Re: [Bluez-users] problem pairing device

[Michele Puccio <michele.puccio@eng.it>]

hi marcel,
thanks for answering...but how can I "loading hci_usb with reset=1"?
my system don't the recognize bccmd as a valid command; may be I need
some extra package to install...
can you please help me? the bluetooth is the only stuff that doesn't
work in my linuxbox (dell latitude d610 + ubuntu feisty)

regards
michele


On Tue, 2007-09-25 at 00:17 +0200, Marcel Holtmann wrote:
> Hi Michele,
> 
> > I cannot pair any device using hcitool scan or hcitool inq: both exit
> > without any result or error. this is the output of hcidump during a
> > scan:
> > HCI sniffer - Bluetooth packet analyzer ver 1.33
> > device: hci0 snap_len: 1028 filter: 0xffffffff
> > HCI Command: Inquiry (0x01|0x0001) plen 5
> >         lap 0x9e8b33 len 8 num 0
> > HCI Event: Command Status (0x0f) plen 4
> >         Inquiry (0x01|0x0001) status 0x00 ncmd 1
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Vendor (0xff) plen 7
> >         0000: cd 03 00 04 00 0000                              .......
> > HCI Event: Inquiry Complete (0x01) plen 1
> >         
> > status 0x00 and this is the output of hciconfig -a
> > hci0:   Type: USB
> >         BD Address: 00:16:41:1B:97:A3 ACL MTU: 384:8 SCO MTU: 64:8
> >         UP RUNNING PSCAN 
> >         RX bytes:807 acl:0 sco:0 events:63 errors:0
> >         TX bytes:331 acl:0 sco:0 commands:20 errors:0
> >         Features: 0xff 0xff 0x9f 0xfe 0x9b 0xf9 0x00 0x80
> >         Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 
> >         Link policy: RSWITCH HOLD SNIFF PARK 
> >         Link mode: SLAVE ACCEPT 
> >         Name: 'D610'
> >         Class: 0x000100
> >         Service Classes: Unspecified
> >         Device Class: Computer, Uncategorized
> >         HCI Ver: 1.2 (0x2) HCI Rev: 0x679 LMP Ver: 1.2 (0x2) LMP Subver:
> > 0x679
> >         Manufacturer: Cambridge Silicon Radio (10)
> 
> this is one of the funny Dell adapters with the vendor messages. No idea
> what this is actually doing. However maybe loading hci_usb with reset=1
> might help.
> 
> Also you can check "sudo bccmd buildname" if this is a special firmware.
> 
> Regards
> 
> Marcel
> 
> 
> 


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users