From: Lorenzo Ferrara <lorenzo.ferrara@gmx.it>
To: bluez-users@lists.sourceforge.net
Subject: [Bluez-users] Does the Trust BT180 (Broadcom 0x200a) work? and question on bnep0 device.
Date: Mon, 14 Mar 2005 13:15:42 +0100 [thread overview]
Message-ID: <4235806E.4020008@gmx.it> (raw)
Hello,
1) Does the Trust BT180 Class 1 Bluetooth Adapter work correctly,
without loading any firmware?
2) I tried to configure my Adapter so I could run ifconfing bnep0 ....
The only problem is that I don't have a bnep0 device. I read that I
need at list 2 working computers with a bluetooth adapter (working)
on both, and that I will have the bnep0 adapter only after I have run
pand --connect xx:xx:xx:xx:xx:xx --service GN
|__SERVER ADDRESS_|
Is that true?
Here is some info, if you ned anything else please ask.
--------------------------------------------------------------------
Kernel info:
--------------------------------------------------------------------
I have compiled as module everything under
Device Drivers -> Networking support -> Bluetooth subsystem support
uname -a :
Linux port0 2.6.11 #3 Sat Mar 12 12:32:53 CET 2005 i686 GNU/Linux
--------------------------------------------------------------------
lsmod:
Module Size Used by
hci_uart 15228 0
hci_vhci 5248 0
bcm203x 5124 0
bnep 12800 2
hidp 12544 0
rfcomm 35740 0
isofs 32952 1
hci_usb 10888 2
udf 85892 0
ppp_deflate 5120 0
zlib_deflate 21400 1 ppp_deflate
zlib_inflate 17408 2 isofs,ppp_deflate
bsd_comp 5632 0
ppp_async 9472 1
ppp_generic 22932 7 ppp_deflate,bsd_comp,ppp_async
slhc 6912 1 ppp_generic
binfmt_misc 9096 1
l2cap 23556 10 bnep,hidp,rfcomm
bluetooth 45060 11
hci_uart,hci_vhci,bnep,hidp,rfcomm,hci_usb,l2cap
powernow_k7 7464 0
cpufreq_userspace 3676 1
cpufreq_stats 4356 0
freq_table 3588 2 powernow_k7,cpufreq_stats
cpufreq_powersave 1664 0
cpufreq_ondemand 5404 0
thermal 11144 0
processor 18868 2 powernow_k7,thermal
fan 3332 0
button 5136 0
battery 8452 0
ac 3588 0
usbhid 31424 0
via_rhine 20484 0
i2c_viapro 6800 0
i2c_core 18704 1 i2c_viapro
via_ircc 23572 0
irda 119352 1 via_ircc
ehci_hcd 29192 0
uhci_hcd 29840 0
yenta_socket 19976 0
rsrc_nonstatic 9216 1 yenta_socket
pcmcia_core 42400 2 yenta_socket,rsrc_nonstatic
joydev 8128 0
ntfs 105968 1
ext2 44292 1
radeon 74624 1
drm 60692 2 radeon
via_agp 7680 1
agpgart 28712 2 drm,via_agp
parport_pc 25412 1
lp 8900 0
parport 32840 2 parport_pc,lp
sr_mod 14244 0
--------------------------------------------------------------------
This is the usb adapter:
--------------------------------------------------------------------
lsusb -v:
Bus 002 Device 005: ID 0a5c:200a Broadcom Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 224 Wireless
bDeviceSubClass 1 Radio Frequency
bDeviceProtocol 1 Bluetooth
bMaxPacketSize0 64
idVendor 0x0a5c Broadcom Corp.
idProduct 0x200a
bcdDevice 0.04
iManufacturer 1 Broadcom
iProduct 2 BCM92035DGROM
iSerial 3 000B0D6049E8
bNumConfigurations 1
[...]
--------------------------------------------------------------------
cat /proc/bus/usb/devices:
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=200a Rev= 0.04
S: Manufacturer=Broadcom
S: Product=BCM92035DGROM
S: SerialNumber=000B0D6049E8
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
--------------------------------------------------------------------
hciconfig :
hci0: Type: USB
BD Address: 00:0B:0D:60:49:E8 ACL MTU: 377:10 SCO MTU: 16:0
UP RUNNING PSCAN ISCAN AUTH ENCRYPT
RX bytes:338 acl:0 sco:0 events:48 errors:0
TX bytes:1440 acl:0 sco:0 commands:46 errors:0
--
____________________________________________
/ Lorenzo Ferrara /\
| lorenzo.ferrara <at> gmx <dot> it |_/
|___________________________________________|
| www.lorenzoferrara.net |
| www.aldebaransoftware.net |
| www.pot-pourri.zzn.com |
___|________________________________________ |
\___________________________________________\__/
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
next reply other threads:[~2005-03-14 12:15 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-03-14 12:15 Lorenzo Ferrara [this message]
2005-03-14 12:23 ` [Bluez-users] Does the Trust BT180 (Broadcom 0x200a) work? and question on bnep0 device Marcel Holtmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4235806E.4020008@gmx.it \
--to=lorenzo.ferrara@gmx.it \
--cc=bluez-users@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox