From: Marcel Holtmann <marcel@holtmann.org>
To: cijoml@volny.cz
Cc: BlueZ Mailing List <bluez-users@lists.sourceforge.net>
Subject: Re: [Bluez-users] 2.6.9-rc2 hibernate and BlueZ
Date: Thu, 16 Sep 2004 23:55:35 +0200 [thread overview]
Message-ID: <1095371734.19426.66.camel@pegasus> (raw)
In-Reply-To: <200409162334.37159.cijoml@volny.cz>
Hi Michal,
> after resume from hibernate, kernel oopses:
>=20
> PM: Preparing system for suspend
> Stopping tasks:=20
> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D|
> hci_usb 4-1:1.0: resume is unsafe!
> hci_usb 4-1:1.1: resume is unsafe!
> uhci_hcd 0000:00:1d.0: Unlink after no-IRQ? Different ACPI or APIC set=
tings=20
> ma
> y help.
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> hci_usb: probe of 4-1:1.2 failed with error -113
> Could not suspend device 0000:00:1d.7: error -5
> PCI: Found IRQ 10 for device 0000:00:1f.1
> PCI: Sharing IRQ 10 with 0000:00:1d.2
> PCI: Enabling device 0000:00:1f.5 (0000 -> 0003)
> PCI: Found IRQ 10 for device 0000:00:1f.5
> PCI: Sharing IRQ 10 with 0000:00:1f.3
> PCI: Sharing IRQ 10 with 0000:00:1f.6
> i810_audio: Primary codec has ID 0
> ac97_codec: AC97 Audio codec, id: CRY52 (Cirrus Logic CS4299 rev D)
> prism2_hw_init: initialized in 194 ms
> wifi0: NIC: id=3D0x800c v1.0.0
> wifi0: PRI: id=3D0x15 v1.1.1
> wifi0: STA: id=3D0x1f v1.8.0
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> hub 1-0:1.0: reactivate --> -22
> hci_usb: probe of 4-1:1.2 failed with error -113
> hub 1-0:1.0: reactivate --> -22
> hci_usb: probe of 4-1:1.2 failed with error -113
> hub 2-0:1.0: reactivate --> -22
> hci_usb: probe of 4-1:1.2 failed with error -113
> hub 3-0:1.0: reactivate --> -22
> hub 4-0:1.0: reactivate --> -22
> Restarting tasks... done
> Bluetooth: HCI USB driver ver 2.7
> hci_usb_probe: Can't set isoc interface settings
> Unable to handle kernel NULL pointer dereference at virtual address 000=
00120
> printing eip:
> cf97e842
> *pde =3D 00000000
> Oops: 0000 [#1]
> PREEMPT
> Modules linked in: hci_usb rfcomm hidp l2cap hostap_cs hostap irda crc_=
ccitt=20
> id
> e_cd cdrom bluetooth 8139too mii crc32 8250_pci 8250 serial_core i810_a=
udio=20
> ac9
> 7_codec parport_pc parport pcspkr nls_iso8859_2 ntfs rtc
> CPU: 0
> EIP: 0060:[<cf97e842>] Not tainted VLI
> EFLAGS: 00210296 (2.6.8.1)
> EIP is at hci_usb_close+0xf/0x60 [hci_usb]
> eax: c1230e80 ebx: 00000000 ecx: ced155f8 edx: c1230e90
> esi: 00000000 edi: 00000002 ebp: cf981200 esp: c7c11e3c
> ds: 007b es: 007b ss: 0068
> Process modprobe (pid: 6924, threadinfo=3Dc7c10000 task=3Dc0735aa0)
> Stack: ced3c800 c1230c80 00000000 cf97f9ff 00000000 c1230e80 cf981320 c=
1230e80
> cf981320 c02662e9 c1230e80 c1230e80 ce769050 c1230e90 cf981340 c=
023337d
> c1230e90 c1230eb8 c1230e90 c1230c80 c0266544 c1230e90 00000005 c=
f97f91a
> Call Trace:
> [<cf97f9ff>] hci_usb_disconnect+0x2f/0x94 [hci_usb]
> [<c02662e9>] usb_unbind_interface+0x7a/0x7c
> [<c023337d>] device_release_driver+0x64/0x66
> [<c0266544>] usb_driver_release_interface+0x50/0x52
> [<cf97f91a>] hci_usb_probe+0x36a/0x420 [hci_usb]
> [<c018ed7c>] init_dir+0x0/0x1f
> [<c0266262>] usb_probe_interface+0x68/0x75
> [<c02331dd>] bus_match+0x3f/0x6a
> [<c02332ef>] driver_attach+0x56/0x80
> [<c0233742>] bus_add_driver+0x91/0xaf
> [<c0233c5d>] driver_register+0x2f/0x33
> [<c011de9a>] vprintk+0x110/0x16a
> [<c026632a>] usb_register+0x3f/0x9d
> [<c011dd86>] printk+0x17/0x1b
> [<cfcd2027>] hci_usb_init+0x27/0x4d [hci_usb]
> [<c013445e>] sys_init_module+0x183/0x22f
> [<c010608b>] syscall_call+0x7/0xb
> Code: 44 24 04 08 83 44 24 08 08 83 7c 24 0c 03 0f 8e 0f ff ff ff 83 c4=
10 5b=20
> 5 e 5f 5d =
c3 83=20
> ec 0c 89 5c 24 04 89 74 24 08 8b 5c 24 10 <8b> b3 20 01 00 00 0f =
=20
> ba 73 14 02 19 c0 85 c0 74 2b 9c 58 fa ba
> <6>usb 4-1: USB disconnect, address 2
> notas:/home/cijoml/filmy/Klub Sr=E1=E8=F9#
>=20
> Maybe it is a job for you?? :)
the suspend support is somewhere on my todo list, but actually not right
now. May you wanna try it without CONFIG_BT_HCIUSB_SCO set.
Regards
Marcel
-------------------------------------------------------
This SF.Net email is sponsored by: YOU BE THE JUDGE. Be one of 170
Project Admins to receive an Apple iPod Mini FREE for your judgement on
who ports your project to Linux PPC the best. Sponsored by IBM.
Deadline: Sept. 24. Go here: http://sf.net/ppc_contest.php
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
prev parent reply other threads:[~2004-09-16 21:55 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-09-16 21:34 [Bluez-users] 2.6.9-rc2 hibernate and BlueZ Bc. Michal Semler
2004-09-16 21:55 ` Marcel Holtmann [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1095371734.19426.66.camel@pegasus \
--to=marcel@holtmann.org \
--cc=bluez-users@lists.sourceforge.net \
--cc=cijoml@volny.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox