[PATCH V8 00/14] mmc: Add Command Queue support

[Adrian Hunter <adrian.hunter@intel.com>]

Hi

Here is V8 of the hardware command queue patches without the software
command queue patches, now using blk-mq and now with blk-mq support for
non-CQE I/O.

After the unacceptable debacle of the last release cycle, I expect an
immediate response to these patches.

HW CMDQ offers 25% - 50% better random multi-threaded I/O.  I see a slight
2% drop in sequential read speed but no change to sequential write.

Non-CQE blk-mq showed a 3% decrease in sequential read performance.  This
seemed to be coming from the inferior latency of running work items compared
with a dedicated thread.  Hacking blk-mq workqueue to be unbound reduced the
performance degradation from 3% to 1%.

While we should look at changing blk-mq to give better workqueue performance,
a bigger gain is likely to be made by adding a new host API to enable the
next already-prepared request to be issued directly from within ->done()
callback of the current request.


Changes since V7:
	Re-based
      mmc: core: Introduce host claiming by context
	Slightly simplified
      mmc: core: Add parameter use_blk_mq
	New patch.
      mmc: core: Remove unnecessary host claim
	New patch.
      mmc: core: Export mmc_start_bkops()
	New patch.
      mmc: core: Export mmc_start_request()
	New patch.
      mmc: block: Add CQE and blk-mq support
	Add blk-mq support for non_CQE requests

Changes since V6:
      mmc: core: Introduce host claiming by context
	New patch.
      mmc: core: Move mmc_start_areq() declaration
	Dropped because it has been applied
      mmc: block: Fix block status codes
	Dropped because it has been applied
      mmc: host: Add CQE interface
	Dropped because it has been applied
      mmc: core: Turn off CQE before sending commands
	Dropped because it has been applied
      mmc: block: Factor out mmc_setup_queue()
	New patch.
      mmc: block: Add CQE support
	Drop legacy support and add blk-mq support

Changes since V5:
	Re-based
      mmc: core: Add mmc_retune_hold_now()
	Dropped because it has been applied
      mmc: core: Add members to mmc_request and mmc_data for CQE's
	Dropped because it has been applied
      mmc: core: Move mmc_start_areq() declaration
	New patch at Ulf's request
      mmc: block: Fix block status codes
	Another un-related patch
      mmc: host: Add CQE interface
	Move recovery_notifier() callback to struct mmc_request
      mmc: core: Add support for handling CQE requests
	Roll __mmc_cqe_request_done() into mmc_cqe_request_done()
	Move function declarations requested by Ulf
      mmc: core: Remove unused MMC_CAP2_PACKED_CMD
	Dropped because it has been applied
      mmc: block: Add CQE support
	Add explanation to commit message
	Adjustment for changed recovery_notifier() callback
      mmc: cqhci: support for command queue enabled host
	Adjustment for changed recovery_notifier() callback
      mmc: sdhci-pci: Add CQHCI support for Intel GLK
	Add DCMD capability for Intel controllers except GLK

Changes since V4:
      mmc: core: Add mmc_retune_hold_now()
	Add explanation to commit message.
      mmc: host: Add CQE interface
	Add comments to callback declarations.
      mmc: core: Turn off CQE before sending commands
	Add explanation to commit message.
      mmc: core: Add support for handling CQE requests
	Add comments as requested by Ulf.
      mmc: core: Remove unused MMC_CAP2_PACKED_CMD
	New patch.
      mmc: mmc: Enable Command Queuing
	Adjust for removal of MMC_CAP2_PACKED_CMD.
	Add a comment about Packed Commands.
      mmc: mmc: Enable CQE's
	Remove un-necessary check for MMC_CAP2_CQE
      mmc: block: Use local variables in mmc_blk_data_prep()
	New patch.
      mmc: block: Prepare CQE data
	Adjust due to "mmc: block: Use local variables in mmc_blk_data_prep()"
	Remove priority setting.
	Add explanation to commit message.
      mmc: cqhci: support for command queue enabled host
	Fix transfer descriptor setting in cqhci_set_tran_desc() for 32-bit DMA

Changes since V3:
	Adjusted ...blk_end_request...() for new block status codes
	Fixed CQHCI transaction descriptor for "no DCMD" case

Changes since V2:
	Dropped patches that have been applied.
	Re-based
	Added "mmc: sdhci-pci: Add CQHCI support for Intel GLK"

Changes since V1:

	"Share mmc request array between partitions" is dependent
	on changes in "Introduce queue semantics", so added that
	and block fixes:

	Added "Fix is_waiting_last_req set incorrectly"
	Added "Fix cmd error reset failure path"
	Added "Use local var for mqrq_cur"
	Added "Introduce queue semantics"

Changes since RFC:

	Re-based on next.
	Added comment about command queue priority.
	Added some acks and reviews.


Adrian Hunter (13):
      mmc: core: Introduce host claiming by context
      mmc: core: Add support for handling CQE requests
      mmc: mmc: Enable Command Queuing
      mmc: mmc: Enable CQE's
      mmc: block: Use local variables in mmc_blk_data_prep()
      mmc: block: Prepare CQE data
      mmc: block: Factor out mmc_setup_queue()
      mmc: core: Add parameter use_blk_mq
      mmc: core: Remove unnecessary host claim
      mmc: core: Export mmc_start_bkops()
      mmc: core: Export mmc_start_request()
      mmc: block: Add CQE and blk-mq support
      mmc: sdhci-pci: Add CQHCI support for Intel GLK

Venkat Gopalakrishnan (1):
      mmc: cqhci: support for command queue enabled host

 drivers/mmc/Kconfig               |   11 +
 drivers/mmc/core/block.c          |  777 ++++++++++++++++++++++++-
 drivers/mmc/core/block.h          |    8 +
 drivers/mmc/core/bus.c            |    7 +
 drivers/mmc/core/core.c           |  265 ++++++++-
 drivers/mmc/core/core.h           |   14 +
 drivers/mmc/core/host.c           |    2 +
 drivers/mmc/core/host.h           |    4 +
 drivers/mmc/core/mmc.c            |   29 +
 drivers/mmc/core/mmc_ops.c        |    6 +-
 drivers/mmc/core/queue.c          |  479 +++++++++++++--
 drivers/mmc/core/queue.h          |   54 +-
 drivers/mmc/host/Kconfig          |   14 +
 drivers/mmc/host/Makefile         |    1 +
 drivers/mmc/host/cqhci.c          | 1154 +++++++++++++++++++++++++++++++++++++
 drivers/mmc/host/cqhci.h          |  240 ++++++++
 drivers/mmc/host/sdhci-pci-core.c |  154 ++++-
 include/linux/mmc/host.h          |   10 +-
 18 files changed, 3146 insertions(+), 83 deletions(-)
 create mode 100644 drivers/mmc/host/cqhci.c
 create mode 100644 drivers/mmc/host/cqhci.h


Regards
Adrian