[PATCH v2 3/5] dt-bindings: media: remove support of stih407-c8sectpfe

Raphael Gallais-Pou
2025-09-12T11:37:06Z

Remove files documentation from stih407-c8sectpfe driver.

Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
---
.../admin-guide/media/platform-cardlist.rst | 2 -
.../bindings/media/stih407-c8sectpfe.txt | 88 ----------------------
2 files changed, 90 deletions(-)

diff --git a/Documentation/admin-guide/media/platform-cardlist.rst b/Documentation/admin-guide/media/platform-cardlist.rst
index 1230ae4037ad551087d4cddc8a02eab5eac2be71..63f4b19c3628f3488fd2ccd1a6dab385d46b2503 100644
--- a/Documentation/admin-guide/media/platform-cardlist.rst
+++ b/Documentation/admin-guide/media/platform-cardlist.rst
@@ -18,8 +18,6 @@ am437x-vpfe TI AM437x VPFE
aspeed-video Aspeed AST2400 and AST2500
atmel-isc ATMEL Image Sensor Controller (ISC)
atmel-isi ATMEL Image Sensor Interface (ISI)
-c8sectpfe SDR platform devices
-c8sectpfe SDR platform devices
cafe_ccic Marvell 88ALP01 (Cafe) CMOS Camera Controller
cdns-csi2rx Cadence MIPI-CSI2 RX Controller
cdns-csi2tx Cadence MIPI-CSI2 TX Controller
diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
deleted file mode 100644
index 880d4d70c9fd741ac13101721ced18f04336c373..0000000000000000000000000000000000000000
--- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
+++ /dev/null
@@ -1,88 +0,0 @@
-STMicroelectronics STi c8sectpfe binding
-============================================
-
-This document describes the c8sectpfe device bindings that is used to get transport
-stream data into the SoC on the TS pins, and into DDR for further processing.
-
-It is typically used in conjunction with one or more demodulator and tuner devices
-which converts from the RF to digital domain. Demodulators and tuners are usually
-located on an external DVB frontend card connected to SoC TS input pins.
-
-Currently 7 TS input (tsin) channels are supported on the stih407 family SoC.
-
-Required properties (controller (parent) node):
-- compatible : Should be "stih407-c8sectpfe"
-
-- reg : Address and length of register sets for each device in
- "reg-names"
-
-- reg-names : The names of the register addresses corresponding to the
- registers filled in "reg":
- - c8sectpfe: c8sectpfe registers
- - c8sectpfe-ram: c8sectpfe internal sram
-
-- clocks : phandle list of c8sectpfe clocks
-- clock-names : should be "c8sectpfe"
-See: Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-- pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
- must be defined for each tsin child node.
-- pinctrl-0 : phandle referencing pin configuration for this tsin configuration
-See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
-
-
-Required properties (tsin (child) node):
-
-- tsin-num : tsin id of the InputBlock (must be between 0 to 6)
-- i2c-bus : phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected.
-- reset-gpios : reset gpio for this tsin channel.
-
-Optional properties (tsin (child) node):
-
-- invert-ts-clk : Bool property to control sense of ts input clock (data stored on falling edge of clk).
-- serial-not-parallel : Bool property to configure input bus width (serial on ts_data<7>).
-- async-not-sync : Bool property to control if data is received in asynchronous mode
- (all bits/bytes with ts_valid or ts_packet asserted are valid).
-
-- dvb-card : Describes the NIM card connected to this tsin channel.
-
-Example:
-
-/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
-
- c8sectpfe@8a20000 {
- compatible = "st,stih407-c8sectpfe";
- reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
- reg-names = "stfe", "stfe-ram";
- interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
- interrupt-names = "stfe-error-irq", "stfe-idle-irq";
- pinctrl-0 = <&pinctrl_tsin0_serial>;
- pinctrl-1 = <&pinctrl_tsin0_parallel>;
- pinctrl-2 = <&pinctrl_tsin3_serial>;
- pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
- pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
- pinctrl-names = "tsin0-serial",
- "tsin0-parallel",
- "tsin3-serial",
- "tsin4-serial",
- "tsin5-serial";
- clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
- clock-names = "c8sectpfe";
-
- /* tsin0 is TSA on NIMA */
- tsin0: port@0 {
- tsin-num = <0>;
- serial-not-parallel;
- i2c-bus = <&ssc2>;
- reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
- dvb-card = <STV0367_TDA18212_NIMA_1>;
- };
-
- tsin3: port@3 {
- tsin-num = <3>;
- serial-not-parallel;
- i2c-bus = <&ssc3>;
- reset-gpios = <&pio15 7 GPIO_ACTIVE_HIGH>;
- dvb-card = <STV0367_TDA18212_NIMB_1>;
- };
- };

--
2.51.0