From: sashiko-bot@kernel.org
To: "Laurentiu Palcu" <laurentiu.palcu@oss.nxp.com>
Cc: linux-clk@vger.kernel.org, imx@lists.linux.dev,
devicetree@vger.kernel.org, dri-devel@lists.freedesktop.org,
robh@kernel.org, conor+dt@kernel.org, Frank.Li@kernel.org
Subject: Re: [PATCH v13 2/5] drm/imx: Add support for i.MX94 DCIF
Date: Fri, 20 Nov 2026 13:16:15 +0000 [thread overview]
Message-ID: <sashiko-outbox-225210@kernel.org> (raw)
In-Reply-To: <20261120-dcif-upstreaming-v13-2-966ac248773f@oss.nxp.com>
Thank you for your contribution! Sashiko AI review found 2 potential
issues to consider:
- [Medium] drm/imx/dcif: unclocked MMIO access after
pm_runtime_resume_and_get() fails
- [Medium] drm/imx: dcif: unbalanced clock disable if
dcif_runtime_resume() fails
--
commit aec0e23d14596f3fd993df3e2ad261bfab2bf2dd
Author: Sandor Yu <sandor.yu@nxp.com>
drm/imx: Add support for i.MX94 DCIF
This commit adds a DRM driver for the Display Control Interface (DCIF) on
NXP i.MX94 SoCs, supporting primary and overlay planes, alpha blending,
and display output CRC generation.
> diff --git a/drivers/gpu/drm/imx/dcif/dcif-crtc.c b/drivers/gpu/drm/imx/dcif/dcif-crtc.c
> new file mode 100644
> index 0000000000000..233e149929964
> --- /dev/null
> +++ b/drivers/gpu/drm/imx/dcif/dcif-crtc.c
> @@ -0,0 +1,710 @@
[ ... ]
> +static void dcif_crtc_atomic_enable(struct drm_crtc *crtc,
> + struct drm_atomic_commit *state)
> +{
> + struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
> + struct dcif_crtc_state *dcif_crtc_state = to_dcif_crtc_state(crtc_state);
> + struct drm_display_mode *adj = &crtc_state->adjusted_mode;
> + struct dcif_dev *dcif = crtc_to_dcif_dev(crtc);
> + struct drm_device *drm = crtc->dev;
> + int ret;
> +
> + dev_dbg(drm->dev, "mode " DRM_MODE_FMT "\n", DRM_MODE_ARG(adj));
> +
> + /* enable power when we start to set mode for CRTC */
> + ret = pm_runtime_resume_and_get(drm->dev);
> + if (ret < 0) {
> + drm_err(drm, "failed to resume DCIF, ret = %d\n", ret);
> + return;
> + }
> + dcif->crtc_pm_enabled = true;
[ ... ]
> +static void dcif_crtc_atomic_disable(struct drm_crtc *crtc,
> + struct drm_atomic_commit *state)
> +{
> + struct dcif_dev *dcif = crtc_to_dcif_dev(crtc);
> + struct drm_device *drm = crtc->dev;
> +
> + if (dcif->has_crc)
> + dcif_crc_source_disable(dcif, 0);
> +
> + dcif_disable_controller(dcif);
> + dcif_disable_plane_panic(dcif);
> +
> + drm_crtc_vblank_off(crtc);
> +
> + if (dcif->crtc_pm_enabled) {
> + dcif->crtc_pm_enabled = false;
> + pm_runtime_put_sync(drm->dev);
> + }
[Severity: Medium]
Can a failure in pm_runtime_resume_and_get() lead to unclocked MMIO
accesses and a synchronous external abort?
When pm_runtime_resume_and_get() fails in dcif_crtc_atomic_enable(),
dcif->crtc_pm_enabled stays false and the DCIF clocks remain disabled,
while crtc_state->active is still true. In the same commit tail,
drm_atomic_helper_commit_planes() then runs dcif_plane_atomic_update() and
dcif_crtc_atomic_flush(), writing to plane and shadow-load registers
without checking dcif->crtc_pm_enabled. Later, dcif_crtc_atomic_disable()
also accesses and polls DCIF registers in dcif_crc_source_disable(),
dcif_disable_controller(), and dcif_disable_plane_panic() before checking
dcif->crtc_pm_enabled.
> diff --git a/drivers/gpu/drm/imx/dcif/dcif-drv.c b/drivers/gpu/drm/imx/dcif/dcif-drv.c
> new file mode 100644
> index 0000000000000..80b554f1b6843
> --- /dev/null
> +++ b/drivers/gpu/drm/imx/dcif/dcif-drv.c
> @@ -0,0 +1,250 @@
[ ... ]
> +static int dcif_suspend(struct device *dev)
> +{
> + struct dcif_dev *dcif = dev_get_drvdata(dev);
> + int ret;
> +
> + ret = drm_mode_config_helper_suspend(&dcif->drm);
> + if (ret < 0)
> + return ret;
> +
> + if (pm_runtime_suspended(dev))
> + return 0;
> +
> + return dcif_runtime_suspend(dev);
> +}
> +
> +static int dcif_resume(struct device *dev)
> +{
> + struct dcif_dev *dcif = dev_get_drvdata(dev);
> + int ret;
> +
> + if (!pm_runtime_suspended(dev)) {
> + ret = dcif_runtime_resume(dev);
> + if (ret < 0)
> + return ret;
> + }
> +
> + return drm_mode_config_helper_resume(&dcif->drm);
> +}
[Severity: Medium]
Can a failure in dcif_runtime_resume() during system resume cause an
unbalanced clk_bulk_disable_unprepare()?
When the CRTC is active entering system suspend, the PM core holds an
extra runtime PM reference from device_prepare(), so the
pm_runtime_put_sync() in dcif_crtc_atomic_disable() leaves the device
runtime-active. dcif_suspend() then calls dcif_runtime_suspend() directly,
disabling dcif->clks while runtime_status remains RPM_ACTIVE.
If dcif_runtime_resume() fails in dcif_resume(), the device stays
RPM_ACTIVE with its clocks already disabled, and device_complete() ->
pm_runtime_put() will invoke dcif_runtime_suspend() a second time. Using
pm_runtime_force_suspend() and pm_runtime_force_resume() would keep the
runtime PM state in sync with the clocks.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261120-dcif-upstreaming-v13-0-966ac248773f@oss.nxp.com?part=2
next prev parent reply other threads:[~2026-11-20 13:16 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-20 12:50 [PATCH v13 0/5] Add support for i.MX94 DCIF Laurentiu Palcu
2026-11-20 12:50 ` [PATCH v13 1/5] dt-bindings: display: imx: Add " Laurentiu Palcu
2026-11-20 12:50 ` [PATCH v13 2/5] drm/imx: Add support for " Laurentiu Palcu
2026-11-20 13:16 ` sashiko-bot [this message]
2026-11-20 13:21 ` Laurentiu Palcu
2026-11-20 12:50 ` [PATCH v13 3/5] dt-bindings: clock: nxp,imx95-blk-ctl: Add LDB bridge child node Laurentiu Palcu
2026-11-20 12:50 ` [PATCH v13 4/5] arm64: dts: imx94: Add display pipeline nodes Laurentiu Palcu
2026-11-20 12:50 ` [PATCH v13 5/5] arm64: dts: imx943-evk: Add display support using IT6263 Laurentiu Palcu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=sashiko-outbox-225210@kernel.org \
--to=sashiko-bot@kernel.org \
--cc=Frank.Li@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=imx@lists.linux.dev \
--cc=laurentiu.palcu@oss.nxp.com \
--cc=linux-clk@vger.kernel.org \
--cc=robh@kernel.org \
--cc=sashiko-reviews@lists.linux.dev \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox