From mboxrd@z Thu Jan  1 00:00:00 1970
Return-Path: <jagan@amarulasolutions.com>
Return-Path: <jagan@amarulasolutions.com>
From: Jagan Teki <jagan@amarulasolutions.com>
To: Maxime Ripard <maxime.ripard@free-electrons.com>,
	Chen-Yu Tsai <wens@csie.org>,
	Icenowy Zheng <icenowy@aosc.io>,
	Jernej Skrabec <jernej.skrabec@siol.net>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Catalin Marinas <catalin.marinas@arm.com>,
	Will Deacon <will.deacon@arm.com>,
	David Airlie <airlied@linux.ie>,
	dri-devel@lists.freedesktop.org,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	linux-clk@vger.kernel.org,
	Michael Trimarchi <michael@amarulasolutions.com>,
	linux-arm-kernel@lists.infradead.org,
	devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	linux-sunxi@googlegroups.com
Cc: Jagan Teki <jagan@amarulasolutions.com>
Subject: [PATCH v2 24/26] arm64: dts: allwinner: a64: a64-olinuxino: Enable HDMI output
Date: Fri, 18 May 2018 15:15:34 +0530
Message-Id: <20180518094536.17201-25-jagan@amarulasolutions.com>
In-Reply-To: <20180518094536.17201-1-jagan@amarulasolutions.com>
References: <20180518094536.17201-1-jagan@amarulasolutions.com>
List-ID: <linux-clk.vger.kernel.org>

Enable HDMI output on a64-olinuxino board.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- none

 .../boot/dts/allwinner/sun50i-a64-olinuxino.dts    | 26 ++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
index 3b3081b10ecb..83329c8fec4f 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
@@ -58,12 +58,38 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 	};
 };
 
+&de {
+	status = "okay";
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-- 
2.14.3