Am Die, den 01.02.2005 schrieb Marco Trudel um 16:22:
> Sorry for sending already again an email.
> I invested another 20 minutes to the mini-howto.
> 
> It is now fully generic but should be tested with other platforms.
> 
> Marcel: tell me if it's ok or you'd like other changes...
> 
> regards
> Marco
> 
> 
> Marco Trudel wrote:
> >> looks nice so far to me, but I like to have somekind of generic cross
> >> compilation instruction.
> > 
> > 
> > unfortunately I've only an arm machine here and have no experience with 
> > other platforms.
> > maybee the guy with the axis developer board is willing to add his 
> > knowledge.
> > 
> >> I also prefer using DESTDIR for install, so
> >> that you can make an installation for /usr without overwriting your
> >> local files.
> > 
> > 
> > I made it a little bit more generic and used DESTDIR as term in the 
> > description. If someone could give feedback about the toolchain, the 
> > mini-howto would become really generic...
> > 
> > 
> > kind regards
> > Marco
> 
> 
> ______________________________________________________________________
> This document shows how to cross-compile bluez for another processor.
> 
> date/version: 01 Feb. 2005, v0.2
> author:       Marco Trudel <mtrudel@gmx.ch>
> 
> If you need help, please use the bluez-user list.
> If you have improvements or hints, do not hesitate to contact the autor.
> 
> This howto has been testet for:
> 	i686 -> arm
> 
> ------------------------------------------------------------
> 
> Ensure that the crosscompile binaries are in $PATH.
> For example, do: export PATH="$PATH:/thePathToYourCrossCompiler/bin"
> 
> Please note: The term DESTDIR will be used in the following commands.
>              This is the directory where bluez will be installed to.
> 	     Replace it, for example, with /opt/bluez or /tmp/bluez.
> 
> ########## 1. compile bluez-libs ##########
> - extract bluez-libs and change into the directory
> - configure the makefiles for cross-compiling:
>         ./configure --build=i686-pc-linux-gnu  \
>                     --host=arm-linux           \
>                     --prefix=DESTDIR           \
>                     [--sysconfdir=DESTDIR/etc]
> 
> - Explanation of the switches:
>         --build        The build platform (as example a i686).
> 	--host         The target platform (as example arm-linux).
> 	               Please change it to match your target-system.
> 	--prefix       Where bluez will be installed to.
> 	--sysconfdir   Where bluez will expect etc.
> 	               You can remove this switch if /etc is ok for you.
> 
> - Check the output. Some interesting lines:
>         checking for arm-linux-gcc... arm-linux-gcc
>         checking whether the C compiler works... yes
>         checking whether we are cross compiling... yes
> 
> - run "make", "make install"
> 
> ########## 2. compile bluez-utils ##########
> - extract bluez-utils and change into the directory
> - configure the makefiles for cross-compiling. run:
>         ./configure --build=i686-pc-linux-gnu  \
>                     --host=arm-linux           \
>                     --prefix=DESTDIR           \
>                     [--sysconfdir=DESTDIR/etc  \]
>                     LDFLAGS=-LDESTDIR/lib
> 
> - LDFLAGS is where the bluez lib will be searched for.
> (Please note that -L is needed. For example LDFLAGS=-L/opt/bluez/lib)
> 
> - run "make" and "make install"
> 
> 
> ######### 3. final steps, tests ##########
> Please note: This mini-howto assumes you have a bluetooth enabled kernel.
> If you haven't already, install it now.
> 
> Depending on your setup, you might be interested in every kb
> of diskspace to save. With -s stripping and removing of unnecessary
> files, it's possible to save ~350kb...
> 
> copy DESTDIR to your target platform.
> 
> on your target platform:
> - add "DESTDIR/lib" to /etc/ld.so.conf and, run "ldconfig"
> - run "./hcid -n" in DESTDIR/sbin
> Check the output.
> If everything works well, abort hcid and start it withhout "-n".
> 
> - "DESTDIR/bin/hcitool dev" should show you your devices
> - "DESTDIR/bin/hcitool scan" perform an inquiry scan

Hi,
somehow your usage of DESTDIR seems incorrect. With --prefix, the prefix
for programs on the target system is specified. You seem to use it for
the library path for linking as well. I have attached my version.

Regards,
Erwin