Marcel Holtmann wrote: > > > show us "hciconfig -a" and run "hcidump -X -V" as root while you are > scanning. Thanks for the reply Marcel, I have confirmed that this device does work on windows (a friends machine)... for a while I was wondering. Now on to the infomation requested: hcitool/hciconfig output: ------------------------- red:/home/dpb# hcitool scan Scanning ... Inquiry failed: Connection timed out red:/home/dpb# hciconfig -a: red:/home/dpb# hciconfig -a hci0: Type: USB BD Address: 00:0C:55:F8:5A:2B ACL MTU: 377:10 SCO MTU: 16:0 UP RUNNING PSCAN ISCAN INQUIRY AUTH RX bytes:101 acl:0 sco:0 events:13 errors:0 TX bytes:304 acl:0 sco:0 commands:13 errors:0 Features: 0xff 0xfe 0x0d 0x38 0x08 0x08 0x00 0x00 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: HOLD SNIFF PARK Link mode: ACCEPT MASTER Name: 'red (0)' Class: 0x000100 Service Classes: Unspecified Device Class: Computer, Uncategorized HCI Ver: 1.2 (0x2) HCI Rev: 0x0 LMP Ver: 1.2 (0x2) LMP Subver: 0x6965 Manufacturer: Broadcom Corporation (15) red:/home/dpb# hcidump -X -V output: --------------------- red:/home/dpb# hcidump -X -V HCI sniffer - Bluetooth packet analyzer ver 1.17 device: hci0 snap_len: 1028 filter: 0xffffffff < HCI Command: Inquiry (0x01|0x0001) plen 5 0000: 33 8b 9e 08 64 3...d > HCI Event: Command Status (0x0f) plen 4 Inquiry (0x01|0x0001) status 0x00 ncmd 1 < HCI Command: Read Local Name (0x03|0x0014) plen 0 > HCI Event: Command Complete (0x0e) plen 252 Read Local Name (0x03|0x0014) ncmd 1 status 0x00 0000: 72 65 64 20 28 30 29 00 00 00 00 00 00 00 00 00 red (0)......... 0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 0090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00f0: 00 00 00 00 00 00 00 00 ........ < HCI Command: Read Class of Device (0x03|0x0023) plen 0 > HCI Event: Command Complete (0x0e) plen 7 Read Class of Device (0x03|0x0023) ncmd 1 status 0x00 0000: 00 01 00 ... < HCI Command: Read Local Version Information (0x04|0x0001) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Read Local Version Information (0x04|0x0001) ncmd 1 status 0x00 0000: 02 00 00 02 0f 00 65 69 ......ei I ran the hcitool scan first, then the hciconfig -a, and both output through the dumper. If I try to run more hcitool scan commands, I don't get any output from those commands back in the dumper (probably still stuck on the first one?) until I unplug the device and plug it back in, etc. > > Also a "hcitool info" on the Treo would be nice. > I think I get similar results when running the hcitool info. However, when I run the hcitool info (got the device number off the windows install), the treo screen comes on (lights up) and it plays the "bluetooth connection sound". Nothing else, but at least that happens. :) hcitool info output: -------------------- red:/home/dpb# hcitool info 00:07:e0:05:0a:11 Requesting information ... Can't create connection: Connection timed out red:/home/dpb# hcidump from info request: -------------------------- red:/home/dpb# hcidump -X -V HCI sniffer - Bluetooth packet analyzer ver 1.17 device: hci0 snap_len: 1028 filter: 0xffffffff < HCI Command: Create Connection (0x01|0x0005) plen 13 0000: 11 0a 05 e0 07 00 18 cc 02 00 00 00 01 ............. < HCI Command: Create Connection (0x01|0x0005) plen 13 0000: 11 0a 05 e0 07 00 18 cc 02 00 00 00 01 ............. Not sure if it is helpful, but I also attached the syslog output during all these things. I appreciate your help. -- David Britton