Re: [RFC PATCH v5 6/9] media: tegra: Add Tegra210 Video input driver

Hans Verkuil
2020-03-30T10:59:31Z

On 3/25/20 12:03 PM, Sakari Ailus wrote:
> Hi Sowjanya,
>
> Thanks for the patchset.
>
> On Mon, Mar 23, 2020 at 10:52:32AM -0700, Sowjanya Komatineni wrote:
>> Tegra210 contains a powerful Video Input (VI) hardware controller
>> which can support up to 6 MIPI CSI camera sensors.
>>
>> Each Tegra CSI port can be one-to-one mapped to VI channel and can
>> capture from an external camera sensor connected to CSI or from
>> built-in test pattern generator.
>>
>> Tegra210 supports built-in test pattern generator from CSI to VI.
>>
>> This patch adds a V4L2 media controller and capture driver support
>> for Tegra210 built-in CSI to VI test pattern generator.
>>
>> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
>> ---
>> drivers/staging/media/Kconfig | 2 +
>> drivers/staging/media/Makefile | 1 +
>> drivers/staging/media/tegra/Kconfig | 10 +
>> drivers/staging/media/tegra/Makefile | 8 +
>> drivers/staging/media/tegra/TODO | 10 +
>> drivers/staging/media/tegra/tegra-common.h | 263 +++++++
>> drivers/staging/media/tegra/tegra-csi.c | 522 ++++++++++++++
>> drivers/staging/media/tegra/tegra-csi.h | 118 ++++
>> drivers/staging/media/tegra/tegra-vi.c | 1058 ++++++++++++++++++++++++++++
>> drivers/staging/media/tegra/tegra-vi.h | 83 +++
>> drivers/staging/media/tegra/tegra-video.c | 129 ++++
>> drivers/staging/media/tegra/tegra-video.h | 32 +
>> drivers/staging/media/tegra/tegra210.c | 754 ++++++++++++++++++++
>> drivers/staging/media/tegra/tegra210.h | 192 +++++
>
> Why staging? Are there reasons not to aim this to the kernel proper right
> away? If you only support TPG, the driver may not have too many (if any)
> real users anyway.
>
>> 14 files changed, 3182 insertions(+)
>> create mode 100644 drivers/staging/media/tegra/Kconfig
>> create mode 100644 drivers/staging/media/tegra/Makefile
>> create mode 100644 drivers/staging/media/tegra/TODO
>> create mode 100644 drivers/staging/media/tegra/tegra-common.h
>> create mode 100644 drivers/staging/media/tegra/tegra-csi.c
>> create mode 100644 drivers/staging/media/tegra/tegra-csi.h
>> create mode 100644 drivers/staging/media/tegra/tegra-vi.c
>> create mode 100644 drivers/staging/media/tegra/tegra-vi.h
>> create mode 100644 drivers/staging/media/tegra/tegra-video.c
>> create mode 100644 drivers/staging/media/tegra/tegra-video.h
>> create mode 100644 drivers/staging/media/tegra/tegra210.c
>> create mode 100644 drivers/staging/media/tegra/tegra210.h
>>

<snip>

>> +static int tegra_channel_g_input(struct file *file, void *priv,
>> + unsigned int *i)
>> +{
>> + *i = 0;
>> + return 0;
>> +}
>> +
>> +static int tegra_channel_s_input(struct file *file, void *priv,
>> + unsigned int input)
>> +{
>> + if (input > 0)
>> + return -EINVAL;
>> +
>> + return 0;
>> +}
>
> Please see patchset on topic "v4l2-dev/ioctl: Add V4L2_CAP_IO_MC" on
> linux-media; it's relevant here, too.

No, it isn't. The pipeline is controlled by the driver, not by userspace.
This is a regular video capture driver, not an ISP driver.

<snip>

>> +static int tegra_channel_init(struct tegra_vi_channel *chan)
>> +{
>> + struct tegra_vi *vi = chan->vi;
>> + struct tegra_video_device *vid = dev_get_drvdata(vi->client.host);
>> + unsigned long flags = HOST1X_SYNCPT_CLIENT_MANAGED;
>> + int ret;
>> +
>> + mutex_init(&chan->video_lock);
>
> Also remember mutex_destroy().
>
>> + INIT_LIST_HEAD(&chan->capture);
>> + INIT_LIST_HEAD(&chan->done);
>> + spin_lock_init(&chan->start_lock);
>> + spin_lock_init(&chan->done_lock);
>> + init_waitqueue_head(&chan->start_wait);
>> + init_waitqueue_head(&chan->done_wait);
>> +
>> + /* initialize the video format */
>> + chan->fmtinfo = &tegra_default_format;
>> + chan->format.pixelformat = chan->fmtinfo->fourcc;
>> + chan->format.colorspace = V4L2_COLORSPACE_SRGB;
>> + chan->format.field = V4L2_FIELD_NONE;
>> + chan->format.width = TEGRA_DEF_WIDTH;
>> + chan->format.height = TEGRA_DEF_HEIGHT;
>> + chan->format.bytesperline = TEGRA_DEF_WIDTH * chan->fmtinfo->bpp;
>> + chan->format.sizeimage = chan->format.bytesperline * TEGRA_DEF_HEIGHT;
>> + tegra_channel_fmt_align(chan, &chan->format, chan->fmtinfo->bpp);
>> +
>> + chan->video = video_device_alloc();
>
> No need to allocate separately; put this into e.g. struct tegra_vi_channel.
>
>> + if (!chan->video) {
>> + dev_err(vi->dev, "unable to allocate video device\n");
>> + return -ENOMEM;
>> + }
>> +
>> + /* initialize the media entity */
>> + chan->pad.flags = MEDIA_PAD_FL_SINK;
>> + ret = media_entity_pads_init(&chan->video->entity, 1, &chan->pad);
>> + if (ret < 0) {
>> + dev_err(vi->dev,
>> + "failed to initialize media entity: %d\n", ret);
>> + goto release_vdev;
>> + }
>> +
>> + ret = v4l2_ctrl_handler_init(&chan->ctrl_handler, MAX_CID_CONTROLS);
>> + if (chan->ctrl_handler.error) {
>> + dev_err(vi->dev,
>> + "failed to initialize v4l2 ctrl handler: %d\n", ret);
>> + goto cleanup_media;
>> + }
>> +
>> + /* initialize the video_device */
>> + chan->video->fops = &tegra_channel_fops;
>> + chan->video->v4l2_dev = &vid->v4l2_dev;
>> + chan->video->release = video_device_release_empty;
>> + chan->video->queue = &chan->queue;
>> + snprintf(chan->video->name, sizeof(chan->video->name), "%s-%s-%u",
>> + dev_name(vi->dev), "output", chan->portno);
>> + chan->video->vfl_type = VFL_TYPE_VIDEO;
>> + chan->video->vfl_dir = VFL_DIR_RX;
>> + chan->video->ioctl_ops = &tegra_channel_ioctl_ops;
>> + chan->video->ctrl_handler = &chan->ctrl_handler;
>> + chan->video->lock = &chan->video_lock;
>> + chan->video->device_caps = V4L2_CAP_VIDEO_CAPTURE |
>> + V4L2_CAP_STREAMING |
>> + V4L2_CAP_READWRITE;
>> + video_set_drvdata(chan->video, chan);
>> +
>> + chan->frame_start_sp = host1x_syncpt_request(&vi->client, flags);
>> + if (!chan->frame_start_sp) {
>> + dev_err(vi->dev, "failed to request frame start syncpoint\n");
>> + ret = -ENOMEM;
>> + goto free_v4l2_ctrl_hdl;
>> + }
>> +
>> + chan->mw_ack_sp = host1x_syncpt_request(&vi->client, flags);
>> + if (!chan->mw_ack_sp) {
>> + dev_err(vi->dev, "failed to request memory ack syncpoint\n");
>> + ret = -ENOMEM;
>> + goto free_fs_syncpt;
>> + }
>> +
>> + chan->queue.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
>> + chan->queue.io_modes = VB2_MMAP | VB2_DMABUF | VB2_READ;
>> + chan->queue.lock = &chan->video_lock;
>> + chan->queue.drv_priv = chan;
>> + chan->queue.buf_struct_size = sizeof(struct tegra_channel_buffer);
>> + chan->queue.ops = &tegra_channel_queue_qops;
>> + chan->queue.min_buffers_needed = 3;
>> + chan->queue.mem_ops = &vb2_dma_contig_memops;
>> + chan->queue.timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
>> + chan->queue.dev = vi->dev;
>> + ret = vb2_queue_init(&chan->queue);
>> + if (ret < 0) {
>> + dev_err(vi->dev, "failed to initialize vb2 queue: %d\n", ret);
>> + goto free_mw_ack_syncpt;
>> + }
>> +
>> + ret = video_register_device(chan->video, VFL_TYPE_VIDEO, -1);
>> + if (ret < 0) {
>> + dev_err(vi->dev, "failed to register video device: %d\n", ret);
>> + goto rel_vb2_queue;
>> + }
>> +
>> + return 0;
>> +
>> +rel_vb2_queue:
>> + vb2_queue_release(&chan->queue);
>> +free_mw_ack_syncpt:
>> + host1x_syncpt_free(chan->mw_ack_sp);
>> +free_fs_syncpt:
>> + host1x_syncpt_free(chan->frame_start_sp);
>> +free_v4l2_ctrl_hdl:
>> + v4l2_ctrl_handler_free(&chan->ctrl_handler);
>> +cleanup_media:
>> + media_entity_cleanup(&chan->video->entity);
>> +release_vdev:
>> + video_device_release(chan->video);
>> + return ret;
>> +}
>> +
>> +static int tegra_vi_tpg_channels_alloc(struct tegra_vi *vi)
>> +{
>> + struct tegra_vi_channel *chan, *tmp;
>> + unsigned int port_num;
>> + unsigned int nchannels = vi->soc->vi_max_channels;
>> + int ret = 0;
>> +
>> + for (port_num = 0; port_num < nchannels; port_num++) {
>> + chan = kzalloc(sizeof(*chan), GFP_KERNEL);
>> + if (!chan) {
>> + ret = -ENOMEM;
>> + goto cleanup;
>> + }
>> +
>> + chan->vi = vi;
>> + chan->portno = port_num;
>> + list_add_tail(&chan->list, &vi->vi_chans);
>> + }
>> +
>> + return 0;
>> +
>> +cleanup:
>> + list_for_each_entry_safe(chan, tmp, &vi->vi_chans, list) {
>> + list_del(&chan->list);
>> + kfree(chan);
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int tegra_vi_channels_init(struct tegra_vi *vi)
>> +{
>> + struct tegra_vi_channel *chan;
>> + int ret;
>> +
>> + list_for_each_entry(chan, &vi->vi_chans, list) {
>> + ret = tegra_channel_init(chan);
>> + if (ret < 0) {
>> + dev_err(vi->dev, "channel %d init failed: %d\n",
>> + chan->portno, ret);
>> + return ret;
>> + }
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void tegra_vi_channels_cleanup(struct tegra_vi *vi)
>> +{
>> + struct tegra_vi_channel *chan, *tmp;
>> +
>> + list_for_each_entry_safe(chan, tmp, &vi->vi_chans, list) {
>> + if (chan->video) {
>> + video_unregister_device(chan->video);
>> + mutex_lock(&chan->video_lock);
>> + vb2_queue_release(&chan->queue);
>> + mutex_unlock(&chan->video_lock);
>> + video_device_release(chan->video);
>> + }
>> +
>> + if (chan->frame_start_sp)
>> + host1x_syncpt_free(chan->frame_start_sp);
>> +
>> + if (chan->mw_ack_sp)
>> + host1x_syncpt_free(chan->mw_ack_sp);
>> +
>> + v4l2_ctrl_handler_free(&chan->ctrl_handler);
>> +
>> + list_del(&chan->list);
>> + kfree(chan);
>> + }
>> +}
>> +
>> +static int tegra_vi_tpg_graph_init(struct tegra_vi *vi)
>> +{
>> + struct tegra_video_device *vid = dev_get_drvdata(vi->client.host);
>> + struct tegra_csi *csi = vid->csi;
>> + struct tegra_vi_channel *vi_chan;
>> + struct tegra_csi_channel *csi_chan;
>> + u32 link_flags = MEDIA_LNK_FL_ENABLED;
>> + int ret = 0;
>> +
>> + csi_chan = list_first_entry(&csi->csi_chans, struct tegra_csi_channel,
>> + list);
>> +
>> + list_for_each_entry(vi_chan, &vi->vi_chans, list) {
>> + struct media_entity *source = &csi_chan->subdev.entity;
>> + struct media_entity *sink = &vi_chan->video->entity;
>> + struct media_pad *source_pad = csi_chan->pads;
>> + struct media_pad *sink_pad = &vi_chan->pad;
>> +
>> + ret = v4l2_device_register_subdev(&vid->v4l2_dev,
>> + &csi_chan->subdev);
>
> Please first create the links, then register the subdev.
>
> Where is the corresponding media entity initialised?
>
>> + if (ret) {
>> + dev_err(vi->dev,
>> + "failed to register subdev: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + dev_dbg(vi->dev, "creating %s:%u -> %s:%u link\n",
>> + source->name, source_pad->index,
>> + sink->name, sink_pad->index);
>> +
>> + ret = media_create_pad_link(source, source_pad->index,
>> + sink, sink_pad->index,
>> + link_flags);
>> + if (ret < 0) {
>> + dev_err(vi->dev,
>> + "failed to create %s:%u -> %s:%u link: %d\n",
>> + source->name, source_pad->index,
>> + sink->name, sink_pad->index, ret);
>> + return ret;
>> + }
>> +
>> + vi_tpg_fmts_bitmap_init(vi_chan);
>> + tegra_channel_setup_ctrl_handler(vi_chan);
>> + csi_chan = list_next_entry(csi_chan, list);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void tegra_vi_tpg_graph_cleanup(struct tegra_vi *vi)
>> +{
>> + struct tegra_video_device *vid = dev_get_drvdata(vi->client.host);
>> + struct tegra_csi *csi = vid->csi;
>> + struct tegra_csi_channel *csi_chan;
>> +
>> + list_for_each_entry(csi_chan, &csi->csi_chans, list)
>> + v4l2_device_unregister_subdev(&csi_chan->subdev);
>> +}
>> +
>> +static int tegra_vi_init(struct host1x_client *client)
>> +{
>> + struct tegra_video_device *vid = dev_get_drvdata(client->host);
>> + struct tegra_vi *vi = host1x_client_to_vi(client);
>> + int ret;
>> +
>> + vid->vi = vi;
>> + vid->media_dev.hw_revision = vi->soc->hw_revision;
>> + snprintf(vid->media_dev.bus_info, sizeof(vid->media_dev.bus_info),
>> + "platform:%s", dev_name(vi->dev));
>> +
>> + if (!vid->csi) {
>> + dev_err(vi->dev, "csi host1x client is not initialized\n");
>> + return -ENODEV;
>> + }
>> +
>> + INIT_LIST_HEAD(&vi->vi_chans);
>> +
>> + ret = tegra_vi_tpg_channels_alloc(vi);
>> + if (ret < 0)
>> + return ret;
>> +
>> + ret = tegra_vi_channels_init(vi);
>> + if (ret < 0)
>> + goto cleanup;
>> +
>> + ret = pm_runtime_get_sync(vi->dev);
>> + if (ret < 0) {
>> + dev_err(vi->dev, "runtime resume failed: %d\n", ret);
>> + goto cleanup;
>
> s/cleanup/rpm_put/
>
>> + }
>> +
>> + /* setup media links between Tegra VI and CSI for TPG */
>> + ret = tegra_vi_tpg_graph_init(vi);
>> + if (ret < 0)
>> + goto rpm_put;
>> +
>> + return 0;
>> +
>> +rpm_put:
>> + pm_runtime_put_sync(vi->dev);
>> +cleanup:
>> + tegra_vi_channels_cleanup(vi);
>> + return ret;
>> +}
>> +
>> +static int tegra_vi_exit(struct host1x_client *client)
>> +{
>> + struct tegra_video_device *vid = dev_get_drvdata(client->host);
>> + struct tegra_vi *vi = vid->vi;
>> +
>> + if (!vid->vi)
>> + return 0;
>> +
>> + tegra_vi_channels_cleanup(vi);
>> + tegra_vi_tpg_graph_cleanup(vi);
>> + pm_runtime_put_sync(vi->dev);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct host1x_client_ops vi_client_ops = {
>> + .init = tegra_vi_init,
>> + .exit = tegra_vi_exit,
>> +};
>> +
>> +static int tegra_vi_probe(struct platform_device *pdev)
>> +{
>> + struct resource *res;
>> + struct tegra_vi *vi;
>> + int ret;
>> +
>> + vi = kzalloc(sizeof(*vi), GFP_KERNEL);
>
> You could use devm_kzalloc(), and not worry about freeing it.

That would likely fail if the driver is unbound.

Regards,

Hans

>
>> + if (!vi)
>> + return -ENOMEM;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + vi->iomem = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(vi->iomem)) {
>> + ret = PTR_ERR(vi->iomem);
>> + goto cleanup;
>> + }
>> +
>> + vi->soc = of_device_get_match_data(&pdev->dev);
>> + if (!vi->soc) {
>> + ret = -ENODATA;
>> + goto cleanup;
>> + }
>> +
>> + vi->vi_clk = devm_clk_get(&pdev->dev, "vi");
>> + if (IS_ERR(vi->vi_clk)) {
>> + ret = PTR_ERR(vi->vi_clk);
>> + dev_err(&pdev->dev, "failed to get vi clock: %d\n", ret);
>> + goto cleanup;
>> + }
>> +
>> + vi->vi_reg = devm_regulator_get(&pdev->dev, "avdd-dsi-csi");
>> + if (IS_ERR(vi->vi_reg)) {
>> + ret = PTR_ERR(vi->vi_reg);
>> + dev_err(&pdev->dev, "failed to get VDD supply: %d\n", ret);
>> + goto cleanup;
>> + }
>> +
>> + if (!pdev->dev.pm_domain) {
>> + ret = -ENOENT;
>> + dev_warn(&pdev->dev, "PM domain is not attached: %d\n", ret);
>> + goto cleanup;
>> + }
>> +
>> + ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
>> + if (ret) {
>> + dev_err(&pdev->dev,
>> + "failed to populate vi child device: %d\n", ret);
>> + goto cleanup;
>> + }
>> +
>> + vi->dev = &pdev->dev;
>> + vi->ops = vi->soc->ops;
>> + platform_set_drvdata(pdev, vi);
>> + pm_runtime_enable(&pdev->dev);
>> +
>> + /* initialize host1x interface */
>> + INIT_LIST_HEAD(&vi->client.list);
>> + vi->client.ops = &vi_client_ops;
>> + vi->client.dev = &pdev->dev;
>> +
>> + ret = host1x_client_register(&vi->client);
>> + if (ret < 0) {
>> + dev_err(vi->dev,
>> + "failed to register host1x client: %d\n", ret);
>> + ret = -ENODEV;
>> + goto rpm_disable;
>> + }
>> +
>> + return 0;
>> +
>> +rpm_disable:
>> + pm_runtime_disable(&pdev->dev);
>> + of_platform_depopulate(vi->dev);
>> +cleanup:
>> + kfree(vi);
>> + return ret;
>> +}
>> +
>> +static int tegra_vi_remove(struct platform_device *pdev)
>> +{
>> + struct tegra_vi *vi = platform_get_drvdata(pdev);
>> + int err;
>> +
>> + pm_runtime_disable(vi->dev);
>
> Does this driver work without runtime PM (CONFIG_PM nowadays)?
>
>> +
>> + err = host1x_client_unregister(&vi->client);
>> + if (err < 0) {
>> + dev_err(vi->dev,
>> + "failed to unregister host1x client: %d\n", err);
>> + return err;
>> + }
>> +
>> + of_platform_depopulate(vi->dev);
>> + kfree(vi);
>> +
>> + return 0;
>> +}
>> +
>> +static int vi_runtime_resume(struct device *dev)
>> +{
>> + struct tegra_vi *vi = dev_get_drvdata(dev);
>> + int ret;
>> +
>> + ret = regulator_enable(vi->vi_reg);
>> + if (ret) {
>> + dev_err(dev, "failed to enable VDD supply: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + ret = clk_set_rate(vi->vi_clk, vi->soc->vi_max_clk_hz);
>> + if (ret) {
>> + dev_err(dev, "failed to set vi clock rate: %d\n", ret);
>> + goto disable_vi_reg;
>> + }
>> +
>> + ret = clk_prepare_enable(vi->vi_clk);
>> + if (ret) {
>> + dev_err(dev, "failed to enable vi clock: %d\n", ret);
>> + goto disable_vi_reg;
>> + }
>> +
>> + return 0;
>> +
>> +disable_vi_reg:
>> + regulator_disable(vi->vi_reg);
>> + return ret;
>> +}
>> +
>> +static int vi_runtime_suspend(struct device *dev)
>> +{
>> + struct tegra_vi *vi = dev_get_drvdata(dev);
>> +
>> + clk_disable_unprepare(vi->vi_clk);
>> + regulator_disable(vi->vi_reg);
>> +
>> + return 0;
>> +}
>> +
>> +/* Tegra supported video formats */
>> +const struct tegra_video_format tegra210_video_formats[] = {
>> + /* RAW 8 */
>> + TEGRA_VIDEO_FORMAT(RAW8, 8, SRGGB8_1X8, 1, T_L8, SRGGB8),
>> + TEGRA_VIDEO_FORMAT(RAW8, 8, SGRBG8_1X8, 1, T_L8, SGRBG8),
>> + TEGRA_VIDEO_FORMAT(RAW8, 8, SGBRG8_1X8, 1, T_L8, SGBRG8),
>> + TEGRA_VIDEO_FORMAT(RAW8, 8, SBGGR8_1X8, 1, T_L8, SBGGR8),
>> + /* RAW 10 */
>> + TEGRA_VIDEO_FORMAT(RAW10, 10, SRGGB10_1X10, 2, T_R16_I, SRGGB10),
>> + TEGRA_VIDEO_FORMAT(RAW10, 10, SGRBG10_1X10, 2, T_R16_I, SGRBG10),
>> + TEGRA_VIDEO_FORMAT(RAW10, 10, SGBRG10_1X10, 2, T_R16_I, SGBRG10),
>> + TEGRA_VIDEO_FORMAT(RAW10, 10, SBGGR10_1X10, 2, T_R16_I, SBGGR10),
>> + /* RAW 12 */
>> + TEGRA_VIDEO_FORMAT(RAW12, 12, SRGGB12_1X12, 2, T_R16_I, SRGGB12),
>> + TEGRA_VIDEO_FORMAT(RAW12, 12, SGRBG12_1X12, 2, T_R16_I, SGRBG12),
>> + TEGRA_VIDEO_FORMAT(RAW12, 12, SGBRG12_1X12, 2, T_R16_I, SGBRG12),
>> + TEGRA_VIDEO_FORMAT(RAW12, 12, SBGGR12_1X12, 2, T_R16_I, SBGGR12),
>> + /* RGB888 */
>> + TEGRA_VIDEO_FORMAT(RGB888, 24, RGB888_1X24, 4, T_A8R8G8B8, RGB24),
>> + TEGRA_VIDEO_FORMAT(RGB888, 24, RGB888_1X32_PADHI, 4, T_A8B8G8R8,
>> + XBGR32),
>> + /* YUV422 */
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, UYVY8_1X16, 2, T_U8_Y8__V8_Y8, UYVY),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, VYUY8_1X16, 2, T_V8_Y8__U8_Y8, VYUY),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, YUYV8_1X16, 2, T_Y8_U8__Y8_V8, YUYV),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, YVYU8_1X16, 2, T_Y8_V8__Y8_U8, YVYU),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, UYVY8_1X16, 1, T_Y8__V8U8_N422, NV16),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, UYVY8_2X8, 2, T_U8_Y8__V8_Y8, UYVY),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, VYUY8_2X8, 2, T_V8_Y8__U8_Y8, VYUY),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, YUYV8_2X8, 2, T_Y8_U8__Y8_V8, YUYV),
>> + TEGRA_VIDEO_FORMAT(YUV422_8, 16, YVYU8_2X8, 2, T_Y8_V8__Y8_U8, YVYU),
>> +};
>> +
>> +static const struct tegra_vi_ops tegra210_vi_ops = {
>> + .vi_start_streaming = tegra210_vi_start_streaming,
>> + .vi_stop_streaming = tegra210_vi_stop_streaming,
>> +};
>> +
>> +static const struct tegra_vi_soc tegra210_vi_soc = {
>> + .video_formats = tegra210_video_formats,
>> + .nformats = ARRAY_SIZE(tegra210_video_formats),
>> + .ops = &tegra210_vi_ops,
>> + .hw_revision = 3,
>> + .vi_max_channels = 6,
>> + .vi_max_clk_hz = 499200000,
>> +};
>> +
>> +static const struct of_device_id tegra_vi_of_id_table[] = {
>> + { .compatible = "nvidia,tegra210-vi", .data = &tegra210_vi_soc },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(of, tegra_vi_of_id_table);
>> +
>> +static const struct dev_pm_ops tegra_vi_pm_ops = {
>> + SET_RUNTIME_PM_OPS(vi_runtime_suspend, vi_runtime_resume, NULL)
>> +};
>> +
>> +struct platform_driver tegra_vi_driver = {
>> + .driver = {
>> + .name = "tegra-vi",
>> + .of_match_table = tegra_vi_of_id_table,
>> + .pm = &tegra_vi_pm_ops,
>> + },
>> + .probe = tegra_vi_probe,
>> + .remove = tegra_vi_remove,
>> +};
>> +
>> +MODULE_AUTHOR("Sowjanya Komatineni <skomatineni@nvidia.com>");
>> +MODULE_DESCRIPTION("NVIDIA Tegra Video Input Device Driver");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/staging/media/tegra/tegra-vi.h b/drivers/staging/media/tegra/tegra-vi.h
>> new file mode 100644
>> index 0000000..d639b36
>> --- /dev/null
>> +++ b/drivers/staging/media/tegra/tegra-vi.h
>> @@ -0,0 +1,83 @@
>> +/* SPDX-License-Identifier: GPL-2.0-only */
>> +/*
>> + * Copyright (C) 2020 NVIDIA CORPORATION. All rights reserved.
>> + */
>> +
>> +#ifndef __TEGRA_VI_H__
>> +#define __TEGRA_VI_H__
>> +
>> +#include <linux/host1x.h>
>> +#include <linux/list.h>
>> +#include <linux/mutex.h>
>> +#include <linux/spinlock.h>
>> +#include <linux/videodev2.h>
>> +
>> +#include <media/media-device.h>
>> +#include <media/media-entity.h>
>> +#include <media/v4l2-async.h>
>> +#include <media/v4l2-ctrls.h>
>> +#include <media/v4l2-device.h>
>> +#include <media/v4l2-dev.h>
>> +#include <media/videobuf2-v4l2.h>
>> +
>> +#include "tegra-common.h"
>> +
>> +/**
>> + * struct tegra_vi_ops - Tegra VI operations
>> + * @vi_start_streaming: starts media pipeline, subdevice streaming, sets up
>> + * VI for capture and runs capture start and capture finish
>> + * kthreads for capturing frames to buffer and returns them back.
>> + * @vi_stop_streaming: stops media pipeline and subdevice streaming and returns
>> + * back any queued buffers.
>> + */
>> +struct tegra_vi_ops {
>> + int (*vi_start_streaming)(struct vb2_queue *vq, u32 count);
>> + void (*vi_stop_streaming)(struct vb2_queue *vq);
>> +};
>> +
>> +/**
>> + * struct tegra_vi_soc - NVIDIA Tegra Video Input SoC structure
>> + *
>> + * @video_formats: supported video formats
>> + * @nformats: total video formats
>> + * @ops: vi operations
>> + * @hw_revision: VI hw_revision
>> + * @vi_max_channels: supported max streaming channels
>> + * @vi_max_clk_hz: VI clock max frequency
>> + */
>> +struct tegra_vi_soc {
>> + const struct tegra_video_format *video_formats;
>> + const unsigned int nformats;
>> + const struct tegra_vi_ops *ops;
>> + u32 hw_revision;
>> + unsigned int vi_max_channels;
>> + unsigned int vi_max_clk_hz;
>> +};
>> +
>> +/**
>> + * struct tegra_vi - NVIDIA Tegra Video Input device structure
>> + *
>> + * @dev: device struct
>> + * @client: host1x_client struct
>> + * @iomem: register base
>> + * @vi_clk: main clock for VI block
>> + * @vi_reg: regulator for VI hardware, normally it avdd_dsi_csi
>> + * @soc: pointer to SoC data structure
>> + * @ops: vi operations
>> + * @vi_chans: list head for VI channels
>> + */
>> +struct tegra_vi {
>> + struct device *dev;
>> + struct host1x_client client;
>> + void __iomem *iomem;
>> + struct clk *vi_clk;
>> + struct regulator *vi_reg;
>> + const struct tegra_vi_soc *soc;
>> + const struct tegra_vi_ops *ops;
>> + struct list_head vi_chans;
>> +};
>> +
>> +void tegra210_vi_stop_streaming(struct vb2_queue *vq);
>> +int tegra210_vi_start_streaming(struct vb2_queue *vq, u32 count);
>> +
>> +#endif /* __TEGRA_VI_H__ */
>> diff --git a/drivers/staging/media/tegra/tegra-video.c b/drivers/staging/media/tegra/tegra-video.c
>> new file mode 100644
>> index 0000000..bd3718e
>> --- /dev/null
>> +++ b/drivers/staging/media/tegra/tegra-video.c
>> @@ -0,0 +1,129 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * Copyright (C) 2020 NVIDIA CORPORATION. All rights reserved.
>> + */
>> +
>> +#include <linux/host1x.h>
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +
>> +#include "tegra-video.h"
>> +
>> +static void tegra_v4l2_dev_release(struct v4l2_device *v4l2_dev)
>> +{
>> + struct tegra_video_device *vid;
>> +
>> + vid = container_of(v4l2_dev, struct tegra_video_device, v4l2_dev);
>> + v4l2_device_unregister(v4l2_dev);
>> + kfree(vid);
>> +}
>> +
>> +static int host1x_video_probe(struct host1x_device *dev)
>> +{
>> + struct tegra_video_device *vid;
>> + int ret;
>> +
>> + vid = kzalloc(sizeof(*vid), GFP_KERNEL);
>> + if (!vid)
>> + return -ENOMEM;
>> +
>> + vid->media_dev.dev = get_device(&dev->dev);
>> + strscpy(vid->media_dev.model, "NVIDIA Tegra Video Input Device",
>> + sizeof(vid->media_dev.model));
>> +
>> + media_device_init(&vid->media_dev);
>> + ret = media_device_register(&vid->media_dev);
>> + if (ret < 0) {
>> + dev_err(vid->media_dev.dev,
>> + "failed to register media device: %d\n", ret);
>> + goto cleanup;
>> + }
>> +
>> + vid->v4l2_dev.mdev = &vid->media_dev;
>> + vid->v4l2_dev.release = tegra_v4l2_dev_release;
>> + dev_set_drvdata(&dev->dev, vid);
>> + ret = v4l2_device_register(vid->media_dev.dev, &vid->v4l2_dev);
>> + if (ret < 0) {
>> + dev_err(vid->media_dev.dev,
>> + "V4L2 device registration failed: %d\n", ret);
>> + goto unregister_media;
>> + }
>> +
>> + ret = host1x_device_init(dev);
>> + if (ret < 0)
>> + goto unregister_v4l2;
>> +
>> + return 0;
>> +
>> +unregister_v4l2:
>> + v4l2_device_unregister(&vid->v4l2_dev);
>> +unregister_media:
>> + media_device_unregister(&vid->media_dev);
>> +cleanup:
>> + media_device_cleanup(&vid->media_dev);
>> + kfree(vid);
>> + return ret;
>> +}
>> +
>> +static int host1x_video_remove(struct host1x_device *dev)
>> +{
>> + struct tegra_video_device *vid = dev_get_drvdata(&dev->dev);
>> +
>> + host1x_device_exit(dev);
>> + media_device_unregister(&vid->media_dev);
>> + media_device_cleanup(&vid->media_dev);
>> + v4l2_device_disconnect(&vid->v4l2_dev);
>> + v4l2_device_put(&vid->v4l2_dev);
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id host1x_video_subdevs[] = {
>> + { .compatible = "nvidia,tegra210-csi", },
>> + { .compatible = "nvidia,tegra210-vi", },
>> + { }
>> +};
>> +
>> +static struct host1x_driver host1x_video_driver = {
>> + .driver = {
>> + .name = "tegra-video",
>> + },
>> + .probe = host1x_video_probe,
>> + .remove = host1x_video_remove,
>> + .subdevs = host1x_video_subdevs,
>> +};
>> +
>> +static struct platform_driver * const drivers[] = {
>> + &tegra_csi_driver,
>> + &tegra_vi_driver,
>> +};
>> +
>> +static int __init host1x_video_init(void)
>> +{
>> + int err;
>> +
>> + err = host1x_driver_register(&host1x_video_driver);
>> + if (err < 0)
>> + return err;
>> +
>> + err = platform_register_drivers(drivers, ARRAY_SIZE(drivers));
>> + if (err < 0)
>> + goto unregister_host1x;
>> +
>> + return 0;
>> +
>> +unregister_host1x:
>> + host1x_driver_unregister(&host1x_video_driver);
>> + return err;
>> +}
>> +module_init(host1x_video_init);
>> +
>> +static void __exit host1x_video_exit(void)
>> +{
>> + platform_unregister_drivers(drivers, ARRAY_SIZE(drivers));
>> + host1x_driver_unregister(&host1x_video_driver);
>> +}
>> +module_exit(host1x_video_exit);
>> +
>> +MODULE_AUTHOR("Sowjanya Komatineni <skomatineni@nvidia.com>");
>> +MODULE_DESCRIPTION("NVIDIA Tegra Host1x Video driver");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/staging/media/tegra/tegra-video.h b/drivers/staging/media/tegra/tegra-video.h
>> new file mode 100644
>> index 0000000..1e2ae64
>> --- /dev/null
>> +++ b/drivers/staging/media/tegra/tegra-video.h
>> @@ -0,0 +1,32 @@
>> +/* SPDX-License-Identifier: GPL-2.0-only */
>> +/*
>> + * Copyright (C) 2020 NVIDIA CORPORATION. All rights reserved.
>> + */
>> +
>> +#ifndef __TEGRA_VIDEO_H__
>> +#define __TEGRA_VIDEO_H__
>> +
>> +#include <linux/host1x.h>
>> +
>> +#include <media/media-device.h>
>> +#include <media/media-entity.h>
>> +#include <media/v4l2-async.h>
>> +#include <media/v4l2-ctrls.h>
>> +#include <media/v4l2-device.h>
>> +#include <media/v4l2-dev.h>
>> +#include <media/videobuf2-v4l2.h>
>> +
>> +#include "tegra-vi.h"
>> +#include "tegra-csi.h"
>> +
>> +struct tegra_video_device {
>> + struct v4l2_device v4l2_dev;
>> + struct media_device media_dev;
>> + struct tegra_vi *vi;
>> + struct tegra_csi *csi;
>> +};
>> +
>> +extern struct platform_driver tegra_vi_driver;
>> +extern struct platform_driver tegra_csi_driver;
>> +
>> +#endif
>> diff --git a/drivers/staging/media/tegra/tegra210.c b/drivers/staging/media/tegra/tegra210.c
>> new file mode 100644
>> index 0000000..eb547bb
>> --- /dev/null
>> +++ b/drivers/staging/media/tegra/tegra210.c
>> @@ -0,0 +1,754 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * Copyright (C) 2020 NVIDIA CORPORATION. All rights reserved.
>> + */
>> +
>> +/*
>> + * This source file contains both VI and CSI specific operations and
>> + * registers accessors.
>> + */
>> +#include <linux/clk.h>
>> +#include <linux/clk/tegra.h>
>> +#include <linux/delay.h>
>> +#include <linux/freezer.h>
>> +#include <linux/completion.h>
>> +
>> +#include "tegra-common.h"
>> +#include "tegra-csi.h"
>> +#include "tegra-vi.h"
>> +#include "tegra210.h"
>> +
>> +#define TEGRA210_CSI_PORT_OFFSET 0x34
>> +#define TEGRA210_CSI_CIL_OFFSET 0x0f4
>> +#define TEGRA210_CSI_TPG_OFFSET 0x18c
>> +
>> +#define CSI_PP_OFFSET(block) ((block) * 0x800)
>> +#define TEGRA210_VI_CSI_BASE(x) (0x100 + (x) * 0x100)
>> +
>> +/* Tegra210 VI registers accessors */
>> +static void tegra_vi_write(struct tegra_vi_channel *chan, unsigned int addr,
>> + u32 val)
>> +{
>> + writel(val, chan->vi->iomem + addr);
>> +}
>> +
>> +static u32 tegra_vi_read(struct tegra_vi_channel *chan, unsigned int addr)
>> +{
>> + return readl(chan->vi->iomem + addr);
>> +}
>> +
>> +/* Tegra210 VI_CSI registers accessors */
>> +static void vi_csi_write(struct tegra_vi_channel *chan, unsigned int addr,
>> + u32 val)
>> +{
>> + void __iomem *vi_csi_base;
>> +
>> + vi_csi_base = chan->vi->iomem + TEGRA210_VI_CSI_BASE(chan->portno);
>> +
>> + writel(val, vi_csi_base + addr);
>> +}
>> +
>> +static u32 vi_csi_read(struct tegra_vi_channel *chan, unsigned int addr)
>> +{
>> + void __iomem *vi_csi_base;
>> +
>> + vi_csi_base = chan->vi->iomem + TEGRA210_VI_CSI_BASE(chan->portno);
>> +
>> + return readl(vi_csi_base + addr);
>> +}
>> +
>> +/*
>> + * Tegra210 VI channel capture operations
>> + */
>> +static int tegra_channel_capture_setup(struct tegra_vi_channel *chan)
>> +{
>> + u32 height = chan->format.height;
>> + u32 width = chan->format.width;
>> + u32 format = chan->fmtinfo->img_fmt;
>> + u32 data_type = chan->fmtinfo->img_dt;
>> + u32 word_count = (width * chan->fmtinfo->bit_width) / 8;
>> +
>> + vi_csi_write(chan, TEGRA_VI_CSI_ERROR_STATUS, 0xffffffff);
>> + vi_csi_write(chan, TEGRA_VI_CSI_IMAGE_DEF,
>> + ((chan->pg_mode ? 0 : 1) << BYPASS_PXL_TRANSFORM_OFFSET) |
>> + (format << IMAGE_DEF_FORMAT_OFFSET) |
>> + IMAGE_DEF_DEST_MEM);
>> + vi_csi_write(chan, TEGRA_VI_CSI_IMAGE_DT, data_type);
>> + vi_csi_write(chan, TEGRA_VI_CSI_IMAGE_SIZE_WC, word_count);
>> + vi_csi_write(chan, TEGRA_VI_CSI_IMAGE_SIZE,
>> + (height << IMAGE_SIZE_HEIGHT_OFFSET) | width);
>> + return 0;
>> +}
>> +
>> +static void tegra_channel_vi_soft_reset(struct tegra_vi_channel *chan)
>> +{
>> + /* disable clock gating to enable continuous clock */
>> + tegra_vi_write(chan, TEGRA_VI_CFG_CG_CTRL, 0);
>> + /*
>> + * Soft reset memory client interface, pixel format logic, sensor
>> + * control logic, and a shadow copy logic to bring VI to clean state.
>> + */
>> + vi_csi_write(chan, TEGRA_VI_CSI_SW_RESET, 0xf);
>> + usleep_range(100, 200);
>> + vi_csi_write(chan, TEGRA_VI_CSI_SW_RESET, 0x0);
>> +
>> + /* enable back VI clock gating */
>> + tegra_vi_write(chan, TEGRA_VI_CFG_CG_CTRL, VI_CG_2ND_LEVEL_EN);
>> +}
>> +
>> +static void tegra_channel_capture_error_recover(struct tegra_vi_channel *chan)
>> +{
>> + u32 val;
>> +
>> + /*
>> + * Recover VI and CSI hardware blocks in case of missing frame start
>> + * events due to source not streaming or noisy csi inputs from the
>> + * external source or many outstanding frame start or MW_ACK_DONE
>> + * events which can cause CSI and VI hardware hang.
>> + * This helps to have a clean capture for next frame.
>> + */
>> + val = vi_csi_read(chan, TEGRA_VI_CSI_ERROR_STATUS);
>> + dev_dbg(&chan->video->dev, "TEGRA_VI_CSI_ERROR_STATUS 0x%08x\n", val);
>> + vi_csi_write(chan, TEGRA_VI_CSI_ERROR_STATUS, val);
>> +
>> + val = tegra_vi_read(chan, TEGRA_VI_CFG_VI_INCR_SYNCPT_ERROR);
>> + dev_dbg(&chan->video->dev,
>> + "TEGRA_VI_CFG_VI_INCR_SYNCPT_ERROR 0x%08x\n", val);
>> + tegra_vi_write(chan, TEGRA_VI_CFG_VI_INCR_SYNCPT_ERROR, val);
>> +
>> + /* disable the stream */
>> + tegra_channel_set_stream(chan, false);
>> +
>> + /* recover VI and CSI blocks by issuing software reset */
>> + tegra_channel_csi_error_recover(chan);
>> + tegra_channel_vi_soft_reset(chan);
>> +
>> + /* re-init VI and enable back the stream */
>> + tegra_channel_capture_setup(chan);
>> + tegra_channel_set_stream(chan, true);
>> +}
>> +
>> +static struct tegra_channel_buffer *
>> +dequeue_buf_done(struct tegra_vi_channel *chan)
>> +{
>> + struct tegra_channel_buffer *buf = NULL;
>> +
>> + spin_lock(&chan->done_lock);
>> + if (list_empty(&chan->done)) {
>> + spin_unlock(&chan->done_lock);
>> + return NULL;
>> + }
>> +
>> + buf = list_entry(chan->done.next, struct tegra_channel_buffer,
>> + queue);
>> + if (buf)
>> + list_del_init(&buf->queue);
>> +
>> + spin_unlock(&chan->done_lock);
>> +
>> + return buf;
>> +}
>> +
>> +static void release_buffer(struct tegra_vi_channel *chan,
>> + struct tegra_channel_buffer *buf,
>> + enum vb2_buffer_state state)
>> +{
>> + struct vb2_v4l2_buffer *vb = &buf->buf;
>> +
>> + vb->sequence = chan->sequence++;
>> + vb->field = V4L2_FIELD_NONE;
>> + vb->vb2_buf.timestamp = ktime_get_ns();
>> + vb2_buffer_done(&vb->vb2_buf, state);
>> +}
>> +
>> +static int tegra_channel_capture_frame(struct tegra_vi_channel *chan,
>> + struct tegra_channel_buffer *buf)
>> +{
>> + int err = 0;
>> + u32 thresh, value, frame_start, mw_ack_done;
>> + int bytes_per_line = chan->format.bytesperline;
>> +
>> + /* program buffer address by using surface 0 */
>> + vi_csi_write(chan, TEGRA_VI_CSI_SURFACE0_OFFSET_MSB,
>> + (u64)buf->addr >> 32);
>> + vi_csi_write(chan, TEGRA_VI_CSI_SURFACE0_OFFSET_LSB, buf->addr);
>> + vi_csi_write(chan, TEGRA_VI_CSI_SURFACE0_STRIDE, bytes_per_line);
>> +
>> + /*
>> + * Tegra VI block interacts with host1x syncpt for synchronizing
>> + * programmed condition of capture state and hardware operation.
>> + * Frame start and Memory write acknowledge syncpts has their own
>> + * FIFO of depth 2.
>> + *
>> + * Syncpoint trigger conditions set through VI_INCR_SYNCPT register
>> + * are added to HW syncpt FIFO and when the HW triggers, syncpt
>> + * condition is removed from the FIFO and counter at syncpoint index
>> + * will be incremented by the hardware and software can wait for
>> + * counter to reach threshold to synchronize capturing frame with the
>> + * hardware capture events.
>> + */
>> +
>> + /* increase channel syncpoint threshold for FRAME_START */
>> + thresh = host1x_syncpt_incr_max(chan->frame_start_sp, 1);
>> +
>> + /* Program FRAME_START trigger condition syncpt request */
>> + frame_start = VI_CSI_PP_FRAME_START(chan->portno);
>> + value = VI_CFG_VI_INCR_SYNCPT_COND(frame_start) |
>> + host1x_syncpt_id(chan->frame_start_sp);
>> + tegra_vi_write(chan, TEGRA_VI_CFG_VI_INCR_SYNCPT, value);
>> +
>> + /* increase channel syncpoint threshold for MW_ACK_DONE */
>> + buf->mw_ack_sp_thresh = host1x_syncpt_incr_max(chan->mw_ack_sp, 1);
>> +
>> + /* Program MW_ACK_DONE trigger condition syncpt request */
>> + mw_ack_done = VI_CSI_MW_ACK_DONE(chan->portno);
>> + value = VI_CFG_VI_INCR_SYNCPT_COND(mw_ack_done) |
>> + host1x_syncpt_id(chan->mw_ack_sp);
>> + tegra_vi_write(chan, TEGRA_VI_CFG_VI_INCR_SYNCPT, value);
>> +
>> + /* enable single shot capture */
>> + vi_csi_write(chan, TEGRA_VI_CSI_SINGLE_SHOT, SINGLE_SHOT_CAPTURE);
>> + chan->capture_reqs++;
>> +
>> + /* wait for syncpt counter to reach frame start event threshold */
>> + err = host1x_syncpt_wait(chan->frame_start_sp, thresh,
>> + TEGRA_VI_SYNCPT_WAIT_TIMEOUT, &value);
>> + if (err) {
>> + dev_err(&chan->video->dev,
>> + "frame start syncpt timeout: %d\n", err);
>> + /* increment syncpoint counter for timedout events */
>> + host1x_syncpt_incr(chan->frame_start_sp);
>> + spin_lock(&chan->sp_incr_lock);
>> + host1x_syncpt_incr(chan->mw_ack_sp);
>> + spin_unlock(&chan->sp_incr_lock);
>> + /* clear errors and recover */
>> + tegra_channel_capture_error_recover(chan);
>> + release_buffer(chan, buf, VB2_BUF_STATE_ERROR);
>> + return err;
>> + }
>> +
>> + /* move buffer to capture done queue */
>> + spin_lock(&chan->done_lock);
>> + list_add_tail(&buf->queue, &chan->done);
>> + spin_unlock(&chan->done_lock);
>> +
>> + /* wait up kthread for capture done */
>> + wake_up_interruptible(&chan->done_wait);
>> +
>> + return 0;
>> +}
>> +
>> +static void tegra_channel_capture_done(struct tegra_vi_channel *chan,
>> + struct tegra_channel_buffer *buf)
>> +{
>> + enum vb2_buffer_state state = VB2_BUF_STATE_DONE;
>> + u32 value;
>> + int ret;
>> +
>> + /* wait for syncpt counter to reach MW_ACK_DONE event threshold */
>> + ret = host1x_syncpt_wait(chan->mw_ack_sp, buf->mw_ack_sp_thresh,
>> + TEGRA_VI_SYNCPT_WAIT_TIMEOUT, &value);
>> + if (ret) {
>> + dev_err(&chan->video->dev,
>> + "MW_ACK_DONE syncpt timeout: %d\n", ret);
>> + state = VB2_BUF_STATE_ERROR;
>> + /* increment syncpoint counter for timedout event */
>> + spin_lock(&chan->sp_incr_lock);
>> + host1x_syncpt_incr(chan->mw_ack_sp);
>> + spin_unlock(&chan->sp_incr_lock);
>> + }
>> +
>> + release_buffer(chan, buf, state);
>> +}
>> +
>> +static int chan_capture_kthread_start(void *data)
>> +{
>> + struct tegra_vi_channel *chan = data;
>> + struct tegra_channel_buffer *buf;
>> + int err = 0;
>> + int caps_inflight;
>> +
>> + set_freezable();
>
> Do you have a particular reason to use a kernel thread, instead of using
> the context of the user process (or threaded interrupt handler)?
>
>> +
>> + while (1) {
>> + try_to_freeze();
>> +
>> + wait_event_interruptible(chan->start_wait,
>> + !list_empty(&chan->capture) ||
>> + kthread_should_stop());
>> + /*
>> + * Frame start and MW_ACK_DONE syncpoint condition FIFOs are
>> + * of max depth 2. So make sure max 2 capture requests are
>> + * in process by the hardware at a time.
>> + */
>> + while (!(kthread_should_stop() || list_empty(&chan->capture))) {
>> + caps_inflight = chan->capture_reqs - chan->sequence;
>> + /*
>> + * Source is not streaming if error is non-zero.
>> + * So, do not dequeue buffers on capture error or when
>> + * syncpoint requests in FIFO are full.
>> + */
>> + if (err || caps_inflight >= SYNCPT_FIFO_DEPTH)
>> + break;
>> +
>> + /* dequeue the buffer and start capture */
>> + spin_lock(&chan->start_lock);
>> + if (list_empty(&chan->capture))
>> + break;
>> + buf = list_entry(chan->capture.next,
>> + struct tegra_channel_buffer, queue);
>> + list_del_init(&buf->queue);
>> + spin_unlock(&chan->start_lock);
>> +
>> + err = tegra_channel_capture_frame(chan, buf);
>> + if (err)
>> + vb2_queue_error(&chan->queue);
>> + }
>> +
>> + if (kthread_should_stop())
>> + break;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int chan_capture_kthread_finish(void *data)
>> +{
>> + struct tegra_vi_channel *chan = data;
>> + struct tegra_channel_buffer *buf;
>> +
>> + set_freezable();
>> +
>> + while (1) {
>> + try_to_freeze();
>> +
>> + wait_event_interruptible(chan->done_wait,
>> + !list_empty(&chan->done) ||
>> + kthread_should_stop());
>> + /* dequeue buffers and finish capture */
>> + buf = dequeue_buf_done(chan);
>> + while (buf) {
>> + tegra_channel_capture_done(chan, buf);
>> + buf = dequeue_buf_done(chan);
>> + }
>> +
>> + if (kthread_should_stop())
>> + break;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +int tegra210_vi_start_streaming(struct vb2_queue *vq, u32 count)
>> +{
>> + struct tegra_vi_channel *chan = vb2_get_drv_priv(vq);
>> + struct media_pipeline *pipe = &chan->video->pipe;
>> + int ret;
>> +
>> + tegra_vi_write(chan, TEGRA_VI_CFG_CG_CTRL, VI_CG_2ND_LEVEL_EN);
>> +
>> + /* clear errors */
>> + vi_csi_write(chan, TEGRA_VI_CSI_ERROR_STATUS, 0xffffffff);
>> +
>> + /*
>> + * Sync point FIFO full stalls the host interface.
>> + * Setting NO_STALL will drop INCR_SYNCPT methods when fifos are
>> + * full and the corresponding condition bits in INCR_SYNCPT_ERROR
>> + * register will be set.
>> + * This allows SW to process error recovery.
>> + */
>> + tegra_vi_write(chan, TEGRA_VI_CFG_VI_INCR_SYNCPT_CNTRL,
>> + TEGRA_VI_CFG_VI_INCR_SYNCPT_NO_STALL);
>> +
>> + /* start the pipeline */
>> + ret = media_pipeline_start(&chan->video->entity, pipe);
>> + if (ret < 0)
>> + goto error_pipeline_start;
>> +
>> + tegra_channel_capture_setup(chan);
>> + ret = tegra_channel_set_stream(chan, true);
>> + if (ret < 0)
>> + goto error_set_stream;
>> +
>> + chan->capture_reqs = 0;
>> + chan->sequence = 0;
>> +
>> + /* start kthreads to capture data to buffer and return them */
>> + chan->kthread_start_capture = kthread_run(chan_capture_kthread_start,
>> + chan, "%s:0",
>> + chan->video->name);
>> + if (IS_ERR(chan->kthread_start_capture)) {
>> + ret = PTR_ERR(chan->kthread_start_capture);
>> + chan->kthread_start_capture = NULL;
>> + dev_err(&chan->video->dev,
>> + "failed to run capture start kthread: %d\n", ret);
>> + goto error_kthread_start;
>> + }
>> +
>> + chan->kthread_finish_capture = kthread_run(chan_capture_kthread_finish,
>> + chan, "%s:1",
>> + chan->video->name);
>> + if (IS_ERR(chan->kthread_finish_capture)) {
>> + ret = PTR_ERR(chan->kthread_finish_capture);
>> + chan->kthread_finish_capture = NULL;
>> + dev_err(&chan->video->dev,
>> + "failed to run capture finish kthread: %d\n", ret);
>> + goto error_kthread_done;
>> + }
>> +
>> + return 0;
>> +
>> +error_kthread_done:
>> + kthread_stop(chan->kthread_start_capture);
>> +error_kthread_start:
>> + tegra_channel_set_stream(chan, false);
>> +error_set_stream:
>> + media_pipeline_stop(&chan->video->entity);
>> +error_pipeline_start:
>> + vq->start_streaming_called = 0;
>> + tegra_channel_release_buffers(chan, VB2_BUF_STATE_QUEUED);
>> + return ret;
>> +}
>> +
>> +void tegra210_vi_stop_streaming(struct vb2_queue *vq)
>> +{
>> + struct tegra_vi_channel *chan = vb2_get_drv_priv(vq);
>> +
>> + if (chan->kthread_start_capture) {
>> + kthread_stop(chan->kthread_start_capture);
>> + chan->kthread_start_capture = NULL;
>> + }
>> +
>> + if (chan->kthread_finish_capture) {
>> + kthread_stop(chan->kthread_finish_capture);
>> + chan->kthread_finish_capture = NULL;
>> + }
>> +
>> + tegra_channel_release_buffers(chan, VB2_BUF_STATE_ERROR);
>> + tegra_channel_set_stream(chan, false);
>> + media_pipeline_stop(&chan->video->entity);
>> +}
>> +
>> +/* Tegra210 CSI PHY registers accessors */
>> +static void csi_write(struct tegra_csi *csi, u8 portno, unsigned int addr,
>> + u32 val)
>> +{
>> + void __iomem *csi_pp_base;
>> +
>> + csi_pp_base = csi->iomem + CSI_PP_OFFSET(portno >> 1);
>> +
>> + writel(val, csi_pp_base + addr);
>> +}
>> +
>> +/* Tegra210 CSI Pixel parser registers accessors */
>> +static void pp_write(struct tegra_csi *csi, u8 portno, u32 addr, u32 val)
>> +{
>> + void __iomem *csi_pp_base;
>> + unsigned int offset;
>> +
>> + csi_pp_base = csi->iomem + CSI_PP_OFFSET(portno >> 1);
>> + offset = (portno % CSI_PORTS_PER_BRICK) * TEGRA210_CSI_PORT_OFFSET;
>> +
>> + writel(val, csi_pp_base + offset + addr);
>> +}
>> +
>> +static u32 pp_read(struct tegra_csi *csi, u8 portno, u32 addr)
>> +{
>> + void __iomem *csi_pp_base;
>> + unsigned int offset;
>> +
>> + csi_pp_base = csi->iomem + CSI_PP_OFFSET(portno >> 1);
>> + offset = (portno % CSI_PORTS_PER_BRICK) * TEGRA210_CSI_PORT_OFFSET;
>> +
>> + return readl(csi_pp_base + offset + addr);
>> +}
>> +
>> +/* Tegra210 CSI CIL A/B port registers accessors */
>> +static void cil_write(struct tegra_csi *csi, u8 portno, u32 addr, u32 val)
>> +{
>> + void __iomem *csi_cil_base;
>> + unsigned int offset;
>> +
>> + csi_cil_base = csi->iomem + CSI_PP_OFFSET(portno >> 1) +
>> + TEGRA210_CSI_CIL_OFFSET;
>> + offset = (portno % CSI_PORTS_PER_BRICK) * TEGRA210_CSI_PORT_OFFSET;
>> +
>> + writel(val, csi_cil_base + offset + addr);
>> +}
>> +
>> +static u32 cil_read(struct tegra_csi *csi, u8 portno, u32 addr)
>> +{
>> + void __iomem *csi_cil_base;
>> + unsigned int offset;
>> +
>> + csi_cil_base = csi->iomem + CSI_PP_OFFSET(portno >> 1) +
>> + TEGRA210_CSI_CIL_OFFSET;
>> + offset = (portno % CSI_PORTS_PER_BRICK) * TEGRA210_CSI_PORT_OFFSET;
>> +
>> + return readl(csi_cil_base + offset + addr);
>> +}
>> +
>> +/* Tegra210 CSI Test pattern generator registers accessor */
>> +static void tpg_write(struct tegra_csi *csi, u8 portno, unsigned int addr,
>> + u32 val)
>> +{
>> + void __iomem *csi_pp_base;
>> + unsigned int offset;
>> +
>> + csi_pp_base = csi->iomem + CSI_PP_OFFSET(portno >> 1);
>> + offset = (portno % CSI_PORTS_PER_BRICK) * TEGRA210_CSI_PORT_OFFSET +
>> + TEGRA210_CSI_TPG_OFFSET;
>> +
>> + writel(val, csi_pp_base + offset + addr);
>> +}
>> +
>> +/*
>> + * Tegra210 CSI operations
>> + */
>> +void tegra210_csi_error_recover(struct tegra_csi_channel *csi_chan)
>> +{
>> + struct tegra_csi *csi = csi_chan->csi;
>> + unsigned int port_num = csi_chan->csi_port_num;
>> + u32 val;
>> +
>> + /*
>> + * Recover CSI hardware in case of capture errors by issuing
>> + * software reset to CSICIL sensor, pixel parser, and clear errors
>> + * to have clean capture on next streaming.
>> + */
>> + val = pp_read(csi, port_num, TEGRA_CSI_PIXEL_PARSER_STATUS);
>> + dev_dbg(csi->dev, "TEGRA_CSI_PIXEL_PARSER_STATUS 0x%08x\n", val);
>> +
>> + val = cil_read(csi, port_num, TEGRA_CSI_CIL_STATUS);
>> + dev_dbg(csi->dev, "TEGRA_CSI_CIL_STATUS 0x%08x\n", val);
>> +
>> + val = cil_read(csi, port_num, TEGRA_CSI_CILX_STATUS);
>> + dev_dbg(csi->dev, "TEGRA_CSI_CILX_STATUS 0x%08x\n", val);
>> +
>> + if (csi_chan->numlanes == 4) {
>> + /* reset CSI CIL sensor */
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_SW_SENSOR_RESET, 0x1);
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CIL_SW_SENSOR_RESET, 0x1);
>> + /*
>> + * SW_STATUS_RESET resets all status bits of PPA, PPB, CILA,
>> + * CILB status registers and debug counters.
>> + * So, SW_STATUS_RESET can be used only when CSI Brick is in
>> + * x4 mode.
>> + */
>> + csi_write(csi, port_num, TEGRA_CSI_CSI_SW_STATUS_RESET, 0x1);
>> +
>> + /* sleep for 20 clock cycles to drain the FIFO */
>> + usleep_range(10, 20);
>> +
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CIL_SW_SENSOR_RESET, 0x0);
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_SW_SENSOR_RESET, 0x0);
>> + csi_write(csi, port_num, TEGRA_CSI_CSI_SW_STATUS_RESET, 0x0);
>> + } else {
>> + /* reset CSICIL sensor */
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_SW_SENSOR_RESET, 0x1);
>> + usleep_range(10, 20);
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_SW_SENSOR_RESET, 0x0);
>> +
>> + /* clear the errors */
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_PARSER_STATUS,
>> + 0xffffffff);
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_STATUS, 0xffffffff);
>> + cil_write(csi, port_num, TEGRA_CSI_CILX_STATUS, 0xffffffff);
>> + }
>> +}
>> +
>> +int tegra210_csi_streaming(struct tegra_csi_channel *csi_chan, u8 pg_mode,
>> + int enable)
>> +{
>> + struct tegra_csi *csi = csi_chan->csi;
>> + unsigned int port_num = csi_chan->csi_port_num;
>> +
>> + if (enable) {
>> + csi_write(csi, port_num, TEGRA_CSI_CLKEN_OVERRIDE, 0);
>> +
>> + /* clean up status */
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_PARSER_STATUS,
>> + 0xffffffff);
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_STATUS, 0xffffffff);
>> + cil_write(csi, port_num, TEGRA_CSI_CILX_STATUS, 0xffffffff);
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_INTERRUPT_MASK, 0x0);
>> +
>> + /* CIL PHY registers setup */
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_PAD_CONFIG0, 0x0);
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_PHY_CONTROL, 0xa);
>> +
>> + /*
>> + * The CSI unit provides for connection of up to six cameras in
>> + * the system and is organized as three identical instances of
>> + * two MIPI support blocks, each with a separate 4-lane
>> + * interface that can be configured as a single camera with 4
>> + * lanes or as a dual camera with 2 lanes available for each
>> + * camera.
>> + */
>> + if (csi_chan->numlanes == 4) {
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CIL_STATUS, 0xffffffff);
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CILX_STATUS, 0xffffffff);
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CIL_INTERRUPT_MASK, 0x0);
>> +
>> + cil_write(csi, port_num,
>> + TEGRA_CSI_CIL_PAD_CONFIG0, BRICK_CLOCK_A_4X);
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CIL_PAD_CONFIG0, 0x0);
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CIL_INTERRUPT_MASK, 0x0);
>> + cil_write(csi, port_num + 1,
>> + TEGRA_CSI_CIL_PHY_CONTROL, 0xa);
>> + csi_write(csi, port_num, TEGRA_CSI_PHY_CIL_COMMAND,
>> + CSI_A_PHY_CIL_ENABLE | CSI_B_PHY_CIL_ENABLE);
>> + } else {
>> + u32 val = ((port_num & 1) == PORT_A) ?
>> + CSI_A_PHY_CIL_ENABLE | CSI_B_PHY_CIL_NOP :
>> + CSI_B_PHY_CIL_ENABLE | CSI_A_PHY_CIL_NOP;
>> + csi_write(csi, port_num, TEGRA_CSI_PHY_CIL_COMMAND,
>> + val);
>> + }
>> +
>> + /* CSI pixel parser registers setup */
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_STREAM_PP_COMMAND,
>> + (0xf << CSI_PP_START_MARKER_FRAME_MAX_OFFSET) |
>> + CSI_PP_SINGLE_SHOT_ENABLE | CSI_PP_RST);
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_PARSER_INTERRUPT_MASK,
>> + 0x0);
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_STREAM_CONTROL0,
>> + CSI_PP_PACKET_HEADER_SENT |
>> + CSI_PP_DATA_IDENTIFIER_ENABLE |
>> + CSI_PP_WORD_COUNT_SELECT_HEADER |
>> + CSI_PP_CRC_CHECK_ENABLE | CSI_PP_WC_CHECK |
>> + CSI_PP_OUTPUT_FORMAT_STORE | CSI_PPA_PAD_LINE_NOPAD |
>> + CSI_PP_HEADER_EC_DISABLE | CSI_PPA_PAD_FRAME_NOPAD |
>> + (port_num & 1));
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_STREAM_CONTROL1,
>> + (0x1 << CSI_PP_TOP_FIELD_FRAME_OFFSET) |
>> + (0x1 << CSI_PP_TOP_FIELD_FRAME_MASK_OFFSET));
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_STREAM_GAP,
>> + 0x14 << PP_FRAME_MIN_GAP_OFFSET);
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_STREAM_EXPECTED_FRAME,
>> + 0x0);
>> + pp_write(csi, port_num, TEGRA_CSI_INPUT_STREAM_CONTROL,
>> + (0x3f << CSI_SKIP_PACKET_THRESHOLD_OFFSET) |
>> + (csi_chan->numlanes - 1));
>> +
>> + /* TPG setup */
>> + if (pg_mode) {
>> + tpg_write(csi, port_num,
>> + TEGRA_CSI_PATTERN_GENERATOR_CTRL,
>> + ((pg_mode - 1) << PG_MODE_OFFSET) |
>> + PG_ENABLE);
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_BLANK,
>> + 8 << PG_VBLANK_OFFSET | 512);
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_PHASE, 0x0);
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_RED_FREQ,
>> + (0x10 << PG_RED_VERT_INIT_FREQ_OFFSET) |
>> + (0x10 << PG_RED_HOR_INIT_FREQ_OFFSET));
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_RED_FREQ_RATE,
>> + 0x0);
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_GREEN_FREQ,
>> + (0x10 << PG_GREEN_VERT_INIT_FREQ_OFFSET) |
>> + (0x10 << PG_GREEN_HOR_INIT_FREQ_OFFSET));
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_GREEN_FREQ_RATE,
>> + 0x0);
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_BLUE_FREQ,
>> + (0x10 << PG_BLUE_VERT_INIT_FREQ_OFFSET) |
>> + (0x10 << PG_BLUE_HOR_INIT_FREQ_OFFSET));
>> + tpg_write(csi, port_num, TEGRA_CSI_PG_BLUE_FREQ_RATE,
>> + 0x0);
>> + }
>> +
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_STREAM_PP_COMMAND,
>> + (0xf << CSI_PP_START_MARKER_FRAME_MAX_OFFSET) |
>> + CSI_PP_SINGLE_SHOT_ENABLE | CSI_PP_ENABLE);
>> + } else {
>> + u32 val = pp_read(csi, port_num,
>> + TEGRA_CSI_PIXEL_PARSER_STATUS);
>> +
>> + dev_dbg(csi->dev, "TEGRA_CSI_PIXEL_PARSER_STATUS 0x%08x\n",
>> + val);
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_PARSER_STATUS, val);
>> +
>> + val = cil_read(csi, port_num, TEGRA_CSI_CIL_STATUS);
>> + dev_dbg(csi->dev, "TEGRA_CSI_CIL_STATUS 0x%08x\n", val);
>> + cil_write(csi, port_num, TEGRA_CSI_CIL_STATUS, val);
>> +
>> + val = cil_read(csi, port_num, TEGRA_CSI_CILX_STATUS);
>> + dev_dbg(csi->dev, "TEGRA_CSI_CILX_STATUS 0x%08x\n", val);
>> + cil_write(csi, port_num, TEGRA_CSI_CILX_STATUS, val);
>> +
>> + pp_write(csi, port_num, TEGRA_CSI_PIXEL_STREAM_PP_COMMAND,
>> + (0xf << CSI_PP_START_MARKER_FRAME_MAX_OFFSET) |
>> + CSI_PP_DISABLE);
>> +
>> + if (pg_mode) {
>> + tpg_write(csi, port_num,
>> + TEGRA_CSI_PATTERN_GENERATOR_CTRL,
>> + PG_DISABLE);
>> + return 0;
>> + }
>> +
>> + if (csi_chan->numlanes == 4) {
>> + csi_write(csi, port_num, TEGRA_CSI_PHY_CIL_COMMAND,
>> + CSI_A_PHY_CIL_DISABLE |
>> + CSI_B_PHY_CIL_DISABLE);
>> +
>> + } else {
>> + u32 val = ((port_num & 1) == PORT_A) ?
>> + CSI_A_PHY_CIL_DISABLE | CSI_B_PHY_CIL_NOP :
>> + CSI_B_PHY_CIL_DISABLE | CSI_A_PHY_CIL_NOP;
>> + csi_write(csi, port_num, TEGRA_CSI_PHY_CIL_COMMAND,
>> + val);
>> + }
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +int tegra210_csi_hw_init(struct tegra_csi *csi)
>> +{
>> + int ret;
>> +
>> + csi->csi_clk = devm_clk_get(csi->dev, "csi");
>> + if (IS_ERR(csi->csi_clk)) {
>> + ret = PTR_ERR(csi->csi_clk);
>> + dev_err(csi->dev, "failed to get csi clock: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + csi->tpg_clk = devm_clk_get(csi->dev, "csi_tpg");
>> + if (IS_ERR(csi->tpg_clk)) {
>> + ret = PTR_ERR(csi->tpg_clk);
>> + dev_err(csi->dev, "failed to get csi_tpg clock: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + csi->cilab_clk = devm_clk_get(csi->dev, "cilab");
>> + if (IS_ERR(csi->cilab_clk)) {
>> + ret = PTR_ERR(csi->cilab_clk);
>> + dev_err(csi->dev, "failed to get cilab clock: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + csi->cilcd_clk = devm_clk_get(csi->dev, "cilcd");
>> + if (IS_ERR(csi->cilcd_clk)) {
>> + ret = PTR_ERR(csi->cilcd_clk);
>> + dev_err(csi->dev, "failed to get cilcd clock: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + csi->cilef_clk = devm_clk_get(csi->dev, "cile");
>> + if (IS_ERR(csi->cilef_clk)) {
>> + ret = PTR_ERR(csi->cilef_clk);
>> + dev_err(csi->dev, "failed to get cile clock: %d\n", ret);
>> + return ret;
>> + }
>> +
>
> devm_clk_bulk_get()?
>
>> + return 0;
>> +}
>> diff --git a/drivers/staging/media/tegra/tegra210.h b/drivers/staging/media/tegra/tegra210.h
>> new file mode 100644
>> index 0000000..c4548c5
>> --- /dev/null
>> +++ b/drivers/staging/media/tegra/tegra210.h
>> @@ -0,0 +1,192 @@
>> +/* SPDX-License-Identifier: GPL-2.0-only */
>> +/*
>> + * Copyright (C) 2020 NVIDIA CORPORATION. All rights reserved.
>> + */
>> +
>> +#ifndef __TEGRA210_H__
>> +#define __TEGRA210_H__
>> +
>> +/* Tegra210 VI registers */
>> +#define TEGRA_VI_SYNCPT_WAIT_TIMEOUT msecs_to_jiffies(200)
>> +#define TEGRA_VI_CFG_VI_INCR_SYNCPT 0x000
>> +#define VI_CFG_VI_INCR_SYNCPT_COND(x) (((x) & 0xff) << 8)
>> +#define VI_CSI_PP_LINE_START(port) (4 + (port) * 4)
>> +#define VI_CSI_PP_FRAME_START(port) (5 + (port) * 4)
>> +#define VI_CSI_MW_REQ_DONE(port) (6 + (port) * 4)
>> +#define VI_CSI_MW_ACK_DONE(port) (7 + (port) * 4)
>> +#define SYNCPT_FIFO_DEPTH 2
>> +
>> +#define TEGRA_VI_CFG_VI_INCR_SYNCPT_CNTRL 0x004
>> +#define TEGRA_VI_CFG_VI_INCR_SYNCPT_NO_STALL BIT(8)
>> +#define TEGRA_VI_CFG_VI_INCR_SYNCPT_ERROR 0x008
>> +#define TEGRA_VI_CFG_CTXSW 0x020
>> +#define TEGRA_VI_CFG_INTSTATUS 0x024
>> +#define TEGRA_VI_CFG_PWM_CONTROL 0x038
>> +#define TEGRA_VI_CFG_PWM_HIGH_PULSE 0x03c
>> +#define TEGRA_VI_CFG_PWM_LOW_PULSE 0x040
>> +#define TEGRA_VI_CFG_PWM_SELECT_PULSE_A 0x044
>> +#define TEGRA_VI_CFG_PWM_SELECT_PULSE_B 0x048
>> +#define TEGRA_VI_CFG_PWM_SELECT_PULSE_C 0x04c
>> +#define TEGRA_VI_CFG_PWM_SELECT_PULSE_D 0x050
>> +#define TEGRA_VI_CFG_VGP1 0x064
>> +#define TEGRA_VI_CFG_VGP2 0x068
>> +#define TEGRA_VI_CFG_VGP3 0x06c
>> +#define TEGRA_VI_CFG_VGP4 0x070
>> +#define TEGRA_VI_CFG_VGP5 0x074
>> +#define TEGRA_VI_CFG_VGP6 0x078
>> +#define TEGRA_VI_CFG_INTERRUPT_MASK 0x08c
>> +#define TEGRA_VI_CFG_INTERRUPT_TYPE_SELECT 0x090
>> +#define TEGRA_VI_CFG_INTERRUPT_POLARITY_SELECT 0x094
>> +#define TEGRA_VI_CFG_INTERRUPT_STATUS 0x098
>> +#define TEGRA_VI_CFG_VGP_SYNCPT_CONFIG 0x0ac
>> +#define TEGRA_VI_CFG_VI_SW_RESET 0x0b4
>> +#define TEGRA_VI_CFG_CG_CTRL 0x0b8
>> +#define VI_CG_2ND_LEVEL_EN 0x1
>> +#define TEGRA_VI_CFG_VI_MCCIF_FIFOCTRL 0x0e4
>> +#define TEGRA_VI_CFG_TIMEOUT_WCOAL_VI 0x0e8
>> +#define TEGRA_VI_CFG_DVFS 0x0f0
>> +#define TEGRA_VI_CFG_RESERVE 0x0f4
>> +#define TEGRA_VI_CFG_RESERVE_1 0x0f8
>> +
>> +/* Tegra210 CSI registers */
>> +#define TEGRA_VI_CSI_SW_RESET 0x000
>> +#define TEGRA_VI_CSI_SINGLE_SHOT 0x004
>> +#define SINGLE_SHOT_CAPTURE 0x1
>> +#define TEGRA_VI_CSI_SINGLE_SHOT_STATE_UPDATE 0x008
>> +#define TEGRA_VI_CSI_IMAGE_DEF 0x00c
>> +#define BYPASS_PXL_TRANSFORM_OFFSET 24
>> +#define IMAGE_DEF_FORMAT_OFFSET 16
>> +#define IMAGE_DEF_DEST_MEM 0x1
>> +#define TEGRA_VI_CSI_RGB2Y_CTRL 0x010
>> +#define TEGRA_VI_CSI_MEM_TILING 0x014
>> +#define TEGRA_VI_CSI_IMAGE_SIZE 0x018
>> +#define IMAGE_SIZE_HEIGHT_OFFSET 16
>> +#define TEGRA_VI_CSI_IMAGE_SIZE_WC 0x01c
>> +#define TEGRA_VI_CSI_IMAGE_DT 0x020
>> +#define TEGRA_VI_CSI_SURFACE0_OFFSET_MSB 0x024
>> +#define TEGRA_VI_CSI_SURFACE0_OFFSET_LSB 0x028
>> +#define TEGRA_VI_CSI_SURFACE1_OFFSET_MSB 0x02c
>> +#define TEGRA_VI_CSI_SURFACE1_OFFSET_LSB 0x030
>> +#define TEGRA_VI_CSI_SURFACE2_OFFSET_MSB 0x034
>> +#define TEGRA_VI_CSI_SURFACE2_OFFSET_LSB 0x038
>> +#define TEGRA_VI_CSI_SURFACE0_BF_OFFSET_MSB 0x03c
>> +#define TEGRA_VI_CSI_SURFACE0_BF_OFFSET_LSB 0x040
>> +#define TEGRA_VI_CSI_SURFACE1_BF_OFFSET_MSB 0x044
>> +#define TEGRA_VI_CSI_SURFACE1_BF_OFFSET_LSB 0x048
>> +#define TEGRA_VI_CSI_SURFACE2_BF_OFFSET_MSB 0x04c
>> +#define TEGRA_VI_CSI_SURFACE2_BF_OFFSET_LSB 0x050
>> +#define TEGRA_VI_CSI_SURFACE0_STRIDE 0x054
>> +#define TEGRA_VI_CSI_SURFACE1_STRIDE 0x058
>> +#define TEGRA_VI_CSI_SURFACE2_STRIDE 0x05c
>> +#define TEGRA_VI_CSI_SURFACE_HEIGHT0 0x060
>> +#define TEGRA_VI_CSI_ISPINTF_CONFIG 0x064
>> +#define TEGRA_VI_CSI_ERROR_STATUS 0x084
>> +#define TEGRA_VI_CSI_ERROR_INT_MASK 0x088
>> +#define TEGRA_VI_CSI_WD_CTRL 0x08c
>> +#define TEGRA_VI_CSI_WD_PERIOD 0x090
>> +
>> +/* Tegra210 CSI Pixel Parser registers: Starts from 0x838, offset 0x0 */
>> +#define TEGRA_CSI_INPUT_STREAM_CONTROL 0x000
>> +#define CSI_SKIP_PACKET_THRESHOLD_OFFSET 16
>> +
>> +#define TEGRA_CSI_PIXEL_STREAM_CONTROL0 0x004
>> +#define CSI_PP_PACKET_HEADER_SENT BIT(4)
>> +#define CSI_PP_DATA_IDENTIFIER_ENABLE BIT(5)
>> +#define CSI_PP_WORD_COUNT_SELECT_HEADER BIT(6)
>> +#define CSI_PP_CRC_CHECK_ENABLE BIT(7)
>> +#define CSI_PP_WC_CHECK BIT(8)
>> +#define CSI_PP_OUTPUT_FORMAT_STORE (0x3 << 16)
>> +#define CSI_PPA_PAD_LINE_NOPAD (0x2 << 24)
>> +#define CSI_PP_HEADER_EC_DISABLE (0x1 << 27)
>> +#define CSI_PPA_PAD_FRAME_NOPAD (0x2 << 28)
>> +
>> +#define TEGRA_CSI_PIXEL_STREAM_CONTROL1 0x008
>> +#define CSI_PP_TOP_FIELD_FRAME_OFFSET 0
>> +#define CSI_PP_TOP_FIELD_FRAME_MASK_OFFSET 4
>> +
>> +#define TEGRA_CSI_PIXEL_STREAM_GAP 0x00c
>> +#define PP_FRAME_MIN_GAP_OFFSET 16
>> +
>> +#define TEGRA_CSI_PIXEL_STREAM_PP_COMMAND 0x010
>> +#define CSI_PP_ENABLE 0x1
>> +#define CSI_PP_DISABLE 0x2
>> +#define CSI_PP_RST 0x3
>> +#define CSI_PP_SINGLE_SHOT_ENABLE (0x1 << 2)
>> +#define CSI_PP_START_MARKER_FRAME_MAX_OFFSET 12
>> +
>> +#define TEGRA_CSI_PIXEL_STREAM_EXPECTED_FRAME 0x014
>> +#define TEGRA_CSI_PIXEL_PARSER_INTERRUPT_MASK 0x018
>> +#define TEGRA_CSI_PIXEL_PARSER_STATUS 0x01c
>> +#define TEGRA_CSI_CSI_SW_SENSOR_RESET 0x020
>> +
>> +/* Tegra210 CSI PHY registers */
>> +/* CSI_PHY_CIL_COMMAND_0 offset 0x0d0 from TEGRA_CSI_PIXEL_PARSER_0_BASE */
>> +#define TEGRA_CSI_PHY_CIL_COMMAND 0x0d0
>> +#define CSI_A_PHY_CIL_NOP 0x0
>> +#define CSI_A_PHY_CIL_ENABLE 0x1
>> +#define CSI_A_PHY_CIL_DISABLE 0x2
>> +#define CSI_A_PHY_CIL_ENABLE_MASK 0x3
>> +#define CSI_B_PHY_CIL_NOP (0x0 << 8)
>> +#define CSI_B_PHY_CIL_ENABLE (0x1 << 8)
>> +#define CSI_B_PHY_CIL_DISABLE (0x2 << 8)
>> +#define CSI_B_PHY_CIL_ENABLE_MASK (0x3 << 8)
>> +
>> +#define TEGRA_CSI_CIL_PAD_CONFIG0 0x000
>> +#define BRICK_CLOCK_A_4X (0x1 << 16)
>> +#define BRICK_CLOCK_B_4X (0x2 << 16)
>> +#define TEGRA_CSI_CIL_PAD_CONFIG1 0x004
>> +#define TEGRA_CSI_CIL_PHY_CONTROL 0x008
>> +#define TEGRA_CSI_CIL_INTERRUPT_MASK 0x00c
>> +#define TEGRA_CSI_CIL_STATUS 0x010
>> +#define TEGRA_CSI_CILX_STATUS 0x014
>> +#define TEGRA_CSI_CIL_ESCAPE_MODE_COMMAND 0x018
>> +#define TEGRA_CSI_CIL_ESCAPE_MODE_DATA 0x01c
>> +#define TEGRA_CSI_CIL_SW_SENSOR_RESET 0x020
>> +
>> +#define TEGRA_CSI_PATTERN_GENERATOR_CTRL 0x000
>> +#define PG_MODE_OFFSET 2
>> +#define PG_ENABLE 0x1
>> +#define PG_DISABLE 0x0
>> +
>> +#define PG_VBLANK_OFFSET 16
>> +#define TEGRA_CSI_PG_BLANK 0x004
>> +#define TEGRA_CSI_PG_PHASE 0x008
>> +#define TEGRA_CSI_PG_RED_FREQ 0x00c
>> +#define PG_RED_VERT_INIT_FREQ_OFFSET 16
>> +#define PG_RED_HOR_INIT_FREQ_OFFSET 0
>> +
>> +#define TEGRA_CSI_PG_RED_FREQ_RATE 0x010
>> +#define TEGRA_CSI_PG_GREEN_FREQ 0x014
>> +#define PG_GREEN_VERT_INIT_FREQ_OFFSET 16
>> +#define PG_GREEN_HOR_INIT_FREQ_OFFSET 0
>> +
>> +#define TEGRA_CSI_PG_GREEN_FREQ_RATE 0x018
>> +#define TEGRA_CSI_PG_BLUE_FREQ 0x01c
>> +#define PG_BLUE_VERT_INIT_FREQ_OFFSET 16
>> +#define PG_BLUE_HOR_INIT_FREQ_OFFSET 0
>> +
>> +#define TEGRA_CSI_PG_BLUE_FREQ_RATE 0x020
>> +#define TEGRA_CSI_PG_AOHDR 0x024
>> +
>> +#define TEGRA_CSI_DPCM_CTRL_A 0xa2c
>> +#define TEGRA_CSI_DPCM_CTRL_B 0xa30
>> +
>> +/* Other CSI registers: Starts from 0xa44, offset 0x20c */
>> +#define TEGRA_CSI_STALL_COUNTER 0x20c
>> +#define TEGRA_CSI_CSI_READONLY_STATUS 0x210
>> +#define TEGRA_CSI_CSI_SW_STATUS_RESET 0x214
>> +#define TEGRA_CSI_CLKEN_OVERRIDE 0x218
>> +#define TEGRA_CSI_DEBUG_CONTROL 0x21c
>> +#define TEGRA_CSI_DEBUG_COUNTER_0 0x220
>> +#define TEGRA_CSI_DEBUG_COUNTER_1 0x224
>> +#define TEGRA_CSI_DEBUG_COUNTER_2 0x228
>> +
>> +/* Tegra210 CSI Pixel Parser registers */
>> +#define TEGRA_CSI_PIXEL_PARSER_0_BASE 0x0838
>> +#define TEGRA_CSI_PIXEL_PARSER_1_BASE 0x086c
>> +#define TEGRA_CSI_PIXEL_PARSER_2_BASE 0x1038
>> +#define TEGRA_CSI_PIXEL_PARSER_3_BASE 0x106c
>> +#define TEGRA_CSI_PIXEL_PARSER_4_BASE 0x1838
>> +#define TEGRA_CSI_PIXEL_PARSER_5_BASE 0x186c
>> +
>> +#endif
>