messages from 2014-09-30 07:13:52 to 2014-11-03 20:47:34 UTC [more...]
[PATCH 1/7] can: m_can: fix possible sleep in napi poll
2014-11-03 20:47 UTC (20+ messages)
` [PATCH 2/7] can: m_can: fix the incorrect error messages
` [PATCH 3/7] can: m_can: add .ndo_change_mtu function
` [PATCH 4/7] can: m_can: add a bit delay after setting CCCR_INIT bit
` [PATCH 5/7] can: clear ctrlmode when close candev
` [PATCH 6/7] can: m_can: update to support CAN FD features
` [PATCH 7/7] can: m_can: workaround for transmit data less than 4 bytes
[RFC PATCH V3 00/15] CAN: Add rx-fifo support and port flexcan to it
2014-11-03 13:34 UTC (37+ messages)
` [PATCH 01/15] can: flexcan: add documentation about mailbox organizaiton
` [PATCH 02/15] can: flexcan: rename crl2 -> ctrl2
` [PATCH 03/15] can: flexcan: replace open coded mailbox code by proper defines
` [PATCH 04/15] can: flexcan: Re-write receive path to use MB queue instead of FIFO
` [PATCH 05/15] can: dev: add preliminary rx-fifo
` [PATCH 06/15] can: rx-fifo: Increase MB size limit from 32 to 64
` [PATCH 07/15] can: rx-fifo: Change to do controller off-load in interrupt and NAPI poll
` [PATCH 08/15] can: rx-fifo: fix long lines
` [PATCH 09/15] can: rx-fifo: Add can_rx_fifo_reset() function
` [PATCH 10/15] can: rx-fifo: remove obsolete comment
` [PATCH 11/15] can: rx-fifo: Add support for can state tracking and error polling
` [PATCH 12/15] can: flexcan: Add support for RX-FIFO
` [PATCH 13/15] can: rx-fifo: Add support for simple irq offloading
` [PATCH 14/15] can: flexcan: Add MB/Fifo specific column to comment table of IP versions
` [PATCH 15/15] can: flexcan: Re-enable RTR reception support for older flexcan IPs
Request for advice on CAN driver writing
2014-11-03 12:32 UTC
(unknown)
2014-11-02 19:54 UTC
[PATCH v2 1/1] can: Add support for esd CAN PCIe/402 card
2014-10-31 18:43 UTC (2+ messages)
[PATCH v5 0/2] Adding support for CAN busses via SPI interface
2014-10-31 18:23 UTC (10+ messages)
` [PATCH v5 1/2] Add documentation for SPI to CAN driver
` [PATCH v5 2/2] CAN: CAN driver to support multiple CAN bus on SPI interface
[PATCH 1/1] can: Avoid calling kfree_skb from interrupt context
2014-10-31 6:33 UTC
Calling can_free_echo_skb() from interrupt causes WARN
2014-10-30 20:37 UTC (4+ messages)
` AW: "
flexcan napi poll and error frames
2014-10-27 15:53 UTC (12+ messages)
[PATCH v2 1/4] can: dev: Consolidate and unify state change handling
2014-10-23 15:55 UTC (15+ messages)
[PATCH 1/1] can: Add support for esd CAN PCIe/402 card
2014-10-21 18:39 UTC (6+ messages)
` AW: "
` AW: "
[PATCH] net: can: esd_usb2: fix memory leak on disconnect
2014-10-18 16:48 UTC (3+ messages)
[PATCH] net: m_can: add CONFIG_HAS_IOMEM dependence
2014-10-18 16:30 UTC (2+ messages)
SocketCAN: Matlab support
2014-10-15 19:05 UTC (5+ messages)
` SocketCAN: Matlab/Simulink embedded coder support
Writing socketCAN module for my own hardware
2014-10-10 8:09 UTC (15+ messages)
[RFC V2 PATCH 1/2] can: rx-fifo: Increase MB size limit from 32 to 64
2014-10-09 12:19 UTC (3+ messages)
` [RFC V2 PATCH 2/2] can: rx-fifo: Change to do controller off-load in interrupt and NAPI poll
[PATCH v5] can: flexcan: Re-write receive path to use MB queue instead of FIFO
2014-10-09 10:37 UTC (29+ messages)
` [RFC PATCH 1/2] can: rx-fifo: Increase MB size limit from 32 to 64
` [RFC PATCH 2/2] can: rx-fifo: Add support for IRQ readout and NAPI poll
randconfig build error with next-20141001, in drivers/i2c/algos/i2c-algo-bit.c
2014-10-07 17:03 UTC (12+ messages)
` Fwd: "
[RESEND] [PATCH] net: CAN: at91_can.c: decrease likelyhood of RX overruns
2014-10-07 11:36 UTC (11+ messages)
[PATCH] drivers/net/can/m_can/Kconfig: Let CAN_M_CAN depend on HAS_IOMEM
2014-10-04 11:49 UTC (3+ messages)
[PATCH] drivers/net/can/Kconfig: Let CAN_AT91 depend on HAS_IOMEM
2014-10-02 14:01 UTC
[PATCH v2 0/3] net: can: Use syscon regmap for TI specific RAMINIT register
2014-10-01 11:11 UTC (26+ messages)
` [PATCH v2 2/3] net: can: c_can: Add syscon/regmap RAMINIT mechanism
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).