Re: [Bluez-users] Piconet problems

jers
2005-01-14T10:21:01Z

Hi Marcel,

> Hi Jers,
>
> > hcid was not running. I've solved t=
he inconsistency but no my problem.
> >
> > Hi tried to create conne=
ction on slave1 side by
> > # hcitool cc <master_addr>
> > and so =0D
=
> > # hcitool con
> > lists me the established connection.
>
> sen=
d us the outputs of "hciconfig -a" for all of your devices. And don't =0D
=
> play with "hcitool cc". If you wanna test stuff then use l2test.
=0D
=
hci0: Type: USB
BD Address: 00:08:E0:01:9E:86 ACL MTU: 192:8 =
SCO MTU: 64:8
UP RUNNING PSCAN ISCAN
RX bytes:653 ac=
l:0 sco:0 events:19 errors:0
TX bytes:314 acl:0 sco:0 commands:=
18 errors:0
Features: 0xff 0xff 0x0b 0x00 0x00 0x00 0x00 0x00 =0D
=
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link p=
olicy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
=
Name: 'PC A'
Class: 0x3e0100
Service Classes: Netwo=
rking, Rendering, Capturing
Device Class: Computer, Uncategoriz=
ed
HCI Ver: 1.1 (0x1) HCI Rev: 0x33c LMP Ver: 1.1 (0x1) LMP Sub=
ver: 0x33c
Manufacturer: Cambridge Silicon Radio (10)

hci0=
: Type: USB
BD Address: 00:E0:98:85:A1:64 ACL MTU: 192:8 SCO=
MTU: 64:8
UP RUNNING PSCAN ISCAN
RX bytes:99 acl:0 s=
co:0 events:13 errors:0
TX bytes:296 acl:0 sco:0 commands:12 er=
rors:0
Features: 0xff 0xff 0x0f 0x00 0x00 0x00 0x00 0x00
=
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link polic=
y: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Na=
me: 'BlueZ (0)'
Class: 0x3e0100
Service Classes: Netw=
orking, Rendering, Capturing
Device Class: Computer, Uncategori=
zed
HCI Ver: 1.1 (0x1) HCI Rev: 0x175 LMP Ver: 1.1 (0x1) LMP Su=
bver: 0x175
Manufacturer: Cambridge Silicon Radio (10)

=0D
=
hci0: Type: USB
BD Address: 00:E0:98:85:A1:5F ACL MTU: 192:8 =
SCO MTU: 64:8
UP RUNNING PSCAN ISCAN
RX bytes:99 acl=
:0 sco:0 events:13 errors:0
TX bytes:296 acl:0 sco:0 commands:1=
2 errors:0
Features: 0xff 0xff 0x0f 0x00 0x00 0x00 0x00 0x00 =0D
=
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link p=
olicy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
=
Name: 'BlueZ (0)'
Class: 0x3e0100
Service Classes: =
Networking, Rendering, Capturing
Device Class: Computer, Uncate=
gorized
HCI Ver: 1.1 (0x1) HCI Rev: 0x175 LMP Ver: 1.1 (0x1) LM=
P Subver: 0x175
Manufacturer: Cambridge Silicon Radio (10)
=

> > After that, I tried to create the second connection on slave2=
side by running the same command (hcitool cc
<master_addr>) and I obta=
in the following error:
> > # Can't create connectio: input/output erro=
r.
>
> Run "hcidump -x" as root and show us the output.

HCIDump=
- HCI packet analyzer ver 1.16
device: hci0 snap_len: 1028 filter: 0xf=
fffffff

Thanks.
Regards.
Jers

>
>
>
> ---------=
----------------------------------------------
> The SF.Net email is sp=
onsored by: Beat the post-holiday blues
> Get a FREE limited edition So=
urceForge.net t-shirt from ThinkGeek.
> It's fun and FREE -- well, almo=
st....http://www.thinkgeek.com/sfshirt
> ______________________________=
_________________
> Bluez-users mailing list
> Bluez-users@lists.sour=
ceforge.net
> https://lists.sourceforge.net/lists/listinfo/bluez-users =

> =0A=0A=0A=0A________________________________________________________=
____=0ALibero ADSL: 3 mesi gratis e navighi a 1.2 Mega. E poi hai l'Adsl =
senza limiti a meno di 1 euro al giorno. =0AAbbonati subito senza costi d=
i attivazione su http://www.libero.it=0A=0A

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues
Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek.
It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt