[PATCH 12/12] can: xilinx_can: fix power management handling

[Marc Kleine-Budde <mkl@pengutronix.de>]

From: Anssi Hannula <anssi.hannula@bitwise.fi>

There are several issues with the suspend/resume handling code of the
driver:

- The device is attached and detached in the runtime_suspend() and
  runtime_resume() callbacks if the interface is running. However,
  during xcan_chip_start() the interface is considered running,
  causing the resume handler to incorrectly call netif_start_queue()
  at the beginning of xcan_chip_start(), and on xcan_chip_start() error
  return the suspend handler detaches the device leaving the user
  unable to bring-up the device anymore.

- The device is not brought properly up on system resume. A reset is
  done and the code tries to determine the bus state after that.
  However, after reset the device is always in Configuration mode
  (down), so the state checking code does not make sense and
  communication will also not work.

- The suspend callback tries to set the device to sleep mode (low-power
  mode which monitors the bus and brings the device back to normal mode
  on activity), but then immediately disables the clocks (possibly
  before the device reaches the sleep mode), which does not make sense
  to me. If a clean shutdown is wanted before disabling clocks, we can
  just bring it down completely instead of only sleep mode.

Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.

The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.

xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.

Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.

Tested on Zynq-7000 integrated CAN.

Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
 drivers/net/can/xilinx_can.c | 69 +++++++++++++++---------------------
 1 file changed, 28 insertions(+), 41 deletions(-)

diff --git a/drivers/net/can/xilinx_can.c b/drivers/net/can/xilinx_can.c
index cb80a9aa7281..5a24039733ef 100644
--- a/drivers/net/can/xilinx_can.c
+++ b/drivers/net/can/xilinx_can.c
@@ -984,13 +984,9 @@ static irqreturn_t xcan_interrupt(int irq, void *dev_id)
 static void xcan_chip_stop(struct net_device *ndev)
 {
 	struct xcan_priv *priv = netdev_priv(ndev);
-	u32 ier;
 
 	/* Disable interrupts and leave the can in configuration mode */
-	ier = priv->read_reg(priv, XCAN_IER_OFFSET);
-	ier &= ~XCAN_INTR_ALL;
-	priv->write_reg(priv, XCAN_IER_OFFSET, ier);
-	priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK);
+	set_reset_mode(ndev);
 	priv->can.state = CAN_STATE_STOPPED;
 }
 
@@ -1123,10 +1119,15 @@ static const struct net_device_ops xcan_netdev_ops = {
  */
 static int __maybe_unused xcan_suspend(struct device *dev)
 {
-	if (!device_may_wakeup(dev))
-		return pm_runtime_force_suspend(dev);
+	struct net_device *ndev = dev_get_drvdata(dev);
 
-	return 0;
+	if (netif_running(ndev)) {
+		netif_stop_queue(ndev);
+		netif_device_detach(ndev);
+		xcan_chip_stop(ndev);
+	}
+
+	return pm_runtime_force_suspend(dev);
 }
 
 /**
@@ -1138,11 +1139,27 @@ static int __maybe_unused xcan_suspend(struct device *dev)
  */
 static int __maybe_unused xcan_resume(struct device *dev)
 {
-	if (!device_may_wakeup(dev))
-		return pm_runtime_force_resume(dev);
+	struct net_device *ndev = dev_get_drvdata(dev);
+	int ret;
 
-	return 0;
+	ret = pm_runtime_force_resume(dev);
+	if (ret) {
+		dev_err(dev, "pm_runtime_force_resume failed on resume\n");
+		return ret;
+	}
+
+	if (netif_running(ndev)) {
+		ret = xcan_chip_start(ndev);
+		if (ret) {
+			dev_err(dev, "xcan_chip_start failed on resume\n");
+			return ret;
+		}
 
+		netif_device_attach(ndev);
+		netif_start_queue(ndev);
+	}
+
+	return 0;
 }
 
 /**
@@ -1157,14 +1174,6 @@ static int __maybe_unused xcan_runtime_suspend(struct device *dev)
 	struct net_device *ndev = dev_get_drvdata(dev);
 	struct xcan_priv *priv = netdev_priv(ndev);
 
-	if (netif_running(ndev)) {
-		netif_stop_queue(ndev);
-		netif_device_detach(ndev);
-	}
-
-	priv->write_reg(priv, XCAN_MSR_OFFSET, XCAN_MSR_SLEEP_MASK);
-	priv->can.state = CAN_STATE_SLEEPING;
-
 	clk_disable_unprepare(priv->bus_clk);
 	clk_disable_unprepare(priv->can_clk);
 
@@ -1183,7 +1192,6 @@ static int __maybe_unused xcan_runtime_resume(struct device *dev)
 	struct net_device *ndev = dev_get_drvdata(dev);
 	struct xcan_priv *priv = netdev_priv(ndev);
 	int ret;
-	u32 isr, status;
 
 	ret = clk_prepare_enable(priv->bus_clk);
 	if (ret) {
@@ -1197,27 +1205,6 @@ static int __maybe_unused xcan_runtime_resume(struct device *dev)
 		return ret;
 	}
 
-	priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK);
-	isr = priv->read_reg(priv, XCAN_ISR_OFFSET);
-	status = priv->read_reg(priv, XCAN_SR_OFFSET);
-
-	if (netif_running(ndev)) {
-		if (isr & XCAN_IXR_BSOFF_MASK) {
-			priv->can.state = CAN_STATE_BUS_OFF;
-			priv->write_reg(priv, XCAN_SRR_OFFSET,
-					XCAN_SRR_RESET_MASK);
-		} else if ((status & XCAN_SR_ESTAT_MASK) ==
-					XCAN_SR_ESTAT_MASK) {
-			priv->can.state = CAN_STATE_ERROR_PASSIVE;
-		} else if (status & XCAN_SR_ERRWRN_MASK) {
-			priv->can.state = CAN_STATE_ERROR_WARNING;
-		} else {
-			priv->can.state = CAN_STATE_ERROR_ACTIVE;
-		}
-		netif_device_attach(ndev);
-		netif_start_queue(ndev);
-	}
-
 	return 0;
 }
 
-- 
2.18.0