* [BUG] Extended Scan Hangs
@ 2022-07-06 22:23 John Klug
2022-07-06 22:54 ` John Klug
0 siblings, 1 reply; 3+ messages in thread
From: John Klug @ 2022-07-06 22:23 UTC (permalink / raw)
To: Linux-Bluetooth MailingList
Bluez5 from master on 27 June 2022
1d6cfb8e625a944010956714c1802bc1e1fc6c4f
monitor: Fix crash when using RTT backend
Kernel:
5.4.199
After turning scan on, after a short time it hangs. Here are the packets to start discovery:
< HCI Command: LE Set Exte.. (0x08|0x0042) plen 6 #1777 [hci0] 11:06:02.731748
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4 #1778 [hci0] 11:06:02.741529
LE Set Extended Scan Enable (0x08|0x0042) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0001} [hci0] 11:06:02.741819
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 11:06:02.741899
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
After a short time and 1215 devices found (0x0012), no commands may be executed:
bluetooth]# scan off
Failed to stop discovery: org.bluez.Error.InProgress
btmon output looks stuck. Often the output stops in the middle of an event:
> HCI Event: LE Meta Event (0x3e) plen 41 #3484 [hci0] 11:06:13.493567
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0010
Props: 0x0010
Use legacy advertising PDUs
Data status: ^[[0;32mComplete^[[0m
Legacy PDU Type: ADV_NONCONN_IND (0x0010)
Address type: Random (0x01)
Address: 0C:7D:02:DB:5A:57 (Non-Resolvable)
Prima
Note that "Primary PHY" is incomplete.
The hang during scan happens 100% of the time.
John Klug
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [BUG] Extended Scan Hangs
2022-07-06 22:23 [BUG] Extended Scan Hangs John Klug
@ 2022-07-06 22:54 ` John Klug
2022-07-07 20:29 ` Luiz Augusto von Dentz
0 siblings, 1 reply; 3+ messages in thread
From: John Klug @ 2022-07-06 22:54 UTC (permalink / raw)
To: Linux-Bluetooth MailingList
I was running btmon through pcat to avoid running out of space on the device. I think this was causing packets to be cut off midstream at the end.
Here is the btmon output when turning scan off:
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0010
Props: 0x0010
Use legacy advertising PDUs
Data status: Complete
Legacy PDU Type: ADV_NONCONN_IND (0x0010)
Address type: Random (0x01)
Address: 06:62:7D:C6:64:48 (Non-Resolvable)
Primary PHY: LE 1M
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -68 dBm (0xbc)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1f
1e ff 06 00 01 09 20 02 74 f5 eb a3 76 9d e7 b5 ...... .t...v...
11 e6 85 a0 41 ca 09 4d 27 f1 f6 dc a5 5f bc ....A..M'...._.
Company: Microsoft (6)
Data: 0109200274f5eba3769de7b511e685a041ca094d27f1f6dca55fbc
@ MGMT Command: Stop Discovery (0x0024) plen 1 {0x0001} [hci0] 159.216816
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0001} [hci0] 159.220056
Stop Discovery (0x0024) plen 1
Status: Rejected (0x0b)
Address type: 0x06
LE Public
LE Random
John Klug
From: John Klug
Sent: Wednesday, July 6, 2022 5:23 PM
To: Linux-Bluetooth MailingList <linux-bluetooth@vger.kernel.org>
Subject: [BUG] Extended Scan Hangs
Bluez5 from master on 27 June 2022
1d6cfb8e625a944010956714c1802bc1e1fc6c4f
monitor: Fix crash when using RTT backend
Kernel:
5.4.199
After turning scan on, after a short time it hangs. Here are the packets to start discovery:
< HCI Command: LE Set Exte.. (0x08|0x0042) plen 6 #1777 [hci0] 11:06:02.731748
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4 #1778 [hci0] 11:06:02.741529
LE Set Extended Scan Enable (0x08|0x0042) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0001} [hci0] 11:06:02.741819
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 11:06:02.741899
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
After a short time and 1215 devices found (0x0012), no commands may be executed:
bluetooth]# scan off
Failed to stop discovery: org.bluez.Error.InProgress
btmon output looks stuck. Often the output stops in the middle of an event:
> HCI Event: LE Meta Event (0x3e) plen 41 #3484 [hci0] 11:06:13.493567
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0010
Props: 0x0010
Use legacy advertising PDUs
Data status: ^[[0;32mComplete^[[0m
Legacy PDU Type: ADV_NONCONN_IND (0x0010)
Address type: Random (0x01)
Address: 0C:7D:02:DB:5A:57 (Non-Resolvable)
Prima
Note that "Primary PHY" is incomplete.
The hang during scan happens 100% of the time.
John Klug
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [BUG] Extended Scan Hangs
2022-07-06 22:54 ` John Klug
@ 2022-07-07 20:29 ` Luiz Augusto von Dentz
0 siblings, 0 replies; 3+ messages in thread
From: Luiz Augusto von Dentz @ 2022-07-07 20:29 UTC (permalink / raw)
To: John Klug; +Cc: Linux-Bluetooth MailingList
Hi John,
On Wed, Jul 6, 2022 at 3:56 PM John Klug <John.Klug@multitech.com> wrote:
>
> I was running btmon through pcat to avoid running out of space on the device. I think this was causing packets to be cut off midstream at the end.
>
> Here is the btmon output when turning scan off:
>
> LE Extended Advertising Report (0x0d)
> Num reports: 1
> Entry 0
> Event type: 0x0010
> Props: 0x0010
> Use legacy advertising PDUs
> Data status: Complete
> Legacy PDU Type: ADV_NONCONN_IND (0x0010)
> Address type: Random (0x01)
> Address: 06:62:7D:C6:64:48 (Non-Resolvable)
> Primary PHY: LE 1M
> Secondary PHY: No packets
> SID: no ADI field (0xff)
> TX power: 127 dBm
> RSSI: -68 dBm (0xbc)
> Periodic advertising interval: 0.00 msec (0x0000)
> Direct address type: Public (0x00)
> Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
> Data length: 0x1f
> 1e ff 06 00 01 09 20 02 74 f5 eb a3 76 9d e7 b5 ...... .t...v...
> 11 e6 85 a0 41 ca 09 4d 27 f1 f6 dc a5 5f bc ....A..M'...._.
> Company: Microsoft (6)
> Data: 0109200274f5eba3769de7b511e685a041ca094d27f1f6dca55fbc
> @ MGMT Command: Stop Discovery (0x0024) plen 1 {0x0001} [hci0] 159.216816
> Address type: 0x06
> LE Public
> LE Random
> @ MGMT Event: Command Complete (0x0001) plen 4 {0x0001} [hci0] 159.220056
> Stop Discovery (0x0024) plen 1
> Status: Rejected (0x0b)
> Address type: 0x06
> LE Public
> LE Random
Looks like a bug in the kernel since it is rejecting the stop
discovery, have you checked if there are any fixes for it later on?
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-07-07 20:29 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2022-07-06 22:23 [BUG] Extended Scan Hangs John Klug
2022-07-06 22:54 ` John Klug
2022-07-07 20:29 ` Luiz Augusto von Dentz
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).