From: Vikram Kandukuri <vkandukuri@atheros.com>
To: "linux-bluetooth@vger.kernel.org" <linux-bluetooth@vger.kernel.org>
Cc: <marcel@holtmann.org>
Subject: Re: [PATCH] Added support for Atheros AR300x UART Bluetooth Chip
Date: Wed, 17 Feb 2010 15:25:45 +0530 [thread overview]
Message-ID: <20100217095542.GB2138@ATH-LT-538> (raw)
In-Reply-To: <20100209114231.GA6587@ATH-LT-538>
Hi Marcel,
Please send your comments
Thanks
>
> Signed-off-by: Suraj <suraj@atheros.com>
>
> ---
> drivers/bluetooth/Kconfig | 10 +
> drivers/bluetooth/Makefile | 1 +
> drivers/bluetooth/hci_ath.c | 545 +++++++++++++++++++++++++++++++++++++++++
> drivers/bluetooth/hci_ath.h | 72 ++++++
> drivers/bluetooth/hci_ldisc.c | 6 +
> drivers/bluetooth/hci_uart.h | 8 +-
> 6 files changed, 641 insertions(+), 1 deletions(-)
> create mode 100755 drivers/bluetooth/hci_ath.c
> create mode 100755 drivers/bluetooth/hci_ath.h
>
> diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> index 058fbcc..32b98a4 100644
> --- a/drivers/bluetooth/Kconfig
> +++ b/drivers/bluetooth/Kconfig
> @@ -58,6 +58,16 @@ config BT_HCIUART_BCSP
>
> Say Y here to compile support for HCI BCSP protocol.
>
> +config BT_HCIUART_ATH
> + bool "Atheros AR3001 Board support"
> + depends on BT_HCIUART
> + help
> + HCIATH (HCI Atheros) is a serial protocol for communication
> + between Bluetooth device and host. This protocol is required for
> + serial Bluetooth devices that are based on Atheros AR3001 chips.
> +
> + Say Y here to compile support for HCIATH protocol.
> +
> config BT_HCIUART_LL
> bool "HCILL protocol support"
> depends on BT_HCIUART
> diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> index 7e5aed5..1481faa 100644
> --- a/drivers/bluetooth/Makefile
> +++ b/drivers/bluetooth/Makefile
> @@ -26,4 +26,5 @@ hci_uart-y := hci_ldisc.o
> hci_uart-$(CONFIG_BT_HCIUART_H4) += hci_h4.o
> hci_uart-$(CONFIG_BT_HCIUART_BCSP) += hci_bcsp.o
> hci_uart-$(CONFIG_BT_HCIUART_LL) += hci_ll.o
> +hci_uart-$(CONFIG_BT_HCIUART_ATH) += hci_ath.o
> hci_uart-objs := $(hci_uart-y)
> diff --git a/drivers/bluetooth/hci_ath.c b/drivers/bluetooth/hci_ath.c
> new file mode 100755
> index 0000000..abacc09
> --- /dev/null
> +++ b/drivers/bluetooth/hci_ath.c
> @@ -0,0 +1,545 @@
> +/*
> + * Copyright (c) 2009-2010 Atheros Communications Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> + *
> + */
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +
> +#include <linux/init.h>
> +#include <linux/sched.h>
> +#include <linux/types.h>
> +#include <linux/fcntl.h>
> +#include <linux/interrupt.h>
> +#include <linux/ptrace.h>
> +#include <linux/poll.h>
> +
> +#include <linux/slab.h>
> +#include <linux/tty.h>
> +#include <linux/errno.h>
> +#include <linux/string.h>
> +#include <linux/signal.h>
> +#include <linux/ioctl.h>
> +#include <linux/skbuff.h>
> +#include <linux/firmware.h>
> +#include <linux/wait.h>
> +#include <linux/timer.h>
> +#include <linux/tty.h>
> +
> +#include <net/bluetooth/bluetooth.h>
> +#include <net/bluetooth/hci.h>
> +
> +#include "hci_uart.h"
> +#include "hci_ath.h"
> +static void ath_context_switch(struct work_struct *work)
> +{
> + int status;
> + struct ath_struct *ath;
> + struct hci_uart *hu;
> + struct tty_struct *tty;
> + struct sk_buff *skbuf;
> + ath = container_of(work, struct ath_struct, ctxtsw);
> + hu = ath->hu;
> + tty = hu->tty;
> + status = ath_wakeup_ar3001(tty);
> + if ((status & TIOCM_CTS)) {
> + while ((skbuf = skb_dequeue(&ath->tx_wait_q)))
> + skb_queue_tail(&ath->txq, skbuf);
> +
> + /* Ready to send Data */
> + clear_bit(HCI_UART_SENDING, &hu->tx_state);
> + hci_uart_tx_wakeup(hu);
> + }
> +}
> +
> +/* Initialize protocol */
> +static int ath_open(struct hci_uart *hu)
> +{
> + struct ath_struct *ath;
> + BT_DBG("hu %p", hu);
> + ath = kzalloc(sizeof(*ath), GFP_ATOMIC);
> + if (!ath)
> + return -ENOMEM;
> + skb_queue_head_init(&ath->txq);
> + skb_queue_head_init(&ath->tx_wait_q);
> + skb_queue_head_init(&ath->tx_cmd_wait_q);
> + spin_lock_init(&ath->hciath_lock);
> + ath->cur_sleep = 0;
> + ath->num_cmds_complete = 1;
> + hu->priv = ath;
> + ath->hu = hu;
> + init_waitqueue_head(&ath->wqevt);
> + INIT_WORK(&ath->ctxtsw, ath_context_switch);
> + return 0;
> +}
> +
> +/* Flush protocol data */
> +static int ath_flush(struct hci_uart *hu)
> +{
> + struct ath_struct *ath = hu->priv;
> + BT_DBG("hu %p", hu);
> + skb_queue_purge(&ath->tx_wait_q);
> + skb_queue_purge(&ath->txq);
> + skb_queue_purge(&ath->tx_cmd_wait_q);
> + return 0;
> +}
> +
> +/* Close protocol */
> +static int ath_close(struct hci_uart *hu)
> +{
> + struct ath_struct *ath;
> + ath = hu->priv;
> + BT_DBG("hu %p", hu);
> + skb_queue_purge(&ath->tx_wait_q);
> + skb_queue_purge(&ath->txq);
> + skb_queue_purge(&ath->tx_cmd_wait_q);
> + if (ath->rx_skb)
> + kfree_skb(ath->rx_skb);
> + wake_up_interruptible(&ath->wqevt);
> + hu->priv = NULL;
> + kfree(ath);
> + return 0;
> +}
> +
> +/* Enqueue frame for transmittion (padding, crc, etc) */
> +/* may be called from two simultaneous tasklets */
> +static int ath_enqueue(struct hci_uart *hu, struct sk_buff *skb)
> +{
> + struct ath_struct *ath;
> + ath = hu->priv;
> + if (HCI_SCODATA_PKT == bt_cb(skb)->pkt_type) {
> +
> + /* Discard SCO packet as AR3001 does not support SCO over HCI */
> + BT_DBG("SCO Packet over HCI received Dropping\n");
> + kfree(skb);
> + return 0;
> + }
> + BT_DBG("hu %p skb %p", hu, skb);
> +
> + /* Prepend skb with frame type */
> + memcpy(skb_push(skb, 1), &bt_cb(skb)->pkt_type, 1);
> + if (ath->num_cmds_complete <= 0
> + && HCI_COMMAND_PKT == bt_cb(skb)->pkt_type) {
> + skb_queue_tail(&ath->tx_cmd_wait_q, skb);
> + return 0;
> + }
> +
> + skb_queue_tail(&ath->txq, skb);
> + set_bit(HCI_UART_SENDING, &hu->tx_state);
> +
> + schedule_work(&ath->ctxtsw);
> + return 0;
> +}
> +
> +static struct sk_buff *ath_dequeue(struct hci_uart *hu)
> +{
> + struct ath_struct *ath;
> + struct sk_buff *skbuff;
> + ath = hu->priv;
> + skbuff = skb_dequeue(&ath->txq);
> + if (NULL != skbuff) {
> + ath_handle_host_data(ath, bt_cb(skbuff)->pkt_type,
> + &skbuff->data[1], skbuff->len - 1);
> + }
> + return skbuff;
> +}
> +
> +static inline int ath_check_data_len(struct ath_struct *ath, int len)
> +{
> + register int room = skb_tailroom(ath->rx_skb);
> + BT_DBG("len %d room %d", len, room);
> + if (!len) {
> + hci_recv_frame(ath->rx_skb);
> + } else if (len > room) {
> + BT_ERR("Data length is too large");
> + kfree_skb(ath->rx_skb);
> + } else {
> + ath->rx_state = HCIATH_W4_DATA;
> + ath->rx_count = len;
> + return len;
> + }
> + ath->rx_state = HCIATH_W4_PACKET_TYPE;
> + ath->rx_skb = NULL;
> + ath->rx_count = 0;
> + return 0;
> +}
> +
> +/* Recv data */
> +static int ath_recv(struct hci_uart *hu, void *data, int count)
> +{
> + struct ath_struct *ath = hu->priv;
> + register char *ptr;
> + struct hci_event_hdr *eh;
> + struct hci_acl_hdr *ah;
> + struct hci_sco_hdr *sh;
> + struct sk_buff *skbuff;
> + register int len, type, dlen;
> + skbuff = NULL;
> + BT_DBG("hu %p count %d rx_state %d rx_count %d", hu, count,
> + ath->rx_state, ath->rx_count);
> + ptr = data;
> + while (count) {
> + if (ath->rx_count) {
> + len = min_t(unsigned int, ath->rx_count, count);
> + memcpy(skb_put(ath->rx_skb, len), ptr, len);
> + ath->rx_count -= len;
> + count -= len;
> + ptr += len;
> + if (ath->rx_count)
> + continue;
> + switch (ath->rx_state) {
> + case HCIATH_W4_DATA:
> + ath_handle_data_from_controller(ath,
> + bt_cb
> + (ath->rx_skb)->
> + pkt_type,
> + ath->rx_skb->
> + data,
> + ath->rx_skb->
> + len);
> + if (HCI_EVENT_PKT ==
> + bt_cb(ath->rx_skb)->pkt_type
> + && ath->num_cmds_complete > 0) {
> +
> + skbuff =
> + skb_dequeue(&ath->tx_cmd_wait_q);
> + if (skbuff != NULL) {
> + skb_queue_tail(&ath->txq,
> + skbuff);
> + schedule_work(&ath->ctxtsw);
> + }
> + }
> + if (ath_verify_event_discardable
> + (hu, bt_cb(ath->rx_skb)->pkt_type,
> + ath->rx_skb->data)) {
> + kfree(ath->rx_skb);
> + ath->rx_skb = NULL;
> + } else {
> + hci_recv_frame(ath->rx_skb);
> + }
> + ath->rx_state = HCIATH_W4_PACKET_TYPE;
> + ath->rx_skb = NULL;
> + ath->rx_count = 0;
> + continue;
> + case HCIATH_W4_EVENT_HDR:
> + eh = (struct hci_event_hdr *)ath->rx_skb->data;
> + BT_DBG("Event header: evt 0x%2.2x plen %d",
> + eh->evt, eh->plen);
> + ath_check_data_len(ath, eh->plen);
> + continue;
> + case HCIATH_W4_ACL_HDR:
> + ah = (struct hci_acl_hdr *)ath->rx_skb->data;
> + dlen = __le16_to_cpu(ah->dlen);
> + BT_DBG("ACL header: dlen %d", dlen);
> + ath_check_data_len(ath, dlen);
> + continue;
> + case HCIATH_W4_SCO_HDR:
> + sh = (struct hci_sco_hdr *)ath->rx_skb->data;
> + BT_DBG("SCO header: dlen %d", sh->dlen);
> + ath_check_data_len(ath, sh->dlen);
> + continue;
> + }
> + }
> +
> + /* HCIATH_W4_PACKET_TYPE */
> + switch (*ptr) {
> + case HCI_EVENT_PKT:
> + BT_DBG("Event packet");
> + ath->rx_state = HCIATH_W4_EVENT_HDR;
> + ath->rx_count = HCI_EVENT_HDR_SIZE;
> + type = HCI_EVENT_PKT;
> + break;
> + case HCI_ACLDATA_PKT:
> + BT_DBG("ACL packet");
> + ath->rx_state = HCIATH_W4_ACL_HDR;
> + ath->rx_count = HCI_ACL_HDR_SIZE;
> + type = HCI_ACLDATA_PKT;
> + break;
> + case HCI_SCODATA_PKT:
> + BT_DBG("SCO packet");
> + ath->rx_state = HCIATH_W4_SCO_HDR;
> + ath->rx_count = HCI_SCO_HDR_SIZE;
> + type = HCI_SCODATA_PKT;
> + break;
> + default:
> + BT_ERR("Unknown HCI packet type %2.2x", (__u8) *ptr);
> + hu->hdev->stat.err_rx++;
> + ptr++;
> + count--;
> + continue;
> + };
> + ptr++;
> + count--;
> +
> + /* Allocate packet */
> + ath->rx_skb = bt_skb_alloc(HCI_MAX_FRAME_SIZE, GFP_ATOMIC);
> + if (!ath->rx_skb) {
> + BT_ERR("Can't allocate mem for new packet");
> + ath->rx_state = HCIATH_W4_PACKET_TYPE;
> + ath->rx_count = 0;
> + return 0;
> + }
> + ath->rx_skb->dev = (void *)hu->hdev;
> + bt_cb(ath->rx_skb)->pkt_type = type;
> + } return count;
> +}
> +
> +static void ath_controller_sleep_mode(struct hci_uart *hu, bool enable)
> +{
> + unsigned char sleepcmd[] = { 0x01, 0x04, 0xFC, 0x01, 0x00 };
> + sleepcmd[4] = enable;
> + ath_write_data_to_cntrlr(hu->hdev, sleepcmd, sizeof(sleepcmd));
> +}
> +
> +int ath_wakeup_ar3001(struct tty_struct *tty)
> +{
> + struct termios settings;
> + int status = 0x00;
> + mm_segment_t oldfs;
> + status = tty->driver->ops->tiocmget(tty, NULL);
> +
> + if ((status & TIOCM_CTS))
> + return status;
> +
> + oldfs = get_fs();
> + set_fs(KERNEL_DS);
> + n_tty_ioctl_helper(tty, NULL, TCGETS, (unsigned long)&settings);
> +
> + settings.c_cflag &= ~CRTSCTS;
> + n_tty_ioctl_helper(tty, NULL, TCSETS, (unsigned long)&settings);
> + set_fs(oldfs);
> + status = tty->driver->ops->tiocmget(tty, NULL);
> +
> + tty->driver->ops->tiocmset(tty, NULL, 0x00, TIOCM_RTS);
> + mdelay(20);
> +
> + status = tty->driver->ops->tiocmget(tty, NULL);
> +
> + tty->driver->ops->tiocmset(tty, NULL, TIOCM_RTS, 0x00);
> + mdelay(20);
> +
> + status = tty->driver->ops->tiocmget(tty, NULL);
> + oldfs = get_fs();
> + set_fs(KERNEL_DS);
> + n_tty_ioctl_helper(tty, NULL, TCGETS, (unsigned long)&settings);
> +
> + settings.c_cflag |= CRTSCTS;
> + n_tty_ioctl_helper(tty, NULL, TCSETS, (unsigned long)&settings);
> + set_fs(oldfs);
> + return status;
> +}
> +
> +int ath_fullboot_config(struct hci_uart *hu, int current_event)
> +{
> + struct sk_buff *skbuf;
> + struct ath_struct *ath = hu->priv;
> + static int autosleep;
> + unsigned char rstevt[] = { 0x1, 0x3, 0xc, 0x0 };
> + if (current_event == HCI_RESET) {
> +
> + if (ath->cur_sleep) {
> + autosleep = 1;
> + ath_controller_sleep_mode(hu, 1);
> + return 1;
> + } else {
> + return 0;
> + }
> + }
> +
> + if (current_event == HCI_SET_SLEEP_MODE) {
> +
> + if (autosleep == 0)
> + return 1;
> +
> + while ((skbuf = skb_dequeue(&ath->tx_wait_q)))
> + skb_queue_tail(&ath->txq, skbuf);
> +
> + ath_write_data_to_host(hu->hdev, rstevt, sizeof(rstevt));
> + autosleep = 0;
> + return 1;
> + }
> + return 0;
> +}
> +
> +int ath_write_data_to_host(void *dev, unsigned char *data, u8 length)
> +{
> + struct sk_buff *skbuf;
> + struct hci_dev *hdev;
> + hdev = (struct hci_dev *)dev;
> + skbuf = bt_skb_alloc(length, GFP_ATOMIC);
> + if (!skbuf) {
> + BT_ERR("Memory allocation failed");
> + return -1;
> + }
> + skb_orphan(skbuf);
> +
> + /* First byte will be added as packet type */
> + bt_cb(skbuf)->pkt_type = data[0];
> + skbuf->dev = (void *)hdev;
> + memcpy(skb_put(skbuf, length - 1), &data[1], length - 1);
> + hci_recv_frame(skbuf);
> + return length;
> +}
> +
> +int ath_write_data_to_cntrlr(void *dev, unsigned char *Data, u8 len)
> +{
> + struct sk_buff *skbuff;
> + struct ath_struct *ath;
> + struct hci_uart *hu;
> + struct hci_dev *hdev;
> + if (NULL == dev) {
> + BT_DBG("NULL handle received %p \n", dev);
> + return 0;
> + }
> + hdev = (struct hci_dev *)dev;
> + hu = (struct hci_uart *)hdev->driver_data;
> + if (hu == NULL) {
> + BT_DBG("NULL handle received %p \n", hdev);
> + return 0;
> + }
> + ath = hu->priv;
> + if (ath == NULL) {
> + BT_DBG("NULL handle received \n");
> + return 0;
> + }
> + skbuff = bt_skb_alloc(len, GFP_ATOMIC);
> + if (skbuff == NULL) {
> + BT_DBG("Malloc Fail memory %p \n", skbuff);
> + return 0;
> + }
> + skb_orphan(skbuff);
> +
> + if (len != 0)
> + memcpy(skb_put(skbuff, len), Data, len);
> +
> + bt_cb(skbuff)->pkt_type = HCI_COMMAND_PKT;
> + skbuff->dev = dev;
> + if (ath->num_cmds_complete > 0) {
> + skb_queue_tail(&ath->txq, skbuff);
> + schedule_work(&ath->ctxtsw);
> + } else {
> + skb_queue_tail(&ath->tx_cmd_wait_q, skbuff);
> + }
> + return len;
> +}
> +
> +int ath_check_sleep_cmd(struct ath_struct *ath, unsigned char *packet)
> +{
> + if (packet[0] == HCI_EVENT_PKT && packet[1] == 0xFC)
> + ath->cur_sleep = packet[3];
> +
> + return 0;
> +}
> +
> +int ath_verify_event_discardable(struct hci_uart *hu, unsigned char pkt_type,
> + unsigned char *packet)
> +{
> + if (pkt_type != HCI_EVENT_PKT)
> + return 0;
> +
> + switch (packet[0]) {
> + case 0x0E: /* Command Complete Event */
> + if (packet[3] == 0x03 && packet[4] == 0x0C) {
> +
> + /* Command complete for HCI Reset Received */
> + return ath_fullboot_config(hu, HCI_RESET);
> + } else if (packet[3] == 0x04 && packet[4] == 0xFC) {
> + return ath_fullboot_config(hu, HCI_SET_SLEEP_MODE);
> + }
> + break;
> + }
> + return 0;
> +}
> +
> +/* Update the number of commands that can be sent to controller */
> +void ath_handle_hci_cmd(struct ath_struct *ath, u8 * packet)
> +{
> + spin_lock(&ath->hciath_lock);
> + ath->num_cmds_complete--;
> + spin_unlock(&ath->hciath_lock);
> +}
> +
> +void ath_handle_hci_event(struct ath_struct *ath, u8 * packet)
> +{
> + switch (packet[0]) {
> + case 0x05: /* ACL Disconnection Complete Event */
> + break;
> + case 0x03: /* ACL Connection Complete Event */
> + break;
> + case 0x0E: /* Command Complete Event */
> + spin_lock(&ath->hciath_lock);
> + ath->num_cmds_complete = packet[2];
> + spin_unlock(&ath->hciath_lock);
> + break;
> + case 0x0F: /* Command Status Event */
> + spin_lock(&ath->hciath_lock);
> + ath->num_cmds_complete = packet[3];
> + spin_unlock(&ath->hciath_lock);
> + break;
> + }
> +}
> +
> +void ath_handle_host_data(struct ath_struct *ath, u8 pktType, u8 * packet,
> + unsigned int len)
> +{
> + switch (pktType) {
> + case HCI_ACLDATA_PKT: /* ACL packets */
> + break;
> + case HCI_COMMAND_PKT: /* HCI Commands */
> + ath_handle_hci_cmd(ath, packet);
> + ath_check_sleep_cmd(ath, packet);
> + break;
> + }
> +}
> +
> +void ath_handle_data_from_controller(struct ath_struct *ath, u8 pktType,
> + u8 *packet, unsigned int len)
> +{
> + switch (pktType) {
> + case HCI_ACLDATA_PKT: /* ACL packets */
> + break;
> + case HCI_EVENT_PKT: /* HCI Events */
> + ath_handle_hci_event(ath, packet);
> + break;
> + }
> +}
> +
> +static struct hci_uart_proto athp = {
> + .id = HCI_UART_ATH,
> + .open = ath_open,
> + .close = ath_close,
> + .recv = ath_recv,
> + .enqueue = ath_enqueue,
> + .dequeue = ath_dequeue,
> + .flush = ath_flush,
> +};
> +
> +int ath_init(void)
> +{
> + int err = hci_uart_register_proto(&athp);
> + if (!err)
> + BT_INFO("HCIATH protocol initialized");
> +
> + else
> + BT_ERR("HCIATH protocol registration failed");
> + return err;
> +}
> +
> +int ath_deinit(void)
> +{
> + return hci_uart_unregister_proto(&athp);
> +}
> diff --git a/drivers/bluetooth/hci_ath.h b/drivers/bluetooth/hci_ath.h
> new file mode 100755
> index 0000000..7513a89
> --- /dev/null
> +++ b/drivers/bluetooth/hci_ath.h
> @@ -0,0 +1,72 @@
> +/*
> + * Copyright (c) 2009-2010 Atheros Communications Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> + *
> + */
> +
> +#ifndef __HCI_ATH_H_
> +#define __HCI_ATH_H_
> +
> +#include <linux/fs.h>
> +#include <linux/errno.h>
> +#include <linux/string.h>
> +#include <linux/signal.h>
> +#include <linux/timer.h>
> +
> +#include <linux/ioctl.h>
> +#include <linux/skbuff.h>
> +#include <linux/firmware.h>
> +#include <linux/wait.h>
> +
> +#include <net/bluetooth/bluetooth.h>
> +#include <net/bluetooth/hci_core.h>
> +
> +/* HCIATH receiver States */
> +#define HCIATH_W4_PACKET_TYPE 0
> +#define HCIATH_W4_EVENT_HDR 1
> +#define HCIATH_W4_ACL_HDR 2
> +#define HCIATH_W4_SCO_HDR 3
> +#define HCIATH_W4_DATA 4
> +
> +#define HCI_SET_SLEEP_MODE 0xFC04
> +#define HCI_RESET 0x030C
> + struct ath_struct {
> + struct hci_uart *hu;
> + unsigned int rx_state;
> + unsigned int rx_count;
> + unsigned int cur_sleep;
> + int num_cmds_complete;
> + spinlock_t hciath_lock;
> + struct sk_buff *rx_skb;
> + struct sk_buff_head txq;
> + struct sk_buff_head tx_wait_q;
> + struct sk_buff_head tx_cmd_wait_q;
> + wait_queue_head_t wqevt;
> + struct work_struct ctxtsw;
> +};
> +int ath_write_data_to_cntrlr(void *dev, unsigned char *Data, u8 len);
> +int ath_write_data_to_host(void *dev, unsigned char *data, u8 length);
> +int ath_wakeup_ar3001(struct tty_struct *tty);
> +int ath_verify_event_discardable(struct hci_uart *hu, unsigned char pkt_type,
> + unsigned char *packet);
> +int ath_check_sleep_cmd(struct ath_struct *ath, unsigned char *packet);
> +void ath_handle_host_data(struct ath_struct *ath, u8 pktType, u8 *packet,
> + unsigned int len);
> +void ath_handle_data_from_controller(struct ath_struct *ath, u8 pktType,
> + u8 *packet, unsigned int len);
> +
> +
> +#endif /* __HCI_ATH_H_ */
> diff --git a/drivers/bluetooth/hci_ldisc.c b/drivers/bluetooth/hci_ldisc.c
> index aa09193..bd16130 100644
> --- a/drivers/bluetooth/hci_ldisc.c
> +++ b/drivers/bluetooth/hci_ldisc.c
> @@ -542,6 +542,9 @@ static int __init hci_uart_init(void)
> #ifdef CONFIG_BT_HCIUART_LL
> ll_init();
> #endif
> +#ifdef CONFIG_BT_HCIUART_ATH
> + ath_init();
> +#endif
>
> return 0;
> }
> @@ -559,6 +562,9 @@ static void __exit hci_uart_exit(void)
> #ifdef CONFIG_BT_HCIUART_LL
> ll_deinit();
> #endif
> +#ifdef CONFIG_BT_HCIUART_ATH
> + ath_deinit();
> +#endif
>
> /* Release tty registration of line discipline */
> if ((err = tty_unregister_ldisc(N_HCI)))
> diff --git a/drivers/bluetooth/hci_uart.h b/drivers/bluetooth/hci_uart.h
> index 50113db..385537f 100644
> --- a/drivers/bluetooth/hci_uart.h
> +++ b/drivers/bluetooth/hci_uart.h
> @@ -33,13 +33,14 @@
> #define HCIUARTGETDEVICE _IOR('U', 202, int)
>
> /* UART protocols */
> -#define HCI_UART_MAX_PROTO 5
> +#define HCI_UART_MAX_PROTO 6
>
> #define HCI_UART_H4 0
> #define HCI_UART_BCSP 1
> #define HCI_UART_3WIRE 2
> #define HCI_UART_H4DS 3
> #define HCI_UART_LL 4
> +#define HCI_UART_ATH 5
>
> struct hci_uart;
>
> @@ -91,3 +92,8 @@ int bcsp_deinit(void);
> int ll_init(void);
> int ll_deinit(void);
> #endif
> +
> +#ifdef CONFIG_BT_HCIUART_ATH
> +int ath_init(void);
> +int ath_deinit(void);
> +#endif
> --
> 1.6.3.3
>
next prev parent reply other threads:[~2010-02-17 9:55 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-09 11:43 [PATCH] Added support for Atheros AR300x UART Bluetooth Chip Vikram Kandukuri
2010-02-17 9:55 ` Vikram Kandukuri [this message]
2010-02-22 2:29 ` Marcel Holtmann
2010-02-22 8:54 ` Suraj Sumangala
2010-02-22 16:11 ` Luis R. Rodriguez
2010-02-23 5:42 ` Suraj Sumangala
2010-02-26 8:39 ` link starvation during multi profile scenario Suraj Sumangala
2010-03-01 9:53 ` [PATCH] Added support for Atheros AR300x UART Bluetooth Chip Suraj Sumangala
2010-03-11 13:18 ` [PATCH] Added support for Atheros AR300x " Suraj Sumangala
2010-03-11 17:15 ` Marcel Holtmann
2010-03-11 17:35 ` Luis R. Rodriguez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100217095542.GB2138@ATH-LT-538 \
--to=vkandukuri@atheros.com \
--cc=linux-bluetooth@vger.kernel.org \
--cc=marcel@holtmann.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox