Re: [PATCH 07/39] dmaengine: ste_dma40: Only use addresses passed as configuration information

[Vinod Koul <vinod.koul@intel.com>]

On Wed, May 15, 2013 at 10:51:30AM +0100, Lee Jones wrote:
> Addresses are passed in from the client's driver via the invocation of
> dmaengine_slave_config(), so there's no need to fetch them from platform
> data too, hardwired or otherwise. This is a great step forward, as it
> elevates a large burden from platform data in the way of a look-up
> table.
> 
> Signed-off-by: Lee Jones <lee.jones@linaro.org>
> ---
Good code size reduction, always a good template for code improvements

Acked-by: Vinod Koul <vinod.koul@intel.com>

--
~Vinod
>  drivers/dma/ste_dma40.c |   51 ++++++++++-------------------------------------
>  1 file changed, 11 insertions(+), 40 deletions(-)
> 
> diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
> index ba84df8..57a127e 100644
> --- a/drivers/dma/ste_dma40.c
> +++ b/drivers/dma/ste_dma40.c
> @@ -1774,22 +1774,6 @@ static int d40_validate_conf(struct d40_chan *d40c,
>  		res = -EINVAL;
>  	}
>  
> -	if (conf->dir == STEDMA40_MEM_TO_PERIPH &&
> -	    d40c->base->plat_data->dev_tx[conf->dev_type] == 0 &&
> -	    d40c->runtime_addr == 0) {
> -		chan_err(d40c, "Invalid TX channel address (%d)\n",
> -			 conf->dev_type);
> -		res = -EINVAL;
> -	}
> -
> -	if (conf->dir == STEDMA40_PERIPH_TO_MEM &&
> -	    d40c->base->plat_data->dev_rx[conf->dev_type] == 0 &&
> -	    d40c->runtime_addr == 0) {
> -		chan_err(d40c, "Invalid RX channel address (%d)\n",
> -			 conf->dev_type);
> -		res = -EINVAL;
> -	}
> -
>  	if (conf->dir == STEDMA40_PERIPH_TO_PERIPH) {
>  		/*
>  		 * DMAC HW supports it. Will be added to this driver,
> @@ -2327,14 +2311,10 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
>  	if (sg_next(&sg_src[sg_len - 1]) == sg_src)
>  		desc->cyclic = true;
>  
> -	if (direction != DMA_TRANS_NONE) {
> -		dma_addr_t dev_addr = d40_get_dev_addr(chan, direction);
> -
> -		if (direction == DMA_DEV_TO_MEM)
> -			src_dev_addr = dev_addr;
> -		else if (direction == DMA_MEM_TO_DEV)
> -			dst_dev_addr = dev_addr;
> -	}
> +	if (direction == DMA_DEV_TO_MEM)
> +		src_dev_addr = chan->runtime_addr;
> +	else if (direction == DMA_MEM_TO_DEV)
> +		dst_dev_addr = chan->runtime_addr;
>  
>  	if (chan_is_logical(chan))
>  		ret = d40_prep_sg_log(chan, desc, sg_src, sg_dst,
> @@ -2782,15 +2762,8 @@ static int d40_set_runtime_config(struct dma_chan *chan,
>  	dst_maxburst = config->dst_maxburst;
>  
>  	if (config->direction == DMA_DEV_TO_MEM) {
> -		dma_addr_t dev_addr_rx =
> -			d40c->base->plat_data->dev_rx[cfg->dev_type];
> -
>  		config_addr = config->src_addr;
> -		if (dev_addr_rx)
> -			dev_dbg(d40c->base->dev,
> -				"channel has a pre-wired RX address %08x "
> -				"overriding with %08x\n",
> -				dev_addr_rx, config_addr);
> +
>  		if (cfg->dir != STEDMA40_PERIPH_TO_MEM)
>  			dev_dbg(d40c->base->dev,
>  				"channel was not configured for peripheral "
> @@ -2805,15 +2778,8 @@ static int d40_set_runtime_config(struct dma_chan *chan,
>  			dst_maxburst = src_maxburst;
>  
>  	} else if (config->direction == DMA_MEM_TO_DEV) {
> -		dma_addr_t dev_addr_tx =
> -			d40c->base->plat_data->dev_tx[cfg->dev_type];
> -
>  		config_addr = config->dst_addr;
> -		if (dev_addr_tx)
> -			dev_dbg(d40c->base->dev,
> -				"channel has a pre-wired TX address %08x "
> -				"overriding with %08x\n",
> -				dev_addr_tx, config_addr);
> +
>  		if (cfg->dir != STEDMA40_MEM_TO_PERIPH)
>  			dev_dbg(d40c->base->dev,
>  				"channel was not configured for memory "
> @@ -2833,6 +2799,11 @@ static int d40_set_runtime_config(struct dma_chan *chan,
>  		return -EINVAL;
>  	}
>  
> +	if (config_addr <= 0) {
> +		dev_err(d40c->base->dev, "no address supplied\n");
> +		return -EINVAL;
> +	}
> +
>  	if (src_maxburst * src_addr_width != dst_maxburst * dst_addr_width) {
>  		dev_err(d40c->base->dev,
>  			"src/dst width/maxburst mismatch: %d*%d != %d*%d\n",
> -- 
> 1.7.10.4
>