From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Subject: Re: [Bluez-users] IOGear GBU301 and Kernel 2.4.20 From: Marcel Holtmann To: tsw@johana.com Cc: BlueZ Mailing List In-Reply-To: <20040809231313.17901.qmail@web60806.mail.yahoo.com> References: <20040809231313.17901.qmail@web60806.mail.yahoo.com> Content-Type: text/plain Message-Id: <1092124756.4564.61.camel@pegasus> Mime-Version: 1.0 Sender: bluez-users-admin@lists.sourceforge.net Errors-To: bluez-users-admin@lists.sourceforge.net List-Unsubscribe: , List-Id: List-Post: List-Help: List-Subscribe: , List-Archive: Date: Tue, 10 Aug 2004 09:59:16 +0200 Hi Tom, > > > > this is a Broadcom BCM2033 dongle without firmware loaded. Install the > > > > bluez-firmware package and use the bcm203x kernel driver from a recent > > > > 2.6 kernel or compile bluez-utils-2.9 with bcm203x support. > > > > > > Well, I did compile bluez-utils (and installed it) as well as bluez-firmware. > That now seems to go well. Now when I plug in the dongle I get the following > in '/var/log/messages': > Aug 9 16:00:02 xyzzy kernel: hub.c: new USB device 00:10.1-2, assigned address > 6 > Aug 9 16:00:02 xyzzy kernel: usb.c: USB device 6 (vend/prod 0xa5c/0x2033) is > not claimed by any active driver. > Aug 9 16:00:05 xyzzy /etc/hotplug/usb.agent: Setup hci_usb for USB product > a5c/2033/a0 > > But I still get the following in /proc/bus/usb/devices > >>>>> > < T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 7 Spd=12 MxCh= 0 > < D: Ver= 1.01 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 > < P: Vendor=0a5c ProdID=2033 Rev= 0.a0 > < C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=100mA > < I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) > < E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms > < E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms > < E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms > < I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) > < E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms > < E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms > < I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) > < E: Ad=83(I) Atr=01(Isoc) MxPS= 16 Ivl=1ms > < E: Ad=03(O) Atr=01(Isoc) MxPS= 16 Ivl=1ms > < I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) > < E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms > < E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms > < I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) > < E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms > < E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms > < I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) > < E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms > < E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms > < I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none) > < E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms > < E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms > < I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) > < E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms > < E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms > <<<<< > > Do I need to add something to load the firmware into the dongle?? > It appears that the ...utils... added something to the hotplug stuff for the > broadcom chipset, and it should work. Obviously it isn't. I thought this was already answered. You must use --enable-bcm203x to compile the firmware loader. After installation you will see /etc/hotplug/usb/bcm203x.usermap /etc/hotplug/usb/bcm203x in the hotplug directories. Maybe your hotplug scripts are too old and they can't work with extra entries under /etc/hotplug/usb/. Regards Marcel ------------------------------------------------------- SF.Net email is sponsored by Shop4tech.com-Lowest price on Blank Media 100pk Sonic DVD-R 4x for only $29 -100pk Sonic DVD+R for only $33 Save 50% off Retail on Ink & Toner - Free Shipping and Free Gift. http://www.shop4tech.com/z/Inkjet_Cartridges/9_108_r285 _______________________________________________ Bluez-users mailing list Bluez-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bluez-users