Re: [PATCH v1] Bluetooth: hci_qca: Retry btsoc initialize when it fails

[rjliao@codeaurora.org]

Please ingnore this patch, I have just sent the new set of patches.

在 2019-12-19 14:52，Rocky Liao 写道：
> This patch adds the retry of btsoc initialization when it fails. There 
> are
> reports that the btsoc initialization may fail on some platforms but 
> the
> repro ratio is very low. The failure may be caused by UART, platform HW 
> or
> the btsoc itself but it's very difficlut to root cause, given the repro
> ratio is very low. Add a retry for the btsoc initialization will 
> resolve
> most of the failures and make Bluetooth finally works.
> 
> Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
> ---
>  drivers/bluetooth/hci_qca.c | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index 1cb706acdef6..af45b31f1b5f 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -53,6 +53,9 @@
>  /* Controller debug log header */
>  #define QCA_DEBUG_HANDLE	0x2EDC
> 
> +/* max retry count when init fails */
> +#define QCA_MAX_INIT_RETRY_COUNT 3
> +
>  enum qca_flags {
>  	QCA_IBS_ENABLED,
>  	QCA_DROP_VENDOR_EVENT,
> @@ -1259,6 +1262,7 @@ static int qca_setup(struct hci_uart *hu)
>  	struct qca_data *qca = hu->priv;
>  	struct qca_serdev *qcadev;
>  	unsigned int speed, qca_baudrate = QCA_BAUDRATE_115200;
> +	unsigned int init_retry_count = 0;
>  	enum qca_btsoc_type soc_type = qca_soc_type(hu);
>  	const char *firmware_name = qca_get_firmware_name(hu);
>  	int ret;
> @@ -1276,6 +1280,7 @@ static int qca_setup(struct hci_uart *hu)
>  	 */
>  	set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
> 
> +retry:
>  	if (qca_is_wcn399x(soc_type)) {
>  		bt_dev_info(hdev, "setting up wcn3990");
> 
> @@ -1341,6 +1346,20 @@ static int qca_setup(struct hci_uart *hu)
>  		 * patch/nvm-config is found, so run with original fw/config.
>  		 */
>  		ret = 0;
> +	} else {
> +		if (init_retry_count < QCA_MAX_INIT_RETRY_COUNT) {
> +			qca_power_off(hdev);
> +			if (hu->serdev) {
> +				serdev_device_close(hu->serdev);
> +				ret = serdev_device_open(hu->serdev);
> +				if (ret) {
> +					bt_dev_err(hu->hdev, "open port fail");
> +					return ret;
> +				}
> +			}
> +			init_retry_count++;
> +			goto retry;
> +		}
>  	}
> 
>  	/* Setup bdaddr */