* Can't bring bluetooth controller up
@ 2015-10-17 11:02 Julio González Mejías
2015-10-17 11:55 ` Marcel Holtmann
0 siblings, 1 reply; 6+ messages in thread
From: Julio González Mejías @ 2015-10-17 11:02 UTC (permalink / raw)
To: linux-bluetooth
Hi,
I have a card reader with bluetooth controller built-in (Broadcom
BCM2045A) and it stopped working suddenly some days ago as it appears
down and I can't bring it up with hciconfig, this is what happens:
sudo hciconfig hci0 up
Can't init device hci0: Operation not supported (95)
This is the output of hcidump when running this command:
hcidump
HCI sniffer - Bluetooth packet analyzer ver 5.35
device: hci0 snap_len: 1500 filter: 0xffffffffffffffff
> HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
status 0x00
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
status 0x00
Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 2.0 (0x3) HCI Revision: 0x2000
LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
Manufacturer: Broadcom Corporation (15)
> HCI Event: Command Complete (0x0e) plen 10
Read BD ADDR (0x04|0x0009) ncmd 1
status 0x00 bdaddr 25:7B:43:51:08:D3
> HCI Event: Command Complete (0x0e) plen 11
Read Buffer Size (0x04|0x0005) ncmd 1
status 0x00
ACL MTU 1017:8 SCO MTU 64:0
> HCI Event: Command Complete (0x0e) plen 7
Read Class of Device (0x03|0x0023) ncmd 1
status 0x00 class 0x000000
> HCI Event: Command Complete (0x0e) plen 252
Read Local Name (0x03|0x0014) ncmd 1
status 0x00 name 'BCM2045'
> HCI Event: Command Complete (0x0e) plen 6
Read Voice Setting (0x03|0x0025) ncmd 1
status 0x00 voice setting 0x0060
> HCI Event: Command Complete (0x0e) plen 5
Read Number of Supported IAC (0x03|0x0038) ncmd 1
> HCI Event: Command Complete (0x0e) plen 8
Read Current IAC LAP (0x03|0x0039) ncmd 1
IAC 0x9e8b33 (General Inquiry Access Code)
> HCI Event: Command Complete (0x0e) plen 4
Set Event Filter (0x03|0x0005) ncmd 1
status 0x00
> HCI Event: Command Complete (0x0e) plen 4
Write Connection Accept Timeout (0x03|0x0016) ncmd 1
status 0x00
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
status 0x00
Commands: ffffff03feffcfffffffffff0300f8ff07
> HCI Event: Command Complete (0x0e) plen 4
Write Inquiry Mode (0x03|0x0045) ncmd 1
status 0x00
> HCI Event: Command Complete (0x0e) plen 14
Read Local Extended Features (0x04|0x0004) ncmd 1
status 0x00 page 1 max 0
Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> HCI Event: Command Complete (0x0e) plen 4
Set Event Mask (0x03|0x0001) ncmd 1
status 0x00
> HCI Event: Command Complete (0x0e) plen 4
Write Default Link Policy Settings (0x02|0x000f) ncmd 1
status 0x00
> HCI Event: Command Complete (0x0e) plen 8
Read Page Scan Activity (0x03|0x001b) ncmd 1
status 0x00 interval 2048 window 18
> HCI Event: Command Complete (0x0e) plen 4
Delete Stored Link Key (0x03|0x0012) ncmd 1
status 0x11 deleted 2048
Error: Unsupported Feature or Parameter Value
I have looked on rfkill and everything seems correct and the LED is lit,
I'm using Arch Linux 4.2.3 kernel.
It still works on Windows, so I'm lost here, is the device faulty or
something?
Thanks in advance,
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Can't bring bluetooth controller up
2015-10-17 11:02 Can't bring bluetooth controller up Julio González Mejías
@ 2015-10-17 11:55 ` Marcel Holtmann
2015-10-17 12:12 ` Julio González Mejías
0 siblings, 1 reply; 6+ messages in thread
From: Marcel Holtmann @ 2015-10-17 11:55 UTC (permalink / raw)
To: Julio González Mejías; +Cc: linux-bluetooth
Hi Julio,
> I have a card reader with bluetooth controller built-in (Broadcom BCM2045A) and it stopped working suddenly some days ago as it appears down and I can't bring it up with hciconfig, this is what happens:
>
> sudo hciconfig hci0 up
> Can't init device hci0: Operation not supported (95)
>
> This is the output of hcidump when running this command:
>
> hcidump
> HCI sniffer - Bluetooth packet analyzer ver 5.35
> device: hci0 snap_len: 1500 filter: 0xffffffffffffffff
>> HCI Event: Command Complete (0x0e) plen 4
> Reset (0x03|0x0003) ncmd 1
> status 0x00
>> HCI Event: Command Complete (0x0e) plen 12
> Read Local Supported Features (0x04|0x0003) ncmd 1
> status 0x00
> Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
>> HCI Event: Command Complete (0x0e) plen 12
> Read Local Version Information (0x04|0x0001) ncmd 1
> status 0x00
> HCI Version: 2.0 (0x3) HCI Revision: 0x2000
> LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
> Manufacturer: Broadcom Corporation (15)
>> HCI Event: Command Complete (0x0e) plen 10
> Read BD ADDR (0x04|0x0009) ncmd 1
> status 0x00 bdaddr 25:7B:43:51:08:D3
>> HCI Event: Command Complete (0x0e) plen 11
> Read Buffer Size (0x04|0x0005) ncmd 1
> status 0x00
> ACL MTU 1017:8 SCO MTU 64:0
>> HCI Event: Command Complete (0x0e) plen 7
> Read Class of Device (0x03|0x0023) ncmd 1
> status 0x00 class 0x000000
>> HCI Event: Command Complete (0x0e) plen 252
> Read Local Name (0x03|0x0014) ncmd 1
> status 0x00 name 'BCM2045'
>> HCI Event: Command Complete (0x0e) plen 6
> Read Voice Setting (0x03|0x0025) ncmd 1
> status 0x00 voice setting 0x0060
>> HCI Event: Command Complete (0x0e) plen 5
> Read Number of Supported IAC (0x03|0x0038) ncmd 1
>> HCI Event: Command Complete (0x0e) plen 8
> Read Current IAC LAP (0x03|0x0039) ncmd 1
> IAC 0x9e8b33 (General Inquiry Access Code)
>> HCI Event: Command Complete (0x0e) plen 4
> Set Event Filter (0x03|0x0005) ncmd 1
> status 0x00
>> HCI Event: Command Complete (0x0e) plen 4
> Write Connection Accept Timeout (0x03|0x0016) ncmd 1
> status 0x00
>> HCI Event: Command Complete (0x0e) plen 68
> Read Local Supported Commands (0x04|0x0002) ncmd 1
> status 0x00
> Commands: ffffff03feffcfffffffffff0300f8ff07
>> HCI Event: Command Complete (0x0e) plen 4
> Write Inquiry Mode (0x03|0x0045) ncmd 1
> status 0x00
>> HCI Event: Command Complete (0x0e) plen 14
> Read Local Extended Features (0x04|0x0004) ncmd 1
> status 0x00 page 1 max 0
> Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
>> HCI Event: Command Complete (0x0e) plen 4
> Set Event Mask (0x03|0x0001) ncmd 1
> status 0x00
>> HCI Event: Command Complete (0x0e) plen 4
> Write Default Link Policy Settings (0x02|0x000f) ncmd 1
> status 0x00
>> HCI Event: Command Complete (0x0e) plen 8
> Read Page Scan Activity (0x03|0x001b) ncmd 1
> status 0x00 interval 2048 window 18
>> HCI Event: Command Complete (0x0e) plen 4
> Delete Stored Link Key (0x03|0x0012) ncmd 1
> status 0x11 deleted 2048
> Error: Unsupported Feature or Parameter Value
for some reason this command is failing. That should not happen actually. What is the content of /sys/kernel/debug/usb/devices for this device.
Regards
Marcel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Can't bring bluetooth controller up
2015-10-17 11:55 ` Marcel Holtmann
@ 2015-10-17 12:12 ` Julio González Mejías
2015-10-17 14:03 ` Marcel Holtmann
0 siblings, 1 reply; 6+ messages in thread
From: Julio González Mejías @ 2015-10-17 12:12 UTC (permalink / raw)
To: Marcel Holtmann; +Cc: linux-bluetooth
Hi Marcel,
> Hi Julio,
>
>> I have a card reader with bluetooth controller built-in (Broadcom
BCM2045A) and it stopped working suddenly some days ago as it appears
down and I can't bring it up with hciconfig, this is what happens:
>>
>> sudo hciconfig hci0 up
>> Can't init device hci0: Operation not supported (95)
>>
>> This is the output of hcidump when running this command:
>>
>> hcidump
>> HCI sniffer - Bluetooth packet analyzer ver 5.35
>> device: hci0 snap_len: 1500 filter: 0xffffffffffffffff
>>> HCI Event: Command Complete (0x0e) plen 4
>> Reset (0x03|0x0003) ncmd 1
>> status 0x00
>>> HCI Event: Command Complete (0x0e) plen 12
>> Read Local Supported Features (0x04|0x0003) ncmd 1
>> status 0x00
>> Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
>>> HCI Event: Command Complete (0x0e) plen 12
>> Read Local Version Information (0x04|0x0001) ncmd 1
>> status 0x00
>> HCI Version: 2.0 (0x3) HCI Revision: 0x2000
>> LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
>> Manufacturer: Broadcom Corporation (15)
>>> HCI Event: Command Complete (0x0e) plen 10
>> Read BD ADDR (0x04|0x0009) ncmd 1
>> status 0x00 bdaddr 25:7B:43:51:08:D3
>>> HCI Event: Command Complete (0x0e) plen 11
>> Read Buffer Size (0x04|0x0005) ncmd 1
>> status 0x00
>> ACL MTU 1017:8 SCO MTU 64:0
>>> HCI Event: Command Complete (0x0e) plen 7
>> Read Class of Device (0x03|0x0023) ncmd 1
>> status 0x00 class 0x000000
>>> HCI Event: Command Complete (0x0e) plen 252
>> Read Local Name (0x03|0x0014) ncmd 1
>> status 0x00 name 'BCM2045'
>>> HCI Event: Command Complete (0x0e) plen 6
>> Read Voice Setting (0x03|0x0025) ncmd 1
>> status 0x00 voice setting 0x0060
>>> HCI Event: Command Complete (0x0e) plen 5
>> Read Number of Supported IAC (0x03|0x0038) ncmd 1
>>> HCI Event: Command Complete (0x0e) plen 8
>> Read Current IAC LAP (0x03|0x0039) ncmd 1
>> IAC 0x9e8b33 (General Inquiry Access Code)
>>> HCI Event: Command Complete (0x0e) plen 4
>> Set Event Filter (0x03|0x0005) ncmd 1
>> status 0x00
>>> HCI Event: Command Complete (0x0e) plen 4
>> Write Connection Accept Timeout (0x03|0x0016) ncmd 1
>> status 0x00
>>> HCI Event: Command Complete (0x0e) plen 68
>> Read Local Supported Commands (0x04|0x0002) ncmd 1
>> status 0x00
>> Commands: ffffff03feffcfffffffffff0300f8ff07
>>> HCI Event: Command Complete (0x0e) plen 4
>> Write Inquiry Mode (0x03|0x0045) ncmd 1
>> status 0x00
>>> HCI Event: Command Complete (0x0e) plen 14
>> Read Local Extended Features (0x04|0x0004) ncmd 1
>> status 0x00 page 1 max 0
>> Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
>>> HCI Event: Command Complete (0x0e) plen 4
>> Set Event Mask (0x03|0x0001) ncmd 1
>> status 0x00
>>> HCI Event: Command Complete (0x0e) plen 4
>> Write Default Link Policy Settings (0x02|0x000f) ncmd 1
>> status 0x00
>>> HCI Event: Command Complete (0x0e) plen 8
>> Read Page Scan Activity (0x03|0x001b) ncmd 1
>> status 0x00 interval 2048 window 18
>>> HCI Event: Command Complete (0x0e) plen 4
>> Delete Stored Link Key (0x03|0x0012) ncmd 1
>> status 0x11 deleted 2048
>> Error: Unsupported Feature or Parameter Value
>
> for some reason this command is failing. That should not happen
actually. What is the content of /sys/kernel/debug/usb/devices for this
device.
>
> Regards
>
> Marcel
>
This is the content of /sys/kernel/debug/usb:
T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=2045 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM2045A
S: SerialNumber=000000000000
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Can't bring bluetooth controller up
2015-10-17 12:12 ` Julio González Mejías
@ 2015-10-17 14:03 ` Marcel Holtmann
2015-10-19 10:56 ` Julio González Mejías
0 siblings, 1 reply; 6+ messages in thread
From: Marcel Holtmann @ 2015-10-17 14:03 UTC (permalink / raw)
To: Julio González Mejías; +Cc: linux-bluetooth
Hi Julio,
> >> I have a card reader with bluetooth controller built-in (Broadcom BCM2045A) and it stopped working suddenly some days ago as it appears down and I can't bring it up with hciconfig, this is what happens:
> >>
> >> sudo hciconfig hci0 up
> >> Can't init device hci0: Operation not supported (95)
> >>
> >> This is the output of hcidump when running this command:
> >>
> >> hcidump
> >> HCI sniffer - Bluetooth packet analyzer ver 5.35
> >> device: hci0 snap_len: 1500 filter: 0xffffffffffffffff
> >>> HCI Event: Command Complete (0x0e) plen 4
> >> Reset (0x03|0x0003) ncmd 1
> >> status 0x00
> >>> HCI Event: Command Complete (0x0e) plen 12
> >> Read Local Supported Features (0x04|0x0003) ncmd 1
> >> status 0x00
> >> Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
> >>> HCI Event: Command Complete (0x0e) plen 12
> >> Read Local Version Information (0x04|0x0001) ncmd 1
> >> status 0x00
> >> HCI Version: 2.0 (0x3) HCI Revision: 0x2000
> >> LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
> >> Manufacturer: Broadcom Corporation (15)
> >>> HCI Event: Command Complete (0x0e) plen 10
> >> Read BD ADDR (0x04|0x0009) ncmd 1
> >> status 0x00 bdaddr 25:7B:43:51:08:D3
> >>> HCI Event: Command Complete (0x0e) plen 11
> >> Read Buffer Size (0x04|0x0005) ncmd 1
> >> status 0x00
> >> ACL MTU 1017:8 SCO MTU 64:0
> >>> HCI Event: Command Complete (0x0e) plen 7
> >> Read Class of Device (0x03|0x0023) ncmd 1
> >> status 0x00 class 0x000000
> >>> HCI Event: Command Complete (0x0e) plen 252
> >> Read Local Name (0x03|0x0014) ncmd 1
> >> status 0x00 name 'BCM2045'
> >>> HCI Event: Command Complete (0x0e) plen 6
> >> Read Voice Setting (0x03|0x0025) ncmd 1
> >> status 0x00 voice setting 0x0060
> >>> HCI Event: Command Complete (0x0e) plen 5
> >> Read Number of Supported IAC (0x03|0x0038) ncmd 1
> >>> HCI Event: Command Complete (0x0e) plen 8
> >> Read Current IAC LAP (0x03|0x0039) ncmd 1
> >> IAC 0x9e8b33 (General Inquiry Access Code)
> >>> HCI Event: Command Complete (0x0e) plen 4
> >> Set Event Filter (0x03|0x0005) ncmd 1
> >> status 0x00
> >>> HCI Event: Command Complete (0x0e) plen 4
> >> Write Connection Accept Timeout (0x03|0x0016) ncmd 1
> >> status 0x00
> >>> HCI Event: Command Complete (0x0e) plen 68
> >> Read Local Supported Commands (0x04|0x0002) ncmd 1
> >> status 0x00
> >> Commands: ffffff03feffcfffffffffff0300f8ff07
> >>> HCI Event: Command Complete (0x0e) plen 4
> >> Write Inquiry Mode (0x03|0x0045) ncmd 1
> >> status 0x00
> >>> HCI Event: Command Complete (0x0e) plen 14
> >> Read Local Extended Features (0x04|0x0004) ncmd 1
> >> status 0x00 page 1 max 0
> >> Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> >>> HCI Event: Command Complete (0x0e) plen 4
> >> Set Event Mask (0x03|0x0001) ncmd 1
> >> status 0x00
> >>> HCI Event: Command Complete (0x0e) plen 4
> >> Write Default Link Policy Settings (0x02|0x000f) ncmd 1
> >> status 0x00
> >>> HCI Event: Command Complete (0x0e) plen 8
> >> Read Page Scan Activity (0x03|0x001b) ncmd 1
> >> status 0x00 interval 2048 window 18
> >>> HCI Event: Command Complete (0x0e) plen 4
> >> Delete Stored Link Key (0x03|0x0012) ncmd 1
> >> status 0x11 deleted 2048
> >> Error: Unsupported Feature or Parameter Value
> >
> > for some reason this command is failing. That should not happen actually. What is the content of /sys/kernel/debug/usb/devices for this device.
> >
> > Regards
> >
> > Marcel
> >
>
> This is the content of /sys/kernel/debug/usb:
>
> T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
> D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=0a5c ProdID=2045 Rev= 1.12
> S: Manufacturer=Broadcom Corp
> S: Product=BCM2045A
> S: SerialNumber=000000000000
> C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
I sent a patch to the mailing list that might fix this. Please try it out.
Regards
Marcel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Can't bring bluetooth controller up
2015-10-17 14:03 ` Marcel Holtmann
@ 2015-10-19 10:56 ` Julio González Mejías
2015-10-19 11:25 ` Johan Hedberg
0 siblings, 1 reply; 6+ messages in thread
From: Julio González Mejías @ 2015-10-19 10:56 UTC (permalink / raw)
To: Marcel Holtmann; +Cc: linux-bluetooth
Hi Marcel,
> Hi Julio,
>
>>>> I have a card reader with bluetooth controller built-in (Broadcom BCM2045A) and it stopped working suddenly some days ago as it appears down and I can't bring it up with hciconfig, this is what happens:
>>>>
>>>> sudo hciconfig hci0 up
>>>> Can't init device hci0: Operation not supported (95)
>>>>
>>>> This is the output of hcidump when running this command:
>>>>
>>>> hcidump
>>>> HCI sniffer - Bluetooth packet analyzer ver 5.35
>>>> device: hci0 snap_len: 1500 filter: 0xffffffffffffffff
>>>>> HCI Event: Command Complete (0x0e) plen 4
>>>> Reset (0x03|0x0003) ncmd 1
>>>> status 0x00
>>>>> HCI Event: Command Complete (0x0e) plen 12
>>>> Read Local Supported Features (0x04|0x0003) ncmd 1
>>>> status 0x00
>>>> Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
>>>>> HCI Event: Command Complete (0x0e) plen 12
>>>> Read Local Version Information (0x04|0x0001) ncmd 1
>>>> status 0x00
>>>> HCI Version: 2.0 (0x3) HCI Revision: 0x2000
>>>> LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
>>>> Manufacturer: Broadcom Corporation (15)
>>>>> HCI Event: Command Complete (0x0e) plen 10
>>>> Read BD ADDR (0x04|0x0009) ncmd 1
>>>> status 0x00 bdaddr 25:7B:43:51:08:D3
>>>>> HCI Event: Command Complete (0x0e) plen 11
>>>> Read Buffer Size (0x04|0x0005) ncmd 1
>>>> status 0x00
>>>> ACL MTU 1017:8 SCO MTU 64:0
>>>>> HCI Event: Command Complete (0x0e) plen 7
>>>> Read Class of Device (0x03|0x0023) ncmd 1
>>>> status 0x00 class 0x000000
>>>>> HCI Event: Command Complete (0x0e) plen 252
>>>> Read Local Name (0x03|0x0014) ncmd 1
>>>> status 0x00 name 'BCM2045'
>>>>> HCI Event: Command Complete (0x0e) plen 6
>>>> Read Voice Setting (0x03|0x0025) ncmd 1
>>>> status 0x00 voice setting 0x0060
>>>>> HCI Event: Command Complete (0x0e) plen 5
>>>> Read Number of Supported IAC (0x03|0x0038) ncmd 1
>>>>> HCI Event: Command Complete (0x0e) plen 8
>>>> Read Current IAC LAP (0x03|0x0039) ncmd 1
>>>> IAC 0x9e8b33 (General Inquiry Access Code)
>>>>> HCI Event: Command Complete (0x0e) plen 4
>>>> Set Event Filter (0x03|0x0005) ncmd 1
>>>> status 0x00
>>>>> HCI Event: Command Complete (0x0e) plen 4
>>>> Write Connection Accept Timeout (0x03|0x0016) ncmd 1
>>>> status 0x00
>>>>> HCI Event: Command Complete (0x0e) plen 68
>>>> Read Local Supported Commands (0x04|0x0002) ncmd 1
>>>> status 0x00
>>>> Commands: ffffff03feffcfffffffffff0300f8ff07
>>>>> HCI Event: Command Complete (0x0e) plen 4
>>>> Write Inquiry Mode (0x03|0x0045) ncmd 1
>>>> status 0x00
>>>>> HCI Event: Command Complete (0x0e) plen 14
>>>> Read Local Extended Features (0x04|0x0004) ncmd 1
>>>> status 0x00 page 1 max 0
>>>> Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
>>>>> HCI Event: Command Complete (0x0e) plen 4
>>>> Set Event Mask (0x03|0x0001) ncmd 1
>>>> status 0x00
>>>>> HCI Event: Command Complete (0x0e) plen 4
>>>> Write Default Link Policy Settings (0x02|0x000f) ncmd 1
>>>> status 0x00
>>>>> HCI Event: Command Complete (0x0e) plen 8
>>>> Read Page Scan Activity (0x03|0x001b) ncmd 1
>>>> status 0x00 interval 2048 window 18
>>>>> HCI Event: Command Complete (0x0e) plen 4
>>>> Delete Stored Link Key (0x03|0x0012) ncmd 1
>>>> status 0x11 deleted 2048
>>>> Error: Unsupported Feature or Parameter Value
>>>
>>> for some reason this command is failing. That should not happen actually. What is the content of /sys/kernel/debug/usb/devices for this device.
>>>
>>> Regards
>>>
>>> Marcel
>>>
>>
>> This is the content of /sys/kernel/debug/usb:
>>
>> T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
>> D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
>> P: Vendor=0a5c ProdID=2045 Rev= 1.12
>> S: Manufacturer=Broadcom Corp
>> S: Product=BCM2045A
>> S: SerialNumber=000000000000
>> C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
>> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
>> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
>> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
>> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
>> I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
>> I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
>> I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
>> I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
>> I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
>> I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
>> E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
>> E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
>> I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
>
> I sent a patch to the mailing list that might fix this. Please try it out.
>
> Regards
>
> Marcel
>
Thank you! I have tried the patch and my bluetooth controller works fine
now.
Regards
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Can't bring bluetooth controller up
2015-10-19 10:56 ` Julio González Mejías
@ 2015-10-19 11:25 ` Johan Hedberg
0 siblings, 0 replies; 6+ messages in thread
From: Johan Hedberg @ 2015-10-19 11:25 UTC (permalink / raw)
To: Julio González Mejías; +Cc: Marcel Holtmann, linux-bluetooth
Hi Julio,
On Mon, Oct 19, 2015, Julio González Mejías wrote:
> >I sent a patch to the mailing list that might fix this. Please try it out.
> >
> >Regards
> >
> >Marcel
> >
>
> Thank you! I have tried the patch and my bluetooth controller works fine
> now.
Thanks for testing this. I've now applied the patch to bluetooth-next.
Johan
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2015-10-19 11:25 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-10-17 11:02 Can't bring bluetooth controller up Julio González Mejías
2015-10-17 11:55 ` Marcel Holtmann
2015-10-17 12:12 ` Julio González Mejías
2015-10-17 14:03 ` Marcel Holtmann
2015-10-19 10:56 ` Julio González Mejías
2015-10-19 11:25 ` Johan Hedberg
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).