Linux bluetooth development
 help / color / mirror / Atom feed
From: Amitkumar Karwar <akarwar@marvell.com>
To: <linux-bluetooth@vger.kernel.org>
Cc: Nishant Sarmukadam <nishants@marvell.com>, <wnhuang@chromium.com>,
	<devicetree@vger.kernel.org>, Cathy Luo <cluo@marvell.com>,
	<linux-kernel@vger.kernel.org>, Xinming Hu <huxm@marvell.com>,
	Amitkumar Karwar <akarwar@marvell.com>
Subject: [PATCH v4 3/3] mwifiex: parse host wakeup configuration from device
Date: Tue, 16 Feb 2016 01:14:39 -0800	[thread overview]
Message-ID: <1455614079-4263-3-git-send-email-akarwar@marvell.com> (raw)
In-Reply-To: <1455614079-4263-1-git-send-email-akarwar@marvell.com>

From: Xinming Hu <huxm@marvell.com>

This patch implement a framework for board specific wakeup.
driver parse irq/gpio number from device tree, corresponding
resources will be allocated, and used for host suspend/resume.
driver private binding file is also updated in the patch.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
---
v4: Replaced #ifdef with __maybe_unused(Arnd Bergmann)
---
 .../bindings/net/wireless/marvell-sd8xxx.txt       | 10 +++
 .../net/wireless/marvell/mwifiex/platform_drv.c    | 91 ++++++++++++++++++++++
 2 files changed, 101 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
index c337fab..50138fd 100644
--- a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
+++ b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt
@@ -14,6 +14,11 @@ Optional properties:
   - marvell,wakeup-gpios : Chip's wakeup gpio pin number. This needs to be downloaded
 			to to firmware. Chip notifies wifi wakeup signal to SOC
 			through this pin.
+  - interrupt-parent: phandle of the parent interrupt controller
+  - interrupts : interrupt number to the cpu
+  - gpios: specify SOC's wakeup GPIO
+  - pinctrl-names : a pinctrl state named "default" must be defined
+  - pinctrl-0 : pin control group to be used for this controller
 
 Example:
 
@@ -27,5 +32,10 @@ wlan {
 	marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 <
 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01 ...>;
 	marvell,wakeup-gpios = <3>;
+	interrupt-parent = <&pio>;
+	interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
+	gpios = <&pio 38 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&wake_pins>;
 };
 
diff --git a/drivers/net/wireless/marvell/mwifiex/platform_drv.c b/drivers/net/wireless/marvell/mwifiex/platform_drv.c
index 5fd5d80..5ae7dc0 100644
--- a/drivers/net/wireless/marvell/mwifiex/platform_drv.c
+++ b/drivers/net/wireless/marvell/mwifiex/platform_drv.c
@@ -18,9 +18,63 @@
 
 struct platform_device *mwifiex_plt_dev;
 
+struct mwifiex_wake_dev {
+	struct device *dev;
+	int irq_wifi;
+	bool wake_by_wifi;
+};
+
+static irqreturn_t mwifiex_wake_irq_wifi(int irq, void *priv)
+{
+	struct mwifiex_wake_dev *ctx = priv;
+
+	if (ctx->irq_wifi >= 0) {
+		ctx->wake_by_wifi = true;
+		disable_irq_nosync(ctx->irq_wifi);
+	}
+
+	return IRQ_HANDLED;
+}
+
 static int mwifiex_plt_probe(struct platform_device *pdev)
 {
+	int ret;
+	struct mwifiex_wake_dev *ctx;
+	int gpio;
+
 	mwifiex_plt_dev = pdev;
+
+	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	ctx->dev = &pdev->dev;
+	ctx->irq_wifi = platform_get_irq(pdev, 0);
+	if (ctx->irq_wifi < 0)
+		dev_err(&pdev->dev, "Failed to get irq_wifi\n");
+
+	gpio = of_get_gpio(pdev->dev.of_node, 0);
+	if (gpio_is_valid(gpio))
+		gpio_direction_input(gpio);
+	else
+		dev_err(&pdev->dev, "gpio wifi is invalid\n");
+
+	if (ctx->irq_wifi >= 0) {
+		ret = devm_request_irq(&pdev->dev, ctx->irq_wifi,
+				       mwifiex_wake_irq_wifi,
+				       IRQF_TRIGGER_LOW,
+				       "wifi_wake", ctx);
+		if (ret) {
+			dev_err(&pdev->dev,
+				"Failed to request irq_wifi %d (%d)\n",
+				ctx->irq_wifi, ret);
+			return -EINVAL;
+		}
+		disable_irq(ctx->irq_wifi);
+	}
+
+	platform_set_drvdata(pdev, ctx);
+
 	return 0;
 }
 
@@ -30,6 +84,42 @@ static int mwifiex_plt_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static int __maybe_unused mwifiex_plt_suspend(struct device *dev)
+{
+	struct mwifiex_wake_dev *ctx = dev_get_drvdata(dev);
+	int ret;
+
+	if (ctx->irq_wifi >= 0) {
+		ctx->wake_by_wifi = false;
+		enable_irq(ctx->irq_wifi);
+		ret = enable_irq_wake(ctx->irq_wifi);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int __maybe_unused mwifiex_plt_resume(struct device *dev)
+{
+	struct mwifiex_wake_dev *ctx = dev_get_drvdata(dev);
+	int ret;
+
+	if (ctx->irq_wifi >= 0) {
+		ret = disable_irq_wake(ctx->irq_wifi);
+		if (!ctx->wake_by_wifi)
+			disable_irq(ctx->irq_wifi);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static const struct dev_pm_ops mwifiex_plt_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(mwifiex_plt_suspend, mwifiex_plt_resume)
+};
+
 static const struct of_device_id mwifiex_dt_match[] = {
 	{
 		.compatible = "marvell,sd8xxx",
@@ -45,6 +135,7 @@ static struct platform_driver mwifiex_platform_driver = {
 	.driver = {
 		.name	= "mwifiex_plt",
 		.of_match_table = mwifiex_dt_match,
+		.pm = &mwifiex_plt_pm_ops,
 	}
 };
 
-- 
1.8.1.4

  parent reply	other threads:[~2016-02-16  9:14 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-02-16  9:14 [PATCH v4 1/3] mwifiex: register platform specific driver Amitkumar Karwar
2016-02-16  9:14 ` [PATCH v4 2/3] mwifiex: parse chip specific gpio from device tree Amitkumar Karwar
2016-02-18 14:37   ` Rob Herring
2016-02-16  9:14 ` Amitkumar Karwar [this message]
2016-02-18 14:37   ` [PATCH v4 3/3] mwifiex: parse host wakeup configuration from device Rob Herring
2016-02-16 11:28 ` [PATCH v4 1/3] mwifiex: register platform specific driver Arnd Bergmann
2016-02-18 14:38 ` Rob Herring
2016-02-29 14:04   ` Amitkumar Karwar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1455614079-4263-3-git-send-email-akarwar@marvell.com \
    --to=akarwar@marvell.com \
    --cc=cluo@marvell.com \
    --cc=devicetree@vger.kernel.org \
    --cc=huxm@marvell.com \
    --cc=linux-bluetooth@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nishants@marvell.com \
    --cc=wnhuang@chromium.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox