Re: [RFC 3/3] Bluetooth: Add AMP initialization

['Emeltchenko Andrei' <Andrei.Emeltchenko.news@gmail.com>]

Hi Marcel,

On Fri, Nov 18, 2011 at 05:23:01PM +0100, Marcel Holtmann wrote:
> > > 
> > > However since we are talking about controller init. Can someone please
> > > first propose a list of how we init AMP vs BR/EDR/LE controllers instead
> > > of just dumping code here. I think it needs some clear strategy on how
> > > to do it.
> > 
> > AMP controller is initialized following way in Code Aurora code:
> > 
> > Common part:
> > 
> > <------8<--------------------------------------------------
> > |  /* Mandatory initialization */
> > |
> > |  /* Reset */
> > |  if (!test_bit(HCI_QUIRK_NO_RESET, &hdev->quirks)) {
> > |          set_bit(HCI_RESET, &hdev->flags);
> > |          hci_send_cmd(hdev, HCI_OP_RESET, 0, NULL);
> > |  }
> 
> this check for QUIRK_NO_RESET is pointless. That is just there for old
> Bluetooth 1.0b controllers. Or broken hardware. Let's assume the AMP
> controllers are fine and just issue OP_RESET.
> 
> > |  /* Read Local Version */
> > |  hci_send_cmd(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL);
> > |
> > |  /* Read HCI Flow Control Mode */
> > |  hci_send_cmd(hdev, HCI_OP_READ_FLOW_CONTROL_MODE, 0, NULL);
> > |
> > |  /* Read Buffer Size (ACL mtu, max pkt, etc.) */
> > |  hci_send_cmd(hdev, HCI_OP_READ_BUFFER_SIZE, 0, NULL);
> > |
> > |  /* Read Data Block Size (ACL mtu, max pkt, etc.) */
> > |  hci_send_cmd(hdev, HCI_OP_READ_DATA_BLOCK_SIZE, 0, NULL);
> > <------8<------------------------------------------------------
> 
> This is not a generic sequence. We will not be reading flow control or
> data block size commands. It will heavily fail on older controllers.

What about following code (basically BR/EDR initialization is the same as
now and only amp_init is new). I use now virtual AMP device so any init is
good, I need Read Version and Read AMP info commands.

static void bredr_init(struct hci_dev *hdev)
{
	struct hci_cp_delete_stored_link_key cp;
	__le16 param;
	__u8 flt_type;

	/* Mandatory initialization */
	/* Reset */
	if (!test_bit(HCI_QUIRK_NO_RESET, &hdev->quirks)) {
		set_bit(HCI_RESET, &hdev->flags);
		hci_send_cmd(hdev, HCI_OP_RESET, 0, NULL);
	}

	/* Read Local Supported Features */
	hci_send_cmd(hdev, HCI_OP_READ_LOCAL_FEATURES, 0, NULL);

	/* Read Local Version */
	hci_send_cmd(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL);

	/* Read Buffer Size (ACL mtu, max pkt, etc.) */
	hci_send_cmd(hdev, HCI_OP_READ_BUFFER_SIZE, 0, NULL);

	/* Read BD Address */
	hci_send_cmd(hdev, HCI_OP_READ_BD_ADDR, 0, NULL);

	/* Read Class of Device */
	hci_send_cmd(hdev, HCI_OP_READ_CLASS_OF_DEV, 0, NULL);

	/* Read Local Name */
	hci_send_cmd(hdev, HCI_OP_READ_LOCAL_NAME, 0, NULL);

	/* Read Voice Setting */
	hci_send_cmd(hdev, HCI_OP_READ_VOICE_SETTING, 0, NULL);

	/* Optional initialization */
	/* Clear Event Filters */
	flt_type = HCI_FLT_CLEAR_ALL;
	hci_send_cmd(hdev, HCI_OP_SET_EVENT_FLT, 1, &flt_type);

	/* Connection accept timeout ~20 secs */
	param = cpu_to_le16(0x7d00);
	hci_send_cmd(hdev, HCI_OP_WRITE_CA_TIMEOUT, 2, &param);

	bacpy(&cp.bdaddr, BDADDR_ANY);
	cp.delete_all = 1;
	hci_send_cmd(hdev, HCI_OP_DELETE_STORED_LINK_KEY, sizeof(cp), &cp);
}

static void amp_init(struct hci_dev *hdev)
{
	/* Mandatory initialization */
	/* Reset */
	hci_send_cmd(hdev, HCI_OP_RESET, 0, NULL);

	/* Read Local Version */
	hci_send_cmd(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL);

	/* Read Buffer Size (ACL mtu, max pkt, etc.) */
	hci_send_cmd(hdev, HCI_OP_READ_BUFFER_SIZE, 0, NULL);

	/* Read AMP Info */
	hci_send_cmd(hdev, HCI_OP_READ_LOCAL_AMP_INFO, 0, NULL);
}

Best regards 
Andrei Emeltchenko