[PATCH v6 1/2] dt-bindings: net: bluetooth: nxp: Add support for 4M baudrate

[PATCH v6 1/2] dt-bindings: net: bluetooth: nxp: Add support for 4M baudrate

[Neeraj Sanjay Kale]

Add support for 4000000 as secondary baudrate for NXP chipsets
supporting max baudrate as 4M, and are close to the host processor on
same PCB. This mainly helps with faster FW download.

Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
v2: Use the available 'max-speed' device tree property. (Krzysztof)
v3: No Change
v4: Add ref for max-speed. (Krzysztof)
v5: Add ref for serial-peripheral-props.yaml. (Krzysztof)
v6: Add info to commit message. (Krzysztof)
---
 .../devicetree/bindings/net/bluetooth/nxp,88w8987-bt.yaml | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-bt.yaml b/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-bt.yaml
index 3ab60c70286f..bb9ab5dd3b4a 100644
--- a/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-bt.yaml
+++ b/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-bt.yaml
@@ -34,6 +34,13 @@ properties:
       This property depends on the module vendor's
       configuration.
 
+  max-speed:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum:
+      - 3000000
+      - 4000000
+    default: 3000000
+
   firmware-name:
     maxItems: 1
 
@@ -78,6 +85,7 @@ examples:
         bluetooth {
             compatible = "nxp,88w8987-bt";
             fw-init-baudrate = <3000000>;
+            max-speed = <4000000>;
             firmware-name = "uartuart8987_bt_v0.bin";
             device-wakeup-gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
             nxp,wakein-pin = /bits/ 8 <18>;
-- 
2.34.1

[PATCH v6 2/2] Bluetooth: btnxpuart: Add support for 4M baudrate

[Neeraj Sanjay Kale]

This adds support for 4000000 as secondary baudrate.

This value is selected from device tree property "max-speed"
which is then used to download FW chunks, and as operational baudrate after
HCI initialization is done.

Earlier, the secondary baudrate was fixed to 3000000 in driver, but now
with "max-speed" property, this secondary baudrate can be set to
4000000.

The secondary baudrate is set by the driver by sending a vendor command
(3F 09) to the firmware, with secondary baudrate parameter, in
nxp_post_init().

Any other value set for max-speed other than 3000000 or 4000000 will
default to 3000000, which is supported by all legacy and new NXP chipsets.

This feature is applicable for all new V3 bootloader chips and w8987 V1
bootloader chip.

This property does not apply for w8997 compatible device, since it
downloads a helper.bin FW file that sets secondary baudrate as 3000000
only.

The switch to 4000000 baudrate is validated using a Saleae Logic Analyzer
and imx8m-mini with AW693 M.2 module.

Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
---
v2: Change DT property to 'max-speed'. (Krzysztof)
    Add support for 4M baudrate to w8987. Update commit message.
    (Sherry)
v3: Add check for 'max-speed' and set default to 3000000. (Sherry)
    Add functional and testing details in commit message. (Paul)
v4: Add error message for invalid max-speed. (Sherry)
v5: No Change.
v6: No Change.
---
 drivers/bluetooth/btnxpuart.c | 36 ++++++++++++++++++++++++++---------
 1 file changed, 27 insertions(+), 9 deletions(-)

diff --git a/drivers/bluetooth/btnxpuart.c b/drivers/bluetooth/btnxpuart.c
index 6b13feed06df..c56b52bd8d98 100644
--- a/drivers/bluetooth/btnxpuart.c
+++ b/drivers/bluetooth/btnxpuart.c
@@ -73,7 +73,8 @@
 #define FW_AUTH_ENC		0xc0
 
 #define HCI_NXP_PRI_BAUDRATE	115200
-#define HCI_NXP_SEC_BAUDRATE	3000000
+#define HCI_NXP_SEC_BAUDRATE_3M	3000000
+#define HCI_NXP_SEC_BAUDRATE_4M	4000000
 
 #define MAX_FW_FILE_NAME_LEN    50
 
@@ -201,6 +202,7 @@ struct btnxpuart_dev {
 	u32 new_baudrate;
 	u32 current_baudrate;
 	u32 fw_init_baudrate;
+	u32 secondary_baudrate;
 	enum bootloader_param_change timeout_changed;
 	enum bootloader_param_change baudrate_changed;
 	bool helper_downloaded;
@@ -802,7 +804,10 @@ static bool nxp_fw_change_baudrate(struct hci_dev *hdev, u16 req_len)
 		nxpdev->fw_v3_offset_correction += req_len;
 	} else if (req_len == sizeof(uart_config)) {
 		uart_config.clkdiv.address = __cpu_to_le32(clkdivaddr);
-		uart_config.clkdiv.value = __cpu_to_le32(0x00c00000);
+		if (nxpdev->new_baudrate == HCI_NXP_SEC_BAUDRATE_4M)
+			uart_config.clkdiv.value = __cpu_to_le32(0x01000000);
+		else
+			uart_config.clkdiv.value = __cpu_to_le32(0x00c00000);
 		uart_config.uartdiv.address = __cpu_to_le32(uartdivaddr);
 		uart_config.uartdiv.value = __cpu_to_le32(1);
 		uart_config.mcr.address = __cpu_to_le32(uartmcraddr);
@@ -966,12 +971,13 @@ static int nxp_recv_fw_req_v1(struct hci_dev *hdev, struct sk_buff *skb)
 			goto free_skb;
 		}
 		if (nxpdev->baudrate_changed != changed) {
+			nxpdev->new_baudrate = nxpdev->secondary_baudrate;
 			if (nxp_fw_change_baudrate(hdev, len)) {
 				nxpdev->baudrate_changed = changed;
 				serdev_device_set_baudrate(nxpdev->serdev,
-							   HCI_NXP_SEC_BAUDRATE);
+							   nxpdev->secondary_baudrate);
 				serdev_device_set_flow_control(nxpdev->serdev, true);
-				nxpdev->current_baudrate = HCI_NXP_SEC_BAUDRATE;
+				nxpdev->current_baudrate = nxpdev->secondary_baudrate;
 			}
 			goto free_skb;
 		}
@@ -992,7 +998,7 @@ static int nxp_recv_fw_req_v1(struct hci_dev *hdev, struct sk_buff *skb)
 			nxpdev->helper_downloaded = true;
 			serdev_device_wait_until_sent(nxpdev->serdev, 0);
 			serdev_device_set_baudrate(nxpdev->serdev,
-						   HCI_NXP_SEC_BAUDRATE);
+						   HCI_NXP_SEC_BAUDRATE_3M);
 			serdev_device_set_flow_control(nxpdev->serdev, true);
 		} else {
 			clear_bit(BTNXPUART_FW_DOWNLOADING, &nxpdev->tx_state);
@@ -1216,12 +1222,13 @@ static int nxp_recv_fw_req_v3(struct hci_dev *hdev, struct sk_buff *skb)
 	}
 
 	if (nxpdev->baudrate_changed != changed) {
+		nxpdev->new_baudrate = nxpdev->secondary_baudrate;
 		if (nxp_fw_change_baudrate(hdev, len)) {
 			nxpdev->baudrate_changed = cmd_sent;
 			serdev_device_set_baudrate(nxpdev->serdev,
-						   HCI_NXP_SEC_BAUDRATE);
+						   nxpdev->secondary_baudrate);
 			serdev_device_set_flow_control(nxpdev->serdev, true);
-			nxpdev->current_baudrate = HCI_NXP_SEC_BAUDRATE;
+			nxpdev->current_baudrate = nxpdev->secondary_baudrate;
 		}
 		goto free_skb;
 	}
@@ -1447,8 +1454,8 @@ static int nxp_post_init(struct hci_dev *hdev)
 	struct btnxpuart_dev *nxpdev = hci_get_drvdata(hdev);
 	struct ps_data *psdata = &nxpdev->psdata;
 
-	if (nxpdev->current_baudrate != HCI_NXP_SEC_BAUDRATE) {
-		nxpdev->new_baudrate = HCI_NXP_SEC_BAUDRATE;
+	if (nxpdev->current_baudrate != nxpdev->secondary_baudrate) {
+		nxpdev->new_baudrate = nxpdev->secondary_baudrate;
 		nxp_set_baudrate_cmd(hdev, NULL);
 	}
 	if (psdata->cur_h2c_wakeupmode != psdata->h2c_wakeupmode)
@@ -1773,6 +1780,17 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
 	if (!nxpdev->fw_init_baudrate)
 		nxpdev->fw_init_baudrate = FW_INIT_BAUDRATE;
 
+	device_property_read_u32(&nxpdev->serdev->dev, "max-speed",
+				 &nxpdev->secondary_baudrate);
+	if (!nxpdev->secondary_baudrate ||
+	    (nxpdev->secondary_baudrate != HCI_NXP_SEC_BAUDRATE_3M &&
+	     nxpdev->secondary_baudrate != HCI_NXP_SEC_BAUDRATE_4M)) {
+		if (nxpdev->secondary_baudrate)
+			dev_err(&serdev->dev,
+				"Invalid max-speed. Using default 3000000.");
+		nxpdev->secondary_baudrate = HCI_NXP_SEC_BAUDRATE_3M;
+	}
+
 	set_bit(BTNXPUART_FW_DOWNLOADING, &nxpdev->tx_state);
 
 	crc8_populate_msb(crc8_table, POLYNOMIAL8);
-- 
2.34.1

RE: [v6,1/2] dt-bindings: net: bluetooth: nxp: Add support for 4M baudrate

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 1849 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=974754

---Test result---

Test Summary:
CheckPatch                    PENDING   0.45 seconds
GitLint                       PENDING   0.32 seconds
SubjectPrefix                 FAIL      0.50 seconds
BuildKernel                   PASS      24.83 seconds
CheckAllWarning               PASS      27.20 seconds
CheckSparse                   PASS      31.28 seconds
BuildKernel32                 PASS      24.61 seconds
TestRunnerSetup               PASS      478.34 seconds
TestRunner_l2cap-tester       PASS      25.08 seconds
TestRunner_iso-tester         PASS      36.12 seconds
TestRunner_bnep-tester        PASS      5.90 seconds
TestRunner_mgmt-tester        PASS      129.46 seconds
TestRunner_rfcomm-tester      PASS      9.29 seconds
TestRunner_sco-tester         PASS      14.81 seconds
TestRunner_ioctl-tester       PASS      10.10 seconds
TestRunner_mesh-tester        PASS      7.41 seconds
TestRunner_smp-tester         PASS      8.56 seconds
TestRunner_userchan-tester    PASS      6.18 seconds
IncrementalBuild              PENDING   0.56 seconds

Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script
Output:

##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:

##############################
Test: SubjectPrefix - FAIL
Desc: Check subject contains "Bluetooth" prefix
Output:
"Bluetooth: " prefix is not specified in the subject
##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series
Output:



---
Regards,
Linux Bluetooth

Re: [PATCH v6 1/2] dt-bindings: net: bluetooth: nxp: Add support for 4M baudrate

[patchwork-bot+bluetooth]

Hello:

This series was applied to bluetooth/bluetooth-next.git (master)
by Luiz Augusto von Dentz <luiz.von.dentz@intel.com>:

On Mon, 23 Jun 2025 14:43:21 +0530 you wrote:
> Add support for 4000000 as secondary baudrate for NXP chipsets
> supporting max baudrate as 4M, and are close to the host processor on
> same PCB. This mainly helps with faster FW download.
> 
> Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> 
> [...]

Here is the summary with links:
  - [v6,1/2] dt-bindings: net: bluetooth: nxp: Add support for 4M baudrate
    https://git.kernel.org/bluetooth/bluetooth-next/c/16d150e3c9a4
  - [v6,2/2] Bluetooth: btnxpuart: Add support for 4M baudrate
    https://git.kernel.org/bluetooth/bluetooth-next/c/03bddf7c2ed6

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html