK_DIV_MAX))
+ clk_div_val++;
+
+ ret = of_property_read_u32(priv->dev->of_node, "msg-timing",
+ &msg_timing);
+ if (ret || msg_timing > PECI_MSG_TIMING_MAX) {
+ if (!ret)
+ dev_warn(priv->dev,
+ "Invalid msg-timing : %u, Use default : %u\n",
+ msg_timing, PECI_MSG_TIMING_DEFAULT);
+ msg_timing = PECI_MSG_TIMING_DEFAULT;
+ }
+
+ ret = of_property_read_u32(priv->dev->of_node, "addr-timing",
+ &addr_timing);
+ if (ret || addr_timing > PECI_ADDR_TIMING_MAX) {
+ if (!ret)
+ dev_warn(priv->dev,
+ "Invalid addr-timing : %u, Use default : %u\n",
+ addr_timing, PECI_ADDR_TIMING_DEFAULT);
+ addr_timing = PECI_ADDR_TIMING_DEFAULT;
+ }
+
+ ret = of_property_read_u32(priv->dev->of_node, "rd-sampling-point",
+ &rd_sampling_point);
+ if (ret || rd_sampling_point > PECI_RD_SAMPLING_POINT_MAX) {
+ if (!ret)
+ dev_warn(priv->dev,
+ "Invalid rd-sampling-point : %u. Use default : %u\n",
+ rd_sampling_point,
+ PECI_RD_SAMPLING_POINT_DEFAULT);
+ rd_sampling_point = PECI_RD_SAMPLING_POINT_DEFAULT;
+ }
+
+ ret = of_property_read_u32(priv->dev->of_node, "cmd-timeout-ms",
+ &priv->cmd_timeout_ms);
+ if (ret || priv->cmd_timeout_ms > PECI_CMD_TIMEOUT_MS_MAX ||
+ priv->cmd_timeout_ms == 0) {
+ if (!ret)
+ dev_warn(priv->dev,
+ "Invalid cmd-timeout-ms : %u. Use default : %u\n",
+ priv->cmd_timeout_ms,
+ PECI_CMD_TIMEOUT_MS_DEFAULT);
+ priv->cmd_timeout_ms = PECI_CMD_TIMEOUT_MS_DEFAULT;
+ }
+
+ regmap_write(priv->regmap, ASPEED_PECI_CTRL,
+ FIELD_PREP(PECI_CTRL_CLK_DIV_MASK, PECI_CLK_DIV_DEFAULT) |
+ PECI_CTRL_PECI_CLK_EN);
+
+ /**
+ * Timing negotiation period setting.
+ * The unit of the programmed value is 4 times of PECI clock period.
+ */
+ regmap_write(priv->regmap, ASPEED_PECI_TIMING,
+ FIELD_PREP(PECI_TIMING_MESSAGE_MASK, msg_timing) |
+ FIELD_PREP(PECI_TIMING_ADDRESS_MASK, addr_timing));
+
+ /* Clear interrupts */
+ regmap_write(priv->regmap, ASPEED_PECI_INT_STS, PECI_INT_MASK);
+
+ /* Enable interrupts */
+ regmap_write(priv->regmap, ASPEED_PECI_INT_CTRL, PECI_INT_MASK);
+
+ /* Read sampling point and clock speed setting */
+ regmap_write(priv->regmap, ASPEED_PECI_CTRL,
+ FIELD_PREP(PECI_CTRL_SAMPLING_MASK, rd_sampling_point) |
+ FIELD_PREP(PECI_CTRL_CLK_DIV_MASK, clk_div_val) |
+ PECI_CTRL_PECI_EN | PECI_CTRL_PECI_CLK_EN);
+
+ return 0;
+}
+
+static const struct regmap_config aspeed_peci_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = ASPEED_PECI_R_DATA7,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+ .fast_io = true,
+};
+
+static int aspeed_peci_xfer(struct peci_adapter *adapter,
+ struct peci_xfer_msg *msg)
+{
+ struct aspeed_peci *priv = peci_get_adapdata(adapter);
+
+ return aspeed_peci_xfer_native(priv, msg);
+}
+
+static int aspeed_peci_probe(struct platform_device *pdev)
+{
+ struct peci_adapter *adapter;
+ struct aspeed_peci *priv;
+ struct resource *res;
+ void __iomem *base;
+ u32 cmd_sts;
+ int ret;
+
+ adapter = peci_alloc_adapter(&pdev->dev, sizeof(*priv));
+ if (!adapter)
+ return -ENOMEM;
+
+ priv = peci_get_adapdata(adapter);
+ priv->adapter = adapter;
+ priv->dev = &pdev->dev;
+ dev_set_drvdata(&pdev->dev, priv);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(base)) {
+ ret = PTR_ERR(base);
+ goto err_put_adapter_dev;
+ }
+
+ priv->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+ &aspeed_peci_regmap_config);
+ if (IS_ERR(priv->regmap)) {
+ ret = PTR_ERR(priv->regmap);
+ goto err_put_adapter_dev;
+ }
+
+ /**
+ * We check that the regmap works on this very first access,
+ * but as this is an MMIO-backed regmap, subsequent regmap
+ * access is not going to fail and we skip error checks from
+ * this point.
+ */
+ ret = regmap_read(priv->regmap, ASPEED_PECI_CMD, &cmd_sts);
+ if (ret) {
+ ret = -EIO;
+ goto err_put_adapter_dev;
+ }
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (!priv->irq) {
+ ret = -ENODEV;
+ goto err_put_adapter_dev;
+ }
+
+ ret = devm_request_irq(&pdev->dev, priv->irq, aspeed_peci_irq_handler,
+ 0, "peci-aspeed-irq", priv);
+ if (ret)
+ goto err_put_adapter_dev;
+
+ init_completion(&priv->xfer_complete);
+ spin_lock_init(&priv->lock);
+
+ priv->adapter->owner = THIS_MODULE;
+ priv->adapter->dev.of_node = of_node_get(dev_of_node(priv->dev));
+ strlcpy(priv->adapter->name, pdev->name, sizeof(priv->adapter->name));
+ priv->adapter->xfer = aspeed_peci_xfer;
+
+ priv->rst = devm_reset_control_get(&pdev->dev, NULL);
+ if (IS_ERR(priv->rst)) {
+ dev_err(&pdev->dev,
+ "missing or invalid reset controller entry");
+ ret = PTR_ERR(priv->rst);
+ goto err_put_adapter_dev;
+ }
+ reset_control_deassert(priv->rst);
+
+ ret = aspeed_peci_init_ctrl(priv);
+ if (ret)
+ goto err_put_adapter_dev;
+
+ ret = peci_add_adapter(priv->adapter);
+ if (ret)
+ goto err_put_adapter_dev;
+
+ dev_info(&pdev->dev, "peci bus %d registered, irq %d\n",
+ priv->adapter->nr, priv->irq);
+
+ return 0;
+
+err_put_adapter_dev:
+ put_device(&adapter->dev);
+ return ret;
+}
+
+static int aspeed_peci_remove(struct platform_device *pdev)
+{
+ struct aspeed_peci *priv = dev_get_drvdata(&pdev->dev);
+
+ reset_control_assert(priv->rst);
+ peci_del_adapter(priv->adapter);
+ of_node_put(priv->adapter->dev.of_node);
+
+ return 0;
+}
+
+static const struct of_device_id aspeed_peci_of_table[] = {
+ { .compatible = "aspeed,ast2400-peci", },
+ { .compatible = "aspeed,ast2500-peci", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, aspeed_peci_of_table);
+
+static struct platform_driver aspeed_peci_driver = {
+ .probe = aspeed_peci_probe,
+ .remove = aspeed_peci_remove,
+ .driver = {
+ .name = "peci-aspeed",
+ .of_match_table = of_match_ptr(aspeed_peci_of_table),
+ },
+};
+module_platform_driver(aspeed_peci_driver);
+
+MODULE_AUTHOR("Ryan Chen <ryan_chen@aspeedtech.com>");
+MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>");
+MODULE_DESCRIPTION("ASPEED PECI driver");
+MODULE_LICENSE("GPL v2");
--
2.18.0
^ permalink raw reply related
* [PATCH v8 05/12] ARM: dts: aspeed: peci: Add PECI node
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds PECI bus/adapter node of AST24xx/AST25xx into
aspeed-g4 and aspeed-g5.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
---
arch/arm/boot/dts/aspeed-g4.dtsi | 26 ++++++++++++++++++++++++++
arch/arm/boot/dts/aspeed-g5.dtsi | 26 ++++++++++++++++++++++++++
2 files changed, 52 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed-g4.dtsi
index b23a983f95a5..ba31b2f0e0d8 100644
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed-g4.dtsi
@@ -29,6 +29,7 @@
serial3 = &uart4;
serial4 = &uart5;
serial5 = &vuart;
+ peci0 = &peci0;
};
cpus {
@@ -317,6 +318,13 @@
};
};
+ peci: bus at 1e78b000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x1e78b000 0x60>;
+ };
+
uart2: serial at 1e78d000 {
compatible = "ns16550a";
reg = <0x1e78d000 0x20>;
@@ -360,6 +368,24 @@
};
};
+&peci {
+ peci0: peci-bus at 0 {
+ compatible = "aspeed,ast2400-peci";
+ reg = <0x0 0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <15>;
+ clocks = <&syscon ASPEED_CLK_GATE_REFCLK>;
+ resets = <&syscon ASPEED_RESET_PECI>;
+ clock-frequency = <24000000>;
+ msg-timing = <1>;
+ addr-timing = <1>;
+ rd-sampling-point = <8>;
+ cmd-timeout-ms = <1000>;
+ status = "disabled";
+ };
+};
+
&i2c {
i2c_ic: interrupt-controller at 0 {
#interrupt-cells = <1>;
diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi
index 87fdc146ff52..c93ab96131e6 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@@ -29,6 +29,7 @@
serial3 = &uart4;
serial4 = &uart5;
serial5 = &vuart;
+ peci0 = &peci0;
};
cpus {
@@ -377,6 +378,13 @@
};
};
+ peci: bus at 1e78b000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x1e78b000 0x60>;
+ };
+
uart2: serial at 1e78d000 {
compatible = "ns16550a";
reg = <0x1e78d000 0x20>;
@@ -420,6 +428,24 @@
};
};
+&peci {
+ peci0: peci-bus at 0 {
+ compatible = "aspeed,ast2500-peci";
+ reg = <0x0 0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <15>;
+ clocks = <&syscon ASPEED_CLK_GATE_REFCLK>;
+ resets = <&syscon ASPEED_RESET_PECI>;
+ clock-frequency = <24000000>;
+ msg-timing = <1>;
+ addr-timing = <1>;
+ rd-sampling-point = <8>;
+ cmd-timeout-ms = <1000>;
+ status = "disabled";
+ };
+};
+
&i2c {
i2c_ic: interrupt-controller at 0 {
#interrupt-cells = <1>;
--
2.18.0
^ permalink raw reply related
* [PATCH v8 04/12] dt-bindings: Add a document of PECI adapter driver for ASPEED AST24xx/25xx SoCs
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds a dt-bindings document of PECI adapter driver for ASPEED
AST24xx/25xx SoCs.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Milton Miller II <miltonm@us.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/peci/peci-aspeed.txt | 55 +++++++++++++++++++
1 file changed, 55 insertions(+)
create mode 100644 Documentation/devicetree/bindings/peci/peci-aspeed.txt
diff --git a/Documentation/devicetree/bindings/peci/peci-aspeed.txt b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
new file mode 100644
index 000000000000..cdca73a3b7d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
@@ -0,0 +1,55 @@
+Device tree configuration for PECI buses on the AST24XX and AST25XX SoCs.
+
+Required properties:
+- compatible : Should be one of:
+ "aspeed,ast2400-peci"
+ "aspeed,ast2500-peci"
+- reg : Should contain PECI controller registers location and
+ length.
+- #address-cells : Should be <1> required to define a client address.
+- #size-cells : Should be <0> required to define a client address.
+- interrupts : Should contain PECI controller interrupt.
+- clocks : Should contain clock source for PECI controller. Should
+ reference the external oscillator clock in the second
+ cell.
+- resets : Should contain phandle to reset controller with the reset
+ number in the second cell.
+- clock-frequency : Should contain the operation frequency of PECI controller
+ in units of Hz.
+ 187500 ~ 24000000
+
+Optional properties:
+- msg-timing : Message timing negotiation period. This value will
+ determine the period of message timing negotiation to be
+ issued by PECI controller. The unit of the programmed
+ value is four times of PECI clock period.
+ 0 ~ 255 (default: 1)
+- addr-timing : Address timing negotiation period. This value will
+ determine the period of address timing negotiation to be
+ issued by PECI controller. The unit of the programmed
+ value is four times of PECI clock period.
+ 0 ~ 255 (default: 1)
+- rd-sampling-point : Read sampling point selection. The whole period of a bit
+ time will be divided into 16 time frames. This value will
+ determine the time frame in which the controller will
+ sample PECI signal for data read back. Usually in the
+ middle of a bit time is the best.
+ 0 ~ 15 (default: 8)
+- cmd-timeout-ms : Command timeout in units of ms.
+ 1 ~ 60000 (default: 1000)
+
+Example:
+ peci0: peci-bus at 0 {
+ compatible = "aspeed,ast2500-peci";
+ reg = <0x0 0x60>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <15>;
+ clocks = <&syscon ASPEED_CLK_GATE_REFCLK>;
+ resets = <&syscon ASPEED_RESET_PECI>;
+ clock-frequency = <24000000>;
+ msg-timing = <1>;
+ addr-timing = <1>;
+ rd-sampling-point = <8>;
+ cmd-timeout-ms = <1000>;
+ };
--
2.18.0
^ permalink raw reply related
* [PATCH v8 03/12] peci: Add support for PECI bus driver core
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds driver implementation for PECI bus core into linux
driver framework.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Gavin Schenk <g.schenk@eckelmann.de>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Cc: David Kershner <david.kershner@unisys.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Uwe Kleine-Konig <u.kleine-koenig@pengutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Julia Cartwright <juliac@eso.teric.us>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
---
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/peci/Kconfig | 12 +
drivers/peci/Makefile | 6 +
drivers/peci/peci-core.c | 1440 +++++++++++++++++++++++++++++++
include/linux/peci.h | 104 +++
include/uapi/linux/peci-ioctl.h | 265 ++++++
7 files changed, 1830 insertions(+)
create mode 100644 drivers/peci/Kconfig
create mode 100644 drivers/peci/Makefile
create mode 100644 drivers/peci/peci-core.c
create mode 100644 include/linux/peci.h
create mode 100644 include/uapi/linux/peci-ioctl.h
diff --git a/drivers/Kconfig b/drivers/Kconfig
index ab4d43923c4d..c633db2b41fb 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -219,4 +219,6 @@ source "drivers/siox/Kconfig"
source "drivers/slimbus/Kconfig"
+source "drivers/peci/Kconfig"
+
endmenu
diff --git a/drivers/Makefile b/drivers/Makefile
index 578f469f72fb..63c9b425e6e1 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -186,3 +186,4 @@ obj-$(CONFIG_MULTIPLEXER) += mux/
obj-$(CONFIG_UNISYS_VISORBUS) += visorbus/
obj-$(CONFIG_SIOX) += siox/
obj-$(CONFIG_GNSS) += gnss/
+obj-$(CONFIG_PECI) += peci/
diff --git a/drivers/peci/Kconfig b/drivers/peci/Kconfig
new file mode 100644
index 000000000000..4ccacb22a356
--- /dev/null
+++ b/drivers/peci/Kconfig
@@ -0,0 +1,12 @@
+#
+# Platform Environment Control Interface (PECI) subsystem configuration
+#
+
+config PECI
+ bool "PECI support"
+ select RT_MUTEXES
+ select CRC8
+ help
+ The Platform Environment Control Interface (PECI) is a one-wire bus
+ interface that provides a communication channel from Intel processors
+ and chipset components to external monitoring or control devices.
diff --git a/drivers/peci/Makefile b/drivers/peci/Makefile
new file mode 100644
index 000000000000..9e8615e0d3ff
--- /dev/null
+++ b/drivers/peci/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for the PECI core and bus drivers.
+#
+
+# Core functionality
+obj-$(CONFIG_PECI) += peci-core.o
diff --git a/drivers/peci/peci-core.c b/drivers/peci/peci-core.c
new file mode 100644
index 000000000000..7a99e823c14b
--- /dev/null
+++ b/drivers/peci/peci-core.c
@@ -0,0 +1,1440 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Intel Corporation
+
+#include <linux/bitfield.h>
+#include <linux/crc8.h>
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/peci.h>
+#include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+
+/* Mask for getting minor revision number from DIB */
+#define MINOR_REV_NUM_MASK GENMASK(11, 8)
+
+/* CRC8 table for Assure Write Frame Check */
+#define PECI_CRC8_POLYNOMIAL 0x07
+DECLARE_CRC8_TABLE(peci_crc8_table);
+
+static struct device_type peci_adapter_type;
+static struct device_type peci_client_type;
+
+/* Max number of peci cdev */
+#define PECI_CDEV_MAX 16
+
+static dev_t peci_devt;
+static bool is_registered;
+
+static DEFINE_MUTEX(core_lock);
+static DEFINE_IDR(peci_adapter_idr);
+
+static struct peci_adapter *peci_get_adapter(int nr)
+{
+ struct peci_adapter *adapter;
+
+ mutex_lock(&core_lock);
+ adapter = idr_find(&peci_adapter_idr, nr);
+ if (!adapter)
+ goto out_unlock;
+
+ if (try_module_get(adapter->owner))
+ get_device(&adapter->dev);
+ else
+ adapter = NULL;
+
+out_unlock:
+ mutex_unlock(&core_lock);
+ return adapter;
+}
+
+static void peci_put_adapter(struct peci_adapter *adapter)
+{
+ if (!adapter)
+ return;
+
+ put_device(&adapter->dev);
+ module_put(adapter->owner);
+}
+
+static ssize_t name_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ return sprintf(buf, "%s\n", dev->type == &peci_client_type ?
+ to_peci_client(dev)->name : to_peci_adapter(dev)->name);
+}
+static DEVICE_ATTR_RO(name);
+
+static void peci_client_dev_release(struct device *dev)
+{
+ struct peci_client *client = to_peci_client(dev);
+
+ dev_dbg(dev, "%s: %s\n", __func__, client->name);
+ peci_put_adapter(client->adapter);
+ kfree(client);
+}
+
+static struct attribute *peci_device_attrs[] = {
+ &dev_attr_name.attr,
+ NULL
+};
+ATTRIBUTE_GROUPS(peci_device);
+
+static struct device_type peci_client_type = {
+ .groups = peci_device_groups,
+ .release = peci_client_dev_release,
+};
+
+struct peci_client *peci_verify_client(struct device *dev)
+{
+ return (dev->type == &peci_client_type)
+ ? to_peci_client(dev)
+ : NULL;
+}
+EXPORT_SYMBOL_GPL(peci_verify_client);
+
+static u8 peci_aw_fcs(u8 *data, int len)
+{
+ return crc8(peci_crc8_table, data, (size_t)len, 0);
+}
+
+static int __peci_xfer(struct peci_adapter *adapter, struct peci_xfer_msg *msg,
+ bool do_retry, bool has_aw_fcs)
+{
+ ktime_t start, end;
+ s64 elapsed_ms;
+ int rc = 0;
+
+ /**
+ * For some commands, the PECI originator may need to retry a command if
+ * the processor PECI client responds with a 0x8x completion code. In
+ * each instance, the processor PECI client may have started the
+ * operation but not completed it yet. When the 'retry' bit is set, the
+ * PECI client will ignore a new request if it exactly matches a
+ * previous valid request.
+ */
+
+ if (do_retry)
+ start = ktime_get();
+
+ do {
+ rc = adapter->xfer(adapter, msg);
+
+ if (!do_retry || rc)
+ break;
+
+ if (msg->rx_buf[0] == DEV_PECI_CC_SUCCESS)
+ break;
+
+ /* Retry is needed when completion code is 0x8x */
+ if ((msg->rx_buf[0] & DEV_PECI_CC_RETRY_CHECK_MASK) !=
+ DEV_PECI_CC_NEED_RETRY) {
+ rc = -EIO;
+ break;
+ }
+
+ /* Set the retry bit to indicate a retry attempt */
+ msg->tx_buf[1] |= DEV_PECI_RETRY_BIT;
+
+ /* Recalculate the AW FCS if it has one */
+ if (has_aw_fcs)
+ msg->tx_buf[msg->tx_len - 1] = 0x80 ^
+ peci_aw_fcs((u8 *)msg,
+ 2 + msg->tx_len);
+
+ /**
+ * Retry for at least 250ms before returning an error.
+ * Retry interval guideline:
+ * No minimum < Retry Interval < No maximum
+ * (recommend 10ms)
+ */
+ end = ktime_get();
+ elapsed_ms = ktime_to_ms(ktime_sub(end, start));
+ if (elapsed_ms >= DEV_PECI_RETRY_TIME_MS) {
+ dev_dbg(&adapter->dev, "Timeout retrying xfer!\n");
+ rc = -ETIMEDOUT;
+ break;
+ }
+
+ usleep_range((DEV_PECI_RETRY_INTERVAL_USEC >> 2) + 1,
+ DEV_PECI_RETRY_INTERVAL_USEC);
+ } while (true);
+
+ if (rc)
+ dev_dbg(&adapter->dev, "xfer error, rc: %d\n", rc);
+
+ return rc;
+}
+
+static int peci_xfer(struct peci_adapter *adapter, struct peci_xfer_msg *msg)
+{
+ return __peci_xfer(adapter, msg, false, false);
+}
+
+static int peci_xfer_with_retries(struct peci_adapter *adapter,
+ struct peci_xfer_msg *msg,
+ bool has_aw_fcs)
+{
+ return __peci_xfer(adapter, msg, true, has_aw_fcs);
+}
+
+static int peci_scan_cmd_mask(struct peci_adapter *adapter)
+{
+ struct peci_xfer_msg msg;
+ int rc = 0;
+ u32 dib;
+
+ /* Update command mask just once */
+ if (adapter->cmd_mask & BIT(PECI_CMD_XFER))
+ return 0;
+
+ msg.addr = PECI_BASE_ADDR;
+ msg.tx_len = GET_DIB_WR_LEN;
+ msg.rx_len = GET_DIB_RD_LEN;
+ msg.tx_buf[0] = GET_DIB_PECI_CMD;
+
+ rc = peci_xfer(adapter, &msg);
+ if (rc)
+ return rc;
+
+ dib = le32_to_cpup((__le32 *)msg.rx_buf);
+
+ /* Check special case for Get DIB command */
+ if (dib == 0x00) {
+ dev_dbg(&adapter->dev, "DIB read as 0x00\n");
+ return -EIO;
+ }
+
+ /**
+ * Setting up the supporting commands based on minor revision number.
+ * See PECI Spec Table 3-1.
+ */
+ switch (FIELD_GET(MINOR_REV_NUM_MASK, dib)) {
+ case 6:
+ adapter->cmd_mask |= BIT(PECI_CMD_WR_IA_MSR);
+ /* fallthrough */
+ case 5:
+ adapter->cmd_mask |= BIT(PECI_CMD_WR_PCI_CFG);
+ /* fallthrough */
+ case 4:
+ adapter->cmd_mask |= BIT(PECI_CMD_RD_PCI_CFG);
+ /* fallthrough */
+ case 3:
+ adapter->cmd_mask |= BIT(PECI_CMD_RD_PCI_CFG_LOCAL);
+ adapter->cmd_mask |= BIT(PECI_CMD_WR_PCI_CFG_LOCAL);
+ /* fallthrough */
+ case 2:
+ adapter->cmd_mask |= BIT(PECI_CMD_RD_IA_MSR);
+ /* fallthrough */
+ case 1:
+ adapter->cmd_mask |= BIT(PECI_CMD_RD_PKG_CFG);
+ adapter->cmd_mask |= BIT(PECI_CMD_WR_PKG_CFG);
+ }
+
+ adapter->cmd_mask |= BIT(PECI_CMD_XFER);
+ adapter->cmd_mask |= BIT(PECI_CMD_GET_TEMP);
+ adapter->cmd_mask |= BIT(PECI_CMD_GET_DIB);
+ adapter->cmd_mask |= BIT(PECI_CMD_PING);
+
+ return rc;
+}
+
+static int peci_cmd_support(struct peci_adapter *adapter, enum peci_cmd cmd)
+{
+ if (!(adapter->cmd_mask & BIT(PECI_CMD_PING)) &&
+ peci_scan_cmd_mask(adapter) < 0) {
+ dev_dbg(&adapter->dev, "Failed to scan command mask\n");
+ return -EIO;
+ }
+
+ if (!(adapter->cmd_mask & BIT(cmd))) {
+ dev_dbg(&adapter->dev, "Command %d is not supported\n", cmd);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int peci_ioctl_xfer(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_xfer_msg *msg = vmsg;
+
+ return peci_xfer(adapter, msg);
+}
+
+static int peci_ioctl_ping(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_ping_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+
+ msg.addr = umsg->addr;
+ msg.tx_len = 0;
+ msg.rx_len = 0;
+
+ return peci_xfer(adapter, &msg);
+}
+
+static int peci_ioctl_get_dib(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_get_dib_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ int rc;
+
+ msg.addr = umsg->addr;
+ msg.tx_len = GET_DIB_WR_LEN;
+ msg.rx_len = GET_DIB_RD_LEN;
+ msg.tx_buf[0] = GET_DIB_PECI_CMD;
+
+ rc = peci_xfer(adapter, &msg);
+ if (rc)
+ return rc;
+
+ umsg->dib = le32_to_cpup((__le32 *)msg.rx_buf);
+
+ return 0;
+}
+
+static int peci_ioctl_get_temp(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_get_temp_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ int rc;
+
+ msg.addr = umsg->addr;
+ msg.tx_len = GET_TEMP_WR_LEN;
+ msg.rx_len = GET_TEMP_RD_LEN;
+ msg.tx_buf[0] = GET_TEMP_PECI_CMD;
+
+ rc = peci_xfer(adapter, &msg);
+ if (rc)
+ return rc;
+
+ umsg->temp_raw = le16_to_cpup((__le16 *)msg.rx_buf);
+
+ return 0;
+}
+
+static int peci_ioctl_rd_pkg_cfg(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_rd_pkg_cfg_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ int rc = 0;
+
+ /* Per the PECI spec, the read length must be a byte, word, or dword */
+ if (umsg->rx_len != 1 && umsg->rx_len != 2 && umsg->rx_len != 4) {
+ dev_dbg(&adapter->dev, "Invalid read length, rx_len: %d\n",
+ umsg->rx_len);
+ return -EINVAL;
+ }
+
+ msg.addr = umsg->addr;
+ msg.tx_len = RDPKGCFG_WRITE_LEN;
+ /* read lengths of 1 and 2 result in an error, so only use 4 for now */
+ msg.rx_len = RDPKGCFG_READ_LEN_BASE + umsg->rx_len;
+ msg.tx_buf[0] = RDPKGCFG_PECI_CMD;
+ msg.tx_buf[1] = 0x00; /* request byte for Host ID | Retry bit */
+ /* Host ID is 0 for PECI 3.0 */
+ msg.tx_buf[2] = umsg->index; /* RdPkgConfig index */
+ msg.tx_buf[3] = (u8)umsg->param; /* LSB - Config parameter */
+ msg.tx_buf[4] = (u8)(umsg->param >> 8); /* MSB - Config parameter */
+
+ rc = peci_xfer_with_retries(adapter, &msg, false);
+ if (!rc)
+ memcpy(umsg->pkg_config, &msg.rx_buf[1], umsg->rx_len);
+
+ return rc;
+}
+
+static int peci_ioctl_wr_pkg_cfg(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_wr_pkg_cfg_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ int rc = 0, i;
+
+ /* Per the PECI spec, the write length must be a dword */
+ if (umsg->tx_len != 4) {
+ dev_dbg(&adapter->dev, "Invalid write length, tx_len: %d\n",
+ umsg->tx_len);
+ return -EINVAL;
+ }
+
+ msg.addr = umsg->addr;
+ msg.tx_len = WRPKGCFG_WRITE_LEN_BASE + umsg->tx_len;
+ /* read lengths of 1 and 2 result in an error, so only use 4 for now */
+ msg.rx_len = WRPKGCFG_READ_LEN;
+ msg.tx_buf[0] = WRPKGCFG_PECI_CMD;
+ msg.tx_buf[1] = 0x00; /* request byte for Host ID | Retry bit */
+ /* Host ID is 0 for PECI 3.0 */
+ msg.tx_buf[2] = umsg->index; /* RdPkgConfig index */
+ msg.tx_buf[3] = (u8)umsg->param; /* LSB - Config parameter */
+ msg.tx_buf[4] = (u8)(umsg->param >> 8); /* MSB - Config parameter */
+ for (i = 0; i < umsg->tx_len; i++)
+ msg.tx_buf[5 + i] = (u8)(umsg->value >> (i << 3));
+
+ /* Add an Assure Write Frame Check Sequence byte */
+ msg.tx_buf[5 + i] = 0x80 ^
+ peci_aw_fcs((u8 *)&msg, 8 + umsg->tx_len);
+
+ rc = peci_xfer_with_retries(adapter, &msg, true);
+
+ return rc;
+}
+
+static int peci_ioctl_rd_ia_msr(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_rd_ia_msr_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ int rc = 0;
+
+ msg.addr = umsg->addr;
+ msg.tx_len = RDIAMSR_WRITE_LEN;
+ msg.rx_len = RDIAMSR_READ_LEN;
+ msg.tx_buf[0] = RDIAMSR_PECI_CMD;
+ msg.tx_buf[1] = 0x00;
+ msg.tx_buf[2] = umsg->thread_id;
+ msg.tx_buf[3] = (u8)umsg->address;
+ msg.tx_buf[4] = (u8)(umsg->address >> 8);
+
+ rc = peci_xfer_with_retries(adapter, &msg, false);
+ if (!rc)
+ memcpy(&umsg->value, &msg.rx_buf[1], sizeof(uint64_t));
+
+ return rc;
+}
+
+static int peci_ioctl_rd_pci_cfg(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_rd_pci_cfg_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ u32 address;
+ int rc = 0;
+
+ address = umsg->reg; /* [11:0] - Register */
+ address |= (u32)umsg->function << 12; /* [14:12] - Function */
+ address |= (u32)umsg->device << 15; /* [19:15] - Device */
+ address |= (u32)umsg->bus << 20; /* [27:20] - Bus */
+ /* [31:28] - Reserved */
+ msg.addr = umsg->addr;
+ msg.tx_len = RDPCICFG_WRITE_LEN;
+ msg.rx_len = RDPCICFG_READ_LEN;
+ msg.tx_buf[0] = RDPCICFG_PECI_CMD;
+ msg.tx_buf[1] = 0x00; /* request byte for Host ID | Retry bit */
+ /* Host ID is 0 for PECI 3.0 */
+ msg.tx_buf[2] = (u8)address; /* LSB - PCI Config Address */
+ msg.tx_buf[3] = (u8)(address >> 8); /* PCI Config Address */
+ msg.tx_buf[4] = (u8)(address >> 16); /* PCI Config Address */
+ msg.tx_buf[5] = (u8)(address >> 24); /* MSB - PCI Config Address */
+
+ rc = peci_xfer_with_retries(adapter, &msg, false);
+ if (!rc)
+ memcpy(umsg->pci_config, &msg.rx_buf[1], 4);
+
+ return rc;
+}
+
+static int peci_ioctl_rd_pci_cfg_local(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_rd_pci_cfg_local_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ u32 address;
+ int rc = 0;
+
+ /* Per the PECI spec, the read length must be a byte, word, or dword */
+ if (umsg->rx_len != 1 && umsg->rx_len != 2 && umsg->rx_len != 4) {
+ dev_dbg(&adapter->dev, "Invalid read length, rx_len: %d\n",
+ umsg->rx_len);
+ return -EINVAL;
+ }
+
+ address = umsg->reg; /* [11:0] - Register */
+ address |= (u32)umsg->function << 12; /* [14:12] - Function */
+ address |= (u32)umsg->device << 15; /* [19:15] - Device */
+ address |= (u32)umsg->bus << 20; /* [23:20] - Bus */
+
+ msg.addr = umsg->addr;
+ msg.tx_len = RDPCICFGLOCAL_WRITE_LEN;
+ msg.rx_len = RDPCICFGLOCAL_READ_LEN_BASE + umsg->rx_len;
+ msg.tx_buf[0] = RDPCICFGLOCAL_PECI_CMD;
+ msg.tx_buf[1] = 0x00; /* request byte for Host ID | Retry bit */
+ /* Host ID is 0 for PECI 3.0 */
+ msg.tx_buf[2] = (u8)address; /* LSB - PCI Configuration Address */
+ msg.tx_buf[3] = (u8)(address >> 8); /* PCI Configuration Address */
+ msg.tx_buf[4] = (u8)(address >> 16); /* PCI Configuration Address */
+
+ rc = peci_xfer_with_retries(adapter, &msg, false);
+ if (!rc)
+ memcpy(umsg->pci_config, &msg.rx_buf[1], umsg->rx_len);
+
+ return rc;
+}
+
+static int peci_ioctl_wr_pci_cfg_local(struct peci_adapter *adapter, void *vmsg)
+{
+ struct peci_wr_pci_cfg_local_msg *umsg = vmsg;
+ struct peci_xfer_msg msg;
+ int rc = 0, i;
+ u32 address;
+
+ /* Per the PECI spec, the write length must be a byte, word, or dword */
+ if (umsg->tx_len != 1 && umsg->tx_len != 2 && umsg->tx_len != 4) {
+ dev_dbg(&adapter->dev, "Invalid write length, tx_len: %d\n",
+ umsg->tx_len);
+ return -EINVAL;
+ }
+
+ address = umsg->reg; /* [11:0] - Register */
+ address |= (u32)umsg->function << 12; /* [14:12] - Function */
+ address |= (u32)umsg->device << 15; /* [19:15] - Device */
+ address |= (u32)umsg->bus << 20; /* [23:20] - Bus */
+
+ msg.addr = umsg->addr;
+ msg.tx_len = WRPCICFGLOCAL_WRITE_LEN_BASE + umsg->tx_len;
+ msg.rx_len = WRPCICFGLOCAL_READ_LEN;
+ msg.tx_buf[0] = WRPCICFGLOCAL_PECI_CMD;
+ msg.tx_buf[1] = 0x00; /* request byte for Host ID | Retry bit */
+ /* Host ID is 0 for PECI 3.0 */
+ msg.tx_buf[2] = (u8)address; /* LSB - PCI Configuration Address */
+ msg.tx_buf[3] = (u8)(address >> 8); /* PCI Configuration Address */
+ msg.tx_buf[4] = (u8)(address >> 16); /* PCI Configuration Address */
+ for (i = 0; i < umsg->tx_len; i++)
+ msg.tx_buf[5 + i] = (u8)(umsg->value >> (i << 3));
+
+ /* Add an Assure Write Frame Check Sequence byte */
+ msg.tx_buf[5 + i] = 0x80 ^
+ peci_aw_fcs((u8 *)&msg, 8 + umsg->tx_len);
+
+ rc = peci_xfer_with_retries(adapter, &msg, true);
+
+ return rc;
+}
+
+typedef int (*peci_ioctl_fn_type)(struct peci_adapter *, void *);
+
+static const peci_ioctl_fn_type peci_ioctl_fn[PECI_CMD_MAX] = {
+ peci_ioctl_xfer,
+ peci_ioctl_ping,
+ peci_ioctl_get_dib,
+ peci_ioctl_get_temp,
+ peci_ioctl_rd_pkg_cfg,
+ peci_ioctl_wr_pkg_cfg,
+ peci_ioctl_rd_ia_msr,
+ NULL, /* Reserved */
+ peci_ioctl_rd_pci_cfg,
+ NULL, /* Reserved */
+ peci_ioctl_rd_pci_cfg_local,
+ peci_ioctl_wr_pci_cfg_local,
+};
+
+int peci_command(struct peci_adapter *adapter, enum peci_cmd cmd, void *vmsg)
+{
+ int rc = 0;
+
+ if (cmd >= PECI_CMD_MAX || cmd < PECI_CMD_XFER)
+ return -EINVAL;
+
+ dev_dbg(&adapter->dev, "%s, cmd=0x%02x\n", __func__, cmd);
+
+ if (!peci_ioctl_fn[cmd])
+ return -EINVAL;
+
+ rt_mutex_lock(&adapter->bus_lock);
+
+ rc = peci_cmd_support(adapter, cmd);
+ if (!rc)
+ rc = peci_ioctl_fn[cmd](adapter, vmsg);
+
+ rt_mutex_unlock(&adapter->bus_lock);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(peci_command);
+
+static long peci_ioctl(struct file *file, unsigned int iocmd, unsigned long arg)
+{
+ struct peci_adapter *adapter = file->private_data;
+ void __user *argp = (void __user *)arg;
+ unsigned int msg_len;
+ enum peci_cmd cmd;
+ int rc = 0;
+ u8 *msg;
+
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+
+ dev_dbg(&adapter->dev, "ioctl, cmd=0x%x, arg=0x%lx\n", iocmd, arg);
+
+ switch (iocmd) {
+ case PECI_IOC_XFER:
+ case PECI_IOC_PING:
+ case PECI_IOC_GET_DIB:
+ case PECI_IOC_GET_TEMP:
+ case PECI_IOC_RD_PKG_CFG:
+ case PECI_IOC_WR_PKG_CFG:
+ case PECI_IOC_RD_IA_MSR:
+ case PECI_IOC_RD_PCI_CFG:
+ case PECI_IOC_RD_PCI_CFG_LOCAL:
+ case PECI_IOC_WR_PCI_CFG_LOCAL:
+ cmd = _IOC_NR(iocmd);
+ msg_len = _IOC_SIZE(iocmd);
+ break;
+
+ default:
+ dev_dbg(&adapter->dev, "Invalid ioctl cmd : 0x%x\n", iocmd);
+ return -ENOTTY;
+ }
+
+ if (!access_ok(VERIFY_WRITE, argp, msg_len))
+ return -EFAULT;
+
+ msg = memdup_user(argp, msg_len);
+ if (IS_ERR(msg))
+ return PTR_ERR(msg);
+
+ rc = peci_command(adapter, cmd, msg);
+
+ if (!rc && copy_to_user(argp, msg, msg_len))
+ rc = -EFAULT;
+
+ kfree(msg);
+ return (long)rc;
+}
+
+static int peci_open(struct inode *inode, struct file *file)
+{
+ unsigned int minor = iminor(inode);
+ struct peci_adapter *adapter;
+
+ adapter = peci_get_adapter(minor);
+ if (!adapter)
+ return -ENODEV;
+
+ file->private_data = adapter;
+
+ return 0;
+}
+
+static int peci_release(struct inode *inode, struct file *file)
+{
+ struct peci_adapter *adapter = file->private_data;
+
+ peci_put_adapter(adapter);
+ file->private_data = NULL;
+
+ return 0;
+}
+
+static const struct file_operations peci_fops = {
+ .owner = THIS_MODULE,
+ .unlocked_ioctl = peci_ioctl,
+ .open = peci_open,
+ .release = peci_release,
+};
+
+static int peci_detect(struct peci_adapter *adapter, u8 addr)
+{
+ struct peci_ping_msg msg;
+
+ msg.addr = addr;
+
+ return peci_command(adapter, PECI_CMD_PING, &msg);
+}
+
+static const struct of_device_id *
+peci_of_match_device(const struct of_device_id *matches,
+ struct peci_client *client)
+{
+#if IS_ENABLED(CONFIG_OF)
+ if (!(client && matches))
+ return NULL;
+
+ return of_match_device(matches, &client->dev);
+#else
+ return NULL;
+#endif
+}
+
+static const struct peci_device_id *
+peci_match_id(const struct peci_device_id *id, struct peci_client *client)
+{
+ if (!(id && client))
+ return NULL;
+
+ while (id->name[0]) {
+ if (!strncmp(client->name, id->name, PECI_NAME_SIZE))
+ return id;
+ id++;
+ }
+
+ return NULL;
+}
+
+static int peci_device_match(struct device *dev, struct device_driver *drv)
+{
+ struct peci_client *client = peci_verify_client(dev);
+ struct peci_driver *driver;
+
+ /* Attempt an OF style match */
+ if (peci_of_match_device(drv->of_match_table, client))
+ return 1;
+
+ driver = to_peci_driver(drv);
+
+ /* Finally an ID match */
+ if (peci_match_id(driver->id_table, client))
+ return 1;
+
+ return 0;
+}
+
+static int peci_device_probe(struct device *dev)
+{
+ struct peci_client *client = peci_verify_client(dev);
+ struct peci_driver *driver;
+ int status = -EINVAL;
+
+ if (!client)
+ return 0;
+
+ driver = to_peci_driver(dev->driver);
+
+ if (!driver->id_table &&
+ !peci_of_match_device(dev->driver->of_match_table, client))
+ return -ENODEV;
+
+ dev_dbg(dev, "%s: name:%s\n", __func__, client->name);
+
+ status = dev_pm_domain_attach(&client->dev, true);
+ if (status == -EPROBE_DEFER)
+ return status;
+
+ if (driver->probe)
+ status = driver->probe(client);
+ else
+ status = -EINVAL;
+
+ if (status)
+ goto err_detach_pm_domain;
+
+ return 0;
+
+err_detach_pm_domain:
+ dev_pm_domain_detach(&client->dev, true);
+ return status;
+}
+
+static int peci_device_remove(struct device *dev)
+{
+ struct peci_client *client = peci_verify_client(dev);
+ struct peci_driver *driver;
+ int status = 0;
+
+ if (!client || !dev->driver)
+ return 0;
+
+ driver = to_peci_driver(dev->driver);
+ if (driver->remove) {
+ dev_dbg(dev, "%s: name:%s\n", __func__, client->name);
+ status = driver->remove(client);
+ }
+
+ dev_pm_domain_detach(&client->dev, true);
+
+ return status;
+}
+
+static void peci_device_shutdown(struct device *dev)
+{
+ struct peci_client *client = peci_verify_client(dev);
+ struct peci_driver *driver;
+
+ if (!client || !dev->driver)
+ return;
+
+ dev_dbg(dev, "%s: name:%s\n", __func__, client->name);
+
+ driver = to_peci_driver(dev->driver);
+ if (driver->shutdown)
+ driver->shutdown(client);
+}
+
+static struct bus_type peci_bus_type = {
+ .name = "peci",
+ .match = peci_device_match,
+ .probe = peci_device_probe,
+ .remove = peci_device_remove,
+ .shutdown = peci_device_shutdown,
+};
+
+static int peci_check_addr_validity(u8 addr)
+{
+ if (addr < PECI_BASE_ADDR && addr > PECI_BASE_ADDR + PECI_OFFSET_MAX)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int peci_check_client_busy(struct device *dev, void *client_new_p)
+{
+ struct peci_client *client = peci_verify_client(dev);
+ struct peci_client *client_new = client_new_p;
+
+ if (client && client->addr == client_new->addr)
+ return -EBUSY;
+
+ return 0;
+}
+
+int peci_get_cpu_id(struct peci_adapter *adapter, u8 addr, u32 *cpu_id)
+{
+ struct peci_rd_pkg_cfg_msg msg;
+ int rc;
+
+ msg.addr = addr;
+ msg.index = MBX_INDEX_CPU_ID;
+ msg.param = PKG_ID_CPU_ID;
+ msg.rx_len = 4;
+
+ rc = peci_command(adapter, PECI_CMD_RD_PKG_CFG, &msg);
+ if (!rc)
+ *cpu_id = le32_to_cpup((__le32 *)msg.pkg_config);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(peci_get_cpu_id);
+
+static struct peci_client *peci_new_device(struct peci_adapter *adapter,
+ struct peci_board_info const *info)
+{
+ struct peci_client *client;
+ int rc;
+
+ /* Increase reference count for the adapter assigned */
+ if (!peci_get_adapter(adapter->nr))
+ return NULL;
+
+ client = kzalloc(sizeof(*client), GFP_KERNEL);
+ if (!client)
+ goto err_put_adapter;
+
+ client->adapter = adapter;
+ client->addr = info->addr;
+ strlcpy(client->name, info->type, sizeof(client->name));
+
+ rc = peci_check_addr_validity(client->addr);
+ if (rc) {
+ dev_err(&adapter->dev, "Invalid PECI CPU address 0x%02hx\n",
+ client->addr);
+ goto err_free_client_silent;
+ }
+
+ /* Check online status of client */
+ rc = peci_detect(adapter, client->addr);
+ if (rc)
+ goto err_free_client;
+
+ rc = device_for_each_child(&adapter->dev, client,
+ peci_check_client_busy);
+ if (rc)
+ goto err_free_client;
+
+ client->dev.parent = &client->adapter->dev;
+ client->dev.bus = &peci_bus_type;
+ client->dev.type = &peci_client_type;
+ client->dev.of_node = info->of_node;
+ dev_set_name(&client->dev, "%d-%02x", adapter->nr, client->addr);
+
+ rc = device_register(&client->dev);
+ if (rc)
+ goto err_free_client;
+
+ dev_dbg(&adapter->dev, "client [%s] registered with bus id %s\n",
+ client->name, dev_name(&client->dev));
+
+ return client;
+
+err_free_client:
+ dev_err(&adapter->dev,
+ "Failed to register peci client %s at 0x%02x (%d)\n",
+ client->name, client->addr, rc);
+err_free_client_silent:
+ kfree(client);
+err_put_adapter:
+ peci_put_adapter(adapter);
+ return NULL;
+}
+
+static void peci_unregister_device(struct peci_client *client)
+{
+ if (!client)
+ return;
+
+ if (client->dev.of_node)
+ of_node_clear_flag(client->dev.of_node, OF_POPULATED);
+
+ device_unregister(&client->dev);
+}
+
+static int peci_unregister_client(struct device *dev, void *dummy)
+{
+ struct peci_client *client = peci_verify_client(dev);
+
+ peci_unregister_device(client);
+
+ return 0;
+}
+
+static void peci_adapter_dev_release(struct device *dev)
+{
+ struct peci_adapter *adapter = to_peci_adapter(dev);
+
+ dev_dbg(dev, "%s: %s\n", __func__, adapter->name);
+ mutex_destroy(&adapter->userspace_clients_lock);
+ rt_mutex_destroy(&adapter->bus_lock);
+ kfree(adapter);
+}
+
+static ssize_t peci_sysfs_new_device(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct peci_adapter *adapter = to_peci_adapter(dev);
+ struct peci_board_info info = {};
+ struct peci_client *client;
+ char *blank, end;
+ int rc;
+
+ /* Parse device type */
+ blank = strchr(buf, ' ');
+ if (!blank) {
+ dev_err(dev, "%s: Missing parameters\n", "new_device");
+ return -EINVAL;
+ }
+ if (blank - buf > PECI_NAME_SIZE - 1) {
+ dev_err(dev, "%s: Invalid device type\n", "new_device");
+ return -EINVAL;
+ }
+ memcpy(info.type, buf, blank - buf);
+
+ /* Parse remaining parameters, reject extra parameters */
+ rc = sscanf(++blank, "%hi%c", &info.addr, &end);
+ if (rc < 1) {
+ dev_err(dev, "%s: Can't parse client address\n", "new_device");
+ return -EINVAL;
+ }
+ if (rc > 1 && end != '\n') {
+ dev_err(dev, "%s: Extra parameters\n", "new_device");
+ return -EINVAL;
+ }
+
+ client = peci_new_device(adapter, &info);
+ if (!client)
+ return -EINVAL;
+
+ /* Keep track of the added device */
+ mutex_lock(&adapter->userspace_clients_lock);
+ list_add_tail(&client->detected, &adapter->userspace_clients);
+ mutex_unlock(&adapter->userspace_clients_lock);
+ dev_info(dev, "%s: Instantiated device %s at 0x%02hx\n", "new_device",
+ info.type, info.addr);
+
+ return count;
+}
+static DEVICE_ATTR(new_device, 0200, NULL, peci_sysfs_new_device);
+
+static ssize_t peci_sysfs_delete_device(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct peci_adapter *adapter = to_peci_adapter(dev);
+ struct peci_client *client, *next;
+ struct peci_board_info info = {};
+ struct peci_driver *driver;
+ char *blank, end;
+ int rc;
+
+ /* Parse device type */
+ blank = strchr(buf, ' ');
+ if (!blank) {
+ dev_err(dev, "%s: Missing parameters\n", "delete_device");
+ return -EINVAL;
+ }
+ if (blank - buf > PECI_NAME_SIZE - 1) {
+ dev_err(dev, "%s: Invalid device type\n", "delete_device");
+ return -EINVAL;
+ }
+ memcpy(info.type, buf, blank - buf);
+
+ /* Parse remaining parameters, reject extra parameters */
+ rc = sscanf(++blank, "%hi%c", &info.addr, &end);
+ if (rc < 1) {
+ dev_err(dev, "%s: Can't parse client address\n",
+ "delete_device");
+ return -EINVAL;
+ }
+ if (rc > 1 && end != '\n') {
+ dev_err(dev, "%s: Extra parameters\n", "delete_device");
+ return -EINVAL;
+ }
+
+ /* Make sure the device was added through sysfs */
+ rc = -ENOENT;
+ mutex_lock(&adapter->userspace_clients_lock);
+ list_for_each_entry_safe(client, next, &adapter->userspace_clients,
+ detected) {
+ driver = to_peci_driver(client->dev.driver);
+
+ if (client->addr == info.addr &&
+ !strncmp(client->name, info.type, PECI_NAME_SIZE)) {
+ dev_info(dev, "%s: Deleting device %s at 0x%02hx\n",
+ "delete_device", client->name, client->addr);
+ list_del(&client->detected);
+ peci_unregister_device(client);
+ rc = count;
+ break;
+ }
+ }
+ mutex_unlock(&adapter->userspace_clients_lock);
+
+ if (rc < 0)
+ dev_err(dev, "%s: Can't find device in list\n",
+ "delete_device");
+
+ return rc;
+}
+static DEVICE_ATTR_IGNORE_LOCKDEP(delete_device, 0200, NULL,
+ peci_sysfs_delete_device);
+
+static struct attribute *peci_adapter_attrs[] = {
+ &dev_attr_name.attr,
+ &dev_attr_new_device.attr,
+ &dev_attr_delete_device.attr,
+ NULL
+};
+ATTRIBUTE_GROUPS(peci_adapter);
+
+static struct device_type peci_adapter_type = {
+ .groups = peci_adapter_groups,
+ .release = peci_adapter_dev_release,
+};
+
+struct peci_adapter *peci_verify_adapter(struct device *dev)
+{
+ return (dev->type == &peci_adapter_type)
+ ? to_peci_adapter(dev)
+ : NULL;
+}
+EXPORT_SYMBOL_GPL(peci_verify_adapter);
+
+#if IS_ENABLED(CONFIG_OF)
+static struct peci_client *peci_of_register_device(struct peci_adapter *adapter,
+ struct device_node *node)
+{
+ struct peci_board_info info = {};
+ struct peci_client *result;
+ const __be32 *addr_be;
+ int len;
+
+ dev_dbg(&adapter->dev, "register %pOF\n", node);
+
+ if (of_modalias_node(node, info.type, sizeof(info.type)) < 0) {
+ dev_err(&adapter->dev, "modalias failure on %pOF\n", node);
+ return ERR_PTR(-EINVAL);
+ }
+
+ addr_be = of_get_property(node, "reg", &len);
+ if (!addr_be || len < sizeof(*addr_be)) {
+ dev_err(&adapter->dev, "invalid reg on %pOF\n", node);
+ return ERR_PTR(-EINVAL);
+ }
+
+ info.addr = be32_to_cpup(addr_be);
+ info.of_node = of_node_get(node);
+
+ result = peci_new_device(adapter, &info);
+ if (!result)
+ result = ERR_PTR(-EINVAL);
+
+ of_node_put(node);
+ return result;
+}
+
+static void peci_of_register_devices(struct peci_adapter *adapter)
+{
+ struct device_node *bus, *node;
+ struct peci_client *client;
+
+ /* Only register child devices if the adapter has a node pointer set */
+ if (!adapter->dev.of_node)
+ return;
+
+ bus = of_get_child_by_name(adapter->dev.of_node, "peci-bus");
+ if (!bus)
+ bus = of_node_get(adapter->dev.of_node);
+
+ for_each_available_child_of_node(bus, node) {
+ if (of_node_test_and_set_flag(node, OF_POPULATED))
+ continue;
+
+ client = peci_of_register_device(adapter, node);
+ if (IS_ERR(client)) {
+ dev_warn(&adapter->dev,
+ "Failed to create PECI device for %pOF\n",
+ node);
+ of_node_clear_flag(node, OF_POPULATED);
+ }
+ }
+
+ of_node_put(bus);
+}
+#else
+static void peci_of_register_devices(struct peci_adapter *adapter) { }
+#endif /* CONFIG_OF */
+
+#if IS_ENABLED(CONFIG_OF_DYNAMIC)
+static int peci_of_match_node(struct device *dev, void *data)
+{
+ return dev->of_node == data;
+}
+
+/* must call put_device() when done with returned peci_client device */
+static struct peci_client *peci_of_find_device(struct device_node *node)
+{
+ struct peci_client *client;
+ struct device *dev;
+
+ dev = bus_find_device(&peci_bus_type, NULL, node, peci_of_match_node);
+ if (!dev)
+ return NULL;
+
+ client = peci_verify_client(dev);
+ if (!client)
+ put_device(dev);
+
+ return client;
+}
+
+/* must call put_device() when done with returned peci_adapter device */
+static struct peci_adapter *peci_of_find_adapter(struct device_node *node)
+{
+ struct peci_adapter *adapter;
+ struct device *dev;
+
+ dev = bus_find_device(&peci_bus_type, NULL, node, peci_of_match_node);
+ if (!dev)
+ return NULL;
+
+ adapter = peci_verify_adapter(dev);
+ if (!adapter)
+ put_device(dev);
+
+ return adapter;
+}
+
+static int peci_of_notify(struct notifier_block *nb,
+ unsigned long action,
+ void *arg)
+{
+ struct of_reconfig_data *rd = arg;
+ struct peci_adapter *adapter;
+ struct peci_client *client;
+
+ switch (of_reconfig_get_state_change(action, rd)) {
+ case OF_RECONFIG_CHANGE_ADD:
+ adapter = peci_of_find_adapter(rd->dn->parent);
+ if (!adapter)
+ return NOTIFY_OK; /* not for us */
+
+ if (of_node_test_and_set_flag(rd->dn, OF_POPULATED)) {
+ put_device(&adapter->dev);
+ return NOTIFY_OK;
+ }
+
+ client = peci_of_register_device(adapter, rd->dn);
+ put_device(&adapter->dev);
+
+ if (IS_ERR(client)) {
+ dev_err(&adapter->dev,
+ "failed to create client for '%pOF'\n", rd->dn);
+ of_node_clear_flag(rd->dn, OF_POPULATED);
+ return notifier_from_errno(PTR_ERR(client));
+ }
+ break;
+ case OF_RECONFIG_CHANGE_REMOVE:
+ /* already depopulated? */
+ if (!of_node_check_flag(rd->dn, OF_POPULATED))
+ return NOTIFY_OK;
+
+ /* find our device by node */
+ client = peci_of_find_device(rd->dn);
+ if (!client)
+ return NOTIFY_OK; /* no? not meant for us */
+
+ /* unregister takes one ref away */
+ peci_unregister_device(client);
+
+ /* and put the reference of the find */
+ put_device(&client->dev);
+ break;
+ }
+
+ return NOTIFY_OK;
+}
+
+static struct notifier_block peci_of_notifier = {
+ .notifier_call = peci_of_notify,
+};
+#else
+extern struct notifier_block peci_of_notifier;
+#endif /* CONFIG_OF_DYNAMIC */
+
+struct peci_adapter *peci_alloc_adapter(struct device *dev, unsigned int size)
+{
+ struct peci_adapter *adapter;
+
+ if (!dev)
+ return NULL;
+
+ adapter = kzalloc(size + sizeof(*adapter), GFP_KERNEL);
+ if (!adapter)
+ return NULL;
+
+ device_initialize(&adapter->dev);
+ adapter->dev.parent = dev;
+ adapter->dev.bus = &peci_bus_type;
+ adapter->dev.type = &peci_adapter_type;
+ peci_set_adapdata(adapter, &adapter[1]);
+
+ return adapter;
+}
+EXPORT_SYMBOL_GPL(peci_alloc_adapter);
+
+static int peci_register_adapter(struct peci_adapter *adapter)
+{
+ int rc = -EINVAL;
+
+ /* Can't register until after driver model init */
+ if (WARN_ON(!is_registered))
+ goto err_free_idr;
+
+ if (WARN(!adapter->name[0], "peci adapter has no name"))
+ goto err_free_idr;
+
+ if (WARN(!adapter->xfer, "peci adapter has no xfer function\n"))
+ goto err_free_idr;
+
+ rt_mutex_init(&adapter->bus_lock);
+ mutex_init(&adapter->userspace_clients_lock);
+ INIT_LIST_HEAD(&adapter->userspace_clients);
+
+ dev_set_name(&adapter->dev, "peci%d", adapter->nr);
+
+ /* cdev */
+ cdev_init(&adapter->cdev, &peci_fops);
+ adapter->cdev.owner = THIS_MODULE;
+ adapter->dev.devt = MKDEV(MAJOR(peci_devt), adapter->nr);
+ rc = cdev_add(&adapter->cdev, adapter->dev.devt, 1);
+ if (rc) {
+ pr_err("adapter '%s': can't add cdev (%d)\n",
+ adapter->name, rc);
+ goto err_free_idr;
+ }
+ rc = device_add(&adapter->dev);
+ if (rc) {
+ pr_err("adapter '%s': can't add device (%d)\n",
+ adapter->name, rc);
+ goto err_del_cdev;
+ }
+
+ dev_dbg(&adapter->dev, "adapter [%s] registered\n", adapter->name);
+
+ pm_runtime_no_callbacks(&adapter->dev);
+ pm_suspend_ignore_children(&adapter->dev, true);
+ pm_runtime_enable(&adapter->dev);
+
+ /* create pre-declared device nodes */
+ peci_of_register_devices(adapter);
+
+ return 0;
+
+err_del_cdev:
+ cdev_del(&adapter->cdev);
+err_free_idr:
+ mutex_lock(&core_lock);
+ idr_remove(&peci_adapter_idr, adapter->nr);
+ mutex_unlock(&core_lock);
+ return rc;
+}
+
+static int peci_add_numbered_adapter(struct peci_adapter *adapter)
+{
+ int id;
+
+ mutex_lock(&core_lock);
+ id = idr_alloc(&peci_adapter_idr, adapter,
+ adapter->nr, adapter->nr + 1, GFP_KERNEL);
+ mutex_unlock(&core_lock);
+ if (WARN(id < 0, "couldn't get idr"))
+ return id == -ENOSPC ? -EBUSY : id;
+
+ return peci_register_adapter(adapter);
+}
+
+int peci_add_adapter(struct peci_adapter *adapter)
+{
+ struct device *dev = &adapter->dev;
+ int id;
+
+ if (dev->of_node) {
+ id = of_alias_get_id(dev->of_node, "peci");
+ if (id >= 0) {
+ adapter->nr = id;
+ return peci_add_numbered_adapter(adapter);
+ }
+ }
+
+ mutex_lock(&core_lock);
+ id = idr_alloc(&peci_adapter_idr, adapter, 0, 0, GFP_KERNEL);
+ mutex_unlock(&core_lock);
+ if (WARN(id < 0, "couldn't get idr"))
+ return id;
+
+ adapter->nr = id;
+
+ return peci_register_adapter(adapter);
+}
+EXPORT_SYMBOL_GPL(peci_add_adapter);
+
+void peci_del_adapter(struct peci_adapter *adapter)
+{
+ struct peci_client *client, *next;
+ struct peci_adapter *found;
+ int nr;
+
+ /* First make sure that this adapter was ever added */
+ mutex_lock(&core_lock);
+ found = idr_find(&peci_adapter_idr, adapter->nr);
+ mutex_unlock(&core_lock);
+
+ if (found != adapter)
+ return;
+
+ /* Remove devices instantiated from sysfs */
+ mutex_lock(&adapter->userspace_clients_lock);
+ list_for_each_entry_safe(client, next, &adapter->userspace_clients,
+ detected) {
+ dev_dbg(&adapter->dev, "Removing %s at 0x%x\n", client->name,
+ client->addr);
+ list_del(&client->detected);
+ peci_unregister_device(client);
+ }
+ mutex_unlock(&adapter->userspace_clients_lock);
+
+ /**
+ * Detach any active clients. This can't fail, thus we do not
+ * check the returned value.
+ */
+ device_for_each_child(&adapter->dev, NULL, peci_unregister_client);
+
+ /* device name is gone after device_unregister */
+ dev_dbg(&adapter->dev, "adapter [%s] unregistered\n", adapter->name);
+
+ /* free cdev */
+ cdev_del(&adapter->cdev);
+
+ pm_runtime_disable(&adapter->dev);
+
+ nr = adapter->nr;
+
+ device_unregister(&adapter->dev);
+
+ /* free bus id */
+ mutex_lock(&core_lock);
+ idr_remove(&peci_adapter_idr, nr);
+ mutex_unlock(&core_lock);
+}
+EXPORT_SYMBOL_GPL(peci_del_adapter);
+
+/**
+ * A peci_driver is used with one or more peci_client (device) nodes to access
+ * peci clients, on a bus instance associated with some peci_adapter.
+ */
+int peci_register_driver(struct module *owner, struct peci_driver *driver)
+{
+ int rc;
+
+ /* Can't register until after driver model init */
+ if (WARN_ON(!is_registered))
+ return -EAGAIN;
+
+ /* add the driver to the list of peci drivers in the driver core */
+ driver->driver.owner = owner;
+ driver->driver.bus = &peci_bus_type;
+
+ /**
+ * When registration returns, the driver core
+ * will have called probe() for all matching-but-unbound devices.
+ */
+ rc = driver_register(&driver->driver);
+ if (rc)
+ return rc;
+
+ pr_debug("driver [%s] registered\n", driver->driver.name);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(peci_register_driver);
+
+void peci_del_driver(struct peci_driver *driver)
+{
+ driver_unregister(&driver->driver);
+ pr_debug("driver [%s] unregistered\n", driver->driver.name);
+}
+EXPORT_SYMBOL_GPL(peci_del_driver);
+
+static int __init peci_init(void)
+{
+ int ret;
+
+ ret = bus_register(&peci_bus_type);
+ if (ret < 0) {
+ pr_err("peci: Failed to register PECI bus type!\n");
+ return ret;
+ }
+
+ ret = alloc_chrdev_region(&peci_devt, 0, PECI_CDEV_MAX, "peci");
+ if (ret < 0) {
+ pr_err("peci: Failed to allocate chr dev region!\n");
+ bus_unregister(&peci_bus_type);
+ return ret;
+ }
+
+ crc8_populate_msb(peci_crc8_table, PECI_CRC8_POLYNOMIAL);
+
+ if (IS_ENABLED(CONFIG_OF_DYNAMIC))
+ WARN_ON(of_reconfig_notifier_register(&peci_of_notifier));
+
+ is_registered = true;
+
+ return 0;
+}
+
+static void __exit peci_exit(void)
+{
+ if (IS_ENABLED(CONFIG_OF_DYNAMIC))
+ WARN_ON(of_reconfig_notifier_unregister(&peci_of_notifier));
+
+ unregister_chrdev_region(peci_devt, PECI_CDEV_MAX);
+ bus_unregister(&peci_bus_type);
+}
+
+postcore_initcall(peci_init);
+module_exit(peci_exit);
+
+MODULE_AUTHOR("Jason M Biils <jason.m.bills@linux.intel.com>");
+MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>");
+MODULE_DESCRIPTION("PECI bus core module");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/peci.h b/include/linux/peci.h
new file mode 100644
index 000000000000..425c9cdab6dc
--- /dev/null
+++ b/include/linux/peci.h
@@ -0,0 +1,104 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2018 Intel Corporation */
+
+#ifndef __LINUX_PECI_H
+#define __LINUX_PECI_H
+
+#include <linux/cdev.h>
+#include <linux/device.h>
+#include <linux/peci-ioctl.h>
+#include <linux/rtmutex.h>
+
+#define PECI_NAME_SIZE 32
+
+struct peci_board_info {
+ char type[PECI_NAME_SIZE];
+ unsigned short addr; /* CPU client address */
+ struct device_node *of_node;
+};
+
+struct peci_adapter {
+ struct module *owner;
+ struct rt_mutex bus_lock;
+ struct device dev;
+ struct cdev cdev;
+ int nr;
+ char name[PECI_NAME_SIZE];
+ struct mutex userspace_clients_lock; /* clients list mutex */
+ struct list_head userspace_clients;
+ int (*xfer)(struct peci_adapter *adapter,
+ struct peci_xfer_msg *msg);
+ uint cmd_mask;
+};
+
+static inline struct peci_adapter *to_peci_adapter(void *d)
+{
+ return container_of(d, struct peci_adapter, dev);
+}
+
+static inline void *peci_get_adapdata(const struct peci_adapter *adapter)
+{
+ return dev_get_drvdata(&adapter->dev);
+}
+
+static inline void peci_set_adapdata(struct peci_adapter *adapter, void *data)
+{
+ dev_set_drvdata(&adapter->dev, data);
+}
+
+struct peci_client {
+ struct device dev; /* the device structure */
+ struct peci_adapter *adapter; /* the adapter we sit on */
+ u8 addr; /* CPU client address */
+ char name[PECI_NAME_SIZE];
+ struct list_head detected;
+};
+
+static inline struct peci_client *to_peci_client(void *d)
+{
+ return container_of(d, struct peci_client, dev);
+}
+
+struct peci_device_id {
+ char name[PECI_NAME_SIZE];
+ unsigned long driver_data; /* Data private to the driver */
+};
+
+struct peci_driver {
+ int (*probe)(struct peci_client *client);
+ int (*remove)(struct peci_client *client);
+ void (*shutdown)(struct peci_client *client);
+ struct device_driver driver;
+ const struct peci_device_id *id_table;
+};
+
+static inline struct peci_driver *to_peci_driver(void *d)
+{
+ return container_of(d, struct peci_driver, driver);
+}
+
+/**
+ * module_peci_driver() - Helper macro for registering a modular PECI driver
+ * @__peci_driver: peci_driver struct
+ *
+ * Helper macro for PECI drivers which do not do anything special in module
+ * init/exit. This eliminates a lot of boilerplate. Each module may only
+ * use this macro once, and calling it replaces module_init() and module_exit()
+ */
+#define module_peci_driver(__peci_driver) \
+ module_driver(__peci_driver, peci_add_driver, peci_del_driver)
+
+/* use a define to avoid include chaining to get THIS_MODULE */
+#define peci_add_driver(driver) peci_register_driver(THIS_MODULE, driver)
+
+int peci_register_driver(struct module *owner, struct peci_driver *drv);
+void peci_del_driver(struct peci_driver *driver);
+struct peci_client *peci_verify_client(struct device *dev);
+struct peci_adapter *peci_alloc_adapter(struct device *dev, unsigned int size);
+int peci_add_adapter(struct peci_adapter *adapter);
+void peci_del_adapter(struct peci_adapter *adapter);
+struct peci_adapter *peci_verify_adapter(struct device *dev);
+int peci_command(struct peci_adapter *adpater, enum peci_cmd cmd, void *vmsg);
+int peci_get_cpu_id(struct peci_adapter *adapter, u8 addr, u32 *cpu_id);
+
+#endif /* __LINUX_PECI_H */
diff --git a/include/uapi/linux/peci-ioctl.h b/include/uapi/linux/peci-ioctl.h
new file mode 100644
index 000000000000..b30d797c3b6e
--- /dev/null
+++ b/include/uapi/linux/peci-ioctl.h
@@ -0,0 +1,265 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2018 Intel Corporation */
+
+#ifndef __PECI_IOCTL_H
+#define __PECI_IOCTL_H
+
+#include <linux/ioctl.h>
+#include <linux/types.h>
+
+/* Base Address of 48d */
+#define PECI_BASE_ADDR 0x30 /* The PECI client's default address of 0x30 */
+#define PECI_OFFSET_MAX 8 /* Max numver of CPU clients */
+
+/* PCI Access */
+#define MAX_PCI_READ_LEN 24 /* Number of bytes of the PCI Space read */
+
+#define PCI_BUS0_CPU0 0x00
+#define PCI_BUS0_CPU1 0x80
+#define PCI_CPUBUSNO_BUS 0x00
+#define PCI_CPUBUSNO_DEV 0x08
+#define PCI_CPUBUSNO_FUNC 0x02
+#define PCI_CPUBUSNO 0xcc
+#define PCI_CPUBUSNO_1 0xd0
+#define PCI_CPUBUSNO_VALID 0xd4
+
+/* Package Identifier Read Parameter Value */
+#define PKG_ID_CPU_ID 0x0000 /* CPUID Info */
+#define PKG_ID_PLATFORM_ID 0x0001 /* Platform ID */
+#define PKG_ID_UNCORE_ID 0x0002 /* Uncore Device ID */
+#define PKG_ID_MAX_THREAD_ID 0x0003 /* Max Thread ID */
+#define PKG_ID_MICROCODE_REV 0x0004 /* CPU Microcode Update Revision */
+#define PKG_ID_MACHINE_CHECK_STATUS 0x0005 /* Machine Check Status */
+
+/* RdPkgConfig Index */
+#define MBX_INDEX_CPU_ID 0 /* Package Identifier Read */
+#define MBX_INDEX_VR_DEBUG 1 /* VR Debug */
+#define MBX_INDEX_PKG_TEMP_READ 2 /* Package Temperature Read */
+#define MBX_INDEX_ENERGY_COUNTER 3 /* Energy counter */
+#define MBX_INDEX_ENERGY_STATUS 4 /* DDR Energy Status */
+#define MBX_INDEX_WAKE_MODE_BIT 5 /* "Wake on PECI" Mode bit */
+#define MBX_INDEX_EPI 6 /* Efficient Performance Indication */
+#define MBX_INDEX_PKG_RAPL_PERF 8 /* Pkg RAPL Performance Status Read */
+#define MBX_INDEX_PER_CORE_DTS_TEMP 9 /* Per Core DTS Temperature Read */
+#define MBX_INDEX_DTS_MARGIN 10 /* DTS thermal margin */
+#define MBX_INDEX_SKT_PWR_THRTL_DUR 11 /* Socket Power Throttled Duration */
+#define MBX_INDEX_CFG_TDP_CONTROL 12 /* TDP Config Control */
+#define MBX_INDEX_CFG_TDP_LEVELS 13 /* TDP Config Levels */
+#define MBX_INDEX_DDR_DIMM_TEMP 14 /* DDR DIMM Temperature */
+#define MBX_INDEX_CFG_ICCMAX 15 /* Configurable ICCMAX */
+#define MBX_INDEX_TEMP_TARGET 16 /* Temperature Target Read */
+#define MBX_INDEX_CURR_CFG_LIMIT 17 /* Current Config Limit */
+#define MBX_INDEX_DIMM_TEMP_READ 20 /* Package Thermal Status Read */
+#define MBX_INDEX_DRAM_IMC_TMP_READ 22 /* DRAM IMC Temperature Read */
+#define MBX_INDEX_DDR_CH_THERM_STAT 23 /* DDR Channel Thermal Status */
+#define MBX_INDEX_PKG_POWER_LIMIT1 26 /* Package Power Limit1 */
+#define MBX_INDEX_PKG_POWER_LIMIT2 27 /* Package Power Limit2 */
+#define MBX_INDEX_TDP 28 /* Thermal design power minimum */
+#define MBX_INDEX_TDP_HIGH 29 /* Thermal design power maximum */
+#define MBX_INDEX_TDP_UNITS 30 /* Units for power/energy registers */
+#define MBX_INDEX_RUN_TIME 31 /* Accumulated Run Time */
+#define MBX_INDEX_CONSTRAINED_TIME 32 /* Thermally Constrained Time Read */
+#define MBX_INDEX_TURBO_RATIO 33 /* Turbo Activation Ratio */
+#define MBX_INDEX_DDR_RAPL_PL1 34 /* DDR RAPL PL1 */
+#define MBX_INDEX_DDR_PWR_INFO_HIGH 35 /* DRAM Power Info Read (high) */
+#define MBX_INDEX_DDR_PWR_INFO_LOW 36 /* DRAM Power Info Read (low) */
+#define MBX_INDEX_DDR_RAPL_PL2 37 /* DDR RAPL PL2 */
+#define MBX_INDEX_DDR_RAPL_STATUS 38 /* DDR RAPL Performance Status */
+#define MBX_INDEX_DDR_HOT_ABSOLUTE 43 /* DDR Hottest Dimm Absolute Temp */
+#define MBX_INDEX_DDR_HOT_RELATIVE 44 /* DDR Hottest Dimm Relative Temp */
+#define MBX_INDEX_DDR_THROTTLE_TIME 45 /* DDR Throttle Time */
+#define MBX_INDEX_DDR_THERM_STATUS 46 /* DDR Thermal Status */
+#define MBX_INDEX_TIME_AVG_TEMP 47 /* Package time-averaged temperature */
+#define MBX_INDEX_TURBO_RATIO_LIMIT 49 /* Turbo Ratio Limit Read */
+#define MBX_INDEX_HWP_AUTO_OOB 53 /* HWP Autonomous Out-of-band */
+#define MBX_INDEX_DDR_WARM_BUDGET 55 /* DDR Warm Power Budget */
+#define MBX_INDEX_DDR_HOT_BUDGET 56 /* DDR Hot Power Budget */
+#define MBX_INDEX_PKG_PSYS_PWR_LIM3 57 /* Package/Psys Power Limit3 */
+#define MBX_INDEX_PKG_PSYS_PWR_LIM1 58 /* Package/Psys Power Limit1 */
+#define MBX_INDEX_PKG_PSYS_PWR_LIM2 59 /* Package/Psys Power Limit2 */
+#define MBX_INDEX_PKG_PSYS_PWR_LIM4 60 /* Package/Psys Power Limit4 */
+#define MBX_INDEX_PERF_LIMIT_REASON 65 /* Performance Limit Reasons */
+
+/* WrPkgConfig Index */
+#define MBX_INDEX_DIMM_AMBIENT 19
+#define MBX_INDEX_DIMM_TEMP 24
+
+/* Device Specific Completion Code (CC) Definition */
+#define DEV_PECI_CC_SUCCESS 0x40
+#define DEV_PECI_CC_TIMEOUT 0x80
+#define DEV_PECI_CC_OUT_OF_RESOURCE 0x81
+#define DEV_PECI_CC_UNAVAIL_RESOURCE 0x82
+#define DEV_PECI_CC_INVALID_REQ 0x90
+
+/* Completion Code mask to check retry needs */
+#define DEV_PECI_CC_RETRY_CHECK_MASK 0xf0
+#define DEV_PECI_CC_NEED_RETRY 0x80
+
+/* Skylake EDS says to retry for 250ms */
+#define DEV_PECI_RETRY_TIME_MS 250
+#define DEV_PECI_RETRY_INTERVAL_USEC 10000
+#define DEV_PECI_RETRY_BIT 0x01
+
+#define GET_TEMP_WR_LEN 1
+#define GET_TEMP_RD_LEN 2
+#define GET_TEMP_PECI_CMD 0x01
+
+#define GET_DIB_WR_LEN 1
+#define GET_DIB_RD_LEN 8
+#define GET_DIB_PECI_CMD 0xf7
+
+#define RDPKGCFG_WRITE_LEN 5
+#define RDPKGCFG_READ_LEN_BASE 1
+#define RDPKGCFG_PECI_CMD 0xa1
+
+#define WRPKGCFG_WRITE_LEN_BASE 6
+#define WRPKGCFG_READ_LEN 1
+#define WRPKGCFG_PECI_CMD 0xa5
+
+#define RDIAMSR_WRITE_LEN 5
+#define RDIAMSR_READ_LEN 9
+#define RDIAMSR_PECI_CMD 0xb1
+
+#define WRIAMSR_PECI_CMD 0xb5
+
+#define RDPCICFG_WRITE_LEN 6
+#define RDPCICFG_READ_LEN 5
+#define RDPCICFG_PECI_CMD 0x61
+
+#define WRPCICFG_PECI_CMD 0x65
+
+#define RDPCICFGLOCAL_WRITE_LEN 5
+#define RDPCICFGLOCAL_READ_LEN_BASE 1
+#define RDPCICFGLOCAL_PECI_CMD 0xe1
+
+#define WRPCICFGLOCAL_WRITE_LEN_BASE 6
+#define WRPCICFGLOCAL_READ_LEN 1
+#define WRPCICFGLOCAL_PECI_CMD 0xe5
+
+#define PECI_BUFFER_SIZE 32
+
+enum peci_cmd {
+ PECI_CMD_XFER = 0,
+ PECI_CMD_PING,
+ PECI_CMD_GET_DIB,
+ PECI_CMD_GET_TEMP,
+ PECI_CMD_RD_PKG_CFG,
+ PECI_CMD_WR_PKG_CFG,
+ PECI_CMD_RD_IA_MSR,
+ PECI_CMD_WR_IA_MSR,
+ PECI_CMD_RD_PCI_CFG,
+ PECI_CMD_WR_PCI_CFG,
+ PECI_CMD_RD_PCI_CFG_LOCAL,
+ PECI_CMD_WR_PCI_CFG_LOCAL,
+ PECI_CMD_MAX
+};
+
+struct peci_xfer_msg {
+ __u8 addr;
+ __u8 tx_len;
+ __u8 rx_len;
+ __u8 tx_buf[PECI_BUFFER_SIZE];
+ __u8 rx_buf[PECI_BUFFER_SIZE];
+} __attribute__((__packed__));
+
+struct peci_ping_msg {
+ __u8 addr;
+} __attribute__((__packed__));
+
+struct peci_get_dib_msg {
+ __u8 addr;
+ __u32 dib;
+} __attribute__((__packed__));
+
+struct peci_get_temp_msg {
+ __u8 addr;
+ __s16 temp_raw;
+} __attribute__((__packed__));
+
+struct peci_rd_pkg_cfg_msg {
+ __u8 addr;
+ __u8 index;
+ __u16 param;
+ __u8 rx_len;
+ __u8 pkg_config[4];
+} __attribute__((__packed__));
+
+struct peci_wr_pkg_cfg_msg {
+ __u8 addr;
+ __u8 index;
+ __u16 param;
+ __u8 tx_len;
+ __u32 value;
+} __attribute__((__packed__));
+
+struct peci_rd_ia_msr_msg {
+ __u8 addr;
+ __u8 thread_id;
+ __u16 address;
+ __u64 value;
+} __attribute__((__packed__));
+
+struct peci_rd_pci_cfg_msg {
+ __u8 addr;
+ __u8 bus;
+ __u8 device;
+ __u8 function;
+ __u16 reg;
+ __u8 pci_config[4];
+} __attribute__((__packed__));
+
+struct peci_rd_pci_cfg_local_msg {
+ __u8 addr;
+ __u8 bus;
+ __u8 device;
+ __u8 function;
+ __u16 reg;
+ __u8 rx_len;
+ __u8 pci_config[4];
+} __attribute__((__packed__));
+
+struct peci_wr_pci_cfg_local_msg {
+ __u8 addr;
+ __u8 bus;
+ __u8 device;
+ __u8 function;
+ __u16 reg;
+ __u8 tx_len;
+ __u32 value;
+} __attribute__((__packed__));
+
+#define PECI_IOC_BASE 0xb7
+
+#define PECI_IOC_XFER \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_XFER, struct peci_xfer_msg)
+
+#define PECI_IOC_PING \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_PING, struct peci_ping_msg)
+
+#define PECI_IOC_GET_DIB \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_GET_DIB, struct peci_get_dib_msg)
+
+#define PECI_IOC_GET_TEMP \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_GET_TEMP, struct peci_get_temp_msg)
+
+#define PECI_IOC_RD_PKG_CFG \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_RD_PKG_CFG, struct peci_rd_pkg_cfg_msg)
+
+#define PECI_IOC_WR_PKG_CFG \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_WR_PKG_CFG, struct peci_wr_pkg_cfg_msg)
+
+#define PECI_IOC_RD_IA_MSR \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_RD_IA_MSR, struct peci_rd_ia_msr_msg)
+
+#define PECI_IOC_RD_PCI_CFG \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_RD_PCI_CFG, struct peci_rd_pci_cfg_msg)
+
+#define PECI_IOC_RD_PCI_CFG_LOCAL \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_RD_PCI_CFG_LOCAL, \
+ struct peci_rd_pci_cfg_local_msg)
+
+#define PECI_IOC_WR_PCI_CFG_LOCAL \
+ _IOWR(PECI_IOC_BASE, PECI_CMD_WR_PCI_CFG_LOCAL, \
+ struct peci_wr_pci_cfg_local_msg)
+
+#endif /* __PECI_IOCTL_H */
--
2.18.0
^ permalink raw reply related
* [PATCH v8 02/12] Documentation: ioctl: Add ioctl numbers for PECI subsystem
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit updates ioctl-number.txt to reflect ioctl numbers used
by the PECI subsystem.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Cc: Eric Sandeen <sandeen@redhat.com>
Cc: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: James Feist <james.feist@linux.intel.com>
Cc: Jason M Biils <jason.m.bills@linux.intel.com>
Cc: Vernon Mauery <vernon.mauery@linux.intel.com>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
Documentation/ioctl/ioctl-number.txt | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt
index 13a7c999c04a..d9577593647e 100644
--- a/Documentation/ioctl/ioctl-number.txt
+++ b/Documentation/ioctl/ioctl-number.txt
@@ -325,6 +325,8 @@ Code Seq#(hex) Include File Comments
0xB4 00-0F linux/gpio.h <mailto:linux-gpio@vger.kernel.org>
0xB5 00-0F uapi/linux/rpmsg.h <mailto:linux-remoteproc@vger.kernel.org>
0xB6 all linux/fpga-dfl.h
+0xB7 00-0F uapi/linux/peci-ioctl.h PECI subsystem
+ <mailto:jae.hyun.yoo@linux.intel.com>
0xC0 00-0F linux/usb/iowarrior.h
0xCA 00-0F uapi/misc/cxl.h
0xCA 10-2F uapi/misc/ocxl.h
--
2.18.0
^ permalink raw reply related
* [PATCH v8 01/12] dt-bindings: Add a document of PECI subsystem
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180918215124.14003-1-jae.hyun.yoo@linux.intel.com>
This commit adds a document of generic PECI bus, adapter and client
driver.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
---
.../devicetree/bindings/peci/peci.txt | 43 +++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/peci/peci.txt
diff --git a/Documentation/devicetree/bindings/peci/peci.txt b/Documentation/devicetree/bindings/peci/peci.txt
new file mode 100644
index 000000000000..864b7ab4e9fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/peci/peci.txt
@@ -0,0 +1,43 @@
+Generic device tree configuration for PECI adapters
+===================================================
+
+Required properties:
+- #address-cells : Should be <1>. Read more about client addresses below.
+- #size-cells : Should be <0>. Read more about client addresses below.
+
+The cells properties above define that an address of CPU clients of a PECI bus
+are described by a single value.
+
+Example:
+ peci0: peci-bus at 0 {
+ compatible = "vendor,soc-peci";
+ reg = <0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+Generic device tree configuration for PECI clients
+==================================================
+
+Required properties:
+- compatible : Should contain name of PECI client.
+- reg : Should contain address of a client CPU. Address range of CPU
+ clients starts from 0x30 based on PECI specification.
+
+Example:
+ peci-bus at 0 {
+ compatible = "vendor,soc-peci";
+ reg = <0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ peci-client at 30 {
+ compatible = "intel,peci-client";
+ reg = <0x30>;
+ };
+
+ peci-client at 31 {
+ compatible = "intel,peci-client";
+ reg = <0x31>;
+ };
+ };
--
2.18.0
^ permalink raw reply related
* [PATCH v8 00/12] PECI device driver introduction
From: Jae Hyun Yoo @ 2018-09-18 21:51 UTC (permalink / raw)
To: linux-aspeed
Introduction of the Platform Environment Control Interface (PECI) bus
device driver. PECI is a one-wire bus interface that provides a
communication channel from Intel processors and chipset components to
external monitoring or control devices. PECI is designed to support the
following sideband functions:
* Processor and DRAM thermal management
- Processor fan speed control is managed by comparing Digital Thermal
Sensor (DTS) thermal readings acquired via PECI against the
processor-specific fan speed control reference point, or TCONTROL. Both
TCONTROL and DTS thermal readings are accessible via the processor PECI
client. These variables are referenced to a common temperature, the TCC
activation point, and are both defined as negative offsets from that
reference.
- PECI based access to the processor package configuration space provides
a means for Baseboard Management Controllers (BMC) or other platform
management devices to actively manage the processor and memory power
and thermal features.
* Platform Manageability
- Platform manageability functions including thermal, power, and error
monitoring. Note that platform 'power' management includes monitoring
and control for both the processor and DRAM subsystem to assist with
data center power limiting.
- PECI allows read access to certain error registers in the processor MSR
space and status monitoring registers in the PCI configuration space
within the processor and downstream devices.
- PECI permits writes to certain registers in the processor PCI
configuration space.
* Processor Interface Tuning and Diagnostics
- Processor interface tuning and diagnostics capabilities
(Intel Interconnect BIST). The processors Intel Interconnect Built In
Self Test (Intel IBIST) allows for infield diagnostic capabilities in
the Intel UPI and memory controller interfaces. PECI provides a port to
execute these diagnostics via its PCI Configuration read and write
capabilities.
* Failure Analysis
- Output the state of the processor after a failure for analysis via
Crashdump.
PECI uses a single wire for self-clocking and data transfer. The bus
requires no additional control lines. The physical layer is a self-clocked
one-wire bus that begins each bit with a driven, rising edge from an idle
level near zero volts. The duration of the signal driven high depends on
whether the bit value is a logic '0' or logic '1'. PECI also includes
variable data transfer rate established with every message. In this way, it
is highly flexible even though underlying logic is simple.
The interface design was optimized for interfacing between an Intel
processor and chipset components in both single processor and multiple
processor environments. The single wire interface provides low board
routing overhead for the multiple load connections in the congested routing
area near the processor and chipset components. Bus speed, error checking,
and low protocol overhead provides adequate link bandwidth and reliability
to transfer critical device operating conditions and configuration
information.
This implementation provides the basic framework to add PECI extensions to
the Linux bus and device models. A hardware specific 'Adapter' driver can
be attached to the PECI bus to provide sideband functions described above.
It is also possible to access all devices on an adapter from userspace
through the /dev interface. A device specific 'Client' driver also can be
attached to the PECI bus so each processor client's features can be
supported by the 'Client' driver through an adapter connection in the bus.
This patch set includes Aspeed 24xx/25xx PECI driver and PECI
cputemp/dimmtemp drivers as the first implementation for both adapter and
client drivers on the PECI bus framework.
Please review.
Thanks,
Jae
Changes since v7:
- Fixed a typo in the MFD_INTEL_PECI_CLIENT description.
- Made peci_unregister_device() NULL-aware.
- Converted to using %pOF instead of node full name in peci-core.
- Removed OF tables from peci-cputemp and peci-dimmtemp.
- Removed of_compatible strings from intel-peci-client.
- Added an access_ok() check into peci_ioctl in peci-core.
- Changed the DT node name of peci simple-bus from 'peci' to 'bus'.
Changes since v6:
- Dropped off unnecessary examples from dt-bindings document.
- Fixed a bug in DIMM index mask building logic.
- Modified DIMM temp label strings to match with the way in BIOS.
- Changed PECI ioctl base number from B6 to B7 to avoid conflict with
fpga-dfl.
- Seperated the PECI section in MAINTAINERS into two parts - PECI subsystem
and ASPEED PECI driver.
Changes since v5:
- Added more detailed descriptions for PECI client MFD documents.
- Changed PECI client MFD souce file names.
- Fixed DT example of PECI client MFD.
- Removed unnecessary debug printings.
- Moved the asm/intel-family.h inclusion place.
Changes since v4:
- Fixed an incorrect endianness handling in peci-aspeed.
- Added a comment to explain about the asm/intel-family.h inclusion.
- Added an MFD module to support multi-function PECI client devices.
Changes since v3:
- Made code more simple and compact.
- Removed unused header file inclusion.
- Fixed incorrect error return values and messages.
- Removed DTS margin temperature from the peci-cputemp.
- Made some magic numbers use defines.
- Moved peci_get_cpu_id() into peci-core as a common function.
- Replaced the cancel_delayed_work() call with a cancel_delayed_work_sync().
- Replaced AST and Aspeed uses with ASPEED.
- Simplified peci command timeout checking logic using
regmap_read_poll_timeout().
- Simplified endian swap codes using endian handling macros.
- Dropped regmap read/write error checking except for the first access.
- Added a PECI reset setting in the device tree node.
- Removed unnecessary sleep from the probe context.
- Removed IRQF_SHARED flag from irq request code in the ASPEED PECI driver.
- Fixed typos in documents.
- Combined peci-bus.txt, peci-adapter.txt and peci-client.txt into peci.txt.
- Fixed and swept documents to drop some incorrect or unnecessary
descriptions.
- Fixed device tree to make unit-address format use reg contents.
- Simplified bit manipulations using <linux/bitfield.h>.
- Made client CPU model checking use <asm/intel-family.h> if available.
- Modified adapter heap allocation method to use kobject reference count
based.
- Added the low-level PECI xfer IOCTL again to support the Redfish
requirement.
- Added PM domain attach/detach code.
- Added logic for device instantiation through sysfs.
- Fix a bug of interrupt status checking code in peci-aspeed driver.
Changes since v2:
- Divided peci-hwmon driver into two drivers, peci-cputemp and
peci-dimmtemp.
- Added generic dt binding documents for PECI bus, adapter and client.
- Removed in_atomic() call from the PECI core driver.
- Improved PECI commands masking logic.
- Added permission check logic for PECI ioctls.
- Removed unnecessary type casts.
- Fixed some invalid error return codes.
- Added the mark_updated() function to improve update interval checking
logic.
- Fixed a bug in populated DIMM checking function.
- Fixed some typo, grammar and style issues in documents.
- Rewrote hwmon drivers to use devm_hwmon_device_register_with_info API.
- Made peci_match_id() function as a static.
- Replaced a deprecated create_singlethread_workqueue() call with an
alloc_ordered_workqueue() call.
- Reordered local variable definitions in reversed xmas tree notation.
- Listed up client CPUs that can be supported by peci-cputemp and
peci-dimmtemp hwmon drivers.
- Added CPU generation detection logic which checks CPUID signature through
PECI connection.
- Improved interrupt handling logic in the Aspeed PECI adapter driver.
- Fixed SPDX license identifier style in header files.
- Changed some macros in peci.h to static inline functions.
- Dropped sleepable context checking code in peci-core.
- Adjusted rt_mutex protection scope in peci-core.
- Moved adapter->xfer() checking code into peci_register_adapter().
- Improved PECI command retry checking logic.
- Changed ioctl base from 'P' to 0xb6 to avoid confiliction and updated
ioctl-number.txt to reflect the ioctl number of PECI subsystem.
- Added a comment to describe PECI retry action.
- Simplified return code handling of peci_ioctl_ping().
- Changed type of peci_ioctl_fn[] to static const.
- Fixed range checking code for valid PECI commands.
- Fixed the error return code on invalid PECI commands.
- Fixed incorrect definitions of PECI ioctl and its handling logic.
Changes since v1:
- Additionally implemented a core driver to support PECI linux bus driver
model.
- Modified Aspeed PECI driver to make that to be an adapter driver in PECI
bus.
- Modified PECI hwmon driver to make that to be a client driver in PECI
bus.
- Simplified hwmon driver attribute labels and removed redundant strings.
- Removed core_nums from device tree setting of hwmon driver and modified
core number detection logic to check the resolved_core register in client
CPU's local PCI configuration area.
- Removed dimm_nums from device tree setting of hwmon driver and added
populated DIMM detection logic to support dynamic creation.
- Removed indexing gap on core temperature and DIMM temperature attributes.
- Improved hwmon registration and dynamic attribute creation logic.
- Fixed structure definitions in PECI uapi header to make that use __u8,
__u16 and etc.
- Modified wait_for_completion_interruptible_timeout error handling logic
in Aspeed PECI driver to deliver errors correctly.
- Removed low-level xfer command from ioctl and kept only high-level PECI
command suite as ioctls.
- Fixed I/O timeout logic in Aspeed PECI driver using ktime.
- Added a function into hwmon driver to simplify update delay checking.
- Added a function into hwmon driver to convert 10.6 to millidegree.
- Dropped non-standard attributes in hwmon driver.
- Fixed OF table for hwmon to make it indicate as a PECI client of Intel
CPU target.
- Added a maintainer of PECI subsystem into MAINTAINERS document.
Jae Hyun Yoo (12):
dt-bindings: Add a document of PECI subsystem
Documentation: ioctl: Add ioctl numbers for PECI subsystem
peci: Add support for PECI bus driver core
dt-bindings: Add a document of PECI adapter driver for ASPEED
AST24xx/25xx SoCs
ARM: dts: aspeed: peci: Add PECI node
peci: Add a PECI adapter driver for Aspeed AST24xx/AST25xx
dt-bindings: mfd: Add a document for PECI client MFD
mfd: intel-peci-client: Add PECI client MFD driver
Documentation: hwmon: Add documents for PECI hwmon client drivers
hwmon: Add PECI cputemp driver
hwmon: Add PECI dimmtemp driver
Add maintainers for the PECI subsystem
.../bindings/mfd/intel-peci-client.txt | 34 +
.../devicetree/bindings/peci/peci-aspeed.txt | 55 +
.../devicetree/bindings/peci/peci.txt | 43 +
Documentation/hwmon/peci-cputemp | 78 +
Documentation/hwmon/peci-dimmtemp | 50 +
Documentation/ioctl/ioctl-number.txt | 2 +
MAINTAINERS | 13 +
arch/arm/boot/dts/aspeed-g4.dtsi | 26 +
arch/arm/boot/dts/aspeed-g5.dtsi | 26 +
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/hwmon/Kconfig | 28 +
drivers/hwmon/Makefile | 2 +
drivers/hwmon/peci-cputemp.c | 392 +++++
drivers/hwmon/peci-dimmtemp.c | 286 ++++
drivers/mfd/Kconfig | 14 +
drivers/mfd/Makefile | 1 +
drivers/mfd/intel-peci-client.c | 181 +++
drivers/peci/Kconfig | 39 +
drivers/peci/Makefile | 9 +
drivers/peci/peci-aspeed.c | 498 ++++++
drivers/peci/peci-core.c | 1440 +++++++++++++++++
include/linux/mfd/intel-peci-client.h | 81 +
include/linux/peci.h | 104 ++
include/uapi/linux/peci-ioctl.h | 265 +++
25 files changed, 3670 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/intel-peci-client.txt
create mode 100644 Documentation/devicetree/bindings/peci/peci-aspeed.txt
create mode 100644 Documentation/devicetree/bindings/peci/peci.txt
create mode 100644 Documentation/hwmon/peci-cputemp
create mode 100644 Documentation/hwmon/peci-dimmtemp
create mode 100644 drivers/hwmon/peci-cputemp.c
create mode 100644 drivers/hwmon/peci-dimmtemp.c
create mode 100644 drivers/mfd/intel-peci-client.c
create mode 100644 drivers/peci/Kconfig
create mode 100644 drivers/peci/Makefile
create mode 100644 drivers/peci/peci-aspeed.c
create mode 100644 drivers/peci/peci-core.c
create mode 100644 include/linux/mfd/intel-peci-client.h
create mode 100644 include/linux/peci.h
create mode 100644 include/uapi/linux/peci-ioctl.h
--
2.18.0
^ permalink raw reply
* [RFC PATCH i2c-next 1/2] dt-bindings: i2c: aspeed: Add 'idle-wait-timeout-ms' setting
From: Jae Hyun Yoo @ 2018-09-18 18:02 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180910214519.14126-2-jae.hyun.yoo@linux.intel.com>
On 9/10/2018 2:45 PM, Jae Hyun Yoo wrote:
> +- idle-wait-timeout-ms : bus idle waiting timeout in milliseconds when
> + multi-master is set, defaults to 100 ms when not
> + specified.
Will change it to 'aspeed,idle-wait-timeout-ms' as it's a non standard
property.
Jae
^ permalink raw reply
* [PATCH] i2c: aspeed: Acknowledge most interrupts early in interrupt handler
From: Brendan Higgins @ 2018-09-18 1:28 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <CACPK8XchoryZ_RS8f4n=-GoT-Ak+dXuC3cgqLmxK9C=gySEJFQ@mail.gmail.com>
On Mon, Sep 17, 2018 at 6:11 PM Joel Stanley <joel@jms.id.au> wrote:
>
> On Fri, 14 Sep 2018 at 13:00, Guenter Roeck <linux@roeck-us.net> wrote:
> >
> > Commit 3e9efc3299dd ("i2c: aspeed: Handle master/slave combined irq events
> > properly") moved interrupt acknowledgment to the end of the interrupt
> > handler. In part this was done because the AST2500 datasheet says:
> >
> > I2CD10 Interrupt Status Register
> > bit 2 Receive Done Interrupt status
> > S/W needs to clear this status bit to allow next data receiving.
> >
> > Acknowledging Receive Done before receive data was handled resulted in
> > receive errors on high speed I2C busses.
> >
> > However, interrupt acknowledgment was not only moved to the end of the
> > interrupt handler for Receive Done Interrupt status, but for all interrupt
> > status bits. This could result in race conditions if a second interrupt was
> > received during interrupt handling and not handled but still acknowledged
> > at the end of the interrupt handler.
> >
> > Acknowledge only "Receive Done Interrupt status" late in the interrupt
> > handler to solve the problem.
> >
> > Fixes: 3e9efc3299dd ("i2c: aspeed: Handle master/slave combined irq events properly")
> > Cc: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> > Cc: Joel Stanley <joel@jms.id.au>
> > Signed-off-by: Guenter Roeck <linux@roeck-us.net>
>
> Thanks for getting to the bottom of this Guenter. I gave it a spin on
> Romulus (ast2500) and Palmetto (ast2400) without issue.
>
> Tested-by: Joel Stanley <joel@jms.id.au>
>
Nice work! Thanks!
Acked-by: Brendan Higgins <brendanhiggins@google.com>
^ permalink raw reply
* [PATCH] i2c: aspeed: Acknowledge most interrupts early in interrupt handler
From: Joel Stanley @ 2018-09-18 1:11 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <1536895810-28903-1-git-send-email-linux@roeck-us.net>
On Fri, 14 Sep 2018 at 13:00, Guenter Roeck <linux@roeck-us.net> wrote:
>
> Commit 3e9efc3299dd ("i2c: aspeed: Handle master/slave combined irq events
> properly") moved interrupt acknowledgment to the end of the interrupt
> handler. In part this was done because the AST2500 datasheet says:
>
> I2CD10 Interrupt Status Register
> bit 2 Receive Done Interrupt status
> S/W needs to clear this status bit to allow next data receiving.
>
> Acknowledging Receive Done before receive data was handled resulted in
> receive errors on high speed I2C busses.
>
> However, interrupt acknowledgment was not only moved to the end of the
> interrupt handler for Receive Done Interrupt status, but for all interrupt
> status bits. This could result in race conditions if a second interrupt was
> received during interrupt handling and not handled but still acknowledged
> at the end of the interrupt handler.
>
> Acknowledge only "Receive Done Interrupt status" late in the interrupt
> handler to solve the problem.
>
> Fixes: 3e9efc3299dd ("i2c: aspeed: Handle master/slave combined irq events properly")
> Cc: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> Cc: Joel Stanley <joel@jms.id.au>
> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Thanks for getting to the bottom of this Guenter. I gave it a spin on
Romulus (ast2500) and Palmetto (ast2400) without issue.
Tested-by: Joel Stanley <joel@jms.id.au>
Cheers,
Joel
^ permalink raw reply
* [PATCH] i2c: aspeed: Acknowledge most interrupts early in interrupt handler
From: Guenter Roeck @ 2018-09-17 18:48 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <037b4cf8-5dfa-d554-b126-a2462ba9c803@linux.intel.com>
On Mon, Sep 17, 2018 at 10:16:59AM -0700, Jae Hyun Yoo wrote:
> On 9/17/2018 9:34 AM, Wolfram Sang wrote:
> >
> >>Looks good to me. Thanks! :)
> >>
> >>Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> >
> >Does that mean I need to revert "[PATCH i2c-next v6] i2c: aspeed: Handle
> >master/slave combined irq events properly" in i2c/for-next? And apply
> >this to i2c/for-current?
> >
>
> No need to revert "[PATCH i2c-next v6] i2c: aspeed: Handle master/slave
> combined irq events properly". This patch should be applied on top of
> the patch.
>
Yes, sorry, I should have tagged the patch as for-next.
Guenter
^ permalink raw reply
* [PATCH] i2c: aspeed: Acknowledge most interrupts early in interrupt handler
From: Jae Hyun Yoo @ 2018-09-17 17:16 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180917163401.GA1082@kunai>
On 9/17/2018 9:34 AM, Wolfram Sang wrote:
>
>> Looks good to me. Thanks! :)
>>
>> Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
>
> Does that mean I need to revert "[PATCH i2c-next v6] i2c: aspeed: Handle
> master/slave combined irq events properly" in i2c/for-next? And apply
> this to i2c/for-current?
>
> (and please quote only relevat parts of a message when replying)
>
No need to revert "[PATCH i2c-next v6] i2c: aspeed: Handle master/slave
combined irq events properly". This patch should be applied on top of
the patch.
(Will reduce message size when replying. Thanks!)
Jae
^ permalink raw reply
* [PATCH] i2c: aspeed: Acknowledge most interrupts early in interrupt handler
From: Wolfram Sang @ 2018-09-17 16:34 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <fbf54ca6-16b3-5e35-eac8-b3dab8118543@linux.intel.com>
> Looks good to me. Thanks! :)
>
> Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Does that mean I need to revert "[PATCH i2c-next v6] i2c: aspeed: Handle
master/slave combined irq events properly" in i2c/for-next? And apply
this to i2c/for-current?
(and please quote only relevat parts of a message when replying)
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <http://lists.ozlabs.org/pipermail/linux-aspeed/attachments/20180917/7cb37b53/attachment.sig>
^ permalink raw reply
* [PATCH] ARM: dts: aspeed: Adding Facebook TioagaPass BMC
From: Rob Herring @ 2018-09-17 3:53 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180913195751.1833227-1-vijaykhemka@fb.com>
On Thu, Sep 13, 2018 at 12:57:51PM -0700, Vijay Khemka wrote:
> Initial introduction of Facebook TioagaPass family equipped with
> Aspeed 2500 BMC SoC. Neptune is a x86 server development kit
> with a ASPEED ast2500 BMC manufactured by Facebook.
> Specifically, This adds the tiogapass platform device tree file
> including the flash layout used by the tiogapass BMC machines.
>
> This also adds an entry of tiogapass device tree file in Makefile
> as well an entry of Facebook in Documentation for vendor prefix
>
> Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
> ---
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> .../dts/aspeed-bmc-facebook-tiogapass.dts | 152 ++++++++++++++++++
> 3 files changed, 154 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 2c3fc512e746..733b2d523642 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -127,6 +127,7 @@ everspin Everspin Technologies, Inc.
> exar Exar Corporation
> excito Excito
> ezchip EZchip Semiconductor
> +facebook Facebook
> fairphone Fairphone B.V.
> faraday Faraday Technology Corporation
> fastrax Fastrax Oy
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b5bd3de87c33..9c82c1681c38 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1206,4 +1206,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-opp-witherspoon.dtb \
> aspeed-bmc-opp-zaius.dtb \
> aspeed-bmc-portwell-neptune.dtb \
> + aspeed-bmc-facebook-tiogapass.dtb \
> aspeed-bmc-quanta-q71l.dtb
> diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
> new file mode 100644
> index 000000000000..859a00581e34
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
> @@ -0,0 +1,152 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (c) 2017 Facebook Inc.
> +/dts-v1/;
> +
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "Facebook TiogaPass BMC";
> + compatible = "facebook,tiogapass-bmc", "aspeed,ast2500";
> + aliases {
> + serial0 = &uart1;
> + serial4 = &uart5;
> + };
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200 earlyprintk";
> + };
> +
> + memory {
This should have a unit-address (as should whatever is defined in
aspeed-g5.dtsi).
> + reg = <0x80000000 0x20000000>;
> + };
^ permalink raw reply
* [PATCH] ARM: dts: aspeed: Adding Facebook TioagaPass BMC
From: Vijay Khemka @ 2018-09-14 18:57 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <20180913201739.GG23892@lunn.ch>
Thanks Andrew,
I have revised patch as I found some more changes. Sent a new version.
Regards
-Vijay
?On 9/13/18, 1:18 PM, "Andrew Lunn" <andrew@lunn.ch> wrote:
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1206,4 +1206,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-opp-witherspoon.dtb \
> aspeed-bmc-opp-zaius.dtb \
> aspeed-bmc-portwell-neptune.dtb \
> + aspeed-bmc-facebook-tiogapass.dtb \
Hi Vijay
These entries are normally kept in alphabetic order.
> + leds {
> + compatible = "gpio-leds";
> + postcode0 {
> + label="BMC_UP";
Documentation/leds/leds-class.txt
LED Device Naming
=================
Is currently of the form:
"devicename:colour:function"
Andrew
^ permalink raw reply
* [PATCH v2 2/2] media: platform: Add Aspeed Video Engine driver
From: Hans Verkuil @ 2018-09-14 17:31 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <cf333297-cc02-51c7-14a0-4d35bc1f8f07@linux.vnet.ibm.com>
On 09/14/2018 05:22 PM, Eddie James wrote:
>>> +static int aspeed_video_allocate_cma(struct aspeed_video *video)
>>> +{
>>> + video->srcs[0].virt = dma_alloc_coherent(video->dev,
>>> + VE_SRC_BUFFER_SIZE,
>>> + &video->srcs[0].dma,
>>> + GFP_KERNEL);
>>> + if (!video->srcs[0].virt) {
>>> + dev_err(video->dev,
>>> + "Failed to allocate source buffer 0, size[%x]\n",
>>> + VE_SRC_BUFFER_SIZE);
>>> + goto err;
>>> + }
>>> +
>>> + video->srcs[1].virt = dma_alloc_coherent(video->dev,
>>> + VE_SRC_BUFFER_SIZE,
>>> + &video->srcs[1].dma,
>>> + GFP_KERNEL);
>>> + if (!video->srcs[1].virt) {
>>> + dev_err(video->dev,
>>> + "Failed to allocate source buffer 1, size[%x]\n",
>>> + VE_SRC_BUFFER_SIZE);
>>> + goto free_src0;
>>> + }
>>> +
>>> + video->comp[0].virt = dma_alloc_coherent(video->dev,
>>> + VE_COMP_BUFFER_SIZE,
>>> + &video->comp[0].dma,
>>> + GFP_KERNEL);
>>> + if (!video->comp[0].virt) {
>>> + dev_err(video->dev,
>>> + "Failed to allocate compression buffer 0, size[%x]\n",
>>> + VE_COMP_BUFFER_SIZE);
>>> + goto free_src1;
>>> + }
>>> +
>>> + video->comp[1].virt = dma_alloc_coherent(video->dev,
>>> + VE_COMP_BUFFER_SIZE,
>>> + &video->comp[1].dma,
>>> + GFP_KERNEL);
>>> + if (!video->comp[0].virt) {
Should be comp[1]!
>>> + dev_err(video->dev,
>>> + "Failed to allocate compression buffer 1, size[%x]\n",
>>> + VE_COMP_BUFFER_SIZE);
>>> + goto free_comp0;
>>> + }
>>> +
>>> + video->jpeg.virt = dma_alloc_coherent(video->dev, VE_JPEG_BUFFER_SIZE,
>>> + &video->jpeg.dma, GFP_KERNEL);
>>> + if (!video->jpeg.virt) {
>>> + dev_err(video->dev,
>>> + "Failed to allocate JPEG buffer, size[%x]\n",
>>> + VE_JPEG_BUFFER_SIZE);
>>> + goto free_comp1;
>>> + }
>> It looks like the buffers are allocated for a worst-case scenario (1080p I think).
>> So for smaller resolutions this wastes memory, but on the other hand you don't
>> need to reallocate buffers when the resolution changes.
>>
>> Am I right?
>
> That's correct. The other issue is that the buffers must be large enough
> to capture the frame when detecting the resolution. So at the beginning,
> they must be maximum size. I suppose once resolution is detected they
> can be freed and re-allocated for the correct size.
So looking at the code above we have two buffers of size VE_SRC_BUFFER_SIZE,
but what are the other 'comp' buffers and 'jpeg' buffer for?
It looks like this is a two-step process: first capture in the source buffers,
then compress into the 'comp' buffer, and that's then used by read().
I think that the jpeg buffer is for the jpeg header?
When implementing stream I/O you only need to allocate the compressed buffers.
The raw buffers can still be allocated as you do here.
The question with compressed formats is always what a good sizeimage value is,
since it has to be large enough for a worst-case scenario, and that's not
always easy to deduce.
>
>>
>>> +
>>> + aspeed_video_init_jpeg_table(video->jpeg.virt, video->yuv420);
>>> +
>>> + /*
>>> + * Calculate the memory restrictions. Don't consider the JPEG header
>>> + * buffer since HW doesn't need to write to it.
>>> + */
>>> + video->max = max(video->srcs[0].dma + VE_SRC_BUFFER_SIZE,
>>> + video->srcs[1].dma + VE_SRC_BUFFER_SIZE);
>>> + video->max = max(video->max, video->comp[0].dma + VE_COMP_BUFFER_SIZE);
>>> + video->max = max(video->max, video->comp[1].dma + VE_COMP_BUFFER_SIZE);
>>> +
>>> + video->min = min(video->srcs[0].dma, video->srcs[1].dma);
>>> + video->min = min(video->min, video->comp[0].dma);
>>> + video->min = min(video->min, video->comp[1].dma);
>>> +
>>> + return 0;
>>> +
>>> +free_comp1:
>>> + dma_free_coherent(video->dev, VE_COMP_BUFFER_SIZE, video->comp[1].virt,
>>> + video->comp[1].dma);
>>> + video->comp[1].dma = 0ULL;
>>> + video->comp[1].virt = NULL;
>>> +
>>> +free_comp0:
>>> + dma_free_coherent(video->dev, VE_COMP_BUFFER_SIZE, video->comp[0].virt,
>>> + video->comp[0].dma);
>>> + video->comp[0].dma = 0ULL;
>>> + video->comp[0].virt = NULL;
>>> +
>>> +free_src1:
>>> + dma_free_coherent(video->dev, VE_SRC_BUFFER_SIZE, video->srcs[1].virt,
>>> + video->srcs[1].dma);
>>> + video->srcs[1].dma = 0ULL;
>>> + video->srcs[1].virt = NULL;
>>> +
>>> +free_src0:
>>> + dma_free_coherent(video->dev, VE_SRC_BUFFER_SIZE, video->srcs[0].virt,
>>> + video->srcs[0].dma);
>>> + video->srcs[0].dma = 0ULL;
>>> + video->srcs[0].virt = NULL;
>>> +err:
>>> + return -ENOMEM;
>>> +}
>>> +
>>> +static void aspeed_video_free_cma(struct aspeed_video *video)
>>> +{
>>> + dma_free_coherent(video->dev, VE_JPEG_BUFFER_SIZE, video->jpeg.virt,
>>> + video->jpeg.dma);
>>> + dma_free_coherent(video->dev, VE_COMP_BUFFER_SIZE, video->comp[1].virt,
>>> + video->comp[1].dma);
>>> + dma_free_coherent(video->dev, VE_COMP_BUFFER_SIZE, video->comp[0].virt,
>>> + video->comp[0].dma);
>>> + dma_free_coherent(video->dev, VE_SRC_BUFFER_SIZE, video->srcs[1].virt,
>>> + video->srcs[1].dma);
>>> + dma_free_coherent(video->dev, VE_SRC_BUFFER_SIZE, video->srcs[0].virt,
>>> + video->srcs[0].dma);
>>> +
>>> + video->srcs[0].dma = 0ULL;
>>> + video->srcs[0].virt = NULL;
>>> + video->srcs[1].dma = 0ULL;
>>> + video->srcs[1].virt = NULL;
>>> + video->comp[0].dma = 0ULL;
>>> + video->comp[0].virt = NULL;
>>> + video->comp[1].dma = 0ULL;
>>> + video->comp[1].virt = NULL;
>>> + video->jpeg.dma = 0ULL;
>>> + video->jpeg.virt = NULL;
>>> +}
>>> +
>>> +static int aspeed_video_start(struct aspeed_video *video)
>>> +{
>>> + int rc = aspeed_video_allocate_cma(video);
>>> +
>>> + if (rc)
>>> + return rc;
>>> +
>>> + aspeed_video_on(video);
>>> +
>>> + aspeed_video_init_regs(video);
>>> +
>>> + rc = aspeed_video_get_resolution(video);
>>> + if (rc)
>>> + aspeed_video_free_cma(video);
>>> +
>>> + video->v4l2_fmt.fmt.pix.width = video->width;
>>> + video->v4l2_fmt.fmt.pix.height = video->height;
>>> + video->v4l2_fmt.fmt.pix.sizeimage = video->width * video->height * 4;
>> If you use JPEG compression, why is sizeimage set to the raw image size?
>> That's for an extreme case where JPEG can't compress the image at all?
>> But would this be too small in that situation since it doesn't have room
>> for the JPEG header?
>
> The size of the JPEG frame changes every frame, so this has to be set to
> the worst-case. I'm not sure if there is any data that JPEG cannot
> compress at all, but if that was the case then yes, the size would be
> too small. As the driver currently sits though, it would be larger than
> the "compressed frame" buffer long before that point though, so you'd
> just end up with an incomplete JPEG.
>>
>>> +
>>> + clear_bit(VIDEO_FRAME_TRIGGERED, &video->flags);
>>> +
>>> + return rc;
>>> +}
>>> +
>>> +static void aspeed_video_stop(struct aspeed_video *video)
>>> +{
>>> + cancel_delayed_work_sync(&video->res_work);
>>> +
>>> + aspeed_video_off(video);
>>> +
>>> + aspeed_video_free_cma(video);
>>> +
>>> + clear_bit(VIDEO_FRAME_AVAILABLE, &video->flags);
>>> +}
>>> +
>>> +static int aspeed_video_querycap(struct file *file, void *fh,
>>> + struct v4l2_capability *cap)
>>> +{
>>> + strlcpy(cap->driver, DEVICE_NAME, sizeof(cap->driver));
>>> + strlcpy(cap->card, "Aspeed Video Engine", sizeof(cap->card));
>> Use strscpy instead of strlcpy (just rename).
>>
>> The plan is that strscpy will replace all strcpy, strncpy and strlcpy usages
>> in the kernel.
>
> Ah, must be a recent change, as you recommended strlcpy last week :)
It is, actually. Just 5 days ago :-)
>>> +static int aspeed_video_set_parm(struct file *file, void *fh,
>>> + struct v4l2_streamparm *a)
>>> +{
>>> + int frame_rate;
>> unsigned int.
>>
>>> + struct aspeed_video *video = video_drvdata(file);
>>> +
>>> + if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
>>> + return -EINVAL;
>> Same here: just drop the check, it's not needed.
>>
>>> +
>>> + a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
>>> +
>>> + if (a->parm.capture.timeperframe.numerator) {
>>> + frame_rate = a->parm.capture.timeperframe.denominator /
>>> + a->parm.capture.timeperframe.numerator;
>> frame_rate can be 0 if denominator is 0,
>>
>>> + } else {
>>> + frame_rate = 0;
>>> + a->parm.capture.timeperframe.numerator = 1;
>> and then this isn't set to 1.
>>
>> v4l2-compliance was missing a test for this. I've added one, so I think it
>> should now fail when run against this driver. Could you test that?
>
> Well I had to do this to pass compliance actually, as it failed the test
> if either denominator or numerator is 0...
>
>>
>>> + }
>>> +
>>> + if (frame_rate < 0 || frame_rate > MAX_FRAME_RATE)
>>> + frame_rate = 0;
>>> +
>>> + if (!frame_rate)
>>> + a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE + 1;
>> Why MAX_FRAME_RATE + 1 and not MAX_FRAME_RATE?
>
> To get around compliance requiring non-zero and still preserving the
> frame rate info; if it's greater than frame rate, it gets set to 0.
>
> We need to be able to set a frame rate of 0, as that tells the engine,
> "as fast as possible".
Why not set frame_rate <= 0 and frame_rate > MAX_FRAME_RATE to MAX_FRAME_RATE?
And also if both num and demon are 0, then set frame_rate to MAX_FRAME_RATE
as well.
That should work just fine. If v4l2-compliance still complains, let me know
what it says.
>
>>
>>> +
>>> + if (video->frame_rate != frame_rate) {
>>> + video->frame_rate = frame_rate;
>>> + aspeed_video_update(video, VE_CTRL, ~VE_CTRL_FRC,
>>> + FIELD_PREP(VE_CTRL_FRC, frame_rate));
>> So the frame rate is set by userspace and is not related to the actual
>> host graphics framerate?
>
> Correct.
>
>>
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int aspeed_video_enum_framesizes(struct file *file, void *fh,
>>> + struct v4l2_frmsizeenum *fsize)
>>> +{
>>> + struct aspeed_video *video = video_drvdata(file);
>>> +
>>> + if (fsize->pixel_format != V4L2_PIX_FMT_JPEG)
>>> + return -EINVAL;
>>> +
>>> + switch (fsize->index) {
>>> + case 0:
>>> + fsize->discrete.width = video->v4l2_fmt.fmt.pix.width;
>>> + fsize->discrete.height = video->v4l2_fmt.fmt.pix.height;
>>> + break;
>>> + case 1:
>>> + if (video->width == video->v4l2_fmt.fmt.pix.width &&
>>> + video->height == video->v4l2_fmt.fmt.pix.height)
>>> + return -EINVAL;
>>> +
>>> + fsize->discrete.width = video->width;
>>> + fsize->discrete.height = video->height;
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +
>>> + fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int aspeed_video_enum_frameintervals(struct file *file, void *fh,
>>> + struct v4l2_frmivalenum *fival)
>>> +{
>>> + struct aspeed_video *video = video_drvdata(file);
>>> +
>>> + if (fival->index)
>>> + return -EINVAL;
>>> +
>>> + if (fival->width != video->width || fival->height != video->height)
>>> + return -EINVAL;
>>> +
>>> + if (fival->pixel_format != V4L2_PIX_FMT_JPEG)
>>> + return -EINVAL;
>>> +
>>> + fival->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
>>> +
>>> + fival->stepwise.min.denominator = MAX_FRAME_RATE;
>>> + fival->stepwise.min.numerator = 1;
>>> + fival->stepwise.max.denominator = 1;
>>> + fival->stepwise.max.numerator = 1;
>>> + fival->stepwise.step = fival->stepwise.max;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct v4l2_ioctl_ops aspeed_video_ioctl_ops = {
>>> + .vidioc_querycap = aspeed_video_querycap,
>>> + .vidioc_enum_fmt_vid_cap = aspeed_video_enum_format,
>>> + .vidioc_g_fmt_vid_cap = aspeed_video_get_format,
>>> + .vidioc_s_fmt_vid_cap = aspeed_video_set_format,
>>> + .vidioc_try_fmt_vid_cap = aspeed_video_try_format,
>>> + .vidioc_enum_input = aspeed_video_enum_input,
>>> + .vidioc_g_input = aspeed_video_get_input,
>>> + .vidioc_s_input = aspeed_video_set_input,
>>> + .vidioc_g_parm = aspeed_video_get_parm,
>>> + .vidioc_s_parm = aspeed_video_set_parm,
>>> + .vidioc_enum_framesizes = aspeed_video_enum_framesizes,
>>> + .vidioc_enum_frameintervals = aspeed_video_enum_frameintervals,
>>> + .vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
>>> + .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
>>> +};
>>> +
>>> +static void aspeed_video_update_jpeg_quality(struct aspeed_video *video)
>>> +{
>>> + u32 comp_ctrl = FIELD_PREP(VE_COMP_CTRL_DCT_LUM, video->jpeg_quality) |
>>> + FIELD_PREP(VE_COMP_CTRL_DCT_CHR, video->jpeg_quality | 0x10);
>>> +
>>> + aspeed_video_update(video, VE_COMP_CTRL,
>>> + ~(VE_COMP_CTRL_DCT_LUM | VE_COMP_CTRL_DCT_CHR),
>>> + comp_ctrl);
>>> +}
>>> +
>>> +static void aspeed_video_update_subsampling(struct aspeed_video *video)
>>> +{
>>> + if (video->jpeg.virt)
>>> + aspeed_video_init_jpeg_table(video->jpeg.virt, video->yuv420);
>>> +
>>> + if (video->yuv420)
>>> + aspeed_video_update(video, VE_SEQ_CTRL, 0xFFFFFFFF,
>>> + VE_SEQ_CTRL_YUV420);
>>> + else
>>> + aspeed_video_update(video, VE_SEQ_CTRL, ~VE_SEQ_CTRL_YUV420,
>>> + 0);
>>> +}
>>> +
>>> +static int aspeed_video_set_ctrl(struct v4l2_ctrl *ctrl)
>>> +{
>>> + struct aspeed_video *video = container_of(ctrl->handler,
>>> + struct aspeed_video,
>>> + v4l2_ctrl);
>>> +
>>> + switch (ctrl->id) {
>>> + case V4L2_CID_JPEG_COMPRESSION_QUALITY:
>>> + if (video->jpeg_quality != ctrl->val) {
>> No need to check if the value is different: this is only called if the value is
>> indeed different.
>>
>>> + video->jpeg_quality = ctrl->val;
>>> + aspeed_video_update_jpeg_quality(video);
>>> + }
>>> + break;
>>> + case V4L2_CID_JPEG_CHROMA_SUBSAMPLING:
>>> + if (ctrl->val == V4L2_JPEG_CHROMA_SUBSAMPLING_420) {
>>> + if (!video->yuv420) {
>> Ditto.
>>
>>> + video->yuv420 = true;
>>> + aspeed_video_update_subsampling(video);
>>> + }
>>> + } else {
>>> + if (video->yuv420) {
>>> + video->yuv420 = false;
>>> + aspeed_video_update_subsampling(video);
>>> + }
>>> + }
>>> + break;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct v4l2_ctrl_ops aspeed_video_ctrl_ops = {
>>> + .s_ctrl = aspeed_video_set_ctrl,
>>> +};
>>> +
>>> +static void aspeed_video_resolution_work(struct work_struct *work)
>>> +{
>>> + int rc;
>>> + struct delayed_work *dwork = to_delayed_work(work);
>>> + struct aspeed_video *video = container_of(dwork, struct aspeed_video,
>>> + res_work);
>>> +
>>> + /* No clients remaining after delay */
>>> + if (atomic_read(&video->clients) == 0)
>>> + goto done;
>>> +
>>> + aspeed_video_on(video);
>>> +
>>> + aspeed_video_init_regs(video);
>>> +
>>> + rc = aspeed_video_get_resolution(video);
>>> + if (rc) {
>>> + dev_err(video->dev,
>>> + "resolution changed; couldn't get new resolution\n");
>>> + } else {
>>> + video->frame_idx = 0;
>>> + clear_bit(VIDEO_FRAME_TRIGGERED, &video->flags);
>>> + }
>>> +
>>> +done:
>>> + clear_bit(VIDEO_RES_CHANGE, &video->flags);
>>> + wake_up_interruptible_all(&video->wait);
>>> +}
>>> +
>>> +static bool aspeed_video_frame_available(struct aspeed_video *video)
>>> +{
>>> + if (!test_and_clear_bit(VIDEO_FRAME_AVAILABLE, &video->flags)) {
>>> + if (!test_bit(VIDEO_FRAME_TRIGGERED, &video->flags))
>>> + aspeed_video_start_frame(video);
>>> +
>>> + return false;
>>> + }
>>> +
>>> + return true;
>>> +}
>>> +
>>> +static ssize_t aspeed_video_file_read(struct file *file, char __user *buf,
>>> + size_t count, loff_t *ppos)
>>> +{
>>> + int rc;
>>> + int fidx;
>>> + size_t size;
>>> + struct aspeed_video *video = video_drvdata(file);
>>> +
>>> + if (mutex_lock_interruptible(&video->video_lock))
>>> + return -EINTR;
>>> +
>>> + if (file->f_flags & O_NONBLOCK) {
>>> + if (!aspeed_video_frame_available(video)) {
>>> + rc = -EAGAIN;
>>> + goto unlock;
>>> + } else {
>>> + goto ready;
>>> + }
>>> + }
>>> +
>>> + rc = wait_event_interruptible(video->wait,
>>> + aspeed_video_frame_available(video));
>>> + if (rc) {
>>> + rc = -EINTR;
>>> + goto unlock;
>>> + }
>>> +
>>> +ready:
>>> + fidx = video->frame_idx;
>>> + size = min_t(size_t, video->frame_size, count);
>>> + aspeed_video_start_frame(video);
>>> +
>>> + if (copy_to_user(buf, video->comp[fidx].virt, size)) {
>>> + rc = -EFAULT;
>>> + goto unlock;
>>> + }
>>> +
>>> + rc = size;
>>> +
>>> +unlock:
>>> + mutex_unlock(&video->video_lock);
>>> + return rc;
>>> +}
>>> +
>>> +static int aspeed_video_open(struct file *file)
>>> +{
>>> + int rc;
>>> + struct aspeed_video *video = video_drvdata(file);
>>> +
>>> + if (atomic_inc_return(&video->clients) == 1) {
>>> + rc = aspeed_video_start(video);
>>> + if (rc) {
>>> + dev_err(video->dev, "Failed to start video engine\n");
>>> + atomic_dec(&video->clients);
>>> + return rc;
>>> + }
>>> + }
>>> +
>>> + return v4l2_fh_open(file);
>>> +}
>>> +
>>> +static int aspeed_video_release(struct file *file)
>>> +{
>>> + int rc;
>>> + struct aspeed_video *video = video_drvdata(file);
>>> +
>>> + rc = v4l2_fh_release(file);
>>> +
>>> + if (atomic_dec_return(&video->clients) == 0)
>>> + aspeed_video_stop(video);
>>> +
>>> + return rc;
>>> +}
>>> +
>>> +static const struct v4l2_file_operations aspeed_video_v4l2_fops = {
>>> + .owner = THIS_MODULE,
>>> + .read = aspeed_video_file_read,
>>> + .poll = v4l2_ctrl_poll,
>>> + .unlocked_ioctl = video_ioctl2,
>>> + .open = aspeed_video_open,
>>> + .release = aspeed_video_release,
>>> +};
>>> +
>>> +static void aspeed_video_device_release(struct video_device *vdev)
>>> +{
>>> +}
>>> +
>>> +static int aspeed_video_setup_video(struct aspeed_video *video)
>>> +{
>>> + int rc;
>>> + u64 mask = ~(BIT(V4L2_JPEG_CHROMA_SUBSAMPLING_444) |
>>> + BIT(V4L2_JPEG_CHROMA_SUBSAMPLING_420));
>>> + struct v4l2_device *v4l2_dev = &video->v4l2_dev;
>>> + struct video_device *vdev = &video->vdev;
>>> +
>>> + rc = v4l2_device_register(video->dev, v4l2_dev);
>>> + if (rc) {
>>> + dev_err(video->dev, "Failed to register v4l2 device\n");
>>> + return rc;
>>> + }
>>> +
>>> + vdev->fops = &aspeed_video_v4l2_fops;
>>> + vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE;
>>> + vdev->v4l2_dev = v4l2_dev;
>>> + strncpy(vdev->name, DEVICE_NAME, sizeof(vdev->name));
>> strscpy
>>
>>> + vdev->vfl_type = VFL_TYPE_GRABBER;
>>> + vdev->vfl_dir = VFL_DIR_RX;
>>> + vdev->release = aspeed_video_device_release;
>> Use the video_device_release_empty helper instead. Now you can drop aspeed_video_device_release.
>>
>>> + vdev->ioctl_ops = &aspeed_video_ioctl_ops;
>>> + vdev->lock = &video->video_lock;
>>> +
>>> + video_set_drvdata(vdev, video);
>>> + rc = video_register_device(vdev, VFL_TYPE_GRABBER, 0);
>> This should be done last in probe(). After this call the video node appears and
>> can be used by userspace, so everything must be fully initialized and that's
>> not the case.
>
> OK, gotcha.
>
>>
>>> + if (rc) {
>>> + v4l2_device_unregister(v4l2_dev);
>>> + dev_err(video->dev, "Failed to register video device\n");
>>> + return rc;
>>> + }
>>> +
>>> + video->v4l2_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
>>> + video->v4l2_fmt.fmt.pix.pixelformat = V4L2_PIX_FMT_JPEG;
>>> + video->v4l2_fmt.fmt.pix.field = V4L2_FIELD_NONE;
>>> + video->v4l2_fmt.fmt.pix.colorspace = V4L2_COLORSPACE_JPEG;
>> COLORSPACE_JPEG is deprecated. Use V4L2_COLORSPACE_SRGB for pix.colorspace
>> and set pix.quantization to V4L2_QUANTIZATION_FULL_RANGE.
>>
>>> +
>>> + /* Don't fail the probe if controls init fails */
>>> + v4l2_ctrl_handler_init(&video->v4l2_ctrl, 2);
>>> +
>>> + v4l2_ctrl_new_std(&video->v4l2_ctrl, &aspeed_video_ctrl_ops,
>>> + V4L2_CID_JPEG_COMPRESSION_QUALITY, 0,
>>> + ASPEED_VIDEO_JPEG_NUM_QUALITIES - 1, 1, 0);
>>> +
>>> + v4l2_ctrl_new_std_menu(&video->v4l2_ctrl, &aspeed_video_ctrl_ops,
>>> + V4L2_CID_JPEG_CHROMA_SUBSAMPLING,
>>> + V4L2_JPEG_CHROMA_SUBSAMPLING_420, mask,
>>> + V4L2_JPEG_CHROMA_SUBSAMPLING_444);
>>> +
>>> + if (video->v4l2_ctrl.error) {
>>> + dev_info(video->dev, "Failed to init controls: %d\n",
>>> + video->v4l2_ctrl.error);
>>> + v4l2_ctrl_handler_free(&video->v4l2_ctrl);
>> You really need to return an error here, you shouldn't continue.
>
> Well, the JPEG controls aren't strictly necessary right? The driver will
> operate fine with the default settings.
If this fails, then you are so close to an out-of-memory situation that
things will fail very quickly anyway.
In addition, if you later add new controls and something is wrong in the
control definition, then you wouldn't see that either.
There is no need to be fancy here, an error should be returned.
>
>>
>>> + } else {
>>> + v4l2_dev->ctrl_handler = &video->v4l2_ctrl;
>>> + vdev->ctrl_handler = &video->v4l2_ctrl;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int aspeed_video_init(struct aspeed_video *video)
>>> +{
>>> + int irq;
>>> + int rc;
>>> + struct device *dev = video->dev;
>>> +
>>> + irq = irq_of_parse_and_map(dev->of_node, 0);
>>> + if (!irq) {
>>> + dev_err(dev, "Unable to find IRQ\n");
>>> + return -ENODEV;
>>> + }
>>> +
>>> + rc = devm_request_irq(dev, irq, aspeed_video_irq, IRQF_SHARED,
>>> + DEVICE_NAME, video);
>>> + if (rc < 0) {
>>> + dev_err(dev, "Unable to request IRQ %d\n", irq);
>>> + return rc;
>>> + }
>>> +
>>> + video->eclk = devm_clk_get(dev, "eclk");
>>> + if (IS_ERR(video->eclk)) {
>>> + dev_err(dev, "Unable to get ECLK\n");
>>> + return PTR_ERR(video->eclk);
>>> + }
>>> +
>>> + video->vclk = devm_clk_get(dev, "vclk");
>>> + if (IS_ERR(video->vclk)) {
>>> + dev_err(dev, "Unable to get VCLK\n");
>>> + return PTR_ERR(video->vclk);
>>> + }
>>> +
>>> + video->rst = devm_reset_control_get_exclusive(dev, NULL);
>>> + if (IS_ERR(video->rst)) {
>>> + dev_err(dev, "Unable to get VE reset\n");
>>> + return PTR_ERR(video->rst);
>>> + }
>>> +
>>> + rc = of_reserved_mem_device_init(dev);
>>> + if (rc) {
>>> + dev_err(dev, "Unable to reserve memory\n");
>>> + return rc;
>>> + }
>>> +
>>> + rc = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
>>> + if (rc) {
>>> + dev_err(dev, "Failed to set DMA mask\n");
>>> + of_reserved_mem_device_release(dev);
>>> + return rc;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int aspeed_video_probe(struct platform_device *pdev)
>>> +{
>>> + int rc;
>>> + struct resource *res;
>>> + struct aspeed_video *video = kzalloc(sizeof(*video), GFP_KERNEL);
>>> +
>>> + if (!video)
>>> + return -ENOMEM;
>>> +
>>> + video->frame_rate = 30;
>>> + video->dev = &pdev->dev;
>>> + mutex_init(&video->video_lock);
>>> + init_waitqueue_head(&video->wait);
>>> + INIT_DELAYED_WORK(&video->res_work, aspeed_video_resolution_work);
>>> +
>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> +
>>> + video->base = devm_ioremap_resource(video->dev, res);
>>> +
>>> + if (IS_ERR(video->base))
>>> + return PTR_ERR(video->base);
>>> +
>>> + rc = aspeed_video_init(video);
>>> + if (rc)
>>> + return rc;
>>> +
>>> + rc = aspeed_video_setup_video(video);
>>> + if (rc)
>>> + return rc;
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int aspeed_video_remove(struct platform_device *pdev)
>>> +{
>>> + struct device *dev = &pdev->dev;
>>> + struct v4l2_device *v4l2_dev = dev_get_drvdata(dev);
>>> + struct aspeed_video *video = to_aspeed_video(v4l2_dev);
>>> +
>>> + if (video->vdev.ctrl_handler)
>>> + v4l2_ctrl_handler_free(&video->v4l2_ctrl);
>>> +
>>> + video_unregister_device(&video->vdev);
>>> +
>>> + v4l2_device_unregister(v4l2_dev);
>>> +
>>> + of_reserved_mem_device_release(dev);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct of_device_id aspeed_video_of_match[] = {
>>> + { .compatible = "aspeed,ast2400-video-engine" },
>>> + { .compatible = "aspeed,ast2500-video-engine" },
>>> + {}
>>> +};
>>> +MODULE_DEVICE_TABLE(of, aspeed_video_of_match);
>>> +
>>> +static struct platform_driver aspeed_video_driver = {
>>> + .driver = {
>>> + .name = DEVICE_NAME,
>>> + .of_match_table = aspeed_video_of_match,
>>> + },
>>> + .probe = aspeed_video_probe,
>>> + .remove = aspeed_video_remove,
>>> +};
>>> +
>>> +module_platform_driver(aspeed_video_driver);
>>> +
>>> +MODULE_DESCRIPTION("ASPEED Video Engine Driver");
>>> +MODULE_AUTHOR("Eddie James");
>>> +MODULE_LICENSE("GPL v2");
>>>
>> I don't like the read() API here. It is not a real read() either since it assumes
>> userspace reads full frames at a time. But if you read e.g. one byte at a time,
>> then each byte is just the first byte of a different frame.
>
> Yea...
>
>>
>> I think we need to figure out how to make the stream I/O version just as fast
>> if not faster as the read() API.
>
> OK, I'll see what I can do.
>
> Thanks for the review!
> Eddie
>
>>
>> Regards,
>>
>> Hans
>>
>
Regards,
Hans
^ permalink raw reply
* [PATCH v2 0/2] media: platform: Add Aspeed Video Engine Driver
From: Hans Verkuil @ 2018-09-14 17:14 UTC (permalink / raw)
To: linux-aspeed
In-Reply-To: <1436d8d6-25ab-4bb8-5558-3e02fbe95e58@linux.vnet.ibm.com>
On 09/14/2018 05:08 PM, Eddie James wrote:
>
>
> On 09/14/2018 01:59 AM, Hans Verkuil wrote:
>> On 09/13/2018 09:29 PM, Eddie James wrote:
>>> The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs
>>> can capture and compress video data from digital or analog sources. With
>>> the Aspeed chip acting as a service processor, the Video Engine can
>>> capture the host processor graphics output.
>>>
>>> This series adds a V4L2 driver for the VE, providing a read() interface
>>> only. The driver triggers the hardware to capture the host graphics output
>>> and compress it to JPEG format.
>>>
>>>
>>> v4l2-compliance output:
>>>
>>> v4l2-compliance SHA : not available
>> There should be a SHA here. "not available" indicates that you didn't compile
>> from the git repository directly, and now I do not know how old this compliance
>> test is. Always compile from the latest git repo, never use a version from e.g.
>> a distro as they tend to be old and missing tests.
>>
>> It would be great if you can do this and reply with the new compliance output.
>
> Hmm, I did compile from the latest git repo (maybe a week old now), but
> maybe our cross complication setup is preventing that hash from being
> generated. Will try and get it.
You can also just report the git commit hash if you can't get it to work.
As long as I know from which source version it was built.
Regards,
Hans
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox