Re: [PATCH V3 12/17] dt-binding: mt8192: Add infra_ao reset bit

[Rex-BC Chen <rex-bc.chen@mediatek.com>]

On Mon, 2022-04-25 at 15:52 +0800, Krzysztof Kozlowski wrote:
> On 25/04/2022 07:01, Rex-BC Chen wrote:
> > On Sat, 2022-04-23 at 18:28 +0800, Krzysztof Kozlowski wrote:
> > > On 22/04/2022 08:01, Rex-BC Chen wrote:
> > > > To support reset of infra_ao, add the bit definition for
> > > > thermal/PCIe/SVS.
> > > > 
> > > > Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
> > > > ---
> > > >  include/dt-bindings/reset/mt8192-resets.h | 10 ++++++++++
> > > >  1 file changed, 10 insertions(+)
> > > > 
> > > > diff --git a/include/dt-bindings/reset/mt8192-resets.h
> > > > b/include/dt-bindings/reset/mt8192-resets.h
> > > > index be9a7ca245b9..d5f3433175c1 100644
> > > > --- a/include/dt-bindings/reset/mt8192-resets.h
> > > > +++ b/include/dt-bindings/reset/mt8192-resets.h
> > > > @@ -27,4 +27,14 @@
> > > >  
> > > >  #define MT8192_TOPRGU_SW_RST_NUM				
> > > > 23
> > > >  
> > > > +/* INFRA RST0 */
> > > > +#define MT8192_INFRA_RST0_LVTS_AP_RST				
> > > > 0
> > > > +/* INFRA RST2 */
> > > > +#define MT8192_INFRA_RST2_PCIE_PHY_RST				
> > > > 15
> > > > +/* INFRA RST3 */
> > > > +#define MT8192_INFRA_RST3_PTP_RST				
> > > > 5
> > > > +/* INFRA RST4 */
> > > > +#define MT8192_INFRA_RST4_LVTS_MCU				
> > > > 12
> > > > +#define MT8192_INFRA_RST4_PCIE_TOP				
> > > > 1
> > > 
> > > These should be the IDs of reset, not some register
> > > values/offsets.
> > > Therefore it is expected to have them incremented by 1.
> > > 
> > > 
> > 
> > Hello Krzysztof,
> > 
> > This is define bit.
> > 
> > There is serveral reset set for infra_ao while it's not serial.
> > For MT8192, it's 0x120/0x130/0x140/0x150/0x730.
> > We are implement #reset-cells = <2>, and we can use this reset
> > drive
> > more easier.
> > 
> > For example, in dts, we can define
> > infra_ao: syscon {
> > 	compatible = "mediatek,mt8192-infracfg", "syscon";
> >  	reg = <0 0x10001000 0 0x1000>;
> >  	#clock-cells = <1>;
> > 	#reset-cells = <2>;
> > };
> > 
> > thermal {
> > 	...
> > 	resets = <&infra_ao 0x730 MT8192_INFRA_RST4_LVTS_MCU>;
> > 	...
> > };
> > 
> > If it's acceptabel, I can update all bit difinition from 0 to 15
> > for
> > all reset set.
> 
> Bits are not acceptable, because you embed specific device
> programming
> model (register bits) into the binding.
> 
> These should be IDs, so decimal numbers incremented from 0, so:
> #define MT8192_INFRA_RST0_LVTS_AP_RST				0
> #define MT8192_INFRA_RST4_LVTS_MCU				1
> #define MT8192_INFRA_RST4_PCIE_TOP				2
> 
> And what is 0x730 in your example? It does not look like ID of a
> reset...
> 
> Entire changeset look wrong from DT point of view.
> 
> Best regards,
> Krzysztof

Hello Krzysztof,

Got it. I will modify them to reset index.
And the dts in my next version would somthing like this:

----
#define MT8192_INFRA_THERMAL_CTRL_RST			0
#define MT8192_INFRA_PEXTP_PHY_RST			79
#define MT8192_INFRA_PTP_RST				101
#define MT8192_INFRA_RST4_PCIE_TOP			129
#define MT8192_INFRA_THERMAL_CTRL_MCU_RST		140
----

infra_ao: syscon {
	compatible = "mediatek,mt8192-infracfg", "syscon";
	reg = <0 0x10001000 0 0x1000>;
	#clock-cells = <1>;
	#reset-cells = <1>;
};

thermal {
	...
	resets = <&infra_ao MT8192_INFRA_THERMAL_CTRL_MCU_RST>;
	...
};

BRs,
Rex