From: Balakrishna Godavarthi <bgodavar@codeaurora.org>
To: marcel@holtmann.org, johan.hedberg@gmail.com
Cc: mka@chromium.org, linux-kernel@vger.kernel.org,
linux-bluetooth@vger.kernel.org, hemantg@codeaurora.org,
linux-arm-msm@vger.kernel.org, bgodavar@codeaurora.org,
abhishekpandit@chromium.org, seanpaul@chromium.org,
gubbaven@codeaurora.org, rjliao@codeaurora.org
Subject: [Resend v1] Bluetooth: hci_qca: Enhance retry logic in qca_setup
Date: Wed, 11 Nov 2020 10:44:13 +0530 [thread overview]
Message-ID: <1605071653-5088-1-git-send-email-bgodavar@codeaurora.org> (raw)
Currently driver only retries to download FW if FW downloading
is failed. Sometimes observed command timeout for version request
command, if this happen on some platforms during boot time, then
a reboot is needed to turn ON BT. Instead to avoid a reboot, now
extended retry logic for version request command too.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
---
drivers/bluetooth/hci_qca.c | 34 ++++++++++++++++++----------------
1 file changed, 18 insertions(+), 16 deletions(-)
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 2d3f1f1..1c9a2d46 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -1672,7 +1672,7 @@ static int qca_setup(struct hci_uart *hu)
retry:
ret = qca_power_on(hdev);
if (ret)
- return ret;
+ goto out;
clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
@@ -1681,7 +1681,7 @@ static int qca_setup(struct hci_uart *hu)
ret = qca_read_soc_version(hdev, &soc_ver, soc_type);
if (ret)
- return ret;
+ goto out;
} else {
qca_set_speed(hu, QCA_INIT_SPEED);
}
@@ -1691,7 +1691,7 @@ static int qca_setup(struct hci_uart *hu)
if (speed) {
ret = qca_set_speed(hu, QCA_OPER_SPEED);
if (ret)
- return ret;
+ goto out;
qca_baudrate = qca_get_baudrate_value(speed);
}
@@ -1700,7 +1700,7 @@ static int qca_setup(struct hci_uart *hu)
/* Get QCA version information */
ret = qca_read_soc_version(hdev, &soc_ver, soc_type);
if (ret)
- return ret;
+ goto out;
}
bt_dev_info(hdev, "QCA controller version 0x%08x", soc_ver);
@@ -1721,20 +1721,22 @@ static int qca_setup(struct hci_uart *hu)
* patch/nvm-config is found, so run with original fw/config.
*/
ret = 0;
- } else {
- if (retries < MAX_INIT_RETRIES) {
- qca_power_shutdown(hu);
- if (hu->serdev) {
- serdev_device_close(hu->serdev);
- ret = serdev_device_open(hu->serdev);
- if (ret) {
- bt_dev_err(hdev, "failed to open port");
- return ret;
- }
+ }
+
+out:
+ if (ret && retries < MAX_INIT_RETRIES) {
+ bt_dev_warn(hdev, "Retry BT power ON:%d", retries);
+ qca_power_shutdown(hu);
+ if (hu->serdev) {
+ serdev_device_close(hu->serdev);
+ ret = serdev_device_open(hu->serdev);
+ if (ret) {
+ bt_dev_err(hdev, "failed to open port");
+ return ret;
}
- retries++;
- goto retry;
}
+ retries++;
+ goto retry;
}
/* Setup bdaddr */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
next reply other threads:[~2020-11-11 5:15 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-11 5:14 Balakrishna Godavarthi [this message]
2020-11-11 9:53 ` [Resend v1] Bluetooth: hci_qca: Enhance retry logic in qca_setup Marcel Holtmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1605071653-5088-1-git-send-email-bgodavar@codeaurora.org \
--to=bgodavar@codeaurora.org \
--cc=abhishekpandit@chromium.org \
--cc=gubbaven@codeaurora.org \
--cc=hemantg@codeaurora.org \
--cc=johan.hedberg@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-bluetooth@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marcel@holtmann.org \
--cc=mka@chromium.org \
--cc=rjliao@codeaurora.org \
--cc=seanpaul@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox