Re: [RFC PATCH 03/11] vfs: Use init_kiocb() to initialise new IOCBs

[Christoph Hellwig <hch@infradead.org>]

On Fri, Jun 30, 2023 at 04:25:16PM +0100, David Howells wrote:
> A number of places that generate kiocbs didn't use init_sync_kiocb() to
> initialise the new kiocb.  Fix these to always use init_kiocb().
> 
> Note that aio and io_uring pass information in through ki_filp through an
> overlaid union before I can call init_kiocb(), so that gets reinitialised.
> I don't think it clobbers anything else.
> 
> After this point, IOCB_WRITE is only set by init_kiocb().

Nothing in this patch touches the VFS, so the subject line is
wrong.  And I think we're better off splitting it into one per
subsystem, which also allows documenting the exact changes.

Which includes now setting the flags from f_iocb_flags and setting
and I/O priority.  Please explain why this is harmless or even useful.

> diff --git a/drivers/block/loop.c b/drivers/block/loop.c
> index 37511d2b2caf..ea92235c5ba2 100644
> --- a/drivers/block/loop.c
> +++ b/drivers/block/loop.c
> @@ -439,16 +439,17 @@ static int lo_rw_aio(struct loop_device *lo, struct loop_cmd *cmd,
>  	}
>  	atomic_set(&cmd->ref, 2);
>  
> -	iov_iter_bvec(&iter, rw, bvec, nr_bvec, blk_rq_bytes(rq));
> +	iov_iter_bvec(&iter, rw == WRITE ? ITER_SOURCE : ITER_DEST,
> +		      bvec, nr_bvec, blk_rq_bytes(rq));

Given the cover letter I expect this is going to go away, but the
changes would probably a lot more readable if you had a helper
to convert from READ/WRITE to the iter flags inbetween.

Or maybe do it the other way - add a helper to init the 

> @@ -490,12 +491,12 @@ static int do_req_filebacked(struct loop_device *lo, struct request *rq)
>  		return lo_fallocate(lo, rq, pos, FALLOC_FL_PUNCH_HOLE);
>  	case REQ_OP_WRITE:
>  		if (cmd->use_aio)
> -			return lo_rw_aio(lo, cmd, pos, ITER_SOURCE);
> +			return lo_rw_aio(lo, cmd, pos, WRITE);
>  		else
>  			return lo_write_simple(lo, rq, pos);
>  	case REQ_OP_READ:
>  		if (cmd->use_aio)
> -			return lo_rw_aio(lo, cmd, pos, ITER_DEST);
> +			return lo_rw_aio(lo, cmd, pos, READ);

I don't think there is any need to pass the rw argument at all,
lo_rw_aio can just do an op_is_write(req_op(rq))

> -static int io_rw_init_file(struct io_kiocb *req, fmode_t mode)
> +static int io_rw_init_file(struct io_kiocb *req, unsigned int io_direction)
>  {
>  	struct io_rw *rw = io_kiocb_to_cmd(req, struct io_rw);
>  	struct kiocb *kiocb = &rw->kiocb;
>  	struct io_ring_ctx *ctx = req->ctx;
>  	struct file *file = req->file;
> +	fmode_t mode = (io_direction == WRITE) ? FMODE_WRITE : FMODE_READ;
>  	int ret;
>  
>  	if (unlikely(!file || !(file->f_mode & mode)))

I'd just move this check into the two callers, that way you can hard
code the mode instead of adding a conversion.