* [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006]
@ 2012-12-29 10:14 Daniel Schaal
2012-12-29 10:14 ` [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k Daniel Schaal
0 siblings, 1 reply; 3+ messages in thread
From: Daniel Schaal @ 2012-12-29 10:14 UTC (permalink / raw)
To: Marcel Holtmann, Gustavo Padovan, Johan Hedberg, linux-bluetooth,
linux-kernel
Cc: Daniel Schaal
The following patch adds support for the bluetooth part of
Gigabyte's GC-WB300D PCIe card (combo card with AR9462 WLAN
and ATH3012 BT).
On every boot there is an error from this device:
usb 2-1.7: string descriptor 0 read error: -22
But that doesn't seem to have any negative effect AFAICT.
It also needed a newer firmware than is in linux-firmware.git,
using the one from the Windows driver worked fine.
(AthrBT_0x11020000.dfu and ramps_0x11020000_40.dfu)
Daniel Schaal (1):
Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k.
drivers/bluetooth/ath3k.c | 2 ++
drivers/bluetooth/btusb.c | 1 +
2 files changed, 3 insertions(+)
--
1.7.10.4
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k.
2012-12-29 10:14 [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] Daniel Schaal
@ 2012-12-29 10:14 ` Daniel Schaal
2013-01-03 20:07 ` Gustavo Padovan
0 siblings, 1 reply; 3+ messages in thread
From: Daniel Schaal @ 2012-12-29 10:14 UTC (permalink / raw)
To: Marcel Holtmann, Gustavo Padovan, Johan Hedberg, linux-bluetooth,
linux-kernel
Cc: Daniel Schaal
T: Bus=02 Lev=02 Prnt=02 Port=06 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3006 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Daniel Schaal <farbing@web.de>
---
drivers/bluetooth/ath3k.c | 2 ++
drivers/bluetooth/btusb.c | 1 +
2 files changed, 3 insertions(+)
diff --git a/drivers/bluetooth/ath3k.c b/drivers/bluetooth/ath3k.c
index b00000e..d936c5d 100644
--- a/drivers/bluetooth/ath3k.c
+++ b/drivers/bluetooth/ath3k.c
@@ -77,6 +77,7 @@ static struct usb_device_id ath3k_table[] = {
{ USB_DEVICE(0x0CF3, 0x311D) },
{ USB_DEVICE(0x13d3, 0x3375) },
{ USB_DEVICE(0x04CA, 0x3005) },
+ { USB_DEVICE(0x04CA, 0x3006) },
{ USB_DEVICE(0x13d3, 0x3362) },
{ USB_DEVICE(0x0CF3, 0xE004) },
{ USB_DEVICE(0x0930, 0x0219) },
@@ -104,6 +105,7 @@ static struct usb_device_id ath3k_blist_tbl[] = {
{ USB_DEVICE(0x0cf3, 0x311D), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x3005), .driver_info = BTUSB_ATH3012 },
+ { USB_DEVICE(0x04ca, 0x3006), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0930, 0x0219), .driver_info = BTUSB_ATH3012 },
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index a1d4ede..3252792 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -135,6 +135,7 @@ static struct usb_device_id blacklist_table[] = {
{ USB_DEVICE(0x0cf3, 0x311d), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x3005), .driver_info = BTUSB_ATH3012 },
+ { USB_DEVICE(0x04ca, 0x3006), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0930, 0x0219), .driver_info = BTUSB_ATH3012 },
--
1.7.10.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k.
2012-12-29 10:14 ` [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k Daniel Schaal
@ 2013-01-03 20:07 ` Gustavo Padovan
0 siblings, 0 replies; 3+ messages in thread
From: Gustavo Padovan @ 2013-01-03 20:07 UTC (permalink / raw)
To: Daniel Schaal
Cc: Marcel Holtmann, Johan Hedberg, linux-bluetooth, linux-kernel
Hi Daniel,
* Daniel Schaal <farbing@web.de> [2012-12-29 11:14:34 +0100]:
> T: Bus=02 Lev=02 Prnt=02 Port=06 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
> D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=04ca ProdID=3006 Rev= 0.02
> C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
>
> Signed-off-by: Daniel Schaal <farbing@web.de>
> ---
> drivers/bluetooth/ath3k.c | 2 ++
> drivers/bluetooth/btusb.c | 1 +
> 2 files changed, 3 insertions(+)
Patch has been applied to bluetooth.git. Thanks.
Gustavo
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2013-01-03 20:07 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-12-29 10:14 [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] Daniel Schaal
2012-12-29 10:14 ` [PATCH] Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k Daniel Schaal
2013-01-03 20:07 ` Gustavo Padovan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).