* [PATCH v1 0/2] Enable Bluetooth functinality for WCN6750
@ 2021-03-11 16:58 Venkata Lakshmi Narayana Gubba
2021-03-11 16:58 ` [PATCH v1 1/2] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750 Venkata Lakshmi Narayana Gubba
2021-03-11 16:58 ` [PATCH v1 2/2] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750 Venkata Lakshmi Narayana Gubba
0 siblings, 2 replies; 7+ messages in thread
From: Venkata Lakshmi Narayana Gubba @ 2021-03-11 16:58 UTC (permalink / raw)
To: marcel, johan.hedberg
Cc: devicetree, mka, linux-kernel, linux-bluetooth, hemantg,
linux-arm-msm, bgodavar, rjliao, hbandi, abhishekpandit,
Venkata Lakshmi Narayana Gubba
These patches enables Bluetooth functinalties for new Qualcomm
Bluetooth SoC wcn6750.
This SoC requires both regulators and GPIO to turn on/off.
This SoC supports mbn format image for firmware download.
Venkata Lakshmi Narayana Gubba (2):
Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
dt-bindings: net: bluetooth: Add device tree bindings for QTI chip
wcn6750
.../devicetree/bindings/net/qualcomm-bluetooth.txt | 43 +++++++++
drivers/bluetooth/btqca.c | 85 ++++++++++++-----
drivers/bluetooth/btqca.h | 15 ++-
drivers/bluetooth/hci_qca.c | 106 ++++++++++++++++-----
4 files changed, 202 insertions(+), 47 deletions(-)
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v1 1/2] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
2021-03-11 16:58 [PATCH v1 0/2] Enable Bluetooth functinality for WCN6750 Venkata Lakshmi Narayana Gubba
@ 2021-03-11 16:58 ` Venkata Lakshmi Narayana Gubba
2021-03-11 17:53 ` Enable Bluetooth functinality for WCN6750 bluez.test.bot
2021-03-11 16:58 ` [PATCH v1 2/2] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750 Venkata Lakshmi Narayana Gubba
1 sibling, 1 reply; 7+ messages in thread
From: Venkata Lakshmi Narayana Gubba @ 2021-03-11 16:58 UTC (permalink / raw)
To: marcel, johan.hedberg
Cc: devicetree, mka, linux-kernel, linux-bluetooth, hemantg,
linux-arm-msm, bgodavar, rjliao, hbandi, abhishekpandit,
Venkata Lakshmi Narayana Gubba
Added regulators,GPIOs and changes required to power on/off wcn6750.
Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn399x or wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and
renamed it to qca_regulator_init().
5. Added BT_ON and BT_OFF macros.
6. Added support to download mbn type firmware image as wcn6750 supports
mbn type image.
7. If mbn type image is not present then we will check for tlv type image.
8. Moved extracting rom version info to common place as this code is
common in all if else ladder in qca_uart_setup.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
drivers/bluetooth/btqca.c | 85 +++++++++++++++++++++++++----------
drivers/bluetooth/btqca.h | 15 ++++++-
drivers/bluetooth/hci_qca.c | 106 ++++++++++++++++++++++++++++++++++----------
3 files changed, 159 insertions(+), 47 deletions(-)
diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 25114f0..00ce0e9 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -182,7 +182,8 @@ int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
}
EXPORT_SYMBOL_GPL(qca_send_pre_shutdown_cmd);
-static void qca_tlv_check_data(struct qca_fw_config *config,
+static void qca_tlv_check_data(struct hci_dev *hdev,
+ struct qca_fw_config *config,
const struct firmware *fw, enum qca_btsoc_type soc_type)
{
const u8 *data;
@@ -194,19 +195,21 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
struct tlv_type_nvm *tlv_nvm;
uint8_t nvm_baud_rate = config->user_baud_rate;
- tlv = (struct tlv_type_hdr *)fw->data;
-
- type_len = le32_to_cpu(tlv->type_len);
- length = (type_len >> 8) & 0x00ffffff;
-
- BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
- BT_DBG("Length\t\t : %d bytes", length);
-
config->dnld_mode = QCA_SKIP_EVT_NONE;
config->dnld_type = QCA_SKIP_EVT_NONE;
switch (config->type) {
+ case ELF_TYPE_PATCH:
+ config->dnld_mode = QCA_SKIP_EVT_VSE_CC;
+ config->dnld_type = QCA_SKIP_EVT_VSE_CC;
+
+ bt_dev_dbg(hdev, "File Class : 0x%x", fw->data[4]);
+ bt_dev_dbg(hdev, "Data Encoding : 0x%x", fw->data[5]);
+ bt_dev_dbg(hdev, "File version : 0x%x", fw->data[6]);
+ break;
case TLV_TYPE_PATCH:
+ tlv = (struct tlv_type_hdr *)fw->data;
+ type_len = le32_to_cpu(tlv->type_len);
tlv_patch = (struct tlv_type_patch *)tlv->data;
/* For Rome version 1.1 to 3.1, all segment commands
@@ -218,6 +221,7 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
config->dnld_mode = tlv_patch->download_mode;
config->dnld_type = config->dnld_mode;
+ BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
BT_DBG("Total Length : %d bytes",
le32_to_cpu(tlv_patch->total_size));
BT_DBG("Patch Data Length : %d bytes",
@@ -243,6 +247,14 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
break;
case TLV_TYPE_NVM:
+ tlv = (struct tlv_type_hdr *)fw->data;
+
+ type_len = le32_to_cpu(tlv->type_len);
+ length = (type_len >> 8) & 0x00ffffff;
+
+ BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
+ BT_DBG("Length\t\t : %d bytes", length);
+
idx = 0;
data = tlv->data;
while (idx < length) {
@@ -387,7 +399,8 @@ static int qca_inject_cmd_complete_event(struct hci_dev *hdev)
static int qca_download_firmware(struct hci_dev *hdev,
struct qca_fw_config *config,
- enum qca_btsoc_type soc_type)
+ enum qca_btsoc_type soc_type,
+ u8 rom_ver)
{
const struct firmware *fw;
const u8 *segment;
@@ -397,12 +410,29 @@ static int qca_download_firmware(struct hci_dev *hdev,
ret = request_firmware(&fw, config->fwname, &hdev->dev);
if (ret) {
- bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
- config->fwname, ret);
- return ret;
+ /* For WCN6750, if mbn file is not present then check for
+ * tlv file.
+ */
+ if (soc_type == QCA_WCN6750 && config->type == ELF_TYPE_PATCH) {
+ bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ config->type = TLV_TYPE_PATCH;
+ snprintf(config->fwname, sizeof(config->fwname),
+ "qca/msbtfw%02x.tlv", rom_ver);
+ ret = request_firmware(&fw, config->fwname, &hdev->dev);
+ if (ret) {
+ bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ return ret;
+ }
+ } else {
+ bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ return ret;
+ }
}
- qca_tlv_check_data(config, fw, soc_type);
+ qca_tlv_check_data(hdev, config, fw, soc_type);
segment = fw->data;
remain = fw->size;
@@ -502,27 +532,33 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
config.user_baud_rate = baudrate;
+ /* Firmware files to download are based on ROM version.
+ * ROM version is derived from last two bytes of soc_ver.
+ */
+ rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
+ (soc_ver & 0x0000000f);
+
/* Download rampatch file */
config.type = TLV_TYPE_PATCH;
if (qca_is_wcn399x(soc_type)) {
- /* Firmware files to download are based on ROM version.
- * ROM version is derived from last two bytes of soc_ver.
- */
- rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
- (soc_ver & 0x0000000f);
snprintf(config.fwname, sizeof(config.fwname),
"qca/crbtfw%02x.tlv", rom_ver);
} else if (soc_type == QCA_QCA6390) {
- rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
- (soc_ver & 0x0000000f);
snprintf(config.fwname, sizeof(config.fwname),
"qca/htbtfw%02x.tlv", rom_ver);
+ } else if (soc_type == QCA_WCN6750) {
+ /* Choose mbn file by default.If mbn file is not found
+ * then choose tlv file
+ */
+ config.type = ELF_TYPE_PATCH;
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/msbtfw%02x.mbn", rom_ver);
} else {
snprintf(config.fwname, sizeof(config.fwname),
"qca/rampatch_%08x.bin", soc_ver);
}
- err = qca_download_firmware(hdev, &config, soc_type);
+ err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
if (err < 0) {
bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
return err;
@@ -548,11 +584,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
else if (soc_type == QCA_QCA6390)
snprintf(config.fwname, sizeof(config.fwname),
"qca/htnv%02x.bin", rom_ver);
+ else if (soc_type == QCA_WCN6750)
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/msnv%02x.bin", rom_ver);
else
snprintf(config.fwname, sizeof(config.fwname),
"qca/nvm_%08x.bin", soc_ver);
- err = qca_download_firmware(hdev, &config, soc_type);
+ err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
if (err < 0) {
bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
return err;
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index b19add7..3057bf8 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -80,7 +80,8 @@ enum qca_tlv_dnld_mode {
enum qca_tlv_type {
TLV_TYPE_PATCH = 1,
- TLV_TYPE_NVM
+ TLV_TYPE_NVM,
+ ELF_TYPE_PATCH
};
struct qca_fw_config {
@@ -143,6 +144,7 @@ enum qca_btsoc_type {
QCA_WCN3998,
QCA_WCN3991,
QCA_QCA6390,
+ QCA_WCN6750
};
#if IS_ENABLED(CONFIG_BT_QCA)
@@ -160,6 +162,12 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
soc_type == QCA_WCN3998;
}
+static inline bool qca_is_wcn399x_wcn6750(enum qca_btsoc_type soc_type)
+{
+ return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
+ soc_type == QCA_WCN3998 || soc_type == QCA_WCN6750;
+}
+
#else
static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
@@ -192,6 +200,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
return false;
}
+static inline bool qca_is_wcn399x_wcn6750(enum qca_btsoc_type soc_type)
+{
+ return false;
+}
+
static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
{
return -EOPNOTSUPP;
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 73af901..8959a6d 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -70,6 +70,10 @@
#define QCA_CRASHBYTE_PACKET_LEN 1096
#define QCA_MEMDUMP_BYTE 0xFB
+/* BT_EN GPIO enable/disable */
+#define BT_ON 1
+#define BT_OFF 0
+
enum qca_flags {
QCA_IBS_DISABLED,
QCA_DROP_VENDOR_EVENT,
@@ -218,6 +222,7 @@ struct qca_power {
struct qca_serdev {
struct hci_uart serdev_hu;
struct gpio_desc *bt_en;
+ struct gpio_desc *sw_ctrl;
struct clk *susclk;
enum qca_btsoc_type btsoc_type;
struct qca_power *bt_power;
@@ -604,7 +609,7 @@ static int qca_open(struct hci_uart *hu)
if (hu->serdev) {
qcadev = serdev_device_get_drvdata(hu->serdev);
- if (qca_is_wcn399x(qcadev->btsoc_type))
+ if (qca_is_wcn399x_wcn6750(qcadev->btsoc_type))
hu->init_speed = qcadev->init_speed;
if (qcadev->oper_speed)
@@ -1308,7 +1313,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));
/* Give the controller time to process the request */
- if (qca_is_wcn399x(qca_soc_type(hu)))
+ if (qca_is_wcn399x_wcn6750(qca_soc_type(hu)))
usleep_range(1000, 10000);
else
msleep(300);
@@ -1384,7 +1389,7 @@ static unsigned int qca_get_speed(struct hci_uart *hu,
static int qca_check_speeds(struct hci_uart *hu)
{
- if (qca_is_wcn399x(qca_soc_type(hu))) {
+ if (qca_is_wcn399x_wcn6750(qca_soc_type(hu))) {
if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
!qca_get_speed(hu, QCA_OPER_SPEED))
return -EINVAL;
@@ -1417,7 +1422,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
/* Disable flow control for wcn3990 to deassert RTS while
* changing the baudrate of chip and host.
*/
- if (qca_is_wcn399x(soc_type))
+ if (qca_is_wcn399x_wcn6750(soc_type))
hci_uart_set_flow_control(hu, true);
if (soc_type == QCA_WCN3990) {
@@ -1434,7 +1439,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
host_set_baudrate(hu, speed);
error:
- if (qca_is_wcn399x(soc_type))
+ if (qca_is_wcn399x_wcn6750(soc_type))
hci_uart_set_flow_control(hu, false);
if (soc_type == QCA_WCN3990) {
@@ -1585,10 +1590,12 @@ static bool qca_prevent_wake(struct hci_dev *hdev)
return !wakeup;
}
-static int qca_wcn3990_init(struct hci_uart *hu)
+static int qca_regulator_init(struct hci_uart *hu)
{
+ enum qca_btsoc_type soc_type = qca_soc_type(hu);
struct qca_serdev *qcadev;
int ret;
+ bool sw_ctrl_state;
/* Check for vregs status, may be hci down has turned
* off the voltage regulator.
@@ -1607,16 +1614,31 @@ static int qca_wcn3990_init(struct hci_uart *hu)
}
}
- /* Forcefully enable wcn3990 to enter in to boot mode. */
- host_set_baudrate(hu, 2400);
- ret = qca_send_power_pulse(hu, false);
- if (ret)
- return ret;
+ if (qca_is_wcn399x(soc_type)) {
+ /* Forcefully enable wcn3990 to enter in to boot mode. */
+ host_set_baudrate(hu, 2400);
+ ret = qca_send_power_pulse(hu, false);
+ if (ret)
+ return ret;
+ }
+
+ /* For wcn6750 need to enable gpio bt_en */
+ if (qcadev->bt_en) {
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
+ msleep(50);
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_ON);
+ msleep(50);
+ sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+ bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
+ }
qca_set_speed(hu, QCA_INIT_SPEED);
- ret = qca_send_power_pulse(hu, true);
- if (ret)
- return ret;
+
+ if (qca_is_wcn399x(soc_type)) {
+ ret = qca_send_power_pulse(hu, true);
+ if (ret)
+ return ret;
+ }
/* Now the device is in ready state to communicate with host.
* To sync host with device we need to reopen port.
@@ -1649,12 +1671,12 @@ static int qca_power_on(struct hci_dev *hdev)
if (!hu->serdev)
return 0;
- if (qca_is_wcn399x(soc_type)) {
- ret = qca_wcn3990_init(hu);
+ if (qca_is_wcn399x_wcn6750(soc_type)) {
+ ret = qca_regulator_init(hu);
} else {
qcadev = serdev_device_get_drvdata(hu->serdev);
if (qcadev->bt_en) {
- gpiod_set_value_cansleep(qcadev->bt_en, 1);
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_ON);
/* Controller needs time to bootup. */
msleep(150);
}
@@ -1689,7 +1711,8 @@ static int qca_setup(struct hci_uart *hu)
set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
bt_dev_info(hdev, "setting up %s",
- qca_is_wcn399x(soc_type) ? "wcn399x" : "ROME/QCA6390");
+ qca_is_wcn399x(soc_type) ? "wcn399x" :
+ (soc_type == QCA_WCN6750) ? "wcn6750" : "ROME/QCA6390");
qca->memdump_state = QCA_MEMDUMP_IDLE;
@@ -1700,7 +1723,7 @@ static int qca_setup(struct hci_uart *hu)
clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
- if (qca_is_wcn399x(soc_type)) {
+ if (qca_is_wcn399x_wcn6750(soc_type)) {
set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
ret = qca_read_soc_version(hdev, &ver, soc_type);
@@ -1720,7 +1743,7 @@ static int qca_setup(struct hci_uart *hu)
qca_baudrate = qca_get_baudrate_value(speed);
}
- if (!qca_is_wcn399x(soc_type)) {
+ if (!qca_is_wcn399x_wcn6750(soc_type)) {
/* Get QCA version information */
ret = qca_read_soc_version(hdev, &ver, soc_type);
if (ret)
@@ -1828,12 +1851,30 @@ static const struct qca_device_data qca_soc_data_qca6390 = {
.num_vregs = 0,
};
+static const struct qca_device_data qca_soc_data_wcn6750 = {
+ .soc_type = QCA_WCN6750,
+ .vregs = (struct qca_vreg []) {
+ { "vddio", 5000 },
+ { "vddaon", 26000 },
+ { "vddbtcxmx", 126000 },
+ { "vddrfacmn", 12500 },
+ { "vddrfa0p8", 102000 },
+ { "vddrfa1p7", 302000 },
+ { "vddrfa1p2", 257000 },
+ { "vddrfa2p2", 1700000 },
+ { "vddasd", 200 },
+ },
+ .num_vregs = 9,
+ .capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
+};
+
static void qca_power_shutdown(struct hci_uart *hu)
{
struct qca_serdev *qcadev;
struct qca_data *qca = hu->priv;
unsigned long flags;
enum qca_btsoc_type soc_type = qca_soc_type(hu);
+ bool sw_ctrl_state;
qcadev = serdev_device_get_drvdata(hu->serdev);
@@ -1856,8 +1897,14 @@ static void qca_power_shutdown(struct hci_uart *hu)
host_set_baudrate(hu, 2400);
qca_send_power_pulse(hu, false);
qca_regulator_disable(qcadev);
+ } else if (soc_type == QCA_WCN6750) {
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
+ msleep(100);
+ qca_regulator_disable(qcadev);
+ sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+ bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
} else if (qcadev->bt_en) {
- gpiod_set_value_cansleep(qcadev->bt_en, 0);
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
}
set_bit(QCA_BT_OFF, &qca->flags);
@@ -1978,7 +2025,7 @@ static int qca_serdev_probe(struct serdev_device *serdev)
if (!qcadev->oper_speed)
BT_DBG("UART will pick default operating speed");
- if (data && qca_is_wcn399x(data->soc_type)) {
+ if (data && qca_is_wcn399x_wcn6750(data->soc_type)) {
qcadev->btsoc_type = data->soc_type;
qcadev->bt_power = devm_kzalloc(&serdev->dev,
sizeof(struct qca_power),
@@ -1996,6 +2043,18 @@ static int qca_serdev_probe(struct serdev_device *serdev)
qcadev->bt_power->vregs_on = false;
+ qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
+ GPIOD_OUT_LOW);
+ if (!qcadev->bt_en && data->soc_type == QCA_WCN6750) {
+ dev_err(&serdev->dev, "failed to acquire BT_EN gpio\n");
+ power_ctrl_enabled = false;
+ }
+
+ qcadev->sw_ctrl = devm_gpiod_get_optional(&serdev->dev, "swctrl",
+ GPIOD_IN);
+ if (!qcadev->sw_ctrl && data->soc_type == QCA_WCN6750)
+ dev_warn(&serdev->dev, "failed to acquire SW_CTRL gpio\n");
+
qcadev->susclk = devm_clk_get_optional(&serdev->dev, NULL);
if (IS_ERR(qcadev->susclk)) {
dev_err(&serdev->dev, "failed to acquire clk\n");
@@ -2068,7 +2127,7 @@ static void qca_serdev_remove(struct serdev_device *serdev)
struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
struct qca_power *power = qcadev->bt_power;
- if (qca_is_wcn399x(qcadev->btsoc_type) && power->vregs_on)
+ if (qca_is_wcn399x_wcn6750(qcadev->btsoc_type) && power->vregs_on)
qca_power_shutdown(&qcadev->serdev_hu);
else if (qcadev->susclk)
clk_disable_unprepare(qcadev->susclk);
@@ -2244,6 +2303,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = {
{ .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990},
{ .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991},
{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
+ { .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread* RE: Enable Bluetooth functinality for WCN6750
2021-03-11 16:58 ` [PATCH v1 1/2] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750 Venkata Lakshmi Narayana Gubba
@ 2021-03-11 17:53 ` bluez.test.bot
0 siblings, 0 replies; 7+ messages in thread
From: bluez.test.bot @ 2021-03-11 17:53 UTC (permalink / raw)
To: linux-bluetooth, gubbaven
[-- Attachment #1: Type: text/plain, Size: 1791 bytes --]
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=446435
---Test result---
##############################
Test: CheckPatch - PASS
##############################
Test: CheckGitLint - FAIL
dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
1: T1 Title exceeds max length (74>72): "dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750"
##############################
Test: CheckBuildK - PASS
##############################
Test: CheckTestRunner: Setup - PASS
##############################
Test: CheckTestRunner: l2cap-tester - PASS
Total: 40, Passed: 34 (85.0%), Failed: 0, Not Run: 6
##############################
Test: CheckTestRunner: bnep-tester - PASS
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: mgmt-tester - FAIL
Total: 416, Passed: 399 (95.9%), Failed: 3, Not Run: 14
##############################
Test: CheckTestRunner: rfcomm-tester - PASS
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: sco-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: smp-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: userchan-tester - PASS
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
[-- Attachment #2: l2cap-tester.log --]
[-- Type: application/octet-stream, Size: 43408 bytes --]
[-- Attachment #3: bnep-tester.log --]
[-- Type: application/octet-stream, Size: 3532 bytes --]
[-- Attachment #4: mgmt-tester.log --]
[-- Type: application/octet-stream, Size: 547124 bytes --]
[-- Attachment #5: rfcomm-tester.log --]
[-- Type: application/octet-stream, Size: 11652 bytes --]
[-- Attachment #6: sco-tester.log --]
[-- Type: application/octet-stream, Size: 9888 bytes --]
[-- Attachment #7: smp-tester.log --]
[-- Type: application/octet-stream, Size: 11799 bytes --]
[-- Attachment #8: userchan-tester.log --]
[-- Type: application/octet-stream, Size: 5429 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v1 2/2] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
2021-03-11 16:58 [PATCH v1 0/2] Enable Bluetooth functinality for WCN6750 Venkata Lakshmi Narayana Gubba
2021-03-11 16:58 ` [PATCH v1 1/2] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750 Venkata Lakshmi Narayana Gubba
@ 2021-03-11 16:58 ` Venkata Lakshmi Narayana Gubba
2021-03-24 15:18 ` Rob Herring
1 sibling, 1 reply; 7+ messages in thread
From: Venkata Lakshmi Narayana Gubba @ 2021-03-11 16:58 UTC (permalink / raw)
To: marcel, johan.hedberg
Cc: devicetree, mka, linux-kernel, linux-bluetooth, hemantg,
linux-arm-msm, bgodavar, rjliao, hbandi, abhishekpandit,
Venkata Lakshmi Narayana Gubba
This patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750
controller.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
.../devicetree/bindings/net/qualcomm-bluetooth.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
index 709ca6d..e70fcb7 100644
--- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
+++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
@@ -15,6 +15,7 @@ Required properties:
* "qcom,wcn3991-bt"
* "qcom,wcn3998-bt"
* "qcom,qca6390-bt"
+ * "qcom,wcn6750-bt"
Optional properties for compatible string qcom,qca6174-bt:
@@ -39,6 +40,26 @@ Optional properties for compatible string qcom,wcn399x-bt:
- firmware-name: specify the name of nvm firmware to load
- clocks: clock provided to the controller
+Required properties for compatible string qcom,wcn6750-bt:
+
+ - enable-gpios: gpio specifier used to enable chip
+ - swctrl-gpios: gpio specifier is output from SoC,used to find status
+ of clock supply to SoC.
+ - vddio-supply: VDD_IO supply regulator handle.
+ - vddaon-supply: VDD_AON supply regulator handle.
+ - vddbtcxmx-suppl: VDD_BT_CXMX supply regualtor handle.
+ - vddrfacmn-supply: VDD_RFA_CMN supply regulator handle.
+ - vddrfa0p8-supply: VDD_RFA_0P8 suppply regulator handle.
+ - vddrfa1p7-supply: VDD_RFA_1P7 supply regulator handle.
+ - vddrfa1p2-supply: VDD_RFA_1P2 supply regulator handle.
+ - vddrfa2p2-supply: VDD_RFA_2P2 supply regulator handle.
+ - vddasd-supply: VDD_ASD supply regulator handle.
+
+Optional properties for compatible string qcom,wcn6750-bt:
+
+ - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml
+ - firmware-name: specify the name of nvm firmware to load
+
Examples:
serial@7570000 {
@@ -67,3 +88,25 @@ serial@898000 {
clocks = <&rpmhcc RPMH_RF_CLK2>;
};
};
+
+serial@99c000 {
+ bluetooth {
+ compatible = "qcom,wcn6750-bt";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en_default>;
+ enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+ swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+ vddio-supply = <&vreg_l19b_1p8>;
+ vddaon-supply = <&vreg_s7b_0p9>;
+ vddbtcxmx-supply = <&vreg_s7b_0p9>;
+ vddrfacmn-supply = <&vreg_s7b_0p9>;
+ vddrfa0p8-supply = <&vreg_s7b_0p9>;
+ vddrfa1p7-supply = <&vreg_s1b_1p8>;
+ vddrfa1p2-supply = <&vreg_s8b_1p2>;
+ vddrfa2p2-supply = <&vreg_s1c_2p2>;
+ vddasd-supply = <&vreg_l11c_2p8>;
+ max-speed = <3200000>;
+ firmware-name = "msnv11.bin";
+ };
+};
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH v1 2/2] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
2021-03-11 16:58 ` [PATCH v1 2/2] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750 Venkata Lakshmi Narayana Gubba
@ 2021-03-24 15:18 ` Rob Herring
0 siblings, 0 replies; 7+ messages in thread
From: Rob Herring @ 2021-03-24 15:18 UTC (permalink / raw)
To: Venkata Lakshmi Narayana Gubba
Cc: marcel, johan.hedberg, devicetree, mka, linux-kernel,
linux-bluetooth, hemantg, linux-arm-msm, bgodavar, rjliao, hbandi,
abhishekpandit
On Thu, Mar 11, 2021 at 10:28:24PM +0530, Venkata Lakshmi Narayana Gubba wrote:
> This patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750
> controller.
>
> Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
> ---
> .../devicetree/bindings/net/qualcomm-bluetooth.txt | 43 ++++++++++++++++++++++
> 1 file changed, 43 insertions(+)
This is a large change. Please convert to DT schema first.
>
> diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> index 709ca6d..e70fcb7 100644
> --- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> @@ -15,6 +15,7 @@ Required properties:
> * "qcom,wcn3991-bt"
> * "qcom,wcn3998-bt"
> * "qcom,qca6390-bt"
> + * "qcom,wcn6750-bt"
>
> Optional properties for compatible string qcom,qca6174-bt:
>
> @@ -39,6 +40,26 @@ Optional properties for compatible string qcom,wcn399x-bt:
> - firmware-name: specify the name of nvm firmware to load
> - clocks: clock provided to the controller
>
> +Required properties for compatible string qcom,wcn6750-bt:
> +
> + - enable-gpios: gpio specifier used to enable chip
> + - swctrl-gpios: gpio specifier is output from SoC,used to find status
> + of clock supply to SoC.
> + - vddio-supply: VDD_IO supply regulator handle.
> + - vddaon-supply: VDD_AON supply regulator handle.
> + - vddbtcxmx-suppl: VDD_BT_CXMX supply regualtor handle.
> + - vddrfacmn-supply: VDD_RFA_CMN supply regulator handle.
> + - vddrfa0p8-supply: VDD_RFA_0P8 suppply regulator handle.
> + - vddrfa1p7-supply: VDD_RFA_1P7 supply regulator handle.
> + - vddrfa1p2-supply: VDD_RFA_1P2 supply regulator handle.
> + - vddrfa2p2-supply: VDD_RFA_2P2 supply regulator handle.
> + - vddasd-supply: VDD_ASD supply regulator handle.
> +
> +Optional properties for compatible string qcom,wcn6750-bt:
> +
> + - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml
> + - firmware-name: specify the name of nvm firmware to load
> +
> Examples:
>
> serial@7570000 {
> @@ -67,3 +88,25 @@ serial@898000 {
> clocks = <&rpmhcc RPMH_RF_CLK2>;
> };
> };
> +
> +serial@99c000 {
> + bluetooth {
> + compatible = "qcom,wcn6750-bt";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_en_default>;
> + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
> + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
> + vddio-supply = <&vreg_l19b_1p8>;
> + vddaon-supply = <&vreg_s7b_0p9>;
> + vddbtcxmx-supply = <&vreg_s7b_0p9>;
> + vddrfacmn-supply = <&vreg_s7b_0p9>;
> + vddrfa0p8-supply = <&vreg_s7b_0p9>;
> + vddrfa1p7-supply = <&vreg_s1b_1p8>;
> + vddrfa1p2-supply = <&vreg_s8b_1p2>;
> + vddrfa2p2-supply = <&vreg_s1c_2p2>;
> + vddasd-supply = <&vreg_l11c_2p8>;
> + max-speed = <3200000>;
> + firmware-name = "msnv11.bin";
> + };
> +};
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v2 1/3] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
@ 2021-04-20 16:26 Venkata Lakshmi Narayana Gubba
2021-04-20 17:46 ` Enable Bluetooth functinality for WCN6750 bluez.test.bot
0 siblings, 1 reply; 7+ messages in thread
From: Venkata Lakshmi Narayana Gubba @ 2021-04-20 16:26 UTC (permalink / raw)
To: marcel, johan.hedberg, devicetree
Cc: mka, linux-kernel, linux-bluetooth, hemantg, linux-arm-msm,
bgodavar, rjliao, hbandi, abhishekpandit,
Venkata Lakshmi Narayana Gubba
Added regulators,GPIOs and changes required to power on/off wcn6750.
Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn399x or wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and
renamed it to qca_regulator_init().
5. Added BT_ON and BT_OFF macros.
6. Added support to download mbn type firmware image as wcn6750 supports
mbn type image.
7. If mbn type image is not present then we will check for tlv type image.
8. Moved extracting rom version info to common place as this code is
common in all if else ladder in qca_uart_setup.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
drivers/bluetooth/btqca.c | 88 ++++++++++++++++++++++++++----------
drivers/bluetooth/btqca.h | 15 ++++++-
drivers/bluetooth/hci_qca.c | 106 ++++++++++++++++++++++++++++++++++----------
3 files changed, 161 insertions(+), 48 deletions(-)
diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 25114f0..eec391a 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -182,7 +182,8 @@ int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
}
EXPORT_SYMBOL_GPL(qca_send_pre_shutdown_cmd);
-static void qca_tlv_check_data(struct qca_fw_config *config,
+static void qca_tlv_check_data(struct hci_dev *hdev,
+ struct qca_fw_config *config,
const struct firmware *fw, enum qca_btsoc_type soc_type)
{
const u8 *data;
@@ -194,19 +195,21 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
struct tlv_type_nvm *tlv_nvm;
uint8_t nvm_baud_rate = config->user_baud_rate;
- tlv = (struct tlv_type_hdr *)fw->data;
-
- type_len = le32_to_cpu(tlv->type_len);
- length = (type_len >> 8) & 0x00ffffff;
-
- BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
- BT_DBG("Length\t\t : %d bytes", length);
-
config->dnld_mode = QCA_SKIP_EVT_NONE;
config->dnld_type = QCA_SKIP_EVT_NONE;
switch (config->type) {
+ case ELF_TYPE_PATCH:
+ config->dnld_mode = QCA_SKIP_EVT_VSE_CC;
+ config->dnld_type = QCA_SKIP_EVT_VSE_CC;
+
+ bt_dev_dbg(hdev, "File Class : 0x%x", fw->data[4]);
+ bt_dev_dbg(hdev, "Data Encoding : 0x%x", fw->data[5]);
+ bt_dev_dbg(hdev, "File version : 0x%x", fw->data[6]);
+ break;
case TLV_TYPE_PATCH:
+ tlv = (struct tlv_type_hdr *)fw->data;
+ type_len = le32_to_cpu(tlv->type_len);
tlv_patch = (struct tlv_type_patch *)tlv->data;
/* For Rome version 1.1 to 3.1, all segment commands
@@ -218,6 +221,7 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
config->dnld_mode = tlv_patch->download_mode;
config->dnld_type = config->dnld_mode;
+ BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
BT_DBG("Total Length : %d bytes",
le32_to_cpu(tlv_patch->total_size));
BT_DBG("Patch Data Length : %d bytes",
@@ -243,6 +247,14 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
break;
case TLV_TYPE_NVM:
+ tlv = (struct tlv_type_hdr *)fw->data;
+
+ type_len = le32_to_cpu(tlv->type_len);
+ length = (type_len >> 8) & 0x00ffffff;
+
+ BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
+ BT_DBG("Length\t\t : %d bytes", length);
+
idx = 0;
data = tlv->data;
while (idx < length) {
@@ -387,7 +399,8 @@ static int qca_inject_cmd_complete_event(struct hci_dev *hdev)
static int qca_download_firmware(struct hci_dev *hdev,
struct qca_fw_config *config,
- enum qca_btsoc_type soc_type)
+ enum qca_btsoc_type soc_type,
+ u8 rom_ver)
{
const struct firmware *fw;
const u8 *segment;
@@ -397,12 +410,29 @@ static int qca_download_firmware(struct hci_dev *hdev,
ret = request_firmware(&fw, config->fwname, &hdev->dev);
if (ret) {
- bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
- config->fwname, ret);
- return ret;
+ /* For WCN6750, if mbn file is not present then check for
+ * tlv file.
+ */
+ if (soc_type == QCA_WCN6750 && config->type == ELF_TYPE_PATCH) {
+ bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ config->type = TLV_TYPE_PATCH;
+ snprintf(config->fwname, sizeof(config->fwname),
+ "qca/msbtfw%02x.tlv", rom_ver);
+ ret = request_firmware(&fw, config->fwname, &hdev->dev);
+ if (ret) {
+ bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ return ret;
+ }
+ } else {
+ bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+ config->fwname, ret);
+ return ret;
+ }
}
- qca_tlv_check_data(config, fw, soc_type);
+ qca_tlv_check_data(hdev, config, fw, soc_type);
segment = fw->data;
remain = fw->size;
@@ -502,27 +532,33 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
config.user_baud_rate = baudrate;
+ /* Firmware files to download are based on ROM version.
+ * ROM version is derived from last two bytes of soc_ver.
+ */
+ rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
+ (soc_ver & 0x0000000f);
+
/* Download rampatch file */
config.type = TLV_TYPE_PATCH;
if (qca_is_wcn399x(soc_type)) {
- /* Firmware files to download are based on ROM version.
- * ROM version is derived from last two bytes of soc_ver.
- */
- rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
- (soc_ver & 0x0000000f);
snprintf(config.fwname, sizeof(config.fwname),
"qca/crbtfw%02x.tlv", rom_ver);
} else if (soc_type == QCA_QCA6390) {
- rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
- (soc_ver & 0x0000000f);
snprintf(config.fwname, sizeof(config.fwname),
"qca/htbtfw%02x.tlv", rom_ver);
+ } else if (soc_type == QCA_WCN6750) {
+ /* Choose mbn file by default.If mbn file is not found
+ * then choose tlv file
+ */
+ config.type = ELF_TYPE_PATCH;
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/msbtfw%02x.mbn", rom_ver);
} else {
snprintf(config.fwname, sizeof(config.fwname),
"qca/rampatch_%08x.bin", soc_ver);
}
- err = qca_download_firmware(hdev, &config, soc_type);
+ err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
if (err < 0) {
bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
return err;
@@ -548,11 +584,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
else if (soc_type == QCA_QCA6390)
snprintf(config.fwname, sizeof(config.fwname),
"qca/htnv%02x.bin", rom_ver);
+ else if (soc_type == QCA_WCN6750)
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/msnv%02x.bin", rom_ver);
else
snprintf(config.fwname, sizeof(config.fwname),
"qca/nvm_%08x.bin", soc_ver);
- err = qca_download_firmware(hdev, &config, soc_type);
+ err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
if (err < 0) {
bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
return err;
@@ -564,13 +603,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
return err;
}
- /* WCN399x supports the Microsoft vendor extension with 0xFD70 as the
+ /* WCN399x and WCN6750 supports the Microsoft vendor extension with 0xFD70 as the
* VsMsftOpCode.
*/
switch (soc_type) {
case QCA_WCN3990:
case QCA_WCN3991:
case QCA_WCN3998:
+ case QCA_WCN6750:
hci_set_msft_opcode(hdev, 0xFD70);
break;
default:
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index b19add7..3057bf8 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -80,7 +80,8 @@ enum qca_tlv_dnld_mode {
enum qca_tlv_type {
TLV_TYPE_PATCH = 1,
- TLV_TYPE_NVM
+ TLV_TYPE_NVM,
+ ELF_TYPE_PATCH
};
struct qca_fw_config {
@@ -143,6 +144,7 @@ enum qca_btsoc_type {
QCA_WCN3998,
QCA_WCN3991,
QCA_QCA6390,
+ QCA_WCN6750
};
#if IS_ENABLED(CONFIG_BT_QCA)
@@ -160,6 +162,12 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
soc_type == QCA_WCN3998;
}
+static inline bool qca_is_wcn399x_wcn6750(enum qca_btsoc_type soc_type)
+{
+ return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
+ soc_type == QCA_WCN3998 || soc_type == QCA_WCN6750;
+}
+
#else
static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
@@ -192,6 +200,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
return false;
}
+static inline bool qca_is_wcn399x_wcn6750(enum qca_btsoc_type soc_type)
+{
+ return false;
+}
+
static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
{
return -EOPNOTSUPP;
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 0a00569..0d25ba9 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -70,6 +70,10 @@
#define QCA_CRASHBYTE_PACKET_LEN 1096
#define QCA_MEMDUMP_BYTE 0xFB
+/* BT_EN GPIO enable/disable */
+#define BT_ON 1
+#define BT_OFF 0
+
enum qca_flags {
QCA_IBS_DISABLED,
QCA_DROP_VENDOR_EVENT,
@@ -218,6 +222,7 @@ struct qca_power {
struct qca_serdev {
struct hci_uart serdev_hu;
struct gpio_desc *bt_en;
+ struct gpio_desc *sw_ctrl;
struct clk *susclk;
enum qca_btsoc_type btsoc_type;
struct qca_power *bt_power;
@@ -604,7 +609,7 @@ static int qca_open(struct hci_uart *hu)
if (hu->serdev) {
qcadev = serdev_device_get_drvdata(hu->serdev);
- if (qca_is_wcn399x(qcadev->btsoc_type))
+ if (qca_is_wcn399x_wcn6750(qcadev->btsoc_type))
hu->init_speed = qcadev->init_speed;
if (qcadev->oper_speed)
@@ -1308,7 +1313,7 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));
/* Give the controller time to process the request */
- if (qca_is_wcn399x(qca_soc_type(hu)))
+ if (qca_is_wcn399x_wcn6750(qca_soc_type(hu)))
usleep_range(1000, 10000);
else
msleep(300);
@@ -1384,7 +1389,7 @@ static unsigned int qca_get_speed(struct hci_uart *hu,
static int qca_check_speeds(struct hci_uart *hu)
{
- if (qca_is_wcn399x(qca_soc_type(hu))) {
+ if (qca_is_wcn399x_wcn6750(qca_soc_type(hu))) {
if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
!qca_get_speed(hu, QCA_OPER_SPEED))
return -EINVAL;
@@ -1417,7 +1422,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
/* Disable flow control for wcn3990 to deassert RTS while
* changing the baudrate of chip and host.
*/
- if (qca_is_wcn399x(soc_type))
+ if (qca_is_wcn399x_wcn6750(soc_type))
hci_uart_set_flow_control(hu, true);
if (soc_type == QCA_WCN3990) {
@@ -1434,7 +1439,7 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
host_set_baudrate(hu, speed);
error:
- if (qca_is_wcn399x(soc_type))
+ if (qca_is_wcn399x_wcn6750(soc_type))
hci_uart_set_flow_control(hu, false);
if (soc_type == QCA_WCN3990) {
@@ -1585,10 +1590,12 @@ static bool qca_prevent_wake(struct hci_dev *hdev)
return !wakeup;
}
-static int qca_wcn3990_init(struct hci_uart *hu)
+static int qca_regulator_init(struct hci_uart *hu)
{
+ enum qca_btsoc_type soc_type = qca_soc_type(hu);
struct qca_serdev *qcadev;
int ret;
+ bool sw_ctrl_state;
/* Check for vregs status, may be hci down has turned
* off the voltage regulator.
@@ -1607,16 +1614,31 @@ static int qca_wcn3990_init(struct hci_uart *hu)
}
}
- /* Forcefully enable wcn3990 to enter in to boot mode. */
- host_set_baudrate(hu, 2400);
- ret = qca_send_power_pulse(hu, false);
- if (ret)
- return ret;
+ if (qca_is_wcn399x(soc_type)) {
+ /* Forcefully enable wcn3990 to enter in to boot mode. */
+ host_set_baudrate(hu, 2400);
+ ret = qca_send_power_pulse(hu, false);
+ if (ret)
+ return ret;
+ }
+
+ /* For wcn6750 need to enable gpio bt_en */
+ if (qcadev->bt_en) {
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
+ msleep(50);
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_ON);
+ msleep(50);
+ sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+ bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
+ }
qca_set_speed(hu, QCA_INIT_SPEED);
- ret = qca_send_power_pulse(hu, true);
- if (ret)
- return ret;
+
+ if (qca_is_wcn399x(soc_type)) {
+ ret = qca_send_power_pulse(hu, true);
+ if (ret)
+ return ret;
+ }
/* Now the device is in ready state to communicate with host.
* To sync host with device we need to reopen port.
@@ -1649,12 +1671,12 @@ static int qca_power_on(struct hci_dev *hdev)
if (!hu->serdev)
return 0;
- if (qca_is_wcn399x(soc_type)) {
- ret = qca_wcn3990_init(hu);
+ if (qca_is_wcn399x_wcn6750(soc_type)) {
+ ret = qca_regulator_init(hu);
} else {
qcadev = serdev_device_get_drvdata(hu->serdev);
if (qcadev->bt_en) {
- gpiod_set_value_cansleep(qcadev->bt_en, 1);
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_ON);
/* Controller needs time to bootup. */
msleep(150);
}
@@ -1689,7 +1711,8 @@ static int qca_setup(struct hci_uart *hu)
set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
bt_dev_info(hdev, "setting up %s",
- qca_is_wcn399x(soc_type) ? "wcn399x" : "ROME/QCA6390");
+ qca_is_wcn399x(soc_type) ? "wcn399x" :
+ (soc_type == QCA_WCN6750) ? "wcn6750" : "ROME/QCA6390");
qca->memdump_state = QCA_MEMDUMP_IDLE;
@@ -1700,7 +1723,7 @@ static int qca_setup(struct hci_uart *hu)
clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
- if (qca_is_wcn399x(soc_type)) {
+ if (qca_is_wcn399x_wcn6750(soc_type)) {
set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
ret = qca_read_soc_version(hdev, &ver, soc_type);
@@ -1720,7 +1743,7 @@ static int qca_setup(struct hci_uart *hu)
qca_baudrate = qca_get_baudrate_value(speed);
}
- if (!qca_is_wcn399x(soc_type)) {
+ if (!qca_is_wcn399x_wcn6750(soc_type)) {
/* Get QCA version information */
ret = qca_read_soc_version(hdev, &ver, soc_type);
if (ret)
@@ -1828,12 +1851,30 @@ static const struct qca_device_data qca_soc_data_qca6390 = {
.num_vregs = 0,
};
+static const struct qca_device_data qca_soc_data_wcn6750 = {
+ .soc_type = QCA_WCN6750,
+ .vregs = (struct qca_vreg []) {
+ { "vddio", 5000 },
+ { "vddaon", 26000 },
+ { "vddbtcxmx", 126000 },
+ { "vddrfacmn", 12500 },
+ { "vddrfa0p8", 102000 },
+ { "vddrfa1p7", 302000 },
+ { "vddrfa1p2", 257000 },
+ { "vddrfa2p2", 1700000 },
+ { "vddasd", 200 },
+ },
+ .num_vregs = 9,
+ .capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
+};
+
static void qca_power_shutdown(struct hci_uart *hu)
{
struct qca_serdev *qcadev;
struct qca_data *qca = hu->priv;
unsigned long flags;
enum qca_btsoc_type soc_type = qca_soc_type(hu);
+ bool sw_ctrl_state;
qcadev = serdev_device_get_drvdata(hu->serdev);
@@ -1856,8 +1897,14 @@ static void qca_power_shutdown(struct hci_uart *hu)
host_set_baudrate(hu, 2400);
qca_send_power_pulse(hu, false);
qca_regulator_disable(qcadev);
+ } else if (soc_type == QCA_WCN6750) {
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
+ msleep(100);
+ qca_regulator_disable(qcadev);
+ sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+ bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
} else if (qcadev->bt_en) {
- gpiod_set_value_cansleep(qcadev->bt_en, 0);
+ gpiod_set_value_cansleep(qcadev->bt_en, BT_OFF);
}
set_bit(QCA_BT_OFF, &qca->flags);
@@ -1978,7 +2025,7 @@ static int qca_serdev_probe(struct serdev_device *serdev)
if (!qcadev->oper_speed)
BT_DBG("UART will pick default operating speed");
- if (data && qca_is_wcn399x(data->soc_type)) {
+ if (data && qca_is_wcn399x_wcn6750(data->soc_type)) {
qcadev->btsoc_type = data->soc_type;
qcadev->bt_power = devm_kzalloc(&serdev->dev,
sizeof(struct qca_power),
@@ -1996,6 +2043,18 @@ static int qca_serdev_probe(struct serdev_device *serdev)
qcadev->bt_power->vregs_on = false;
+ qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
+ GPIOD_OUT_LOW);
+ if (!qcadev->bt_en && data->soc_type == QCA_WCN6750) {
+ dev_err(&serdev->dev, "failed to acquire BT_EN gpio\n");
+ power_ctrl_enabled = false;
+ }
+
+ qcadev->sw_ctrl = devm_gpiod_get_optional(&serdev->dev, "swctrl",
+ GPIOD_IN);
+ if (!qcadev->sw_ctrl && data->soc_type == QCA_WCN6750)
+ dev_warn(&serdev->dev, "failed to acquire SW_CTRL gpio\n");
+
qcadev->susclk = devm_clk_get_optional(&serdev->dev, NULL);
if (IS_ERR(qcadev->susclk)) {
dev_err(&serdev->dev, "failed to acquire clk\n");
@@ -2068,7 +2127,7 @@ static void qca_serdev_remove(struct serdev_device *serdev)
struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
struct qca_power *power = qcadev->bt_power;
- if (qca_is_wcn399x(qcadev->btsoc_type) && power->vregs_on)
+ if (qca_is_wcn399x_wcn6750(qcadev->btsoc_type) && power->vregs_on)
qca_power_shutdown(&qcadev->serdev_hu);
else if (qcadev->susclk)
clk_disable_unprepare(qcadev->susclk);
@@ -2244,6 +2303,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = {
{ .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990},
{ .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991},
{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
+ { .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread* RE: Enable Bluetooth functinality for WCN6750
2021-04-20 16:26 [PATCH v2 1/3] Bluetooth: hci_qca: Add support for QTI Bluetooth " Venkata Lakshmi Narayana Gubba
@ 2021-04-20 17:46 ` bluez.test.bot
0 siblings, 0 replies; 7+ messages in thread
From: bluez.test.bot @ 2021-04-20 17:46 UTC (permalink / raw)
To: linux-bluetooth, gubbaven
[-- Attachment #1: Type: text/plain, Size: 3111 bytes --]
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=470381
---Test result---
##############################
Test: CheckPatch - FAIL
dt-bindings: net: bluetooth: Convert to DT schema
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#11:
deleted file mode 100644
WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
ERROR: trailing whitespace
#114: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:24:
+ - qcom,qca6390-bt $
ERROR: trailing whitespace
#119: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:29:
+ $
ERROR: trailing whitespace
#136: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:46:
+ max-speed: $
ERROR: trailing whitespace
#175: FILE: Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml:85:
+ firmware-name = "crnv21.bin";^I^I$
total: 4 errors, 3 warnings, 87 lines checked
NOTE: For some of the reported defects, checkpatch may be able to
mechanically convert to the typical style using --fix or --fix-inplace.
NOTE: Whitespace errors detected.
You may wish to use scripts/cleanpatch or scripts/cleanfile
"[PATCH] dt-bindings: net: bluetooth: Convert to DT schema" has style problems, please review.
NOTE: If any of the errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
##############################
Test: CheckGitLint - FAIL
dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
1: T1 Title exceeds max length (74>72): "dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750"
##############################
Test: CheckBuildK - PASS
##############################
Test: CheckTestRunner: Setup - PASS
##############################
Test: CheckTestRunner: l2cap-tester - PASS
Total: 40, Passed: 34 (85.0%), Failed: 0, Not Run: 6
##############################
Test: CheckTestRunner: bnep-tester - PASS
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: mgmt-tester - PASS
Total: 416, Passed: 402 (96.6%), Failed: 0, Not Run: 14
##############################
Test: CheckTestRunner: rfcomm-tester - PASS
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: sco-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: smp-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: userchan-tester - PASS
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
[-- Attachment #2: l2cap-tester.log --]
[-- Type: application/octet-stream, Size: 43346 bytes --]
[-- Attachment #3: bnep-tester.log --]
[-- Type: application/octet-stream, Size: 3536 bytes --]
[-- Attachment #4: mgmt-tester.log --]
[-- Type: application/octet-stream, Size: 546684 bytes --]
[-- Attachment #5: rfcomm-tester.log --]
[-- Type: application/octet-stream, Size: 11657 bytes --]
[-- Attachment #6: sco-tester.log --]
[-- Type: application/octet-stream, Size: 9892 bytes --]
[-- Attachment #7: smp-tester.log --]
[-- Type: application/octet-stream, Size: 11803 bytes --]
[-- Attachment #8: userchan-tester.log --]
[-- Type: application/octet-stream, Size: 5433 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v3 1/5] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
@ 2021-05-06 17:33 Venkata Lakshmi Narayana Gubba
2021-05-06 18:29 ` Enable Bluetooth functinality for WCN6750 bluez.test.bot
0 siblings, 1 reply; 7+ messages in thread
From: Venkata Lakshmi Narayana Gubba @ 2021-05-06 17:33 UTC (permalink / raw)
To: marcel, johan.hedberg, devicetree
Cc: mka, linux-kernel, linux-bluetooth, hemantg, linux-arm-msm,
bgodavar, rjliao, hbandi, abhishekpandit,
Venkata Lakshmi Narayana Gubba
Added regulators,GPIOs and changes required to power on/off wcn6750.
Added support for firmware download for wcn6750.
Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and
renamed it to qca_regulator_init().
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
drivers/bluetooth/btqca.c | 13 ++++-
drivers/bluetooth/btqca.h | 11 +++++
drivers/bluetooth/hci_qca.c | 114 ++++++++++++++++++++++++++++++++++++--------
3 files changed, 115 insertions(+), 23 deletions(-)
diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 25114f0..fce808c 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -517,6 +517,11 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
(soc_ver & 0x0000000f);
snprintf(config.fwname, sizeof(config.fwname),
"qca/htbtfw%02x.tlv", rom_ver);
+ } else if (soc_type == QCA_WCN6750) {
+ rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
+ (soc_ver & 0x0000000f);
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/msbtfw%02x.tlv", rom_ver);
} else {
snprintf(config.fwname, sizeof(config.fwname),
"qca/rampatch_%08x.bin", soc_ver);
@@ -548,6 +553,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
else if (soc_type == QCA_QCA6390)
snprintf(config.fwname, sizeof(config.fwname),
"qca/htnv%02x.bin", rom_ver);
+ else if (soc_type == QCA_WCN6750)
+ snprintf(config.fwname, sizeof(config.fwname),
+ "qca/msnv%02x.bin", rom_ver);
else
snprintf(config.fwname, sizeof(config.fwname),
"qca/nvm_%08x.bin", soc_ver);
@@ -564,13 +572,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
return err;
}
- /* WCN399x supports the Microsoft vendor extension with 0xFD70 as the
+ /* WCN399x and WCN6750 supports the Microsoft vendor extension with 0xFD70 as the
* VsMsftOpCode.
*/
switch (soc_type) {
case QCA_WCN3990:
case QCA_WCN3991:
case QCA_WCN3998:
+ case QCA_WCN6750:
hci_set_msft_opcode(hdev, 0xFD70);
break;
default:
@@ -584,7 +593,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
return err;
}
- if (soc_type == QCA_WCN3991) {
+ if (soc_type == QCA_WCN3991 || soc_type == QCA_WCN6750) {
/* get fw build info */
err = qca_read_fw_build_info(hdev);
if (err < 0)
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index b19add7..dd82d2c 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -143,6 +143,7 @@ enum qca_btsoc_type {
QCA_WCN3998,
QCA_WCN3991,
QCA_QCA6390,
+ QCA_WCN6750
};
#if IS_ENABLED(CONFIG_BT_QCA)
@@ -160,6 +161,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
soc_type == QCA_WCN3998;
}
+static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
+{
+ return soc_type == QCA_WCN6750;
+}
+
#else
static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
@@ -192,6 +198,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
return false;
}
+static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
+{
+ return false;
+}
+
static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
{
return -EOPNOTSUPP;
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 0a00569..0d7a1c5 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -218,6 +218,7 @@ struct qca_power {
struct qca_serdev {
struct hci_uart serdev_hu;
struct gpio_desc *bt_en;
+ struct gpio_desc *sw_ctrl;
struct clk *susclk;
enum qca_btsoc_type btsoc_type;
struct qca_power *bt_power;
@@ -604,7 +605,8 @@ static int qca_open(struct hci_uart *hu)
if (hu->serdev) {
qcadev = serdev_device_get_drvdata(hu->serdev);
- if (qca_is_wcn399x(qcadev->btsoc_type))
+ if (qca_is_wcn399x(qcadev->btsoc_type) ||
+ qca_is_wcn6750(qcadev->btsoc_type))
hu->init_speed = qcadev->init_speed;
if (qcadev->oper_speed)
@@ -1308,7 +1310,8 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));
/* Give the controller time to process the request */
- if (qca_is_wcn399x(qca_soc_type(hu)))
+ if (qca_is_wcn399x(qca_soc_type(hu)) ||
+ qca_is_wcn6750(qca_soc_type(hu)))
usleep_range(1000, 10000);
else
msleep(300);
@@ -1384,7 +1387,8 @@ static unsigned int qca_get_speed(struct hci_uart *hu,
static int qca_check_speeds(struct hci_uart *hu)
{
- if (qca_is_wcn399x(qca_soc_type(hu))) {
+ if (qca_is_wcn399x(qca_soc_type(hu)) ||
+ qca_is_wcn6750(qca_soc_type(hu))) {
if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
!qca_get_speed(hu, QCA_OPER_SPEED))
return -EINVAL;
@@ -1417,7 +1421,8 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
/* Disable flow control for wcn3990 to deassert RTS while
* changing the baudrate of chip and host.
*/
- if (qca_is_wcn399x(soc_type))
+ if (qca_is_wcn399x(soc_type) ||
+ qca_is_wcn6750(soc_type))
hci_uart_set_flow_control(hu, true);
if (soc_type == QCA_WCN3990) {
@@ -1434,7 +1439,8 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
host_set_baudrate(hu, speed);
error:
- if (qca_is_wcn399x(soc_type))
+ if (qca_is_wcn399x(soc_type) ||
+ qca_is_wcn6750(soc_type))
hci_uart_set_flow_control(hu, false);
if (soc_type == QCA_WCN3990) {
@@ -1585,10 +1591,12 @@ static bool qca_prevent_wake(struct hci_dev *hdev)
return !wakeup;
}
-static int qca_wcn3990_init(struct hci_uart *hu)
+static int qca_regulator_init(struct hci_uart *hu)
{
+ enum qca_btsoc_type soc_type = qca_soc_type(hu);
struct qca_serdev *qcadev;
int ret;
+ bool sw_ctrl_state;
/* Check for vregs status, may be hci down has turned
* off the voltage regulator.
@@ -1607,16 +1615,33 @@ static int qca_wcn3990_init(struct hci_uart *hu)
}
}
- /* Forcefully enable wcn3990 to enter in to boot mode. */
- host_set_baudrate(hu, 2400);
- ret = qca_send_power_pulse(hu, false);
- if (ret)
- return ret;
+ if (qca_is_wcn399x(soc_type)) {
+ /* Forcefully enable wcn399x to enter in to boot mode. */
+ host_set_baudrate(hu, 2400);
+ ret = qca_send_power_pulse(hu, false);
+ if (ret)
+ return ret;
+ }
+
+ /* For wcn6750 need to enable gpio bt_en */
+ if (qcadev->bt_en) {
+ gpiod_set_value_cansleep(qcadev->bt_en, 0);
+ msleep(50);
+ gpiod_set_value_cansleep(qcadev->bt_en, 1);
+ msleep(50);
+ if (qcadev->sw_ctrl) {
+ sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+ bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
+ }
+ }
qca_set_speed(hu, QCA_INIT_SPEED);
- ret = qca_send_power_pulse(hu, true);
- if (ret)
- return ret;
+
+ if (qca_is_wcn399x(soc_type)) {
+ ret = qca_send_power_pulse(hu, true);
+ if (ret)
+ return ret;
+ }
/* Now the device is in ready state to communicate with host.
* To sync host with device we need to reopen port.
@@ -1649,8 +1674,9 @@ static int qca_power_on(struct hci_dev *hdev)
if (!hu->serdev)
return 0;
- if (qca_is_wcn399x(soc_type)) {
- ret = qca_wcn3990_init(hu);
+ if (qca_is_wcn399x(soc_type) ||
+ qca_is_wcn6750(soc_type)) {
+ ret = qca_regulator_init(hu);
} else {
qcadev = serdev_device_get_drvdata(hu->serdev);
if (qcadev->bt_en) {
@@ -1689,7 +1715,8 @@ static int qca_setup(struct hci_uart *hu)
set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
bt_dev_info(hdev, "setting up %s",
- qca_is_wcn399x(soc_type) ? "wcn399x" : "ROME/QCA6390");
+ qca_is_wcn399x(soc_type) ? "wcn399x" :
+ (soc_type == QCA_WCN6750) ? "wcn6750" : "ROME/QCA6390");
qca->memdump_state = QCA_MEMDUMP_IDLE;
@@ -1700,7 +1727,8 @@ static int qca_setup(struct hci_uart *hu)
clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
- if (qca_is_wcn399x(soc_type)) {
+ if (qca_is_wcn399x(soc_type) ||
+ qca_is_wcn6750(soc_type)) {
set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
ret = qca_read_soc_version(hdev, &ver, soc_type);
@@ -1720,7 +1748,8 @@ static int qca_setup(struct hci_uart *hu)
qca_baudrate = qca_get_baudrate_value(speed);
}
- if (!qca_is_wcn399x(soc_type)) {
+ if (!(qca_is_wcn399x(soc_type) ||
+ qca_is_wcn6750(soc_type))) {
/* Get QCA version information */
ret = qca_read_soc_version(hdev, &ver, soc_type);
if (ret)
@@ -1828,12 +1857,30 @@ static const struct qca_device_data qca_soc_data_qca6390 = {
.num_vregs = 0,
};
+static const struct qca_device_data qca_soc_data_wcn6750 = {
+ .soc_type = QCA_WCN6750,
+ .vregs = (struct qca_vreg []) {
+ { "vddio", 5000 },
+ { "vddaon", 26000 },
+ { "vddbtcxmx", 126000 },
+ { "vddrfacmn", 12500 },
+ { "vddrfa0p8", 102000 },
+ { "vddrfa1p7", 302000 },
+ { "vddrfa1p2", 257000 },
+ { "vddrfa2p2", 1700000 },
+ { "vddasd", 200 },
+ },
+ .num_vregs = 9,
+ .capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
+};
+
static void qca_power_shutdown(struct hci_uart *hu)
{
struct qca_serdev *qcadev;
struct qca_data *qca = hu->priv;
unsigned long flags;
enum qca_btsoc_type soc_type = qca_soc_type(hu);
+ bool sw_ctrl_state;
qcadev = serdev_device_get_drvdata(hu->serdev);
@@ -1856,6 +1903,14 @@ static void qca_power_shutdown(struct hci_uart *hu)
host_set_baudrate(hu, 2400);
qca_send_power_pulse(hu, false);
qca_regulator_disable(qcadev);
+ } else if (soc_type == QCA_WCN6750) {
+ gpiod_set_value_cansleep(qcadev->bt_en, 0);
+ msleep(100);
+ qca_regulator_disable(qcadev);
+ if (qcadev->sw_ctrl) {
+ sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+ bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
+ }
} else if (qcadev->bt_en) {
gpiod_set_value_cansleep(qcadev->bt_en, 0);
}
@@ -1978,7 +2033,9 @@ static int qca_serdev_probe(struct serdev_device *serdev)
if (!qcadev->oper_speed)
BT_DBG("UART will pick default operating speed");
- if (data && qca_is_wcn399x(data->soc_type)) {
+ if (data &&
+ (qca_is_wcn399x(data->soc_type) ||
+ qca_is_wcn6750(data->soc_type))) {
qcadev->btsoc_type = data->soc_type;
qcadev->bt_power = devm_kzalloc(&serdev->dev,
sizeof(struct qca_power),
@@ -1996,6 +2053,18 @@ static int qca_serdev_probe(struct serdev_device *serdev)
qcadev->bt_power->vregs_on = false;
+ qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
+ GPIOD_OUT_LOW);
+ if (!qcadev->bt_en && data->soc_type == QCA_WCN6750) {
+ dev_err(&serdev->dev, "failed to acquire BT_EN gpio\n");
+ power_ctrl_enabled = false;
+ }
+
+ qcadev->sw_ctrl = devm_gpiod_get_optional(&serdev->dev, "swctrl",
+ GPIOD_IN);
+ if (!qcadev->sw_ctrl && data->soc_type == QCA_WCN6750)
+ dev_warn(&serdev->dev, "failed to acquire SW_CTRL gpio\n");
+
qcadev->susclk = devm_clk_get_optional(&serdev->dev, NULL);
if (IS_ERR(qcadev->susclk)) {
dev_err(&serdev->dev, "failed to acquire clk\n");
@@ -2068,7 +2137,9 @@ static void qca_serdev_remove(struct serdev_device *serdev)
struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
struct qca_power *power = qcadev->bt_power;
- if (qca_is_wcn399x(qcadev->btsoc_type) && power->vregs_on)
+ if ((qca_is_wcn399x(qcadev->btsoc_type) ||
+ qca_is_wcn6750(qcadev->btsoc_type)) &&
+ power->vregs_on)
qca_power_shutdown(&qcadev->serdev_hu);
else if (qcadev->susclk)
clk_disable_unprepare(qcadev->susclk);
@@ -2244,6 +2315,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = {
{ .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990},
{ .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991},
{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
+ { .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 7+ messages in thread* RE: Enable Bluetooth functinality for WCN6750
2021-05-06 17:33 [PATCH v3 1/5] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750 Venkata Lakshmi Narayana Gubba
@ 2021-05-06 18:29 ` bluez.test.bot
0 siblings, 0 replies; 7+ messages in thread
From: bluez.test.bot @ 2021-05-06 18:29 UTC (permalink / raw)
To: linux-bluetooth, gubbaven
[-- Attachment #1: Type: text/plain, Size: 2709 bytes --]
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=478035
---Test result---
##############################
Test: CheckPatch - FAIL
dt-bindings: net: bluetooth: Convert Qualcomm BT binding to DT schema
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#12:
deleted file mode 100644
WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
total: 0 errors, 3 warnings, 111 lines checked
NOTE: For some of the reported defects, checkpatch may be able to
mechanically convert to the typical style using --fix or --fix-inplace.
"[PATCH] dt-bindings: net: bluetooth: Convert Qualcomm BT binding to" has style problems, please review.
NOTE: If any of the errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
##############################
Test: CheckGitLint - FAIL
Bluetooth: btqca: Add support for firmware image with mbn type for WCN6750
1: T1 Title exceeds max length (74>72): "Bluetooth: btqca: Add support for firmware image with mbn type for WCN6750"
dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
1: T1 Title exceeds max length (74>72): "dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750"
##############################
Test: CheckBuildK - PASS
##############################
Test: CheckTestRunner: Setup - PASS
##############################
Test: CheckTestRunner: l2cap-tester - PASS
Total: 40, Passed: 40 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: bnep-tester - PASS
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: mgmt-tester - PASS
Total: 416, Passed: 403 (96.9%), Failed: 0, Not Run: 13
##############################
Test: CheckTestRunner: rfcomm-tester - PASS
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: sco-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: smp-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: userchan-tester - PASS
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
[-- Attachment #2: l2cap-tester.log --]
[-- Type: application/octet-stream, Size: 44229 bytes --]
[-- Attachment #3: bnep-tester.log --]
[-- Type: application/octet-stream, Size: 3554 bytes --]
[-- Attachment #4: mgmt-tester.log --]
[-- Type: application/octet-stream, Size: 546744 bytes --]
[-- Attachment #5: rfcomm-tester.log --]
[-- Type: application/octet-stream, Size: 11676 bytes --]
[-- Attachment #6: sco-tester.log --]
[-- Type: application/octet-stream, Size: 9911 bytes --]
[-- Attachment #7: smp-tester.log --]
[-- Type: application/octet-stream, Size: 11822 bytes --]
[-- Attachment #8: userchan-tester.log --]
[-- Type: application/octet-stream, Size: 5452 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2021-05-06 18:29 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2021-03-11 16:58 [PATCH v1 0/2] Enable Bluetooth functinality for WCN6750 Venkata Lakshmi Narayana Gubba
2021-03-11 16:58 ` [PATCH v1 1/2] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750 Venkata Lakshmi Narayana Gubba
2021-03-11 17:53 ` Enable Bluetooth functinality for WCN6750 bluez.test.bot
2021-03-11 16:58 ` [PATCH v1 2/2] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750 Venkata Lakshmi Narayana Gubba
2021-03-24 15:18 ` Rob Herring
-- strict thread matches above, loose matches on Subject: below --
2021-04-20 16:26 [PATCH v2 1/3] Bluetooth: hci_qca: Add support for QTI Bluetooth " Venkata Lakshmi Narayana Gubba
2021-04-20 17:46 ` Enable Bluetooth functinality for WCN6750 bluez.test.bot
2021-05-06 17:33 [PATCH v3 1/5] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750 Venkata Lakshmi Narayana Gubba
2021-05-06 18:29 ` Enable Bluetooth functinality for WCN6750 bluez.test.bot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox