[PATCH v10 1/2] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth SoC QCA2066

[PATCH v10 1/2] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth SoC QCA2066

[Tim Jiang]

This patch adds support for QCA2066 firmware patch and NVM downloading.
as the RF performance of QCA2066 SOC chip from different foundries may
vary. Therefore we use different NVM to configure them based on board ID.

Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
---
 drivers/bluetooth/btqca.c   | 76 ++++++++++++++++++++++++++++++++++++-
 drivers/bluetooth/btqca.h   |  4 ++
 drivers/bluetooth/hci_qca.c |  8 ++++
 3 files changed, 86 insertions(+), 2 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index e7e58a956d15..834b28706d90 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -205,6 +205,46 @@ static int qca_send_reset(struct hci_dev *hdev)
 	return 0;
 }
 
+static int qca_read_fw_board_id(struct hci_dev *hdev, u16 *bid)
+{
+	u8 cmd;
+	struct sk_buff *skb;
+	struct edl_event_hdr *edl;
+	int err = 0;
+	u8 bid_len;
+
+	cmd = EDL_GET_BID_REQ_CMD;
+	skb = __hci_cmd_sync_ev(hdev, EDL_PATCH_CMD_OPCODE, EDL_PATCH_CMD_LEN,
+				&cmd, 0, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		err = PTR_ERR(skb);
+		bt_dev_err(hdev, "Reading QCA board ID failed (%d)", err);
+		return err;
+	}
+
+	edl = skb_pull_data(skb, sizeof(*edl));
+	if (!edl) {
+		bt_dev_err(hdev, "QCA read board ID with no header");
+		err = -EILSEQ;
+		goto out;
+	}
+
+	if (edl->cresp != EDL_CMD_REQ_RES_EVT ||
+	    edl->rtype != EDL_GET_BID_REQ_CMD) {
+		bt_dev_err(hdev, "QCA Wrong packet: %d %d", edl->cresp, edl->rtype);
+		err = -EIO;
+		goto out;
+	}
+
+	bid_len = edl->data[0];
+	*bid = (edl->data[1] << 8) + edl->data[2];
+	bt_dev_dbg(hdev, "%s: bid len = %x, bid = %x", __func__, bid_len, *bid);
+
+out:
+	kfree_skb(skb);
+	return err;
+}
+
 int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
 {
 	struct sk_buff *skb;
@@ -574,6 +614,29 @@ int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
 }
 EXPORT_SYMBOL_GPL(qca_set_bdaddr_rome);
 
+static void qca_generate_nvm_name(struct hci_dev *hdev, char *fwname,
+		   size_t max_size, struct qca_btsoc_version ver, u16 bid)
+{
+	u8 rom_ver;
+	u32 soc_ver;
+	const char *variant;
+
+	soc_ver = get_soc_ver(ver.soc_id, ver.rom_ver);
+	rom_ver = ((soc_ver & 0x00000f00) >> 0x04) | (soc_ver & 0x0000000f);
+
+	if ((le32_to_cpu(ver.soc_id) & 0x0000ff00) == QCA_HSP_GF_SOC_ID)  /* hsp gf chip */
+		variant = "g";
+	else
+		variant = "";
+
+	if (bid == 0x0)
+		snprintf(fwname, max_size, "qca/hpnv%02x%s.bin", rom_ver, variant);
+	else
+		snprintf(fwname, max_size, "qca/hpnv%02x%s.%x", rom_ver, variant, bid);
+
+	bt_dev_dbg(hdev, "%s: nvm name is %s", __func__, fwname);
+}
+
 int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		   enum qca_btsoc_type soc_type, struct qca_btsoc_version ver,
 		   const char *firmware_name)
@@ -582,6 +645,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	int err;
 	u8 rom_ver = 0;
 	u32 soc_ver;
+	u16 boardid = 0;
 
 	bt_dev_dbg(hdev, "QCA setup on UART");
 
@@ -604,6 +668,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	if (qca_is_wcn399x(soc_type)) {
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/crbtfw%02x.tlv", rom_ver);
+	} else if (soc_type == QCA_QCA2066) {
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/hpbtfw%02x.tlv", rom_ver);
 	} else if (soc_type == QCA_QCA6390) {
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/htbtfw%02x.tlv", rom_ver);
@@ -631,6 +698,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	/* Give the controller some time to get ready to receive the NVM */
 	msleep(10);
 
+	if (soc_type == QCA_QCA2066)
+		qca_read_fw_board_id(hdev, &boardid);
+
 	/* Download NVM configuration */
 	config.type = TLV_TYPE_NVM;
 	if (firmware_name)
@@ -644,8 +714,10 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 			snprintf(config.fwname, sizeof(config.fwname),
 				 "qca/crnv%02x.bin", rom_ver);
 		}
-	}
-	else if (soc_type == QCA_QCA6390)
+	} else if (soc_type == QCA_QCA2066) {
+		qca_generate_nvm_name(hdev, config.fwname, sizeof(config.fwname),
+				ver, boardid);
+	} else if (soc_type == QCA_QCA6390)
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/htnv%02x.bin", rom_ver);
 	else if (soc_type == QCA_WCN6750)
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index b884095bcd9d..234a97a49bb9 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -13,6 +13,7 @@
 #define EDL_PATCH_TLV_REQ_CMD		(0x1E)
 #define EDL_GET_BUILD_INFO_CMD		(0x20)
 #define EDL_NVM_ACCESS_SET_REQ_CMD	(0x01)
+#define EDL_GET_BID_REQ_CMD		(0x23)
 #define EDL_PATCH_CONFIG_CMD		(0x28)
 #define MAX_SIZE_PER_TLV_SEGMENT	(243)
 #define QCA_PRE_SHUTDOWN_CMD		(0xFC08)
@@ -48,6 +49,8 @@
 
 #define QCA_FW_BUILD_VER_LEN		255
 
+#define QCA_HSP_GF_SOC_ID		0x1200
+
 
 enum qca_baudrate {
 	QCA_BAUDRATE_115200 	= 0,
@@ -148,6 +151,7 @@ enum qca_btsoc_type {
 	QCA_QCA6390,
 	QCA_WCN6750,
 	QCA_WCN6855,
+	QCA_QCA2066,
 };
 
 #if IS_ENABLED(CONFIG_BT_QCA)
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 87a7325c75b1..c9774f7dbf24 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -1748,6 +1748,7 @@ static int qca_setup(struct hci_uart *hu)
 	const char *firmware_name = qca_get_firmware_name(hu);
 	int ret;
 	struct qca_btsoc_version ver;
+	const char *soc_name;
 
 	ret = qca_check_speeds(hu);
 	if (ret)
@@ -1913,6 +1914,11 @@ static const struct qca_device_data qca_soc_data_qca6390 __maybe_unused = {
 	.num_vregs = 0,
 };
 
+static const struct qca_device_data qca_soc_data_qca2066 __maybe_unused = {
+	.soc_type = QCA_QCA2066,
+	.num_vregs = 0,
+};
+
 static const struct qca_device_data qca_soc_data_wcn6750 __maybe_unused = {
 	.soc_type = QCA_WCN6750,
 	.vregs = (struct qca_vreg []) {
@@ -2403,6 +2409,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = {
 	{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
 	{ .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
 	{ .compatible = "qcom,wcn6855-bt", .data = &qca_soc_data_wcn6855},
+	{ .compatible = "qcom,qca2066-bt", .data = &qca_soc_data_qca2066},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
@@ -2410,6 +2417,7 @@ MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
 
 #ifdef CONFIG_ACPI
 static const struct acpi_device_id qca_bluetooth_acpi_match[] = {
+	{ "QCOM2066", (kernel_ulong_t)&qca_soc_data_qca2066 },
 	{ "QCOM6390", (kernel_ulong_t)&qca_soc_data_qca6390 },
 	{ "DLA16390", (kernel_ulong_t)&qca_soc_data_qca6390 },
 	{ "DLB16390", (kernel_ulong_t)&qca_soc_data_qca6390 },
-- 
2.41.0

[PATCH v10 2/2] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth SoC QCA2066

[Tim Jiang]

This patch make the print btsoc type expression more clearly.

Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
---
 drivers/bluetooth/hci_qca.c | 33 +++++++++++++++++++++++++++++----
 1 file changed, 29 insertions(+), 4 deletions(-)

diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index c9774f7dbf24..d90ee1ccfd9c 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -1763,10 +1763,35 @@ static int qca_setup(struct hci_uart *hu)
 	 */
 	set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
 
-	bt_dev_info(hdev, "setting up %s",
-		qca_is_wcn399x(soc_type) ? "wcn399x" :
-		(soc_type == QCA_WCN6750) ? "wcn6750" :
-		(soc_type == QCA_WCN6855) ? "wcn6855" : "ROME/QCA6390");
+	switch (soc_type) {
+	case QCA_AR3002:
+		soc_name = "ar300x";
+		break;
+	case QCA_ROME:
+		soc_name = "ROME";
+		break;
+	case QCA_WCN3990:
+	case QCA_WCN3991:
+	case QCA_WCN3998:
+		soc_name = "wcn399x";
+		break;
+	case QCA_QCA2066:
+		soc_name = "QCA2066";
+		break;
+	case QCA_QCA6390:
+		soc_name = "QCA6390";
+		break;
+	case QCA_WCN6750:
+		soc_name = "wcn6750";
+		break;
+	case QCA_WCN6855:
+		soc_name = "wcn6855";
+		break;
+	default:
+		soc_name = "unknown soc";
+		break;
+	}
+	bt_dev_info(hdev, "setting up %s", soc_name);
 
 	qca->memdump_state = QCA_MEMDUMP_IDLE;
 
-- 
2.41.0

RE: [v10,1/2] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth SoC QCA2066

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 1427 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=763866

---Test result---

Test Summary:
CheckPatch                    PASS      1.79 seconds
GitLint                       PASS      0.67 seconds
SubjectPrefix                 PASS      0.25 seconds
BuildKernel                   PASS      32.53 seconds
CheckAllWarning               PASS      35.32 seconds
CheckSparse                   PASS      40.15 seconds
CheckSmatch                   PASS      111.85 seconds
BuildKernel32                 PASS      30.83 seconds
TestRunnerSetup               PASS      475.12 seconds
TestRunner_l2cap-tester       PASS      22.12 seconds
TestRunner_iso-tester         PASS      40.87 seconds
TestRunner_bnep-tester        PASS      10.11 seconds
TestRunner_mgmt-tester        PASS      212.00 seconds
TestRunner_rfcomm-tester      PASS      15.28 seconds
TestRunner_sco-tester         PASS      16.07 seconds
TestRunner_ioctl-tester       PASS      17.17 seconds
TestRunner_mesh-tester        PASS      12.60 seconds
TestRunner_smp-tester         PASS      13.64 seconds
TestRunner_userchan-tester    PASS      10.62 seconds
IncrementalBuild              PASS      34.47 seconds



---
Regards,
Linux Bluetooth

Re: [PATCH v10 1/2] Bluetooth: hci_qca: Add support for Qualcomm Bluetooth SoC QCA2066

[Johan Hovold]

On Mon, Jul 10, 2023 at 01:59:13PM +0800, Tim Jiang wrote:
> This patch adds support for QCA2066 firmware patch and NVM downloading.
> as the RF performance of QCA2066 SOC chip from different foundries may
> vary. Therefore we use different NVM to configure them based on board ID.
> 
> Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
> ---

Again, there is still no changelog here describing what changed in each
revision of your patch as I've asked you to add. For example:

	Changes in v10
	 - break out ... into a separate patch
	 - ...
	Changes in v9
	 - ...
	...

When sending a series you should add a cover letter. The cover letter
should ideally contain the changelog for the whole series.

Also the two patches you have here should go in reverse order.

Johan